Nissan Murano Z51 (2008 year). Manual — part 116
DLK-388
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
POWER DOOR LOCK SYSTEM
FUNCTION DIAGNOSIS
POWER DOOR LOCK SYSTEM
System Diagram
INFOID:0000000003497498
System Description
INFOID:0000000003497499
DOOR LOCK FUNCTION
• The door lock and unlock switch (driver side) is build into power window main switch.
• The door lock and unlock switch (passenger side) is on door trim.
• Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all doors are
locked.
• Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors and
are unlocked.
Door Key Cylinder
• With the door key inserted in the door key cylinder on driver side, turning it to “LOCK”, will lock door lock
actuator of all doors.
• With the door key inserted in the door key cylinder on driver side, turning it to “UNLOCK” once unlocks the
driver side door lock actuator; turning it to “UNLOCK” again within 60 seconds after the first unlock operation
unlocks all of the other doors. (SELECTIVE UNLOCK OPERATION)
Selective unlock operation mode can be changed using “DOOR LOCK-UNLOCK SET” mode in “WORK SUP-
PORT”. Refer to
DLK-400, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)"
AUTOMATIC DOOR LOCK/UNLOCK FUNCTION (LOCK OPERATION)
The interlock door lock function is the function that locks all doors linked with the vehicle speed or shift posi-
tion. It has 2 types as follows.
Vehicle Speed Sensing Auto Door Lock*1
All doors are locked when the vehicle speed reaches 15 miles or more.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is turned ON, all
doors are closed and the vehicle speed received from the combination meter via CAN communication
becomes 24 km/h (15 miles) or more.
P Range Interlock Door Lock
All doors are locked when shifting the selector lever from the P position to any position other than P.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is in the ON posi-
tion and the shift signal received from the TCM via CAN communication is shifted from the P position to any
position other than P.
Setting change of Automatic Door Lock/Unlock Function
The lock operation setting of the automatic door lock/unlock function can be changed.
With CONSULT-III
The ON/OFF switching of the automatic door lock function and the type selection of the automatic door lock/
unlock function can be performed at the WORK SUPPORT setting of CONSULT-III.
JMKIA1991GB
Revision: 2008 October
2009 Murano
POWER DOOR LOCK SYSTEM
DLK-389
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Without CONSULT- III
The automatic door lock function ON/OFF can be switched by performing the following operation.
1.
Close all doors (door switch OFF)
2.
Turn ignition switch ON
3.
Press and hold the door lock and unlock switch for 5 seconds or more in the lock direction within 20 sec-
onds after turning the ignition switch ON.
4.
The switching is completed when the hazard warning lamp blinks.
AUTOMATIC DOOR LOCK/UNLOCK FUNCTION (UNLOCK OPERATION)
The automatic door lock/unlock function is the function that unlocks all doors linked with the key position or
shift position. It has 2 types as follows.
IGN OFF Interlock Door Unlock*1
All doors are unlocked when the power supply position is changed from ON to OFF.
BCM outputs the unlock signal to all door lock actuators when it detects that the power supply position is
changed from ignition switch ON to OFF.
P Range Interlock Door Unlock
All doors are unlocked when shifting the selector lever from any position other than the P to P position.
BCM outputs the unlock signal to all door lock actuators when it detects that the ignition switch is in the ON
position and the shift signal received from TCM via CAN communication is shifted from any position other than
the P to P position.
Setting change of Automatic Door Lock/Unlock Function
The unlock operation setting of the automatic door lock/unlock function can be changed.
With CONSULT- III
The ON/OFF switching of the automatic door lock/unlock function and the type selection of the automatic door
lock/unlock function can be performed at the WORK SUPPORT setting of CONSULT-III.
Without CONSULT- III
The automatic door lock/unlock function ON/OFF can be switched by performing the following operation.
1.
Close all doors below (door switch OFF)
2.
Turn ignition switch ON
3.
Press and hold the door lock and unlock switch for 5 seconds or more in the unlock direction within 20
seconds after turning the power supply position ON.
4.
The switching is completed when the hazard warning lamp blinks.
*1: This function is set to ON before delivery.
OFF
→
ON
: 2 blinks
ON
→
OFF
: 1 blink
OFF
→
ON
: 2 blinks
ON
→
OFF
: 1 blink
Revision: 2008 October
2009 Murano
DLK-390
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
POWER DOOR LOCK SYSTEM
Component Parts Location
INFOID:0000000003497500
Component Description
INFOID:0000000003497501
1.
BCM M118, M119, M121, M122, M123
2.
TCM F23
3.
Combination meter M34
4.
Key slot M99
5.
Front door lock assembly (driver side)
(door key cylinder switch) D9
6.
Power window main switch
(door lock and unlock switch) D5,
D6
7.
Front power window switch (passenger
side)
(door lock and unlock switch) D45
8.
Front door switch (driver side) B34
9.
Front door lock assembly (driver
side) (door lock actuator) D9
A.
Behind the combination meter
B.
Engine room LH
C.
View with front door finisher re-
moved
JMKIA1889ZZ
Item
Function
BCM
Controls the door lock function and room lamp function.
Door lock and unlock switch
Input lock or unlock signal to BCM.
Revision: 2008 October
2009 Murano
POWER DOOR LOCK SYSTEM
DLK-391
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Door lock actuator
Output lock/unlock signal from BCM and locks/unlocks each door.
Door switch
Input door open/close condition to BCM.
Door key cylinder switch
• Input lock or unlock signal to power window main switch.
• Power window main switch transmits door lock/unlock signal to BCM.
Key slot
Input key insert/remove signal to BCM.
Combination meter
• Receive buzzer signal from BCM via CAN communication line, and sounds the buzzer.
• Transmits vehicle speed signal to CAN communication line.
TCM
Transmit shift position signal to BCM via CAN communication line.
Push-button ignition switch
Input push-button ignition switch ON/OFF condition to BCM.
Item
Function
Revision: 2008 October
2009 Murano
DLK-392
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY SYSTEM
REMOTE KEYLESS ENTRY SYSTEM
System Diagram
INFOID:0000000003443450
System Description
INFOID:0000000003443451
The remote keyless entry system can be locked and unlocked by pressing door lock and unlock button of key-
fob.
DOOR LOCK AND UNLOCK OPERATION
• When door lock and unlock button of key fob is pressed, door lock and unlock signal transmits from key fob
to BCM via remote keyless entry receiver.
• When BCM receives the door lock and unlock signal, it operates door lock actuator, flashes the hazard lamp
(lock: 2 times, unlock: 1 time) and horn chirp signal to IPDM E/R at the same time as a reminder.
• IPDM E/R honks horn (lock: 1 time) as a reminder.
OPERATION CONDITION
OPERATION AREA
To ensure that the key fob works effectively, use within 100 cm (3 ft) range of each door, however the operable
range may differ according to surroundings.
SELECTIVE UNLOCK OPERATION
When door lock is unlocked, pressing LOCK button on key fob once will lock all doors. When door lock is
locked, pressing UNLOCK button on key fob will unlock driver side door. Pressing UNLOCK button on key fob
second time within 5 seconds from the first time will unlock all doors and back door can be opened with back
door opener switch.
HAZARD AND HORN REMINDER
When the doors are locked or unlocked by key fob, power is supplied to sound horn and flash hazard warning
lamps as a reminder
The hazard and horn reminder has C mode (horn chirp mode) and S mode (non-horn chirp mode).
How to Change Hazard and Horn Reminder Modes
With CONSULT-III
Hazard reminder has modes 1, 2, 3 and 4, and horn reminder can be turned ON/OFF with any lock mode.
JMKIA1997GB
Remote controller operation
Operation condition
Lock/unlock
Key switch is OFF (keyfob is removed from key slot).
Revision: 2008 October
2009 Murano
REMOTE KEYLESS ENTRY SYSTEM
DLK-393
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Hazard and horn reminders do not operate if any door switch is ON (any door is OPEN).
Hazard reminder can be changed using “HAZARD LAMP SET” mode in “WORK SUPPORT”.
Horn reminder can be changed using “HORN CHIRP SET” mode in “WORK SUPPORT”.
Refer to
DLK-405, "MULTI REMOTE ENT : CONSULT-III Function (BCM - MULTI REMOTE ENT)"
.
Without CONSULT-III
When LOCK and UNLOCK signals are sent from the Intelligent Key for more than 2 seconds at the same time,
the hazard and horn reminder mode is changed and hazard warning lamp blinks and horn sounds as follows:
AUTO DOOR LOCK OPERATION
When all doors are locked, ignition switch is OFF (ignition switch is not pressed) and key switch is OFF (key-
fob is not inserted in key slot), doors are unlocked with keyfob button. When BCM does not receive the follow-
ing signals within 30 seconds, all doors are locked.
• Door switch is ON (door is opened)
• Door is locked
• Ignition switch is ON
• Key switch is ON (keyfob is inserted in key slot)
Auto door lock mode can be changed by “AUTO LOCK SET” mode in “WORK SUPPORT”. Refer to
"MULTI REMOTE ENT : CONSULT-III Function (BCM - MULTI REMOTE ENT)"
.
PANIC ALARM OPERATION
When key switch is OFF (when keyfob is not inserted in key slot), BCM turns on and off horn intermittently with
input of PANIC ALARM signal from key fob.
BCM outputs to IPDM E/R for panic alarm signal (horn signal) via CAN communication line.
The alarm automatically turns off after 25 seconds or when BCM receives any signal from key fob.
Panic alarm operation mode can be changed using “PANIC ALARM SET” mode in “WORK SUPPORT”.
Refer to
DLK-405, "MULTI REMOTE ENT : CONSULT-III Function (BCM - MULTI REMOTE ENT)"
.
INTERIOR LAMP TIMER OPERATION
When the following conditions occur, remote keyless entry system turns on interior lamp with input of
UNLOCK signal from key fob. For detailed description, refer to
• Interior room lamp switch is in the DOOR position
• Door switch OFF (when all the doors are closed)
DOOR LOCK OPERATION WARNING
Outside warning buzzer is sound, when key fob lock button is pressed the following either conditions.
• Any door is open
• For 3 seconds after key fob is removed from key slot
KEY FOB LOW BATTERY WARNING
Warning lamp is illuminated; when BCM is detected key fob low battery after ignition switch is turned ON.
Hazard reminder setting
Mode 1
Mode 2
Mode 3
Mode 4
Keyfob operation
Lock
Unlock
Lock
Unlock
Lock
Unlock
Lock
Unlock
Hazard warning lamp blink
—
—
—
Once
Twice
—
Twice
Once
Horn reminder setting
ON
OFF
Keyfob operation
Lock
Unlock
Lock
Unlock
Horns sound
Once
—
—
—
JMKIA2755GB
Revision: 2008 October
2009 Murano
DLK-394
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY SYSTEM
Component Parts Location
INFOID:0000000003443452
JMKIA1890ZZ
1.
BCM M118, M119, M120, M121, M122,
M123
2.
Outside warning buzzer E26
3.
IPDM E/R E10, E11
4.
Remote keyless entry receiver M78
5.
Combination meter M34
6.
Key slot M99
7.
Door switch (driver side) B34
8.
Back door lock assembly
Without automatic back door: D179
With automatic back door: D180
9.
Horn high E340, E341
10. Horn low E342, E343
11. Key fob
A.
Behind the combination meter
B.
Engine room (LH)
C.
Behind the instrument lower panel
RH
Revision: 2008 October
2009 Murano
REMOTE KEYLESS ENTRY SYSTEM
DLK-395
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Component Description
INFOID:0000000003443453
Item
Function
BCM
Controls the door lock and unlock function.
Key slot
Detects that keyfob is inserted into key slot.
Door lock actuator
Output lock / unlock signal from BCM and locks and unlocks each door.
Remote keyless entry receiver
Receives lock/unlock signal from the key fob, and then transmits to BCM.
Key fob
Transmits button operation to remote keyless entry receiver.
Revision: 2008 October
2009 Murano
DLK-396
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR OPENER SYSTEM
BACK DOOR OPENER SYSTEM
System Diagram
INFOID:0000000003443458
BACK DOOR OPENER OPERATION
System Description
INFOID:0000000003443459
BACK DOOR OPENER OPERATION
When back door opener switch is pressed, BCM opens back door opener actuator.
NOTE:
Back door opener actuator is not for locking the back door. The function is only to open the back door.
OPERATION CONDITION
If the following conditions are satisfied, back door opener operation is performed.
JMKIA1367GB
Operation
Operation condition
Back door open
• All door is unlocked
• Vehicle speed is less than 5 km/h (3 MPH).
Revision: 2008 October
2009 Murano
BACK DOOR OPENER SYSTEM
DLK-397
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Component Parts Location
INFOID:0000000003443460
Component Description
INFOID:0000000003443461
JMKIA1436ZZ
1.
BCM M118, M119, M120, M121, M122
2.
Back door lock assembly (opener actua-
tor) D180
3.
Back door opener switch assembly
(opener switch) D186
4.
Combination meter M34
A.
Behind the center console
Item
Function
BCM
Controls the back door opener function
Back door opener switch
Input back door opener switch operation signal to BCM
Back door lock assembly (Back door
opener actuator)
Opens the back door with the back door open signal from BCM
Combination meter
Transmits vehicle speed signal to BCM via CAN communication
Revision: 2008 October
2009 Murano
DLK-398
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
INTEGRATED HOMELINK TRANSMITTER
INTEGRATED HOMELINK TRANSMITTER
Component Description
INFOID:0000000003497502
Item
Function
Homelink universal transceiver
A maximum of 3 radio signals can be stored and transmitted to operate the garage door, etc.
Revision: 2008 October
2009 Murano
DIAGNOSIS SYSTEM (BCM)
DLK-399
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000003554297
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
• *1: At models with Intelligent Key system this item is displayed, but is not used.
• *2: At models with rain sensor this mode is displayed, but is not used.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT*
1
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
*
2
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
—
AIR CONDITONER*
3
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door opener system
TRUNK
×
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
TPMS (AIR PRESSURE MONITOR)
×
×
×
Revision: 2008 October
2009 Murano
DLK-400
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
• *3: This item is displayed, but is not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT-III.
DOOR LOCK
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)
INFOID:0000000003554298
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “LOCK”)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “OFF”.)
LOCK>ACC
While turning power supply position from “LOCK” to “ACC”
ACC>ON
While turning power supply position from “ACC” to “IGN”
RUN>ACC
While turning power supply position from “RUN” to “ACC” (Vehicle
is stopping and selector lever is except P position.)
CRANK>RUN
While turning power supply position from “CRANKING” to “RUN”
(From cranking up the engine to run it)
RUN>URGENT
While turning power supply position from “RUN“ to “ACC” (Emer-
gency stop operation)
ACC>OFF
While turning power supply position from “ACC” to “OFF”
OFF>LOCK
While turning power supply position from “OFF” to “LOCK”
OFF>ACC
While turning power supply position from “OFF” to “ACC”
ON>CRANK
While turning power supply position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “LOCK”.) to low power consumption mode
LOCK
Power supply position is “LOCK” (Ignition switch OFF with steer-
ing is locked.)
OFF
Power supply position is “OFF” (Ignition switch OFF with steering
is unlocked.)
ACC
Power supply position is “ACC” (Ignition switch ACC)
ON
Power supply position is “IGN” (Ignition switch ON with engine
stopped)
ENGINE RUN
Power supply position is “RUN” (Ignition switch ON with engine
running)
CRANKING
Power supply position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
Revision: 2008 October
2009 Murano
DIAGNOSIS SYSTEM (BCM)
DLK-401
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
WORK SUPPORT
DATA MONITOR
ACTIVE TEST
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
Monitor item
Description
DOOR LOCK-UNLOCK SET
Selective unlock function mode can be changed to operate (WITH) or not operate (WITHOUT) with
this mode.
AUTOMATIC DOOR LOCK SE-
LECT
Automatic door lock function mode can be selected from the following in this mode.
• VH SPD: All doors are locked when vehicle speed more than 24km/h (15MPH)
• P RANGE: All doors are locked when shifting the selector lever from P position to other than the
P position
AUTOMATIC DOOR UNLOCK
SELECT
Automatic door unlock function mode can be selected from the following in the mode.
• MODE 1: All doors are unlocked when the power supply position is changed from ON to OFF
• MODE 2: All doors are unlocked when shifting the selector lever from any position other than
the P to P position
• MODE 3: Driver side door is unlocked when the power supply position is changed from ON to
OFF
• MODE 4: Driver side door is unlocked when shifting the selector lever from any position other
than the P to P position
AUTOMATIC LOCK/UNLOCK
SET
Automatic door lock/unlock function mode can be selected from the following in this mode.
• Off: non-operational
• Unlock Only: door unlock operation only
• Lock Only: door lock operation only
• Lock/Unlock: lock/unlock operation
Monitor Item
Contents
REQ SW-DR
NOTE:
This item is displayed, but cannot be monitored.
REQ SW-AS
NOTE:
This item is displayed, but cannot be monitored.
REQ SW-BD/TR
NOTE:
This item is displayed, but cannot be monitored.
DOOR SW-DR
Indicated [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS
Indicated [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR
Indicated [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicated [ON/OFF] condition of rear door switch LH.
DOOR SW-BK
Indicated [ON/OFF] condition of back door switch.
CDL LOCK SW
Indicated [ON/OFF] condition of lock signal from door lock unlock switch.
CDL UNLOCK SW
Indicated [ON/OFF] condition of unlock signal from door lock unlock switch.
KEY CYL LK-SW
Indicated [ON/OFF] condition of lock signal from door key cylinder.
KEY CYL UN-SW
Indicated [ON/OFF] condition of unlock signal from door key cylinder.
Revision: 2008 October
2009 Murano
DLK-402
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)
INFOID:0000000003705532
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
WORK SUPPORT
SELF-DIAG RESULT
DATA MONITOR
Test item
Description
DOOR LOCK
This test is able to check door lock/unlock operation.
• The all door lock actuators are locked when “LOCK” on CONSULT-III screen is touched.
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT-III screen is touched.
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT-III screen is
touched.
• The door lock actuator (passenger side) is unlocked when “AS UNLK” on CONSULT- III screen
is touched.
• The door lock actuator (other) is unlocked when “OTR ULK” on CONSULT-III screen is touched.
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
SELF-DIAG RESULTS
Displays the diagnosis results judged by BCM.
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
Monitor item
Description
REMO CONT ID CONFIR
It can be checked whether Intelligent Key ID code is registered or not in this mode.
AUTO LOCK SET
Auto door lock time can be changed in this mode.
• MODE 1: 1 minute
• MODE 2: 5 minutes
• MODE 3: 30 seconds
• MODE 4: 2 minutes
PANIC ALARM SET
Panic alarm button pressing time on Intelligent Key remote control button can be selected from the
following with this mode.
• MODE 1: 0.5 sec.
• MODE 2: Non-operation
• MODE 3: 1.5 sec.
PW DOWN SET
Unlock button pressing time on Intelligent Key button can be selected from the following with this
mode.
• MODE 1: 3 sec.
• MODE 2: Non-operation
• MODE 3: 5 sec.
TRUNK OPEN DELAY
NOTE:
This item is displayed, but cannot be supported.
SHORT CRANKING OUTPUT
Starter motor can operate during the times below.
• 70 msec
• 100 msec
• 200 msec
INSIDE ANT DIAGNOSIS
This function allows inside key antenna self-diagnosis.
Revision: 2008 October
2009 Murano
DIAGNOSIS SYSTEM (BCM)
DLK-403
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Monitor Item
Condition
REQ SW -DR
NOTE:
This item is displayed, but cannot be monitored.
REQ SW -AS
NOTE:
This item is displayed, but cannot be monitored.
REQ SW -RR
NOTE:
This item is displayed, but cannot be monitored.
REQ SW -RL
NOTE:
This item is displayed, but cannot be monitored.
REQ SW -BD/TR
NOTE:
This item is displayed, but cannot be monitored.
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
IGN RLY2 -F/B
Indicates [ON/OFF] condition of ignition relay 2.
ACC RLY-FB
NOTE:
This item is displayed, but cannot be monitored.
CLUCH SW
NOTE:
This item is displayed, but cannot be monitored.
BRAKE SW 1
Indicates [ON/OFF]*
1
condition of brake switch power supply.
BRAKE SW 2
Indicates [ON/OFF] condition of brake switch.
DETE/CANCL SW
Indicates [ON/OFF] condition of P position.
SFT PN/N SW
Indicates [ON/OFF] condition of P or N position.
S/L -LOCK
Indicates [ON/OFF] condition of steering lock unit (LOCK).
S/L -UNLOCK
Indicates [ON/OFF] condition of steering lock unit (UNLOCK).
S/L RELAY -F/B
Indicates [ON/OFF] condition of ignition switch.
UNLK SEN -DR
Indicates [ON/OFF] condition of driver door UNLOCK status.
PUSH SW -IPDM
Indicates [ON/OFF] condition of push-button ignition switch.
IGN RLY1 -F/B
Indicates [ON/OFF] condition of ignition relay 1.
DETE SW -IPDM
Indicates [ON/OFF] condition of P position.
SFT PN -IPDM
Indicates [ON/OFF] condition of P or N position.
SFT P -MET
Indicates [ON/OFF] condition of P position.
SFT N -MET
Indicates [ON/OFF] condition of N position.
ENGINE STATE
Indicates [STOP/START/CRANK/RUN] condition of engine states.
S/L LOCK-IPDM
Indicates [ON/OFF] condition of steering lock unit (LOCK).
S/L UNLK-IPDM
Indicates [ON/OFF] condition of steering lock unit (UNLOCK).
S/L RELAY-REQ
Indicates [ON/OFF] condition of steering lock relay.
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h].
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or CVT by numerical value [Km/h].
DOOR STAT-DR
Indicates [LOCK/READY/UNLOCK] condition of driver side door status.
DOOR STAT-AS
Indicates [LOCK/READY/UNLOCK] condition of passenger side door status.
ID OK FLAG
Indicates [SET/RESET] condition of key ID.
PRMT ENG STRT
Indicates [SET/RESET] condition of engine start possibility.
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored.
KEY SW -SLOT
Indicates [ON/OFF] condition of key slot.
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from keyfob.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from keyfob.
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст