Nissan Murano Z51 (2008 year). Manual — part 126
DLK-548
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR
DOOR ASSEMBLY : Adjustment
INFOID:0000000004749800
Check the clearance and surface height between front door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Front door hinge
6.
Rear door hinge (upper)
7.
Rear door hinge (lower)
8.
Door striker
9.
TORX bolt
Refer to
for symbols in the figure.
JMKIA3687GB
Revision: 2008 October
2009 Murano
FRONT DOOR
DLK-549
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Unit : mm (in)
1.
Remove front fender. Refer to
DLK-545, "Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
3.
Adjust the surface height of front door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting bolts on body side.
6.
Raise front door at rear end to adjust clearance of the front door according to the fitting standard dimen-
sion.
7.
After adjustment tighten bolts and nuts to the specified torque.
8.
Install front fender. Refer to refer to
DLK-545, "Removal and Installation"
.
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Exploded View
INFOID:0000000004749801
Portion
Clearance
Surface height
Front fender – Front door
A – A
3.4 – 5.4 (0.134 – 0.213)
- 1.0 – 1.0 (- 0.039 – 0.039)
Front door – Rear door
B – B
3.4 – 5.4 (0.134 – 0.213)
- 1.0 – 1.0 (- 0.039 – 0.039)
Front door – Rear door
G – G
2.9 – 5.9 (0.114 – 0.237)
- 1.5 – 1.5 (- 0.059 – 0.059)
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3688ZZ
Revision: 2008 October
2009 Murano
DLK-550
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR
DOOR STRIKER : Removal and Installation
INFOID:0000000004749803
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
• After installation, be sure to perform the fitting adjustment. Refer to
DOOR HINGE
DOOR HINGE : Exploded View
INFOID:0000000004749804
DOOR HINGE : Removal and Installation
INFOID:0000000004749807
REMOVAL
1.
Remove front fender. Refer to
DLK-545, "Removal and Installation"
2.
Remove front door assembly. Refer to
DLK-547, "DOOR ASSEMBLY : Removal and Installation"
.
3.
Remove front door hinge mounting bolts, and then remove front door hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3688ZZ
Revision: 2008 October
2009 Murano
FRONT DOOR
DLK-551
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• After installation, perform the fitting adjustment. Refer to
DLK-548, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
DOOR CHECK LINK
DOOR CHECK LINK : Exploded View
INFOID:0000000004749808
DOOR CHECK LINK : Removal and Installation
INFOID:0000000004749811
REMOVAL
1.
Remove front door finisher. Refer to
INT-11, "FRONT DOOR FINISHER : Removal and Installation"
2.
Fully close the front door window.
3.
Remove front door speaker.
4.
Remove mounting bolts of door check link on the vehicle.
5.
Remove mounting bolts of door check link on door panel.
6.
Take door check link out from the hole of door panel.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check front door open/close operation after installation.
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3688ZZ
Revision: 2008 October
2009 Murano
DLK-552
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR
REAR DOOR
DOOR ASSEMBLY
DOOR ASSEMBLY : Exploded View
INFOID:0000000004749812
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000004749813
CAUTION:
• Perform work with 2 workers, because of it’s heavy weight.
• When removing and installing rear door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove mounting bolts of door check link on the vehicle.
2.
Remove rear door harness grommet, and then pull out door harness from the vehicle.
3.
Disconnect rear door harness connector.
4.
Remove door hinge mounting nuts (door side), and then remove rear door assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check rear door open/close, lock/unlock operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, perform the fitting adjustment. Refer to
DLK-553, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
1.
Rear door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Seal rubber
7.
Door check link
8.
Door hinge (lower)
9.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3686ZZ
Revision: 2008 October
2009 Murano
REAR DOOR
DLK-553
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR ASSEMBLY : Adjustment
INFOID:0000000004749814
Check the clearance and surface height between rear door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Front door hinge
6.
Rear door hinge (upper)
7.
Rear door hinge (lower)
8.
Door striker
9.
TORX bolt
for symbols in the figure.
JMKIA3687GB
Revision: 2008 October
2009 Murano
DLK-554
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR
Unit: mm (in)
1.
Remove center pillar lower garnish. Refer to
INT-19, "Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
3.
Adjust the surface height of rear door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting nuts and bolts on body side.
6.
Raise rear door at rear end to adjust clearance of rear door according to the fitting standard dimension.
7.
After adjustment tighten bolts and nuts to the specified torque.
8.
Install center pillar lower garnish. Refer to
INT-19, "Removal and Installation"
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Exploded View
INFOID:0000000004749815
DOOR STRIKER : Removal and Installation
INFOID:0000000004749817
REMOVAL
Portion
Clearance
Surface height
Front door – Rear door
B – B
3.4 – 5.4 (0.134 – 0.213)
-1.0 – 1.0 (-0.039 – 0.039)
Rear door – Body side outer
C – C
3.4 – 5.4 (0.134 – 0.213)
-1.0 – 1.0 (-0.039 – 0.039)
Front door – Rear door
G – G
2.9 – 5.9 (0.114 – 0.237)
-1.5 – 1.5 (-0.059 – 0.059)
1.
Rear door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Seal rubber
7.
Door check link
8.
Door hinge (lower)
9.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3686ZZ
Revision: 2008 October
2009 Murano
REAR DOOR
DLK-555
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Remove TORX bolts, and then remove door striker.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check rear door open/close, lock/unlock operation after installation.
• After installation, be sure to perform the fitting adjustment. Refer to
DOOR HINGE
DOOR HINGE : Exploded View
INFOID:0000000004749818
DOOR HINGE : Removal and Installation
INFOID:0000000004749821
REMOVAL
1.
Remove center pillar lower garnish. Refer to
INT-19, "Removal and Installation"
.
2.
Remove rear door assembly. Refer to
DLK-552, "DOOR ASSEMBLY : Removal and Installation"
3.
Remove rear door hinge mounting bolts and nuts (body side), and then remove door hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check rear door open/close operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• When removing and installing rear door assembly, perform the fitting adjustment. Refer to
.
• After installing, apply the touch-up paint (the body color) onto the head of door hinge mounting nuts.
1.
Rear door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Seal rubber
7.
Door check link
8.
Door hinge (lower)
9.
Door hinge (upper)
for symbols in the figure.
JMKIA3686ZZ
Revision: 2008 October
2009 Murano
DLK-556
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR
DOOR CHECK LINK
DOOR CHECK LINK : Exploded View
INFOID:0000000004749823
DOOR CHECK LINK : Removal and Installation
INFOID:0000000004749825
REMOVAL
1.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Removal and Installation"
.
2.
Fully close the rear door window.
3.
Remove rear door speaker.
4.
Remove mounting bolts of the check link on the vehicle.
5.
Remove mounting bolts of the check link on door panel.
6.
Take door check link out from the hole of door panel.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check rear door open/close operation after installation.
1.
Rear door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Seal rubber
7.
Door check link
8.
Door hinge (lower)
9.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3686ZZ
Revision: 2008 October
2009 Murano
BACK DOOR
DLK-557
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR
BACK DOOR ASSEMBLY
BACK DOOR ASSEMBLY : Exploded View
INFOID:0000000004749826
BACK DOOR ASSEMBLY : Removal and Installation
INFOID:0000000004749827
CAUTION:
Perform work with 2 workers, because of its heavy weight.
NOTE:
The back door harness constitute the back door assembly.
REMOVAL
1.
Remove back door finisher inner, back door hinge cover, back door plate. Refer to
.
1.
Back door stay
2.
Back door hinge
3.
Back door striker
4.
Bumper rubber
5.
Back door weather-strip
6.
Back door assembly
7.
Stud ball
A
: Center mark
B
: Front mark
: Vehicle front
Refer to
for symbols in the figure.
JMKIA3496ZZ
Revision: 2008 October
2009 Murano
DLK-558
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR
2.
Remove grommet, and then disconnect connector (1), and washer tube (2).
3.
Pull harness and washer tube out of back door.
4.
Support back door lock with the proper material to prevent it from falling.
5.
Remove mounting bolts of power back door drive assembly (1).
(back door side)
6.
Remove back door stay on back door side. Refer to
DLK-563, "BACK DOOR STAY : Removal and Instal-
.
7.
Remove back door hinge mounting bolts on back door and remove back door assembly.
8.
Remove the following parts after removing back door assembly.
• Bumper rubber
• Stud ball
• Back door lock assembly: Refer to
DLK-579, "DOOR LOCK : Removal and Installation"
.
• Touch sensor: Refer to
DLK-582, "TOUCH SENSOR : Removal and Installation"
• Patch: Refer to
DLK-579, "DOOR LOCK : Exploded View"
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check back door open/close, lock/unlock operation after installation.
• After installation, perform fitting adjustment. Refer to
DLK-559, "BACK DOOR ASSEMBLY : Adjust-
JMKIA1917ZZ
JMKIA1918ZZ
Revision: 2008 October
2009 Murano
BACK DOOR
DLK-559
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR ASSEMBLY : Adjustment
INFOID:0000000004749828
Check the clearance and the surface height between back door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm (in)
1.
Back door assembly
2.
Bumper rubber
3.
Back door hinge
4.
Back door striker
5.
Roof panel
6.
Body side outer
7.
Rear combination lamp
8.
Rear bumper fascia
Refer to
JMKIA1835GB
Portion
Standard
Difference
(RH/LH)
Back door – Roof
A – A
F
Clearance
5.0 – 9.0 (0.197 – 0.354)
—
G
Surface height
-1.0 – 3.0 (-0.039 – 0.118)
—
Revision: 2008 October
2009 Murano
DLK-560
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR
1.
Remove back door hinge cover. Refer to
INT-37, "Removal and Installation"
.
2.
Loosen back door hinge mounting bolts (back door side).
3.
Loosen bumper rubber.
4.
Remove luggage rear plate mask. Refer to
INT-34, "Removal and Installation"
5.
Loosen back door striker mounting bolts.
6.
Lift up back door approximately 100 – 150 mm (3.937 – 5.906 in) height then close it lightly and check that
it is engaged firmly with back door closed.
7.
Check the clearance and surface height.
8.
Finally tighten back door hinge, bumper rubber, and back door striker.
9.
Install back door hinge cover and luggage rear plate mask. Refer to
INT-37, "Removal and Installation"
and
INT-34, "Removal and Installation"
.
BACK DOOR STRIKER ADJUSTMENT
Adjust back door striker so that becomes parallel with back door lock insertion direction.
BACK DOOR STRIKER
BACK DOOR STRIKER : Exploded View
INFOID:0000000004749829
Back door – Rear fender
B – B
H
Clearance
4.0 – 8.0 (0.157 – 0.315)
—
I
Surface height
-2.0 – 2.0 (-0.079 – 0.079)
—
Back door – Rear combination
lamp
C – C
J
Clearance
4.0 – 8.0 (0.157 – 0.315)
< 2.0 (0.079)
Back door – Rear bumper fascia
D – D
K
Clearance
4.0 – 8.0 (0.157 – 0.315)
< 2.0 (0.079)
E – E
L
Clearance
5.0 – 9.0 (0.197 – 0.354)
—
Portion
Standard
Difference
(RH/LH)
1.
Back door stay
2.
Back door hinge
3.
Back door striker
4.
Bumper rubber
5.
Back door weather-strip
6.
Back door assembly
JMKIA3496ZZ
Revision: 2008 October
2009 Murano
BACK DOOR
DLK-561
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR STRIKER : Removal and Installation
INFOID:0000000004749831
REMOVAL
1.
Remove luggage rear plate. Refer to
INT-34, "Removal and Installation"
2.
Remove mounting bolts, and then remove back door striker.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check back door open/close operation after installation.
• When removing and installing back door striker, be sure to perform the fitting adjustment. Refer to
DLK-559, "BACK DOOR ASSEMBLY : Adjustment"
.
BACK DOOR HINGE
BACK DOOR HINGE : Exploded View
INFOID:0000000004749832
7.
Stud ball
A
: Center mark
B
: Front mark
: Vehicle front
Refer to
for symbols in the figure.
1.
Back door stay
2.
Back door hinge
3.
Back door striker
4.
Bumper rubber
5.
Back door weather-strip
6.
Back door assembly
7.
Stud ball
A
: Center mark
B
: Front mark
: Vehicle front
Refer to
for symbols in the figure.
JMKIA3496ZZ
Revision: 2008 October
2009 Murano
DLK-562
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR
BACK DOOR HINGE : Removal and Installation
INFOID:0000000004749835
REMOVAL
1.
Remove back door assembly. Refer to
DLK-557, "BACK DOOR ASSEMBLY : Removal and Installation"
2.
Remove luggage side finisher lower and luggage side finisher upper. Refer to
.
3.
Using a remover tool, remove headlining clip at the rear side of headlining. Refer to
(NORMAL ROOF),
INT-29, "SUNROOF : Exploded View"
(SUNROOF).
4.
Remove rear side of headlining.
5.
Remove power back door drive assembly. Refer to
DLK-580, "POWER BACK DOOR DRIVE ASSEMBLY
.
6.
Remove back door hinge mounting nuts (body side), and then remove back door hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check back door open/close operation after installation.
• Check back door hinge rotating part for poor lubrication. If necessary, apply body grease.
• When removing and installing back door assembly, perform the fitting adjustment. Refer to
"BACK DOOR ASSEMBLY : Adjustment"
.
• After installation, apply touch-up paint (the body color) onto the head of back door hinge mounting
nuts.
BACK DOOR STAY
BACK DOOR STAY : Exploded View
INFOID:0000000004749836
1.
Back door stay
2.
Back door hinge
3.
Back door striker
4.
Bumper rubber
5.
Back door weather-strip
6.
Back door assembly
7.
Stud ball
A
: Center mark
B
: Front mark
JMKIA3496ZZ
Revision: 2008 October
2009 Murano
BACK DOOR
DLK-563
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR STAY : Removal and Installation
INFOID:0000000004749839
REMOVAL
1.
Support back door assembly with the proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding back door open when removing back door
stay.
2.
Remove mounting bolts of back door stay (body side).
3.
Remove metal clip (3) located on the connection between the
back door stay (1) and the stud ball (2) (back door side), by
using a flat-bladed screwdriver (A).
4.
Disengage and remove back door stay from stud ball (back door
side).
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check back door open/close operation after installation.
BACK DOOR STAY : Disposal
INFOID:0000000004749840
1.
Fix back door stay (1) using a vise (C).
2.
Using hacksaw (A) slowly make 2 holes in the back door stay, in
numerical order as shown in the figure.
CAUTION:
• When cutting a hole on back door stay, always cover a
hacksaw using a shop cloth (B) to avoid scattering metal
fragments or oil.
• Wear eye protection (safety glasses).
• Wear gloves.
BACK DOOR WEATHER-STRIP
: Vehicle front
Refer to
for symbols in the figure.
JMKIA2255ZZ
JMKIA3336ZZ
A:
20 mm (0.787 in)
B:
Cut at the groove.
JMKIA3609ZZ
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст