Nissan Murano Z51 (2008 year). Manual — part 316
SE-94
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Diagnostic Worksheet
INFOID:0000000003690556
PIIB8740E
Revision: 2008 October
2009 Murano
SQUEAK AND RATTLE TROUBLE DIAGNOSES
SE-95
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
PIIB8742E
Revision: 2008 October
2009 Murano
SE-96
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003685470
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors while ignition switch is
ON or engine is running, never use air or electric power tools or strike near the sensor(s) with a hammer.
Heavy vibration may activate the sensor(s), deploy the airbag(s), possibly cause serious injury.
When using air or electric power tools or hammers, always turn OFF ignition switch, disconnect the battery,
and wait 3 minutes or more before performing any service.
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
INFOID:0000000003685472
NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4.
Perform the necessary repair operation.
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT-III.
Revision: 2008 October
2009 Murano
PRECAUTIONS
SE-97
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Service Notice
INFOID:0000000003396986
• When removing or installing various parts, place a cloth or padding onto the vehicle body to prevent
scratches.
• Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to oil or
damage them.
• Apply sealing compound where necessary when installing parts.
• When applying sealing compound, be careful that the sealing compound does not protrude from parts.
• When replacing any metal parts (for example body outer panel, members, etc.), be sure to take rust preven-
tion measures.
Precaution for Work
INFOID:0000000003396987
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and keep them.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After re-installation is completed, be sure to check that each part works normally.
• Follow the steps below to clean components.
- Water soluble foul: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the
fouled area.
Then rub with a soft and dry cloth.
- Oily foul: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe
the fouled area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub with
a soft and dry cloth.
• Never use organic solvent such as thinner, benzene, alcohol, and gasoline.
• For genuine leather seats, use a genuine leather seat cleaner.
Revision: 2008 October
2009 Murano
SE-98
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000003396988
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000003396989
Tool number
(Kent-Moore No.)
Tool name
Description
(J39570)
Chassis ear
Locates the noise
(J43980)
NISSAN Squeak and Rattle
Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes the clips, pawls and metal clips
Hook and pick tool
Removes the snap pins
SIIA0995E
JMKIA3050ZZ
JMJIA0490ZZ
Revision: 2008 October
2009 Murano
FRONT SEAT
SE-99
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
ON-VEHICLE REPAIR
FRONT SEAT
Exploded View
INFOID:0000000003396990
DRIVER'S POWER SEAT
JMJIA1418GB
Revision: 2008 October
2009 Murano
SE-100
< ON-VEHICLE REPAIR >
FRONT SEAT
DRIVER'S MANUAL SEAT
1.
Headrest
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Seatback trim
5.
Seatback pad
6.
Seatback frame
7.
Seat cushion trim
8.
Seat cushion pad
9.
Seat cushion inner finisher outside
10. Seat cushion inner finisher inside
(right)
11.
Seat slide inner cover
12. Seat belt buckle
13. Front inner slide cover
14. Front outer slide cover
15. Seat harness
16. Seat control unit
17. Seat cushion front finisher
18. Seat reclining switch knob
19. Seat control switch knob
20. Seat cushion outer finisher outside
21. Seat cushion outer finisher inside
(left)
22. Lumbar support switch
23. Seat control switch
24. Seat slide outer cover
25. Rear outer slide cover
26. Rear inner slide cover
27. Seat cushion frame
28. Side air bag module cover
29. Side air bag module
30. Side air bag module mounting brack-
et
31. Seatback board
32. Seatback silencer
Refer to
for symbols in the figure.
Revision: 2008 October
2009 Murano
FRONT SEAT
SE-101
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
1.
Headrest
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Seatback trim
5.
Seatback pad
6.
Seatback frame
7.
Lumbar support lever
8.
Seat cushion inner finisher outside
9.
Seat cushion inner finisher inside
(right)
10. Seat slide inner cover
11.
Seat cushion trim
12. Seat cushion pad
13. Seat belt buckle
14. Seat cushion frame
15. Front inner slide cover
JMJIA1416GB
Revision: 2008 October
2009 Murano
SE-102
< ON-VEHICLE REPAIR >
FRONT SEAT
PASSENGER'S POWER SEAT
CAUTION:
Never disassembly the component parts of only front passenger seat in the dotted lines shown in the
figure below. (With occupant classification system control unit model)
16. Front outer slide cover
17. Lifter lever knob finisher
18. Lifter lever
19. Reclining lever
20. Seat cushion outer finisher outside
21. Seat cushion outer finisher inside
(left)
22. Seat slide outer cover
23. Rear outer slide cover
24. Rear inner slide cover
25. Side air bag module cover
26. Side air bag module
27. Side air bag module mounting brack-
et
28. Seatback board
29. Seatback silencer
Refer to
for symbols in the figure.
Revision: 2008 October
2009 Murano
FRONT SEAT
SE-103
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
1.
Headrest
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Seatback board
5.
Side air bag module mounting brack-
et
6.
Side air bag module
7.
Side air bag module cover
8.
Rear outer slide cover
9.
Rear inner slide cover
10. Seat cushion outer finisher outside
11.
Seat cushion outer finisher inside
(right)
12. Seat reclining switch knob
13. Seat control switch knob
14. Seat control switch
15. Seat harness
JMJIA1417GB
Revision: 2008 October
2009 Murano
SE-104
< ON-VEHICLE REPAIR >
FRONT SEAT
PASSENGER'S MANUAL SEAT
CAUTION:
Never disassembly the component parts of only front passenger seat in the dotted lines shown in the
figure below. (With occupant classification system control unit model)
16. Front outer slide cover
17. Front inner slide cover
18. Seat cushion front finisher
19. Seat cushion inner finisher outside
20. Seat cushion inner finisher inside
(left)
21. Seat belt buckle
22. Seat cushion trim
23. Seat cushion pad
24. Seat cushion frame
25. Seatback trim
26. Seatback pad
27. Seatback silencer
28. Seatback frame
29. Seat cushion assembly
Refer to
for symbols in the figure.
Revision: 2008 October
2009 Murano
FRONT SEAT
SE-105
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
1.
Headrest
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Seatback board
5.
Side air bag module mounting brack-
et
6.
Side air bag module
7.
Side air bag module cover
8.
Rear outer slide cover
9.
Rear inner slide cover
10. Seat cushion outer finisher outside
11.
Seat cushion outer finisher inside
(right)
12. Reclining lever
13. Seat cushion frame
14. Front outer slide cover
15. Front inner slide cover
JMJIA1419GB
Revision: 2008 October
2009 Murano
SE-106
< ON-VEHICLE REPAIR >
FRONT SEAT
Removal and Installation
INFOID:0000000003396991
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1.
Remove the headrest.
2.
Remove the front slide cover.
3.
Remove the mounting bolts on the front side of the front seat.
4.
Remove the rear slide cover.
5.
Remove the mounting bolts on the rear side of the front seat.
6.
Set seatback in a standing position.
7.
Disconnect harness connector under the seat and remove harness securing clips.
CAUTION:
Before removal, turn ignition switch OFF, disconnect battery negative terminal and then wait for at
least 3 minutes.
8.
Remove seat from the vehicle.
CAUTION:
• When removing and installing, use shop cloths to protect parts from damage.
• When removing and installing, 2 workers are required so as to prevent it from dropping.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Before installation, turn ignition switch OFF, disconnect battery negative terminal and then wait for
at least 3 minutes.
• Clamp the harness in position.
NOTE:
After installing the front seat, perform additional service when removing battery negative terminal.(With auto-
matic drive positioner model) Refer to
ADP-8, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGA-
.
Disassembly and Assembly
INFOID:0000000003396992
SEATBACK
Disassembly
1.
Remove the seatback board.
• Remove the seatback board band from seat cushion bottom
side.
• Remove the seatback board mounting screws (A).
16. Seat belt buckle
17. Seat cushion inner finisher outside
18. Seat cushion inner finisher inside
(left)
19. Seat cushion trim
20. Seat cushion pad
21. Seatback trim
22. Seatback pad
23. Seatback silencer
24. Seatback frame
25. Seat cushion assembly
Refer to
for symbols in the figure.
JMJIA1420ZZ
Revision: 2008 October
2009 Murano
FRONT SEAT
SE-107
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Pull down the seatback board to release the pawls.
2.
Disconnect the harness connectors and remove the harness clamps.
• Remove the seatback trim retainer (1).
• Disconnect the seatback heater harness connector (A)
(Heater seat only), lumbar support harness connector (B)
(Driver's seat only) and reclining motor harness connector (C)
(Power seat only).
3.
Remove the side air bag module.
• Remove the seatback trim retainer.
• Remove the side air bag module cover mounting screws (A).
• Remove the side air bag module.
4.
Remove the lumbar support lever knob. (Manual lumbar support seat only.)
: Pawl
JMJIA1421ZZ
JMJIA1422ZZ
JMJIA1423ZZ
JMJIA1424ZZ
Revision: 2008 October
2009 Murano
SE-108
< ON-VEHICLE REPAIR >
FRONT SEAT
Pull snap ring (1) upward, and remove lumbar support lever
knob (2) from seatback frame with hook and pick tool.
5.
Remove the seatback trim and seatback pad.
• Remove the headrest holder.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
• Remove the seatback trim and seatback pad from the seat-
back frame.
• Remove the hog rings, and separate the seatback trim and
seatback pad.
6.
Remove the seatback silencer.
7.
Remove the seatback frame.
Remove the seatback frame mounting bolts (A).
Assembly
Assemble in the reverse order of disassembly.
CAUTION:
Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with
the pad side wire.
SEAT CUSHION
Disassembly
CAUTION:
Never disassemble front passenger seat cushion assembly.
Always replace as an assembly.
For front passenger seat service parts, refer to the service part catalogue.
1.
Remove the seatback board.
JMJIA0252ZZ
PIIB4084J
JMJIA1425ZZ
Revision: 2008 October
2009 Murano
FRONT SEAT
SE-109
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Remove the seatback board fixing band on the bottom of seat
cushion.
• Remove the seatback board mounting screws (A).
• Pull down the seatback board to release the pawls.
2.
Disconnect the harness connectors and remove the harness clamps.
• Remove the seatback trim retainer (1).
• Remove the seatback heater harness connector (A), lumbar
support harness connector (B) (Driver's power seat only) and
reclining motor harness connector (C).
JMJIA1420ZZ
: Pawl
JMJIA1421ZZ
JMJIA1422ZZ
JMJIA1423ZZ
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст