Nissan Murano Z51 (2008 year). Manual — part 118
DLK-420
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
1.
Use CONSULT-III to perform Active Test (“DOOR LOCK”).
2.
Touch “ALL LCK” or “ALL UNLK” to check that it works normally.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-420, "REAR RH : Diagnosis Procedure"
REAR RH : Diagnosis Procedure
INFOID:0000000003470147
1.
CHECK DOOR LOCK ACTUATOR SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear door lock assembly RH.
3.
Check voltage between rear door lock assembly RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear door lock assembly RH. Refer to
DLK-574, "DOOR LOCK : Removal and Installa-
.
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and rear door lock assembly RH harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-96, "Removal and Installation"
NO
>> Repair or replace harness.
(+)
(–)
Condition of door lock and
unlock switch
Voltage (V)
(Approx.)
Rear door lock assembly RH
Connector
Terminal
D105
5
Ground
Lock
0
→
Battery voltage
→
0
6
Unlock
0
→
Battery voltage
→
0
BCM
Rear door lock assembly RH
Continuity
Connector
Terminal
Connector
Terminal
M119
8
D105
5
Existed
10
6
BCM
Ground
Continuity
Connector
Terminal
M119
8
Not Existed
10
Revision: 2008 October
2009 Murano
BACK DOOR OPENER ACTUATOR
DLK-421
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR OPENER ACTUATOR
Description
INFOID:0000000003470148
Back door opener actuator open back door from BCM.
Component Function Check
INFOID:0000000003470149
1.
CHECK FUNCTION
1.
Perform Active Test (“TRUNK/GLASS HATCH”) with CONSULT-III.
2.
Touch “OPEN” and check that back door opens.
Is the inspection result normal?
YES
>> Back door opener actuator is OK.
NO
>> Refer to
DLK-421, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000003470150
1.
CHECK OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect back door lock assembly.
3.
Check voltage between back door lock assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK BACK DOOR OPENER ACTUATOR CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and back door lock assembly (back door opener actu-
ator) harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-96, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK BACK DOOR OPENER ACTUATOR GROUND CIRCUIT
Check continuity between back door lock assembly harness connector and ground.
(+)
(–)
Condition of back door
opener switch
Voltage (V)
(Approx.)
Back door lock assembly
Connector
Terminal
D180
1
Ground
ON
0
→
Battery voltage
→
0
BCM
Back door lock assembly
Continuity
Connector
Terminal
Connector
Terminal
M120
23
D180
1
Existed
BCM
Ground
Continuity
Connector
Terminal
M120
23
Not existed
Back door lock assembly
Ground
Continuity
Connector
Terminal
D180
2
Existed
Revision: 2008 October
2009 Murano
DLK-422
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR OPENER ACTUATOR
Is the inspection normal?
YES
>> Replace back door lock assembly. Refer to
DLK-579, "DOOR LOCK : Removal and Installation"
NO
>> Repair or replace harness.
Revision: 2008 October
2009 Murano
KEY CYLINDER SWITCH
DLK-423
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEY CYLINDER SWITCH
Description
INFOID:0000000003719181
Power window main switch detects condition of the door key cylinder switch and transmits to BCM as the
LOCK or UNLOCK signals.
Component Function Check
INFOID:0000000003719182
1.
CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
Check (“KEY CYL LK-SW”, “KEY CYL UN-SW”) in “DATA MONITOR” mode for “POWER DOOR LOCK SYS-
TEM” with CONSULT-III. Refer to
DLK-400, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)"
.
Is the inspection result normal?
YES
>> Key cylinder switch is OK.
NO
>> Refer to
DLK-423, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000003719183
1.
CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side).
3.
Check voltage between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR KEY CYLINDER SIGNAL CIRCUIT
1.
Disconnect power window main switch connector.
2.
Check continuity between power window main switch harness connector and front door lock assembly
(driver side) harness connector.
3.
Check continuity between power window main switch connector and ground.
Monitor item
Condition
KEY CYL LK-SW
Lock
: ON
Neutral / Unlock
: OFF
KEY CYL UN-SW
Unlock
: ON
Neutral / Lock
: OFF
(+)
(–)
Voltage (V)
(Approx.)
Front door lock assembly (driver side)
Connector
Terminal
D9
5
Ground
5
6
Power window main switch
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D5
4
D9
6
Existed
6
5
Revision: 2008 October
2009 Murano
DLK-424
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
KEY CYLINDER SWITCH
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-114, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK DOOR KEY CYLINDER SWITCH GROUND CIRCUIT
Check continuity between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK DOOR KEY CYLINDER SWITCH
Check door key cylinder switch.
Refer to
DLK-424, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace front door lock assembly (driver side). Refer to
DLK-568, "DOOR LOCK : Removal and
5.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000003719184
COMPONENT INSPECTION
1.
CHECK DOOR KEY CYLINDER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) (key cylinder switch) connector.
3.
Check front door lock assembly (driver side) (key cylinder switch) terminals.
Is the inspection result normal?
YES
>> Door key cylinder switch is OK.
NO
>> Replace front door lock assembly (driver side). Refer to
DLK-329, "DOOR ASSEMBLY : Removal
.
Power window main switch
Ground
Continuity
Connector
Terminal
D5
4
Not existed
6
Front door lock assembly (driver side)
Ground
Continuity
Connector
Terminal
D9
4
Existed
Terminal
Key position
Continuity
Front door lock assembly (driver side) connector
5
4
Unlock
Existed
Neutral / Lock
Not existed
6
Lock
Existed
Neutral / Unlock
Not existed
Revision: 2008 October
2009 Murano
REMOTE KEYLESS ENTRY RECEIVER
DLK-425
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY RECEIVER
Description
INFOID:0000000003625931
Receives Intelligent Key operation and transmits to BCM.
Component Function Check
INFOID:0000000003625932
1.
CHECK FUNCTION
With CONSULT-III
Check remote keyless entry receiver (“RKE OPE COUN1”) in Data Monitor mode with CONSULT-III.
Is the inspection result normal?
YES
>> Remote keyless entry receiver is OK.
NO
>> Refer to
DLK-425, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000003625933
1.
CHECK REMOTE KEYLESS ENTRY RECEIVER OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Check signal between remote keyless entry receiver harness connector and ground with oscilloscope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 1
1.
Disconnect BCM connector and remote keyless entry receiver connector
2.
Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3.
Check continuity between BCM harness connector and ground.
Monitor item
Condition
RKE OPE COUN1
Checks whether value changes when operating Intelligent Key.
(+)
(–)
Condition
Signal
(Reference value)
Remote keyless entry receiver
Connector
Terminal
M78
2
Ground
Waiting
(All door closed)
When signal is received
(All door closed)
JMKIA0064GB
JMKIA0065GB
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M122
83
M78
2
Existed
Revision: 2008 October
2009 Murano
DLK-426
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY RECEIVER
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-96, "Removal and Installation"
NO
>> Repair or replace harness between BCM and remote keyless entry receiver.
3.
CHECK REMOTE KEYLESS ENTRY RECEIVER POWER SUPPLY
1.
Disconnect remote keyless entry receiver.
2.
Check voltage between remote keyless entry receiver harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 2
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3.
Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-96, "Removal and Installation"
NO
>> Repair or replace harness between BCM and remote keyless entry receiver.
5.
CHECK REMOTE KEYLESS ENTRY RECEIVER GROUND CIRCUIT
Check continuity between remote keyless entry receiver harness connector and ground.
Is the inspection result normal?
YES
>> Replace remote keyless entry receiver. Refer to
DLK-589, "Removal and Installation"
NO
>> GO TO 6.
6.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 3
BCM
Ground
Continuity
Connector
Terminal
M122
83
Not existed
(+)
(–)
Signal
(Reference value)
Remote keyless entry receiver
Connector
Terminal
M78
4
Ground
JMKIA0064GB
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M122
103
M78
4
Existed
BCM
Ground
Continuity
Connector
Terminal
M122
103
Not existed
Remote keyless entry receiver
Ground
Continuity
Connector
Terminal
M78
1
Existed
Revision: 2008 October
2009 Murano
REMOTE KEYLESS ENTRY RECEIVER
DLK-427
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Disconnect BCM connector.
2.
Check continuity between BCM connector and remote keyless entry receiver connector.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-96, "Removal and Installation"
NO
>> Repair or replace harness between BCM and remote keyless entry receiver.
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M123
137
M78
1
Existed
Revision: 2008 October
2009 Murano
DLK-428
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR OPENER SWITCH
BACK DOOR OPENER SWITCH
Description
INFOID:0000000003470131
Output back door open signal to BCM.
Component Function Check
INFOID:0000000003470132
1.
CHECK FUNCTION
Check back door opener switch (“TR/BD OPEN SW”) in “Data Monitor mode with CONSULT-III.
• When back door opener switch is turned to “ON”.
Is the inspection result normal?
YES
>> Back door opener switch is OK.
NO
>> Refer to
DLK-428, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000003470133
1.
CHECK BACK DOOR OPEN INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect back door opener switch connector.
3.
Check voltage between back door opener switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK BACK DOOR OPENER SWITCH CIRCUIT
1.
Disconnect BCM connector and back door opener switch assembly connector.
2.
Check continuity between BCM harness connector and back door opener switch assembly harness con-
nector.
3.
Check continuity between BCM harness connector and ground.
Monitor item
Condition
TR/BD OPEN SW
Back door opener switch is pressed: ON
Back door opener switch is released: OFF
(+)
(–)
Voltage (V)
(Approx.)
Back door opener switch assembly
Connector
Terminal
D186
1
Ground
JPMIA0011GB
BCM
Back door opener switch assembly
Continuity
Connector
Terminal
Connector
Terminal
M121
67
D186
1
Existed
BCM
Ground
Continuity
Connector
Terminal
M121
67
Not existed
Revision: 2008 October
2009 Murano
BACK DOOR OPENER SWITCH
DLK-429
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-96, "Removal and Installation"
NO
>> Repair harness or connector.
3.
CHECK BACK DOOR OPENER SWITCH GROUND CIRCUIT
Check continuity between back door opener switch assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK BACK DOOR OPENER SWITCH
DLK-429, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace back door opener switch assembly. Refer to
DLK-587, "Removal and Installation"
.
5.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000003470134
1.
CHECK BACK DOOR OPENER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect back door opener switch assembly connector.
3.
Check continuity between back door opener switch assembly terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace back door opener switch assembly. Refer to
DLK-587, "Removal and Installation"
.
Back door opener switch assembly
Ground
Continuity
Connector
Terminal
D186
2
Existed
Terminal
Condition
Continuity
Back door opener switch assembly
1
2
ON (press and hold)
Existed
OFF (release)
Not existed
Revision: 2008 October
2009 Murano
DLK-430
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
OUTSIDE WARNING BUZZER
OUTSIDE WARNING BUZZER
Description
INFOID:0000000003674396
Answers back and warns for an inappropriate operation.
Component Function Check
INFOID:0000000003674397
1.
CHECK FUNCTION
Check outside warning buzzer (“OUTSIDE BUZZER”) in Active Test mode.
Is the inspection result normal?
YES
>> Outside warning buzzer is OK.
NO
>> Refer to
DLK-430, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000003674398
1.
CHECK FUSE
1.
Turn ignition switch OFF.
2.
Check 10 A fuse, [No.6, located in fuse block (J/B)].
Is fuse fusing?
YES
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
NO
>> GO TO 2.
2.
CHECK OUTSIDE WARNING BUZZER POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect outside warning buzzer connector.
3.
Check voltage between outside warning buzzer harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace outside warning buzzer power supply circuit.
3.
CHECK OUTSIDE WARNING BUZZER CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and outside warning buzzer harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness between BCM and outside warning buzzer.
4.
CHECK OUTSIDE WARNING BUZZER
DLK-431, "Component Inspection"
.
(+)
(–)
Voltage (V)
(Approx.)
Outside warning buzzer
Connector
Terminal
E26
1
Ground
Battery voltage
BCM
Outside warning buzzer
Continuity
Connector
Terminal
Connector
Terminal
M121
64
E26
1
Existed
BCM
Ground
Continuity
Connector
Terminal
M121
64
Not existed
Revision: 2008 October
2009 Murano
OUTSIDE WARNING BUZZER
DLK-431
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace outside warning buzzer. Refer to
DLK-590, "Removal and Installation"
.
5.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000003674399
1.
CHECK OUTSIDE WARNING BUZZER
Connect battery power supply to outside warning buzzer terminals 1 and 3, and check the operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace outside warning buzzer. Refer to
DLK-374, "Removal and Installation"
.
1 (BAT+) - 3 (BAT-)
: the buzzer sounds
Revision: 2008 October
2009 Murano
DLK-432
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
KEYFOB BATTERY
KEYFOB BATTERY
Description
INFOID:0000000003625938
The following functions are available when having and carrying electronic ID.
• Door lock/unlock
• Engine start
Remote control entry function and panic alarm function are available when operating on button.
Component Function Check
INFOID:0000000003625939
1.
CHECK FUNCTION
Check remote keyless entry receiver (“RKE-LOCK”) in Data Monitor mode with CONSULT-III.
Is the inspection result normal?
YES
>> Keyfob is OK.
NO
>> Refer to
DLK-432, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000003625940
1.
CHECK KEYFOB BATTERY
Check by connecting a resistance (approximately 300
Ω
) so that the
current value becomes about 10 mA.
Is the measurement value within the specification?
YES
>> Replace keyfob.
NO
>> Replace keyfob battery. Refer to
.
Component Inspection
INFOID:0000000003625941
1.
REPLACE KEYFOB BATTERY
1.
Release the lock knob at the back of the keyfob and remove the mechanical key.
2.
Insert a flat-blade screwdriver (A) wrapped with a cloth into the
slit of the corner and twist it to separate the upper part from the
lower part.
CAUTION:
• Do not touch the circuit board or battery terminal.
• The key fob is water-resistant. However, if it does get wet,
immediately wipe it dry.
3.
Replace the battery with new one.
Monitor item
Condition
RKE-LOCK
Check LOCK signal from keyfob.
Standard
: Approx. 2.5 - 3.0V
OCC0607D
PIIB6221E
Revision: 2008 October
2009 Murano
KEYFOB BATTERY
DLK-433
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4.
Align the tips of the upper and lower parts, and then push them
together until it is securely closed.
CAUTION:
• When replacing battery, keep dirt, grease, and other for-
eign materials off the electrode contact area.
• After replacing the battery, check that all keyfob functions
work normally.
Is the inspection result normal?
YES
>> keyfob is OK.
NO
>> Check remote keyless entry receiver. Refer to
Special Repair Requirement
INFOID:0000000003625942
Refer to CONSULT-III Operation Manual NATS-IVIS/NVIS.
PIIB6222E
Revision: 2008 October
2009 Murano
DLK-434
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
KEY SLOT
KEY SLOT
Description
INFOID:0000000003470154
Detect whether Intelligent Key is inserted.
Immobilizer antenna amp checks Intelligent Key transponder.
Component Function Check
INFOID:0000000003470155
1.
CHECK FUNCTION
Check key slot (“KEY SW -SLOT”) in Data Monitor mode with CONSULT-III.
Is the inspection result normal?
YES
>> Key slot is OK.
NO
>> Refer to
DLK-434, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000003470156
1.
CHECK FUSE
1.
Turn ignition switch OFF.
2.
Check 10 A fuse, [No.9, located in fuse block (J/B)].
Is fuse fusing?
YES
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
NO
>> GO TO 2.
2.
CHECK KEY SLOT POWER SUPPLY CIRCUIT
1.
Disconnect key slot connector.
2.
Check voltage between slot harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace key slot power supply circuit.
3.
CHECK KEY SLOT GROUND CIRCUIT
Check continuity between key slot harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace key slot ground circuit.
4.
CHECK KEY SLOT CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and key slot harness connector.
Monitor item
Condition
KEY SW-SLOT
Key is inserted in key slot: ON
Key is removed from key slot: OFF
(+)
(–)
Voltage (V)
(Approx.)
Key slot
Connector
Terminal
M99
1
Ground
Battery voltage
Key slot
Ground
Continuity
Connector
Terminal
M99
7
Existed
Revision: 2008 October
2009 Murano
KEY SLOT
DLK-435
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK KEY SLOT
DLK-435, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace key slot. Refer to
DLK-591, "Removal and Installation"
6.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000003470157
1.
CHECK KEY SLOT
1.
Turn ignition switch OFF.
2.
Disconnect key slot connector.
3.
Check key slot terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace key slot. Refer to
DLK-591, "Removal and Installation"
BCM
Key slot
Continuity
Connector
Terminal
Connector
Terminal
M123
121
M99
11
Existed
BCM
Ground
Continuity
Connector
Terminal
M123
121
Not existed
Key slot
Condition
Continuity
Terminal
1
11
Intelligent Key inserted
Existed
Intelligent Key removed
Not existed
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст