Nissan Murano Z51 (2008 year). Manual — part 125
DLK-532
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Diagnostic Worksheet
INFOID:0000000003731323
PIIB8740E
Revision: 2008 October
2009 Murano
SQUEAK AND RATTLE TROUBLE DIAGNOSES
DLK-533
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
PIIB8742E
Revision: 2008 October
2009 Murano
DLK-534
< PRECAUTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003731314
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors while ignition switch is
ON or engine is running, never use air or electric power tools or strike near the sensor(s) with a hammer.
Heavy vibration may activate the sensor(s), deploy the airbag(s), possibly cause serious injury.
When using air or electric power tools or hammers, always turn OFF ignition switch, disconnect the battery,
and wait 3 minutes or more before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000003731315
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
INFOID:0000000003731316
NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.
OPERATION PROCEDURE
PIIB3706J
Revision: 2008 October
2009 Murano
PRECAUTIONS
DLK-535
< PRECAUTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4.
Perform the necessary repair operation.
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT-III.
Work
INFOID:0000000003731318
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operational.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
Revision: 2008 October
2009 Murano
DLK-536
< PREPARATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000003731319
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000003731320
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locating the noise
(J-43980)
NISSAN Squeak and Rat-
tle Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locating the noise
Remover tool
Remove the clips, pawls, and metal clips
Power tool
SIIA0995E
PIIB7923J
PIIB1407E
Revision: 2008 October
2009 Murano
HOOD
DLK-537
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
ON-VEHICLE REPAIR
HOOD
HOOD ASSEMBLY
HOOD ASSEMBLY : Exploded View
INFOID:0000000004749781
HOOD ASSEMBLY : Removal and Installation
INFOID:0000000004749782
REMOVAL
1.
Support hood lock assembly with the proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding hood open when removing hood stay.
2.
Remove the metal clip (3) located on the connection between
the hood stay (1) and the stud ball (2) (hood side), by using a
flatted-blade screwdriver (A).
3.
Disengage the stud ball from the hood stay (hood side).
1.
Hood assembly
2.
Hood front seal
3.
Hood insulator
4.
Hood stay
5.
Hood hinge
6.
Stud ball
7.
Hood bumper rubber
8.
Radiator core seal
Refer to
JMKIA1797ZZ
JMKIA2255ZZ
Revision: 2008 October
2009 Murano
DLK-538
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
HOOD
4.
Remove hood hinge mounting nuts on the hood to remove the hood assembly.
CAUTION:
Perform work with 2 workers, because of its heavy weight.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• Before installing the hood hinge, apply anticorrosive agent onto the mounting surface of the vehicle
body.
• After installing, perform hood fitting adjustment. Refer to
DLK-538, "HOOD ASSEMBLY : Adjust-
HOOD ASSEMBLY : Adjustment
INFOID:0000000004749783
1.
Hood assembly
2.
Hood bumper rubber side
3.
Hood hinge
4.
Hood lock assembly
5.
Front grille
6.
Front fender
Refer to
for symbols in the figure.
JMKIA1834GB
Revision: 2008 October
2009 Murano
HOOD
DLK-539
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Check the clearance and the surface height between hood and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm (in)
1.
Remove hood lock and adjust the height by rotating hood bumper rubber side until hood becomes 1 to1.5
mm (0.039 to 0.059 in) lower than fender.
2.
Temporarily tighten hood lock, and position by engaging it with hood striker. Check hood lock and striker
for looseness and adjust the clearance and evenness with striker to satisfy the specification.
3.
Adjust A and B shown in the figure to the following value with hood's own weight by dropping it from
approximately 200 mm (7.874 in) height or by pressing hood lightly [approximately 29 N (3.0 kg, 6.5lb)].
4.
After adjustment tighten lock bolts to the specified torque.
HOOD HINGE
Portion
Standard
Difference
(RH/LH)
Hood – Front grille
A – A
D
Clearance
3.4 – 7.4 (0.134 – 0.291)
—
E Surface height - 1.4 – 2.6 (- 0.055 – 0.102)
—
Hood – Front fender
B – B
F
Clearance
2.4 – 5.0 (0.094 – 0.197)
< 1.5 (0.059)
G Surface height - 1.3 – 1.3 (- 0.051 – 0.051)
—
C – C
H
Clearance
2.7 – 4.7 (0.106 – 0.185)
< 1.5 (0.059)
I
Surface height - 1.4 – 1.4 (- 0.055 – 0.055)
—
1.
Hood striker
2.
Primary latch
3.
Secondary striker
4.
Secondary latch
A
: 20.0 mm (0.787 in)
B
: 6.8 mm (0.268 in)
PIIB5794E
Revision: 2008 October
2009 Murano
DLK-540
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
HOOD
HOOD HINGE : Exploded View
INFOID:0000000004749784
HOOD HINGE : Removal and Installation
INFOID:0000000004749787
REMOVAL
1.
Remove hood assembly. Refer to
DLK-537, "HOOD ASSEMBLY : Removal and Installation"
2.
Remove front fender. Refer to
DLK-545, "Removal and Installation"
3.
Remove hood hinge mounting bolts, and then remove hood hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Before installation of hood hinge, apply anticorrosive agent onto the mounting surface of the vehicle
body.
• After installation, apply touch-up paint (the body color) onto the head of the hinge mounting bolts
and nuts.
• After installation, perform hood fitting adjustment. Refer to
DLK-538, "HOOD ASSEMBLY : Adjust-
HOOD STAY
1.
Hood assembly
2.
Hood front seal
3.
Hood insulator
4.
Hood stay
5.
Hood hinge
6.
Stud ball
7.
Hood bumper rubber
8.
Radiator core seal
Refer to
for symbols in the figure.
JMKIA1797ZZ
Revision: 2008 October
2009 Murano
HOOD
DLK-541
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HOOD STAY : Exploded View
INFOID:0000000004749789
HOOD STAY : Removal and Installation
INFOID:0000000004749792
REMOVAL
1.
Remove the metal clip (3) located on the connection between
the hood stay (1) and the stud ball (2) (hood side), by using a
flat-bladed screwdriver (A).
2.
Disengage the stud ball from the hood stay (hood side).
3.
Repeat the same operation to disengage the stud ball from the
hood stay (body side), then remove the hood stay.
INSTALLATION
Install in the reverse order of removal.
1.
Hood assembly
2.
Hood front seal
3.
Hood insulator
4.
Hood stay
5.
Hood hinge
6.
Stud ball
7.
Hood bumper rubber
8.
Radiator core seal
Refer to
JMKIA1797ZZ
JMKIA2255ZZ
Revision: 2008 October
2009 Murano
DLK-542
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
HOOD
HOOD STAY : Disposal
INFOID:0000000004749793
1.
Fix hood stay (1) using a vise (C).
2.
Using hacksaw (A) slowly make 2 holes in the hood stay, in
numerical order as shown in the figure.
CAUTION:
• When cutting a hole on hood stay, always cover a hack-
saw using a shop cloth (B) to avoid scattering metal frag-
ments or oil.
• Wear eye protection (safety glasses).
• Wear gloves.
JMKIA3336ZZ
A:
20 mm (0.787 in)
B:
Cut at the groove.
JMKIA3609ZZ
Revision: 2008 October
2009 Murano
RADIATOR CORE SUPPORT
DLK-543
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
RADIATOR CORE SUPPORT
Exploded View
INFOID:0000000004749794
Removal and Installation
INFOID:0000000004749795
REMOVAL
1.
Use a refrigerant collecting equipment to discharge the refrigerant. Refer to
2.
Remove front under cover. Refer to
EXT-26, "Removal and Installation"
.
3.
Drain engine coolant from radiator. Refer to
.
4.
Remove front grille. Refer to
EXT-18, "Removal and Installation"
5.
Remove front bumper fascia, energy absorber, bumper reinforcement. Refer to
.
6.
Remove air duct assembly. Refer to
.
7.
Remove hood lock. Refer to
DLK-566, "Removal and Installation"
.
8.
Remove front combination lamp (RH/LH). Refer to
EXL-174, "Removal and Installation"
(XENON TYPE)
EXL-337, "Removal and Installation"
(HALOGEN TYPE).
9.
Disconnect connector of refrigerant pressure sensor. Refer to
.
10. Remove bumper retainer assembly. Refer to
EXT-13, "Removal and Installation"
11. Remove clips, and then remove air guide center and air guide upper.
12. Disengage harness clip from air guide side (RH).
13. Disengage pawls, and then remove air guide side (RH/LH).
14. Remove condenser. Refer to
HA-49, "Removal and Installation"
.
1.
Air guide upper
2.
Air guide side (RH/LH)
3.
Radiator core support
4.
Air guide center
: Pawl
JMKIA1805ZZ
Revision: 2008 October
2009 Murano
DLK-544
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
RADIATOR CORE SUPPORT
15. Remove radiator and engine coolant reservoir tank. Refer to
CO-13, "Removal and Installation"
.
CAUTION:
Operate with two workers, because of it is heavy weight.
16. Disconnect connectors of the following parts.
• Ambient sensor. Refer to
VTL-25, "Removal and Installation"
• Cooling fan (RH/LH) and cooling fan control module. Refer to
• Crash zone sensor. Refer to
SR-15, "Removal and Installation"
17. Remove radiator upper hose from radiator core support. Refer to
18. Remove mounting bolt (A) of radiator lower hose bracket (1).
19. Remove radiator lower hose clamp (A) from radiator core sup-
port.
20. Remove power steering oil cooler pipe (1) from radiator core
support.
21. Remove power steering oil cooler pipe clips.
22. Remove all harness clips from radiator core support.
23. Remove mounting bolts, and then remove radiator core support.
CAUTION:
Never damage power steering oil cooler pipe.
24. Remove the following parts after removing radiator core support.
• Ambient sensor. Refer to
VTL-25, "Removal and Installation"
• Cooling fan (RH/LH) and cooling fan control module. Refer to
• Crash zone sensor. Refer to
SR-15, "Removal and Installation"
INSTALLATION
Install in the reverse order of removal.
: Vehicle front
JMKIA1915ZZ
: Clip
JMKIA1916ZZ
Revision: 2008 October
2009 Murano
FRONT FENDER
DLK-545
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT FENDER
Exploded View
INFOID:0000000004749796
Removal and Installation
INFOID:0000000004749797
CAUTION:
Use a shop cloth to protect the body from being damaged during removal and installation.
REMOVAL
1.
Remove clips and remove front fender seal (front/rear).
2.
Remove front grille. Refer to
EXT-18, "Removal and Installation"
3.
Remove front bumper fascia. Refer to
EXT-13, "Removal and Installation"
.
4.
Remove front combination lamp. Refer to
EXL-174, "Removal and Installation"
(XENON TYPE),
(HALOGEN TYPE).
5.
Remove fender protector. Refer to
EXT-23, "FENDER PROTECTOR : Removal and Installation"
1.
Front fender seal (front)
2.
Front fender seal (rear)
3.
Front fender assembly
4.
Front fender finisher
5.
Insulator
: Clip
: Pawl
JMKIA1806ZZ
Revision: 2008 October
2009 Murano
DLK-546
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT FENDER
6.
Using remover tool (A), remove front fender finisher (1).
7.
Disengage front part of windshield glass molding from front fender.
8.
Remove mounting bolts and remove front fender.
CAUTION:
An viscous urethane foam is installed on the back surface of front fender. When removing the
front fender, peel of the urethane foam bit at a time, and carefully to remove it.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• After installation, check front fender adjustment. Refer to
DLK-538, "HOOD ASSEMBLY : Adjust-
DLK-548, "DOOR ASSEMBLY : Adjustment"
.
• After installation, apply the touch-up paint (the body color) onto the head of front fender mounting
bolts.
: Clip
: Pawl
JMKIA2261ZZ
Revision: 2008 October
2009 Murano
FRONT DOOR
DLK-547
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT DOOR
DOOR ASSEMBLY
DOOR ASSEMBLY : Exploded View
INFOID:0000000004749798
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000004749799
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove mounting bolts of door check link on the vehicle.
2.
Remove front door harness grommet, and then pull out the harness from the vehicle.
3.
Disconnect front door harness connector.
4.
Remove door hinge mounting nuts (door side), and then remove door assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, perform the fitting adjustment. Refer to
DLK-548, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3688ZZ
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст