Nissan Murano Z51 (2008 year). Manual — part 407
WT-106
< ON-VEHICLE REPAIR >
ROAD WHEEL TIRE ASSEMBLY
• When installing balance weight (1) to road wheels, set it into
the grooved area (A) on the inner wall of the road wheel as
shown in the figure so that the balance weight center (B) is
aligned with the tire balance machine indication position
(angle) (C).
CAUTION:
• Always use genuine NISSAN adhesion balance weights.
• Balance weights are non-reusable; always replace with
new ones.
• Do not install more than three sheets of balance weight.
c.
If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight sheets in line with each other as shown in
the figure.
CAUTION:
Do not install one balance weight sheet on top of another.
3.
Start the tire balance machine again.
4.
Install drive-in balance weight on inner side of road wheel in the
tire balance machine indication position (angle).
CAUTION:
Do not install more than two balance weight.
5.
Start the tire balance machine. Make sure that inner and outer
residual unbalance values are 5 g (0.17 oz) each or below.
6.
If either residual unbalance value exceeds 5 g (0.17 oz), repeat installation procedures.
TIRE ROTATION
• Follow the maintenance schedule for tire rotation service intervals.
Refer to
MA-5, "FOR NORTH AMERICA : Explanation of General
(For North America),
(For Mexico).
• When installing the wheel, tighten wheel nuts to the specified
torque.
CAUTION:
• Do not include the T-type spare tire when rotating the tires.
• When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
• Be careful not to tighten wheel nut at torque exceeding the
criteria for preventing strain of disc rotor.
• Use NISSAN genuine wheel nuts for aluminum wheels.
JPEIC0040ZZ
Limit
Dynamic (At flange):
Refer to
Static (At flange):
Refer to
PEIA0033E
Wheel nuts tighting torque:
Refer to
.
SMA829C
Revision: 2008 October
2009 Murano
ROAD WHEEL TIRE ASSEMBLY
WT-107
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
• Perform the ID registration, after tire rotation. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special
Revision: 2008 October
2009 Murano
WT-108
< ON-VEHICLE REPAIR >
TRANSMITTER
TRANSMITTER
Exploded View
INFOID:0000000003376011
Removal and Installation
INFOID:0000000003376012
REMOVAL
1.
Deflate tire. Unscrew transmitter retaining nut and allow transmitter to fall into tire.
2.
Gently bounce tire so that transmitter falls to bottom of tire.
Place on tire changing machine and break both tire beads
ensuring that the transmitter remains at the bottom of the tire.
3.
Turn tire so that valve hole is at bottom and bounce so that
transmitter (1) is near valve hole. Carefully lift tire onto turntable
and position valve hole (and transmitter) 270 degree from
mounting/dismounting head (2).
4.
Lubricate tire well and remove first side of the tire. Reach inside
the tire and remove the transmitter.
INSTALLATION
JPEIC0041GB
1.
Transmitter
2.
Grommet seal
3.
Valve nut
4.
Valve core
5.
Cap
Refer to
for symbols in figure.
SEIA0047E
JPEIC0014GB
Revision: 2008 October
2009 Murano
TRANSMITTER
WT-109
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
1.
Put first side of tire onto rim.
2.
Mount transmitter on rim and tighten nut.
CAUTION:
Speed for tightening nut should be less than 10 rpm.
3.
Place wheel on turntable of tire machine. Ensure that transmitter
(1) is 270 degree from mounting head (2) when second side of
tire is fitted.
NOTE:
Do not touch transmitter at mounting head.
4.
Lubricate tire well and fit second side of tire as normal. Ensure
that tire does not rotate relative to rim.
5.
Inflate tire and fit to appropriate wheel position.
SEIA0049E
JPEIC0014GB
Revision: 2008 October
2009 Murano
WT-110
< ON-VEHICLE REPAIR >
TIRE PRESSURE RECEIVER
TIRE PRESSURE RECEIVER
Exploded View
INFOID:0000000003537309
Removal and Installation
INFOID:0000000003537310
REMOVAL
1.
Remove the instrument lower panel LH. Refer to
2.
Disconnect tire pressure receiver (1) harness connector.
3.
Remove Tire pressure receiver mounting screw.
4.
Remove tire pressure receiver.
INSTALLATION
Install is the reverse order of removal.
JPEIC0052ZZ
1.
Tire pressure receiver
2.
Bracket
:
Vehicle front
JPEIC0042ZZ
Revision: 2008 October
2009 Murano
SERVICE DATA AND SPECIFICATIONS (SDS)
WT-111
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Road Wheel
INFOID:0000000003376013
ALUMINUM WHEEL
Wheel Nut
INFOID:0000000003646521
Tire Air Pressure
INFOID:0000000003376014
Unit: kPa (kg/cm
2
, psi)
Item
Limit
Radial runout
Lateral deflection
Less than 0.3 mm (0.012 in)
Vertical deflection
Allowable unbalance
Dynamic (At flange)
Less than 5 g (0.17 oz) (one side)
Static (At flange)
Less than 10 g (0.35 oz)
Item
Standard
Wheel nut tighting torque
108 N·m (11 kg-m, 80 ft-lb)
Item
Standard
Front
Rear
P235/65R18 104T
230 (2.3, 33)
P235/55R20 102T
230 (2.3, 33)
T165/90D18 107M
420 (4.2, 60)
Revision: 2008 October
2009 Murano
WW-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
WW
A
B
WW
N
O
P
CONTENTS
WIPER & WASHER
BASIC INSPECTION . . . . . . . . .
DIAGNOSIS AND REPAIR WORKFLOW . . ..
Work Flow . . . . . . . . . . . . . . . .....
FUNCTION DIAGNOSIS . . . . . . . ...
FRONT WIPER AND WASHER SYSTEM . . ..
WITH RAIN SENSOR . . . . . . . . . . . . ..
WITH RAIN SENSOR : System Diagram . . . . ..
WITH RAIN SENSOR : System Description . . .....
WITH RAIN SENSOR : Component Parts Loca-
tion . . . . . . . . . . . . . . . . . . ....
WITH RAIN SENSOR : Component Description . ..
WITHOUT RAIN SENSOR . . . . . . . . . . ..
WITHOUT RAIN SENSOR : System Diagram . . ..
WITHOUT RAIN SENSOR : System Description . ..
WITHOUT RAIN SENSOR : Component Parts Lo-
cation . . . . . . . . . . . . . . . . . ...
WITHOUT RAIN SENSOR :
Component Description . . . . . . . . . . ..
REAR WIPER AND WASHER SYSTEM . . ...
System Diagram . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . .
Component Parts Location . . . . . . . . . ..
Component Description . . . . . . . . . . ..
DIAGNOSIS SYSTEM (BCM) . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
WIPER . . . . . . . . . . . . . . . . . ...
WIPER : CONSULT-III Function (BCM - WIPER) .
DIAGNOSIS SYSTEM (IPDM E/R) . . . . . .
Diagnosis Description . . . . . . . . . . . .
CONSULT-III Function (IPDM E/R) . . . . . . .
COMPONENT DIAGNOSIS . . . . . . .
WIPER AND WASHER FUSE, FUSIBLE LINK
...
Description . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
POWER SUPPLY AND GROUND CIRCUIT .
BCM (BODY CONTROL MODULE) . . . . . . ..
BCM (BODY CONTROL MODULE) : Diagnosis
Procedure . . . . . . . . . . . . . . . .
IPDM E/R (INTELLIGENT POWER DISTRIBU-
TION MODULE ENGINE ROOM) . . . . . . . ..
FRONT WIPER MOTOR LO CIRCUIT . . . ..
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
FRONT WIPER MOTOR HI CIRCUIT . . . ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
FRONT WIPER AUTO STOP SIGNAL CIR-
CUIT . . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
FRONT WIPER MOTOR GROUND CIRCUIT ...
Diagnosis Procedure . . . . . . . . . . . ...
WASHER SWITCH . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . . .
RAIN SENSOR . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
Revision: 2008 October
2009 Murano
WW-2
REAR WIPER MOTOR CIRCUIT . . . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
REAR WIPER AUTO STOP SIGNAL CIRCUIT
...
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
FRONT WIPER AND WASHER SYSTEM . . .
Wiring Diagram - FRONT WIPER AND WASHER
SYSTEM - . . . . . . . . . . . . . . . ...
REAR WIPER AND WASHER SYSTEM . . ...
Wiring Diagram - REAR WIPER AND WASHER
SYSTEM - . . . . . . . . . . . . . . . ...
ECU DIAGNOSIS . . . . . . . . . .
BCM (BODY CONTROL MODULE) . . . . ..
Reference Value . . . . . . . . . . . . . .
Wiring Diagram - BCM - . . . . . . . . . . .
Fail-safe . . . . . . . . . . . . . . . . ..
DTC Inspection Priority Chart . . . . . . . ..
DTC Index . . . . . . . . . . . . . . . ..
IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM) . . . . .
Reference Value . . . . . . . . . . . . . .
Wiring Diagram - IPDM E/R - . . . . . . . . .
Fail-safe . . . . . . . . . . . . . . . . .
DTC Index . . . . . . . . . . . . . . . .
SYMPTOM DIAGNOSIS . . . . . . .
WIPER AND WASHER SYSTEM SYMPTOMS
.
WITH RAIN SENSOR . . . . . . . . . . . ...
WITH RAIN SENSOR : Symptom Table . . . .
WITHOUT RAIN SENSOR . . . . . . . . . ...
WITHOUT RAIN SENSOR : Symptom Table . .
NORMAL OPERATING CONDITION . . . ..
Description . . . . . . . . . . . . . . . .
FRONT WIPER DOES NOT OPERATE . . ..
Description . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
PRECAUTION . . . . . . . . . . .
PRECAUTIONS . . . . . . . . . . . ...
Precaution for Procedure without Cowl Top Cover .
ON-VEHICLE REPAIR . . . . . . . ..
WASHER TANK . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
WASHER PUMP . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
WASHER LEVEL SWITCH . . . . . . . ..
Removal and Installation . . . . . . . . . ...
FRONT WASHER NOZZLE AND TUBE . . ..
Exploded View . . . . . . . . . . . . . ..
Hydraulic Layout . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
Inspection and Adjustment . . . . . . . . .
FRONT WIPER ARM . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Adjustment . . . . . . . . . . . . . . .
WIPER BLADE . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
FRONT WIPER DRIVE ASSEMBLY . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Disassembly and Assembly . . . . . . . . ..
RAIN SENSOR . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
WIPER AND WASHER SWITCH . . . . . .
Exploded View . . . . . . . . . . . . . ..
REAR WIPER ARM . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Adjustment . . . . . . . . . . . . . . .
REAR WIPER MOTOR . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
REAR WASHER NOZZLE AND TUBE . . .
Hydraulic Layout . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
Inspection and Adjustment . . . . . . . . .
Revision: 2008 October
2009 Murano
DIAGNOSIS AND REPAIR WORKFLOW
WW-3
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000003307601
OVERALL SEQUENCE
DETAILED FLOW
1.
INTERVIEW FOR MALFUNCTION
Interview the symptom to the customer.
JPLIA0313GB
Revision: 2008 October
2009 Murano
WW-4
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
>> GO TO 2.
2.
SYMPTOM CHECK
Check the symptom from the customer's information.
>> GO TO 3.
3.
BASIC INSPECTION
Check the operation of each part. Check that any symptom occurs other than the interviewed symptom.
>> GO TO 4.
4.
SELF-DIAGNOSIS WITH CONSULT-III
Perform the self-diagnosis with CONSULT-III. Check that any DTC is detected.
Is any DTC detected?
YES
>> GO TO 5.
NO
>> GO TO 6.
5.
TROUBLE DIAGNOSIS BY DTC
Perform the trouble diagnosis for the detected DTC. Specify the malfunctioning part.
>> GO TO 9.
6.
FAIL-SAFE ACTIVATION CHECK
Check that the symptom is applied to the fail-safe activation.
Does the fail-safe activate?
YES
>> GO TO 7.
NO
>> GO TO 8.
7.
SYSTEM DIAGNOSIS
Perform the system diagnosis for the system that the fail-safe activates. Specify the malfunctioning part.
>> GO TO 9.
8.
SYMPTOM DIAGNOSIS
Perform the symptom diagnosis. Specify the malfunctioning part.
>> GO TO 9.
9.
MALFUNCTION PART REPAIR
Repair or replace the malfunctioning part.
>> GO TO 10.
10.
REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT-III)
Perform the self-diagnosis with CONSULT-III. Check that any DTC is not detected. Erase DTC if DTC is
detected before the repair. Check that DTC is not detected again.
Is any DTC detected?
YES
>> GO TO 5.
NO
>> GO TO 11.
11.
REPAIR CHECK (OPERATION CHECK)
Check the operation of each part.
Does it operate normally?
YES
>> INSPECTION END
NO
>> GO TO 3.
Revision: 2008 October
2009 Murano
FRONT WIPER AND WASHER SYSTEM
WW-5
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FUNCTION DIAGNOSIS
FRONT WIPER AND WASHER SYSTEM
WITH RAIN SENSOR
WITH RAIN SENSOR : System Diagram
INFOID:0000000003307602
WITH RAIN SENSOR : System Description
INFOID:0000000003307603
OUTLINE
The front wiper is controlled by each function of BCM and IPDM E/R.
Control by BCM
• Combination switch reading function
• Front wiper control function
Control by IPDM E/R
• Front wiper control function
• Relay control function
Combination meter indicates low washer fluid warning judged with the signal from the washer level switch. For
details of low washer fluid warning, refer to
MWI-26, "INFORMATION DISPLAY : System Description"
.
FRONT WIPER BASIC OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front wiper request signal to IPDM E/R with CAN communication depending on each
operating condition of the front wiper.
• IPDM E/R turns ON/OFF the integrated front wiper relay and the front wiper high relay according to the front
wiper request signal. IPDM E/R provides the power supply to operate the front wiper HI/LO operation.
FRONT WIPER LO OPERATION
• BCM transmits the front wiper request signal (LO) to IPDM E/R with CAN communication according to the
front wiper LO operating condition.
Front wiper LO operating condition
- Ignition switch ON
- Front wiper switch LO or front wiper switch MIST (while pressing)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).
FRONT WIPER HI OPERATION
• BCM transmits the front wiper request signal (HI) to IPDM E/R with CAN communication according to the
front wiper HI operating condition.
Front wiper HI operating condition
- Ignition switch ON
- Front wiper switch HI
JPLIA1630GB
Revision: 2008 October
2009 Murano
WW-6
< FUNCTION DIAGNOSIS >
FRONT WIPER AND WASHER SYSTEM
• IPDM E/R turns ON the integrated front wiper relay and the front wiper high relay according to the front wiper
request signal (HI).
FRONT WIPER AUTO OPERATION
Rain Sensing
Rain level and sensor conditions are detected by rain sensor.
• BCM transmits the vehicle conditions (vehicle speed, front wiper condition, rain sensor sensitivity setting,
etc.) to the rain sensor via the rain sensor serial link.
• Rain sensor judges a wiping speed for front wiper by rain condition and the vehicle conditions. And it trans-
mits the wiping speed request signal to the BCM via the rain sensor serial link.
Auto Wiping Operation
• BCM receives the wiping speed request signal from the rain sensor via the rain sensor serial link.
• BCM controls front wiper operation according to the wiping speed request signals. And it transmits the front
wiper request signals (LO or HI) to the IPDM E/R via CAN communication line.
Front wiper AUTO operating condition
- Ignition switch ON
- Front wiper switch INT/AUTO
NOTE:
When the front wiper switch is turned to INT/AUTO position, front wiper operates once regardless of a rainy
condition.
Rain Sensor Sensitivity Setting
BCM determines rain sensor sensitivity according to a wiper volume.
NOTE:
When the wiper volume is turned up at 1 level with front wiper AUTO operating condition, front wiper operates
once.
FRONT WIPER AUTO STOP OPERATION
• BCM stops transmitting the front wiper request signal when the front wiper switch is turned OFF.
• IPDM E/R detects the front wiper stop position signal from the front wiper motor and detects the front wiper
motor position (stop position/except stop position).
• When the front wiper request signal is stopped, IPDM E/R turns ON the front wiper relay until the front wiper
motor returns to the stop position.
Wiper volume dial position
Sensitivity
1
High sensitivity
2
3
Medium
−
high sensitivity
4
5
Low
−
medium sensitivity
6
7
Low sensitivity
JPLIA0410GB
Revision: 2008 October
2009 Murano
FRONT WIPER AND WASHER SYSTEM
WW-7
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
NOTE:
• BCM stops the transmitting of the front wiper request signal when the ignition switch is OFF.
• IPDM E/R turns the front wiper relay OFF when the ignition switch is OFF.
FRONT WIPER OPERATION LINKED WITH WASHER
• BCM transmits the front wiper request signal (LO) to IPDM E/R with CAN communication according to the
washer linked operating condition of the front wiper.
• BCM transmits the front wiper request signal (LO) so that the front wiper operates approximately 2 times
when the front washer switch OFF is detected.
Washer linked operating condition of front wiper
- Ignition switch ON
- Front washer switch ON (0.4 second or more)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).
• The washer pump is grounded through the combination switch with the front washer switch ON.
FAIL-SAFE FUNCTION
Front Wiper control
IPDM E/R performs the fail-safe function when the front wiper auto stop circuit is malfunctioning. Refer to
.
Rain Sensor Malfunction
• BCM judges the rain sensor serial link error by the rain sensor serial link condition and detects the rain sen-
sor malfunction by rain sensor malfunction signal.
• When BCM detects the rain sensor serial link error or the rain sensor malfunction while front wiper AUTO
operation, BCM operates a fail-safe control.
NOTE:
If rain sensor malfunction is detected when ignition switch is turned OFF
⇒
ON and front wiper switch is INT/
AUTO position, BCM operates front wiper LO.
Revision: 2008 October
2009 Murano
WW-8
< FUNCTION DIAGNOSIS >
FRONT WIPER AND WASHER SYSTEM
WITH RAIN SENSOR : Component Parts Location
INFOID:0000000003307604
WITH RAIN SENSOR : Component Description
INFOID:0000000003307605
1.
Combination switch
2.
Combination meter
3.
Rain sensor
4.
Washer pump
5.
Front wiper motor
6.
IPDM E/R
7.
BCM
A.
Wind shield upper
B.
Radiator core support (RH)
C.
Cowl top, left side of engine room
D.
Engine room (left side)
E.
Behind combination meter
JPLIA0883ZZ
Part
Description
BCM
• Judges each switch status by the combination switch reading function.
• Requests (with CAN communication) the front wiper relay and the front wiper high relay ON to
IPDM E/R.
IPDM E/R
• Controls the integrated relay according to the request (with CAN communication) from BCM.
• Performs the auto stop control of the front wiper.
Revision: 2008 October
2009 Murano
FRONT WIPER AND WASHER SYSTEM
WW-9
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WITHOUT RAIN SENSOR
WITHOUT RAIN SENSOR : System Diagram
INFOID:0000000003514393
WITHOUT RAIN SENSOR : System Description
INFOID:0000000003514394
OUTLINE
The front wiper is controlled by each function of BCM and IPDM E/R.
Control by BCM
• Combination switch reading function
• Front wiper control function
Control by IPDM E/R
• Front wiper control function
• Relay control function
Combination meter indicates low washer fluid warning judged with the signal from the washer level switch. For
details of low washer fluid warning, refer to
MWI-26, "INFORMATION DISPLAY : System Description"
.
FRONT WIPER BASIC OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front wiper request signal to IPDM E/R with CAN communication depending on each
operating condition of the front wiper.
• IPDM E/R turns ON/OFF the integrated front wiper relay and the front wiper high relay according to the front
wiper request signal. IPDM E/R provides the power supply to operate the front wiper HI/LO operation.
FRONT WIPER LO OPERATION
• BCM transmits the front wiper request signal (LO) to IPDM E/R with CAN communication according to the
front wiper LO operating condition.
Front wiper LO operating condition
- Ignition switch ON
- Front wiper switch LO or front wiper switch MIST (while pressing)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).
FRONT WIPER HI OPERATION
• BCM transmits the front wiper request signal (HI) to IPDM E/R with CAN communication according to the
front wiper HI operating condition.
Combination switch
(Wiper & washer switch)
Refer to
Combination meter
Transmits the vehicle speed signal to BCM with CAN communication.
Rain sensor
Detects water droplets on the windshield with infrared rays, and transmits the rain sensor signal
to BCM through the rain sensor serial link.
Part
Description
JPLIA1261GB
Revision: 2008 October
2009 Murano
WW-10
< FUNCTION DIAGNOSIS >
FRONT WIPER AND WASHER SYSTEM
Front wiper HI operating condition
- Ignition switch ON
- Front wiper switch HI
• IPDM E/R turns ON the integrated front wiper relay and the front wiper high relay according to the front wiper
request signal (HI).
FRONT WIPER INT OPERATION
• BCM transmits the front wiper request signal (INT) to IPDM E/R with CAN communication depending on the
front wiper INT operating condition and intermittent operation delay interval according to the wiper intermit-
tent dial position.
Front wiper INT operating condition
- Ignition switch ON
- Front wiper switch INT
• IPDM E/R turns ON the integrated front wiper relay so that the front wiper is operated only once according to
the front wiper request signal (INT).
• BCM detects stop position/except stop position of the front wiper motor according to the front wiper stop
position signal received from IPDM E/R with CAN communication.
• BCM transmits the front wiper request signal (INT) again after the intermittent operation delay interval.
NOTE:
Factory setting of the front wiper intermittent operation is the operation without vehicle speed. Front wiper
intermittent operation can be set to the operation with vehicle speed by CONSULT-III. Refer to
"WIPER : CONSULT-III Function (BCM - WIPER)"
Front wiper intermittent operation with vehicle speed
• BCM calculates the intermittent operation delay interval from the following
- Vehicle speed signal (received from the combination meter with CAN communication)
- Wiper intermittent dial position
*: When without vehicle speed setting
FRONT WIPER AUTO STOP OPERATION
• BCM stops transmitting the front wiper request signal when the front wiper switch is turned OFF.
• IPDM E/R detects the front wiper stop position signal from the front wiper motor and detects the front wiper
motor position (stop position/except stop position).
Wiper intermittent
dial position
Intermittent
operation
interval
Intermittent operation delay Interval (s)
Vehicle speed
0 – 5 km/h
(0 – 3.1 MPH)
5 – 35 km/h
(3.1 – 21.7 MPH)
35 – 65 km/h*
(21.7 – 40.4 MPH)
65 km/h (40.4 MPH)
or more
1
Short
↑
↓
Long
0.8
0.6
0.4
0.24
2
4
3
2
1.2
3
10
7.5
5
3
4
16
12
8
4.8
5
24
18
12
7.2
6
32
24
16
9.6
7
42
31.5
21
12.6
JPLIA1256GB
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст