Nissan Murano Z51 (2008 year). Manual — part 406
WT-90
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
C1708: [NO DATA] FL
—
—
—
×
C1709: [NO DATA] FR
—
—
—
×
C1710: [NO DATA] RR
—
—
—
×
C1711: [NO DATA] RL
—
—
—
×
C1712: [CHECKSUM ERR] FL
—
—
—
×
C1713: [CHECKSUM ERR] FR
—
—
—
×
C1714: [CHECKSUM ERR] RR
—
—
—
×
C1715: [CHECKSUM ERR] RL
—
—
—
×
C1716: [PRESSDATA ERR] FL
—
—
—
×
C1717: [PRESSDATA ERR] FR
—
—
—
×
C1718: [PRESSDATA ERR] RR
—
—
—
×
C1719: [PRESSDATA ERR] RL
—
—
—
×
C1720: [CODE ERR] FL
—
—
—
×
C1721: [CODE ERR] FR
—
—
—
×
C1722: [CODE ERR] RR
—
—
—
×
C1723: [CODE ERR] RL
—
—
—
×
C1724: [BATT VOLT LOW] FL
—
—
—
×
C1725: [BATT VOLT LOW] FR
—
—
—
×
C1726: [BATT VOLT LOW] RR
—
—
—
×
C1727: [BATT VOLT LOW] RL
—
—
—
×
C1729: VHCL SPEED SIG ERR
—
—
—
×
C1734: CONTROL UNIT
—
—
—
×
CONSULT display
Fail-safe
Freeze Frame
Data
•Vehicle Speed
•Odo/Trip Meter
•Vehicle Condi-
tion
Intelligent Key
warning lamp ON
Tire pressure
monitor warning
lamp ON
Reference
page
Revision: 2008 October
2009 Murano
TPMS
WT-91
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
SYMPTOM DIAGNOSIS
TPMS
Symptom Table
INFOID:0000000003375993
LOW TIRE PRESSURE WARNING LAMP SYMPTOM CHART
Diagnosis
Item
Symptom
(Ignition switch ON)
Low tire pressure warning lamp
Cause
Action
Low tire pres-
sure warning
lamp
Low tire pressure
warning lamp comes
on immediately and
turns off after 1 sec-
ond.
All wheel transmit-
ters are “activated”
(working).
None (system OK)
Low tire pressure
warning lamp blinks
on for 2 seconds,
then turns off for 0.2
seconds-repeats.
All wheel transmit-
ters are not activat-
ed.
Activate all wheel tire pressure
.
Low tire pressure
warning lamp blinks
1 time.
Tire pressure trans-
mitter front LH is not
activated.
Activate tire pressure transmit-
ter front LH. Refer to
.
Low tire pressure
warning lamp blinks
2 times.
Tire pressure trans-
mitter front RH is not
activated.
Activate tire pressure transmit-
.
Low tire pressure
warning lamp blinks
3 times.
Tire pressure trans-
mitter rear RH is not
activated.
Activate tire pressure transmit-
ter rear RH. Refer to
.
SEIA0592E
SEIA0593E
SEIA0594E
SEIA0595E
SEIA0596E
Revision: 2008 October
2009 Murano
WT-92
< SYMPTOM DIAGNOSIS >
TPMS
NOTE:
If more than one wheel transmitter is NOT activated, the low tire pressure warning lamp blinking patterns for those wheels will combine.
(Example: one blink/OFF/three blinks = Tire pressure transmitter rear LH and rear RH are not activated.)
Low tire pres-
sure warning
lamp
Low tire pressure
warning lamp blinks
4 times.
Tire pressure trans-
mitter rear LH is not
activated.
Activate tire pressure transmit-
ter rear LH. Refer to
.
Low tire pressure
warning lamp comes
on and does not turn
off.
Tire pressure is low.
Check tire pressure with CON-
SULT-III. Refer to
PRESSURE MONITOR :
CONSULT-III Function (BCM -
AIR PRESSURE MONITOR)"
Low tire pressure
warning lamp blinks
on for 0.5 seconds
then turns off for 0.5
seconds-repeats for
1 minute, and then
stays on.
The fuse for combi-
nation meter from
battery is pulled out.
Check the fuse for combina-
tion meter from battery. Install
or replace (if needed).
BCM connector
pulled out.
Check BCM connector. Re-
connect if needed.
Low tire pressure or
tire pressure moni-
toring system mal-
function.
• Perform CONSULT-III Self-
Diagnosis. Refer to
"AIR PRESSURE MONI-
TOR : CONSULT-III Func-
tion (BCM - AIR
PRESSURE MONITOR)"
- Perform ID Registration if
REGISTRATION PROCE-
DURE : Special Repair Re-
quirement"
Turn signal
lamp
Turn signal lamp
does not blink 2
times or buzzer does
not sound after trans-
mitter activation.
—
1.
Tool J-45295
[SST] does not
activated.
2.
Ignition OFF
during activa-
tion.
3.
Tool J-45295
[SST] not posi-
tioned correct-
ly.
4.
Transmitters
already activat-
ed.
1.
Install new battery.
2.
Check ignition is ON dur-
ing activation.
3.
Position tool correctly
during activation.
4.
Nothing.
Diagnosis
Item
Symptom
(Ignition switch ON)
Low tire pressure warning lamp
Cause
Action
SEIA0597E
SEIA0598E
SEIA0788E
Revision: 2008 October
2009 Murano
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
WT-93
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000003375994
DESCRIPTION
The low tire pressure warning lamp illuminates for approximately 1 second and then turns OFF when the igni-
tion switch is turned ON. This is to check that no abnormal condition is present in the tire pressure monitoring
system.
The lamp bulb may be burnt out or the tire pressure monitoring system may be malfunctioning if the low tire
pressure warning lamp does not illuminate when the ignition switch is turned ON.
Diagnosis Procedure
INFOID:0000000003375995
1.
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT-III
1.
On the “SELECT DIAG” mode, select the “SELF-DIAG RESULTS” screen.
2.
Check display contents in self-diagnosis results.
Is “CAN COMM CIRCUIT” displayed in the self-diagnosis display items?
YES
>> Perform trouble diagnosis for CAN communication system. Refer to
NO
>> GO TO 2.
2.
CHECK COMBINATION METER
Check combination meter function. Refer to
MWI-34, "CONSULT-III Function (METER/M&A)"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK LOW TIRE PRESSURE WARNING LAMP
1.
Turn the ignition switch OFF.
2.
Disconnect BCM harness connectors.
3.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
Does low tire pressure warning lamp turn on?
YES
>> GO TO 4.
NO
>> Check combination meter and repair or replace. Refer to
MWI-33, "Diagnosis Description"
4.
CHECK SYMPTOM
Check symptom again.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 5.
5.
CHECK BCM
Check BCM input/output signal. Refer to
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 6.
6.
CHECK BCM HARNESS CONNECTOR
Check BCM pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-96, "Removal and Installation"
NO
>> Repair or replace damaged parts.
Revision: 2008 October
2009 Murano
WT-94
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF
Description
INFOID:0000000003375996
DESCRIPTION
The tire pressure monitoring system is checked and the warning lamp is illuminated for approximately 1 sec-
ond when the ignition switch is turned ON. The low tire pressure warning lamp turns OFF after the system
check finishes.
The system may be malfunctioning if the low tire pressure warning lamp does not turn off approximately 1 sec-
ond after the ignition switch is turned ON.
Diagnosis Procedure
INFOID:0000000003375997
1.
CHECK SYSTEM FOR BCM
With CONSULT-III
1.
On “SELF-DIAG” mode, select the “SELF-DIAG RESULTS” screen.
2.
Check display contents in self-diagnosis results.
Does self-diagnostic results indicate any malfunction?
YES
>> Perform trouble diagnosis. Refer to
WT-14, "AIR PRESSURE MONITOR : CONSULT-III Function
.
NO
>> GO TO 2.
2.
CHECK ID REGISTRATION
Perform ID registration of all transmitters. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special Repair
Does low tire pressure warning lamp turn OFF?
YES
>> INSPECTION END
NO
>> GO TO 3.
3.
CHECK BCM POWER SUPPLY CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect BCM harness connector.
3.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>>
Check the following. If any items are damaged, repair or replace damaged parts.
• 40 A fusible link [No. L located in the fuse block]. Refer to
PG-102, "Fuse and Fusible Link
.
• 10 A fuse [No. 10 located in the fuse block (J/B)]. Refer to
PG-101, "Fuse, Connector and Termi-
• Harness for short or open between battery and BCM harness connector M118 terminal 1.
• Harness for short or open between battery and BCM harness connector M119 terminal 11.
• Check battery voltage.
4.
CHECK BCM GROUND CIRCUIT
1.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
BCM
—
Voltage (Approx.)
Connector
Terminal
M118
1
Ground
Battery voltage
M119
11
BCM
—
Continuity
Connector
Terminal
M119
13
Ground
Existed
Revision: 2008 October
2009 Murano
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF
WT-95
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
YES
>> GO TO 5.
NO
>> Repair or replace damaged parts.
5.
CHECK SYMPTOM
Check symptom again.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 6.
6.
CHECK BCM
Check BCM input/output signal. Refer to
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 7.
7.
CHECK BCM HARNESS CONNECTOR
Check BCM pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-96, "Removal and Installation"
NO
>> Repair or replace damaged parts.
Revision: 2008 October
2009 Murano
WT-96
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP BLINKS
LOW TIRE PRESSURE WARNING LAMP BLINKS
Description
INFOID:0000000003375998
DESCRIPTION
The low tire pressure warning lamp illuminates or blinks.
However, a check is necessary because the symptom may not be caused by a system malfunction. For exam-
ple, the transmitter may not be initialized.
NOTE:
If low tire pressure warning lamp blinks as shown in the figure, the system is normal.
Blink Mode A
• This mode shows transmitter status is in OFF- mode.
Perform transmitter wake up operation. Refer to
MITTER WAKE UP OPERATION : Special Repair Requirement"
.
Diagnosis Procedure
INFOID:0000000003375999
1.
CHECK TIRE PRESSURE WARNING CHECK SWITCH POWER SUPPLY
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check voltage between tire pressure warning check switch connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts.
2.
CHECK TIRE PRESSURE WARNING CHECK SWITCH CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect BCM harness connector.
3.
Check continuity between BCM harness connector and tire pressure warning check switch connector.
4.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
JPEIC0031GB
Tire pressure warning check switch
—
Voltage (Approx.)
Connector
Terminal
M19
1
Ground
11.8 V
BCM
Tire pressure warning check switch
Continuity
Connector
Terminal
Connector
Terminal
M123
149
M19
1
Existed
BCM
—
Continuity
Connector
Terminal
M123
149
Ground
Not existed
Revision: 2008 October
2009 Murano
LOW TIRE PRESSURE WARNING LAMP BLINKS
WT-97
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
3.
CHECK BCM
Check BCM input/output signal. Refer to
Is the inspection result normal?
YES
>> Check tire pressure warning check switch. Refer to
NO
>> Repair or replace the BCM.
Revision: 2008 October
2009 Murano
WT-98
< SYMPTOM DIAGNOSIS >
TURN SIGNAL LAMP BLINKS
TURN SIGNAL LAMP BLINKS
Description
INFOID:0000000003376000
DESCRIPTION
• The turn signal lamp blinks when the ignition switch is turned ON.
• The BCM connector or circuit may have a malfunction.
Diagnosis Procedure
INFOID:0000000003376001
1.
CHECK TIRE PRESSURE WARNING CHECK SWITCH POWER SUPPLY CIRCUIT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check voltage between tire pressure warning check switch connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts.
2.
CHECK TIRE PRESSURE WARNING CHECK SWITCH CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect BCM harness connector.
3.
Check continuity between BCM harness connector and tire pressure warning check switch connector.
4.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK SYMPTOM
Check again.
Does the turn signal lamp remain blinking?
YES
>> Check turn signal lamp operation. Refer to
EXL-49, "Component Function Check"
NO
>> INSPECTION END
Tire pressure warning check switch
—
Voltage (Approx.)
Connector
Terminal
M19
1
Ground
11.8 V
BCM
Tire pressure warning check switch
Continuity
Connector
Terminal
Connector
Terminal
Existed
M123
149
M19
1
BCM
—
Continuity
Connector
Terminal
M123
149
Ground
Not existed
Revision: 2008 October
2009 Murano
ID REGISTRATION CANNOT BE COMPLETED
WT-99
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
ID REGISTRATION CANNOT BE COMPLETED
Description
INFOID:0000000003376002
DESCRIPTION
The ID of the transmitter installed in each wheel cannot be registered in the tire pressure monitoring system.
Inspect the transmitter or the tire pressure monitoring system circuit.
Diagnosis Procedure
INFOID:0000000003376003
1.
CHECK ID REGISTRATION
1.
Perform ID registration of all transmitters. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special
2.
Drive at a speed of 40 km/h (25 MPH) or more for 10 minutes.
3.
Check all tire pressures with CONSULT-III “DATA MONITOR” within 5 minutes.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK TRANSMITTER
1.
Perform trouble diagnosis for transmitters. Refer to
2.
Perform ID registration of all transmitters. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special
Can ID registration of all transmitters be completed?
YES
>> INSPECTION END
NO
>> Replace the transmitter.
Monitored item
Condition
Display value
AIR PRESS FL
Start the engine and drive at 40 km/h (25 MPH) or more
for 10 minutes.
Approximately equal to the indication on vehicle
information display.
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Revision: 2008 October
2009 Murano
WT-100
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
Description
INFOID:0000000003376004
LOW TIRE PRESSURE WARNING LAMP BLINKS
The tire pressure monitoring system is not malfunctioning if the low
tire pressure warning lamp blinks in the pattern as shown in the fig-
ure.
The incident occurs because the transmitter of each wheel is not
wake up.
Perform transmitter wake up operation. Refer to
TER WAKE UP OPERATION : Special Repair Requirement"
JPEIC0031GB
Revision: 2008 October
2009 Murano
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
WT-101
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000003376005
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
,
.
—
—
NVH in DLN section.
NVH in DLN section.
NVH in F
AX and
FSU
sections.
NVH in RAX and
RSU sections.
Re
fe
r to
TIRES
in
thi
s
ch
art.
Refe
r to
ROAD WHEE
L i
n
t
h
is cha
rt.
NVH in F
AX,
RAX
secti
on.
NVH in BR
section.
NVH in ST section.
Possible cause and SUSPECTED PARTS
Im
p
rop
er i
n
s
ta
lla
tio
n
,
lo
os
en
es
s
Out-of
-round
un
ba
la
nc
e
In
correct tire
pressure
Un
ev
en
ti
re we
ar
Def
o
rm
at
io
n
or da
ma
ge
No
n-u
n
if
orm
ity
In
co
rrec
t ti
re
si
ze
PR
OP
EL
LE
R
S
H
A
F
T
DIFFERENTIAL
F
R
ONT
AXLE AND FRONT S
U
SPENSION
REA
R
AXLE AND REAR S
U
SPENSION
TI
RE
S
ROAD W
H
EELS
DRIV
E SHAFT
BR
AK
E
S
T
EERING
Symptom
TIRES
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
×
×
×
×
×
×
Poor quality ride
or handling
×
×
×
×
×
×
×
×
×
×
ROAD
WHEEL
Noise
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
Shimmy, Judder
×
×
×
×
×
×
×
×
×
Poor quality ride
or handling
×
×
×
×
×
×
×
Revision: 2008 October
2009 Murano
WT-102
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Service Notice or Precautions
INFOID:0000000003376006
• Low tire pressure warning lamp blinks for 1min, then turns ON when occurring any malfunction except low
tire pressure. Delete the memory with CONSULT-III, or register the ID to turn low tire pressure warning lamp
OFF. Refer to
WT-12, "AIR PRESSURE MONITOR : Diagnosis Description"
,
PROCEDURE : Special Repair Requirement"
.
• ID registration is required when replacing or rotating wheels, replacing transmitter or BCM. Refer to
• Replace grommet seal, valve core and cap of transmitter in TPMS every tire replacement by reaching wear
limit of tire. Refer to
Revision: 2008 October
2009 Murano
PREPARATION
WT-103
< PREPARATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000003376007
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000003376008
Tool number
(Kent-Moore No.)
Tool name
Description
–
(J-45295)
Transmitter activation tool
ID registration
SEIA0462E
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
Revision: 2008 October
2009 Murano
WT-104
< ON-VEHICLE MAINTENANCE >
ROAD WHEEL
ON-VEHICLE MAINTENANCE
ROAD WHEEL
Inspection
INFOID:0000000003376009
ALUMINUM WHEEL
1.
Check tires for wear and improper inflation.
2.
Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel
runout.
a.
Remove tire from aluminum wheel and mount on a tire balance machine.
b.
Set dial indicator as shown in the figure.
c.
If the lateral deflection (A) or vertical deflection (B) for radial
runout value exceeds the limit, replace aluminum wheel.
Limit
A:
Refer to
B:
Refer to
SEIA0737E
Revision: 2008 October
2009 Murano
ROAD WHEEL TIRE ASSEMBLY
WT-105
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
ON-VEHICLE REPAIR
ROAD WHEEL TIRE ASSEMBLY
Adjustment
INFOID:0000000003376010
BALANCING WHEELS (BONDING WEIGHT TYPE)
Preparation Before Adjustment
Using releasing agent, remove double-faced adhesive tape from the road wheel.
CAUTION:
• Be careful not to scratch the road wheel during removal.
• After removing double-faced adhesive tape, wipe clean traces of releasing agent from the road
wheel.
Wheel Balance Adjustment
If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting, select
and adjust a drive-in weight mode suitable for road wheels.
1.
Set road wheel on tire balance machine using the center hole as a guide. Start the tire balance machine.
2.
When inner and outer unbalance values are shown on the tire balance machine indicator, multiply outer
unbalance value by 5/3 to determine balance weight that should be used. Select the outer balance weight
with a value closest to the calculated value above and install to the designated outer position of, or at the
designated angle in relation to the road wheel.
CAUTION:
• Do not install the inner balance weight before installing the outer balance weight.
• Before installing the balance weight, be sure to clean the mating surface of the road wheel.
a.
Indicated unbalance value
×
5/3 = balance weight to be installed
Calculation example:
23 g (0.81 oz)
×
5/3 = 38.33 g (1.35 oz)
⇒
37.5 g (1.32 oz) bal-
ance weight (closer to calculated balance weight value)
NOTE:
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
36.2
⇒
35 g (1.23 oz)
36.3
⇒
37.5 g (1.32 oz)
b.
Installed balance weight in the position.
SMA054D
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст