Nissan Murano Z51 (2008 year). Manual — part 216
GW-18
< ON-VEHICLE REPAIR >
FRONT DOOR GLASS
4.
Operate the power window main switch to raise or lower the
door window until the glass mounting bolts can be seen.
5.
Remove the glass mounting bolts.
6.
Remove the front door mirror inner cover.
7.
Remove the front door inside seal.
8.
Hold securely the front door glass and pull it out of the sash to
remove the door glass.
NOTE:
Never raise the front glass at the top upper of the door after the
door glass is removed.
9.
Remove the front door glass run.
10. Remove the front door lower sash lower bolt, then remove the front door lower sash.
INSTALLATION
Install in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000004758262
SYSTEM INITIALIZATION
Initialize the system if any of the following work has been done.
• Electric power supply to power window switch or motor is interrupted by blown fuse or disconnecting battery
cable, etc.
• Removal and installation of the regulator assembly.
• Removal and installation of the motor from the regulator assembly.
• Removal and installation of the harness connector of the power window switch.
• Removal and installation of the door glass.
• Removal and installation of the front door glass run.
• Disconnection and connection of the minus terminal of the battery.
Initialization
Follow the steps below after installing each component to the vehicle.
1.
Disconnect the minus terminal of battery or disconnect power window switch harness connector tempo-
rarily. Then reconnect after at least 1 minute.
2.
Turn ignition switch ON.
3.
Operate power window switch to fully open the window.
4.
Draw fully the power window switch in the up direction (auto close position) and hold. Continue holding
the switch even when window is completely closed and then release after more than 3 seconds.
5.
Inspect the anti-pinch system function.
NOTE:
Initialization may be cancelled with continuous opening and closing operation. In this case, initialize the
system.
INSPECT THE FUNCTION OF THE ANTI-PINCH SYSTEM
: Bolt
JMKIA1785ZZ
JMKIA0626ZZ
Revision: 2008 October
2009 Murano
FRONT DOOR GLASS
GW-19
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
1.
Fully open the door glass.
2.
Place a wooden piece (wooden hammer handle, etc.) at near fully closed position.
3.
Perform fully closing operation with auto up switch.
• Check that the glass reverses without pinching the wooden piece, is lowered approximately 150 mm (5.906
in) or for more than 3 seconds and then stops.
• The glass should not be raised with power window main switch operated while it is reversing or lowering.
CAUTION:
• Be careful not to be pinched.
• Check that the auto up function is normal before the inspection following the system initialization.
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and guide rail
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.
Revision: 2008 October
2009 Murano
GW-20
< ON-VEHICLE REPAIR >
FRONT REGULATOR
FRONT REGULATOR
Exploded View
INFOID:0000000004781214
Removal and Installation
INFOID:0000000004758264
REMOVAL
1.
Remove the front door glass. Refer to
GW-17, "Removal and Installation"
.
2.
Disconnect the power window motor harness connector.
3.
Remove the mounting bolts, and pull out the module assembly.
4.
Disengage the harness clip from the back of the module assem-
bly, and then remove the module assembly.
INSTALLATION
Install in the reverse order of removal.
1. Front door glass run
2.
Front door glass
3.
Regulator assembly
4.
Module base
5.
Power window motor
6.
Front door inside seal
7.
Front door lower sash
8.
Front door panel
: Vehicle front
JMKIA3604ZZ
: Bolt
JMKIA1786ZZ
Revision: 2008 October
2009 Murano
FRONT REGULATOR
GW-21
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
Disassembly and Assembly
INFOID:0000000004758265
DISASSEMBLY
1.
Remove the power window motor from the module assembly.
2.
Remove the regulator assembly mounting bolts, then remove the regulator assembly from module base.
ASSEMBLY
Assemble in the reverse order of disassembly.
Inspection and Adjustment
INFOID:0000000004758266
Inspection after Removal
Check the regulator assembly for the following items. Replace or
grease it if a malfunction is detected.
• Wire wear
• Regulator deformation
The shadow area in the figure show the application points of the
multi-purpose grease.
SYSTEM INITIALIZATION
Initialize the system if any of the following work has been done.
• Electric power supply to power window switch or motor is interrupted by blown fuse or disconnecting battery
cable, etc.
• Removal and installation of the regulator assembly.
• Removal and installation of the motor from the regulator assembly.
• Removal and installation of the harness connector of the power window switch.
• Removal and installation of the door glass.
• Removal and installation of the front door glass run.
• Disconnection and connection of the minus terminal of battery.
Initialization
Follow the steps below after installing each component to the vehicle.
1.
Disconnect the minus terminal of battery or disconnect power window switch harness connector tempo-
rarily. Then reconnect after at least 1 minute.
2.
Turn ignition switch ON.
3.
Operate power window switch to fully open the window.
4.
Draw fully the power window switch in the up direction (auto close position) and hold. Continue holding
the switch even when window is completely closed and then release after more than 3 seconds.
5.
Inspect the anti-pinch system function.
NOTE:
Initialization may be cancelled with continuous opening and closing operation. In this case, initialize the
system.
INSPECT THE FUNCTION OF THE ANTI-PINCH SYSTEM
1.
Fully open the door glass.
2.
Place a wooden piece (wooden hammer handle, etc.) at near fully closed position.
3.
Perform fully closing operation with auto up switch.
• Check that the glass reverses without pinching the wooden piece, is lowered approximately 150 mm (5.906
in) or for more than 3 seconds and then stops.
• The glass should not be raised with power window main switch operated while it is reversing or lowering.
CAUTION:
• Be careful not to be pinched.
• Check that the auto up function is normal before the inspection following the system initialization.
JMKIA1787ZZ
Revision: 2008 October
2009 Murano
GW-22
< ON-VEHICLE REPAIR >
FRONT REGULATOR
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and guide rail
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.
Revision: 2008 October
2009 Murano
REAR DOOR GLASS
GW-23
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR DOOR GLASS
Exploded View
INFOID:0000000004758267
Removal and Installation
INFOID:0000000004758268
REMOVAL
1.
Remove the rear door finisher. Refer to
INT-19, "Removal and Installation"
.
2.
Disconnect the rear door speaker connector.
3.
Remove the rear door outside sash cover. Refer to
EXT-39, "Removal and Installation"
4.
Remove partially the rear door glass run.
5.
Remove the corner piece assembly fixing screws, then remove the corner piece assembly.
6.
Remove the rear door inside seal
7.
Remove the sealing screen with a cutter tool.
1.
Rear door panel
2.
Rear door glass run
3.
Rear door sash (lower)
4.
Corner piece
5.
Rear door glass
6.
Power window motor
7.
Regulator assembly
8.
Rear door inside seal
9.
Sealing screen
: Vehicle front
JMKIA3605ZZ
JMKIA0631ZZ
Revision: 2008 October
2009 Murano
GW-24
< ON-VEHICLE REPAIR >
REAR DOOR GLASS
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
8.
Operate the power window switch to raise/lower the door win-
dow until the glass mounting bolts can be seen.
9.
Remove the glass mounting bolts.
10. Remove the rear door glass from inside or outside of door panel.
11. Remove the rear door glass run and rear door sash (lower).
INSTALLATION
Install in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000004758269
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and carrier plate
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.
: Bolt
JMKIA1789ZZ
JMKIA0640ZZ
Revision: 2008 October
2009 Murano
REAR REGULATOR
GW-25
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR REGULATOR
Exploded View
INFOID:0000000004781215
Removal and Installation
INFOID:0000000004758271
REMOVAL
1.
Remove the rear door glass. Refer to
GW-23, "Removal and Installation"
2.
Disconnect the connector for the regulator assembly.
3.
Remove the regulator mounting bolts, disconnect the power win-
dow motor harness connector (A) and then remove the regulator
from the door panel.
INSTALLATION
Install in the reverse order of removal.
1.
Rear door panel
2.
Rear door glass run
3.
Rear door sash (lower)
4.
Corner piece
5.
Rear door glass
6.
Power window motor
7.
Regulator assembly
8.
Rear door inside seal
9.
Sealing screen
: Vehicle front
JMKIA3605ZZ
: Bolt
JMKIA1790ZZ
Revision: 2008 October
2009 Murano
GW-26
< ON-VEHICLE REPAIR >
REAR REGULATOR
Disassembly and Assembly
INFOID:0000000004758272
DISASSEMBLY
Remove power window motor from regulator assembly.
ASSEMBLY
Assemble in the reverse order of disassembly.
Inspection and Adjustment
INFOID:0000000004758273
Inspection after Removal
Check the regulator assembly for the following items. Replace or grease it if a malfunction is detected.
• Wire wear
• Regulator deformation
The arrows in the figure show the application points of the multi-pur-
pose grease.
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and carrier plate
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.
: Grease application point
JMKIA1791ZZ
Revision: 2008 October
2009 Murano
HA-1
VENTILATION, HEATER & AIR CONDITIONER
C
D
E
F
G
H
J
K
L
M
SECTION
HA
A
B
HA
N
O
P
CONTENTS
HEATER & AIR CONDITIONING SYSTEM
BASIC INSPECTION . . . . . . . . .
DIAGNOSIS AND REPAIR WORK FLOW . . .
Work Flow . . . . . . . . . . . . . . . .....
FUNCTION DIAGNOSIS . . . . . . . ...
REFRIGERATION SYSTEM . . . . . . . ...
System Diagram . . . . . . . . . . . . . ....
System Description . . . . . . . . . . . . ...
Component Parts Location . . . . . . . . . ....
Component Description . . . . . . . . . . .....
SYMPTOM DIAGNOSIS . . . . . . . ...
REFRIGERATION SYSTEM SYMPTOMS . . ..
Trouble Diagnosis For Unusual Pressure . . . .....
Symptom Table . . . . . . . . . . . . . .....
COMPRESSOR SYSTEM SYMPTOMS . . . .
Symptom Table . . . . . . . . . . . . . ...
PRECAUTION . . . . . . . . . . . ..
PRECAUTIONS . . . . . . . . . . . . ..
FOR USA AND CANADA . . . . . . . . . . ..
FOR MEXICO . . . . . . . . . . . . . . .
Precaution Necessary for Steering Wheel Rota-
tion after Battery Disconnect . . . . . . . . ...
Precaution for Procedure without Cowl Top Cover
Precautions For Xenon Headlamp Service . . . .
Working with HFC-134a (R-134a) . . . . . . ...
General Refrigerant Precaution . . . . . . . ..
Refrigerant Connection . . . . . . . . . . ...
Service Equipment . . . . . . . . . . . . ..
COMPRESSOR . . . . . . . . . . . . .
General Precautions . . . . . . . . . . . .
LEAK DETECTION DYE . . . . . . . . ...
General Precautions . . . . . . . . . . . .
PREPARATION . . . . . . . . . . ...
PREPARATION . . . . . . . . . . . . .
Special Service Tool . . . . . . . . . . . .
Commercial Service Tool . . . . . . . . . .
Sealant or/and Lubricant . . . . . . . . . . .
ON-VEHICLE MAINTENANCE . . . . .
LUBRICANT . . . . . . . . . . . . . ..
Maintenance of Lubricant Quantity . . . . . . ..
Lubricant Adjusting Procedure for Components
Replacement Except Compressor . . . . . . ...
Lubricant Adjusting Procedure for Compressor
Replacement . . . . . . . . . . . . . . ...
REFRIGERATION SYSTEM . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
Performance Chart . . . . . . . . . . . . ..
Refrigerant Leakages . . . . . . . . . . . ..
FLUORESCENT LEAK DETECTOR . . . .
Inspection . . . . . . . . . . . . . . . .
ELECTRICAL LEAK DETECTOR . . . . .
Inspection . . . . . . . . . . . . . . . .
ON-VEHICLE REPAIR . . . . . . . . .
REFRIGERATION SYSTEM . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Inspection After Installation . . . . . . . . . .
COMPRESSOR . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
Revision: 2008 October
2009 Murano
HA-2
LOW-PRESSURE FLEXIBLE HOSE . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
HIGH-PRESSURE FLEXIBLE HOSE . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
LOW-PRESSURE PIPE . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
HIGH-PRESSURE PIPE . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
CONDENSER PIPE ASSEMBLY . . . . . ..
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
CONDENSER . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
LIQUID TANK . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
REFRIGERANT PRESSURE SENSOR . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
EVAPORATOR PIPE ASSEMBLY . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
EVAPORATOR . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
EXPANSION VALVE . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Compressor . . . . . . . . . . . . . . .
Lubricant . . . . . . . . . . . . . . . . .
Refrigerant . . . . . . . . . . . . . . . ..
Engine Idling Speed . . . . . . . . . . . .
Belt Tension . . . . . . . . . . . . . . .
Revision: 2008 October
2009 Murano
DIAGNOSIS AND REPAIR WORK FLOW
HA-3
< BASIC INSPECTION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000003341421
OVERALL SEQUENCE
*1: Refer to
(WITHOUT 7 INCH DISPLAY) or
(WITH 7 INCH
DISPLAY).
*2: Refer to
HAC-105, "Diagnosis Chart By Symptom"
(WITHOUT 7 INCH DISPLAY) or
(WITH 7 INCH DISPLAY).
DETAILED FLOW
1.
OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
>> GO TO 2.
2.
VERIFY SYMPTOM
Verify the symptom with operational check based on the information obtained from the customer. Refer to
HAC-126, "Description & Inspection"
(WITHOUT 7 INCH DISPLAY) or
HAC-222, "Diagnosis Chart By Symp-
(WITH 7 INCH DISPLAY).
JSIIA0943GB
Revision: 2008 October
2009 Murano
HA-4
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORK FLOW
>> GO TO 3.
3.
CHECK WITH SELF-DIAGNOSIS FUNCTION OF CONSULT-III
Using CONSULT-III, perform “SELF-DIAGNOSIS RESULTS” of HVAC. Refer to
(WITHOUT 7 INCH DISPLAY) or
(WITH 7 INCH DISPLAY).
Are self-diagnosis results normal?
YES
>> GO TO 4.
NO
>> GO TO 5.
4.
NARROW DOWN THE MALFUNCTIONING PARTS BY SYMPTOM DIAGNOSIS
Perform symptom diagnosis and narrow down the malfunctioning parts. Refer to
(WITHOUT 7 INCH DISPLAY) or
HAC-222, "Diagnosis Chart By Symptom"
(WITH 7 INCH DIS-
PLAY).
>> GO TO 5.
5.
REPAIR OR REPLACE
Repair or replace malfunctioning parts.
NOTE:
If DTC is displayed, erase DTC after repairing or replacing malfunctioning parts.
>> GO TO 6.
6.
FINAL CHECK
Check that the A/C system operates normally.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 3.
Revision: 2008 October
2009 Murano
REFRIGERATION SYSTEM
HA-5
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
FUNCTION DIAGNOSIS
REFRIGERATION SYSTEM
System Diagram
INFOID:0000000003072948
System Description
INFOID:0000000003072949
REFRIGERANT CYCLE
Refrigerant Flow
The refrigerant flows from the compressor, through the condenser with a liquid tank, through the evaporator,
and then back to the compressor. The refrigerant evaporation in the evaporator is controlled by an externally
equalized expansion valve, located at dash panels.
Freeze Protection
To prevent the evaporator from freezing up, the evaporator air temperature is monitored, and the voltage sig-
nal to the A/C auto amp. turns the A/C relay OFF and stops the compressor.
REFRIGERANT SYSTEM PROTECTION
Refrigerant Pressure Sensor
The refrigerant system is protected against excessively high or low-pressures by the refrigerant pressure sen-
sor, located on the liquid tank. The refrigerant pressure sensor detects the pressure inside the refrigerant line
and sends the voltage signal to the ECM if the system pressure rises above, or falls below the specifications.
ECM turns the A/C relay OFF and stops the compressor when pressure on the high-pressure side detected by
the refrigerant pressure sensor is over approximately 3,119 kPa (31.8 kg/cm
2
, 452 psi) or below approximately
118 kPa (1.2 kg/cm
2
, 17 psi).
Pressure Relief Valve
The refrigerant system is also protected by a pressure relief valve, located in the rear head of the compressor.
The release port on the pressure relief valve automatically opens and releases refrigerant into the atmosphere
when the pressure of the refrigerant in the system increases to an unusual level [more than 3,600 kPa (36.7
kg/cm
2
, 522 psi)].
RJIA1552E
Revision: 2008 October
2009 Murano
HA-6
< FUNCTION DIAGNOSIS >
REFRIGERATION SYSTEM
Component Parts Location
INFOID:0000000003072950
1.
Compressor
2.
Condenser
3.
Liquid tank
4.
Refrigerant pressure sensor
JPIIA0550ZZ
Revision: 2008 October
2009 Murano
REFRIGERATION SYSTEM
HA-7
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
Component Description
INFOID:0000000003072951
1.
Evaporator
2.
Expansion valve
3.
Blower motor
JPIIA0551ZZ
Component
Description
Compressor
Intakes, compresses, and discharges refrigerant, to circulate refrigerant inside the refrigerant cycle.
Condenser
Cools refrigerant discharged from compressor, and transforms it to liquid refrigerant.
Liquid tank
Eliminates foreign material in refrigerant, and temporarily stores liquid refrigerant.
Refrigerant pressure sensor
Refer to
Evaporator
The mist form liquid refrigerant transforms to gas through evaporation by the air conveyed from the
blower motor. The air is cooled by the heat from evaporation.
Expansion valve
Transforms high-pressure liquid refrigerant to mist form from low-pressure liquid refrigerant by the
drawing function.
Blower motor
Takes in air from the vehicle or fresh outside air, provides it forcedly pushes it into to the air condi-
tioner, and circulates it inside the vehicle.
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст