Nissan Murano Z51 (2008 year). Manual — part 144
EC-120
< FUNCTION DIAGNOSIS >
[VQ35DE]
ON BOARD DIAGNOSTIC (OBD) SYSTEM
INT/A TEMP SE
°
C or
°
F
• The intake air temperature (determined by the
signal voltage of the intake air temperature sen-
sor) is indicated.
EVAP SYS PRES
V
• The signal voltage of EVAP control system pres-
sure sensor is displayed.
FUEL LEVEL SE
V
• The signal voltage of the fuel level sensor is dis-
played.
START SIGNAL
ON/OFF
• Indicates start signal status [ON/OFF] computed
by the ECM according to the signals of engine
speed and battery voltage.
• After starting the engine, [OFF] is dis-
played regardless of the starter sig-
nal.
CLSD THL POS
ON/OFF
• Indicates idle position [ON/OFF] computed by
ECM according to the accelerator pedal position
sensor signal.
AIR COND SIG
ON/OFF
• Indicates [ON/OFF] condition of the air condition-
er switch as determined by the air conditioner sig-
nal.
P/N POSI SW
ON/OFF
• Indicates [ON/OFF] condition from the park/neu-
tral position (PNP) signal.
PW/ST SIGNAL
ON/OFF
• [ON/OFF] condition of the power steering system
(determined by the signal voltage of the power
steering pressure sensor) is indicated.
LOAD SIGNAL
ON/OFF
• Indicates [ON/OFF] condition from the electrical
load signal.
ON: Rear window defogger switch is ON and/or
lighting switch is in 2nd position.
OFF: Both rear window defogger switch and light-
ing switch are OFF.
IGNITION SW
ON/OFF
• Indicates [ON/OFF] condition from ignition switch
signal.
HEATER FAN SW
ON/OFF
• Indicates [ON/OFF] condition from the heater fan
switch signal.
BRAKE SW
ON/OFF
• Indicates [ON/OFF] condition from the stop lamp
switch signal.
INJ PULSE-B1
msec
• Indicates the actual fuel injection pulse width
compensated by ECM according to the input sig-
nals.
• When the engine is stopped, a certain
computed value is indicated.
INJ PULSE-B2
IGN TIMING
BTDC
• Indicates the ignition timing computed by ECM
according to the input signals.
• When the engine is stopped, a certain
value is indicated.
CAL/LD VALUE
%
• “Calculated load value” indicates the value of the
current air flow divided by peak air flow.
MASS AIRFLOW
g·m/s
• Indicates the mass air flow computed by ECM ac-
cording to the signal voltage of the mass air flow
sensor.
PURG VOL C/V
%
• Indicates the EVAP canister purge volume con-
trol solenoid valve control value computed by the
ECM according to the input signals.
• The opening becomes larger as the value in-
creases.
INT/V TIM (B1)
°
CA
• Indicates [
°
CA] of intake camshaft advance an-
gle.
INT/V TIM (B2)
INT/V SOL-B1
%
• The control value of the intake valve timing con-
trol solenoid valve (determined by ECM accord-
ing to the input signals) is indicated.
• The advance angle becomes larger as the value
increases.
INT/V SOL-B2
Monitored item
Unit
Description
Remarks
Revision: 2008 October
2009 Murano
ON BOARD DIAGNOSTIC (OBD) SYSTEM
EC-121
< FUNCTION DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
VIAS S/V-1
ON/OFF
• The control condition of the VIAS control solenoid
valve 1 (determined by ECM according to the in-
put signals) is indicated.
ON: VIAS control solenoid valve 1 is operating.
OFF: VIAS control solenoid valve 1 is not operat-
ing.
VIAS S/V-2
ON/OFF
• The control condition of the VIAS control solenoid
valve 2 (determined by ECM according to the in-
put signals) is indicated.
ON: VIAS control solenoid valve 2 is operating.
OFF: VIAS control solenoid valve 2 is not operat-
ing.
AIR COND RLY
ON/OFF
• The air conditioner relay control condition (deter-
mined by ECM according to the input signals) is
indicated.
ENGINE MOUNT
IDLE/TRVL
• The control condition of the electronic controlled
engine mount (determined by ECM according to
the input signals) is indicated.
IDLE: Engine speed is below 950 rpm
TRVL: Engine speed is above 950 rpm
FUEL PUMP RLY
ON/OFF
• Indicates the fuel pump relay control condition
determined by ECM according to the input sig-
nals.
VENT CONT/V
ON/OFF
• The control condition of the EVAP canister vent
control valve (determined by ECM according to
the input signals) is indicated.
ON: Closed
OFF: Open
THRTL RELAY
ON/OFF
• Indicates the throttle control motor relay control
condition determined by the ECM according to
the input signals.
COOLING FAN
HI/MID/LOW/
OFF
• The control condition of the cooling fan (deter-
mined by ECM according to the input signals) is
indicated.
HI: High speed operation
MID: Middle speed operation
LOW: Low speed operation
OFF: Stop
HO2S2 HTR (B1)
ON/OFF
• Indicates [ON/OFF] condition of heated oxygen
sensor 2 heater determined by ECM according to
the input signals.
HO2S2 HTR (B2)
I/P PULLY SPD
rpm
• Indicates the engine speed computed from the
turbine revolution sensor signal.
VEHICLE SPEED
km/h or mph
• The vehicle speed computed from the vehicle
speed signal sent from TCM is displayed.
IDL A/V LEARN
YET/CMPLT
• Displays the condition of idle air volume learning
YET: Idle Air Volume Learning has not been per-
formed yet.
CMPLT: Idle Air Volume Learning has already
been performed successfully.
ENG OIL TEMP
°
C or
°
F
• The engine oil temperature (determined by the
signal voltage of the engine oil temperature sen-
sor) is displayed.
TRVL AFTER MIL
km or mile
• Distance traveled while MIL is activated.
A/F S1 HTR(B1)
%
• Air fuel ratio (A/F) sensor 1 heater control value
computed by ECM according to the input signals.
• The current flow to the heater becomes larger as
the value increases.
A/F S1 HTR(B2)
Monitored item
Unit
Description
Remarks
Revision: 2008 October
2009 Murano
EC-122
< FUNCTION DIAGNOSIS >
[VQ35DE]
ON BOARD DIAGNOSTIC (OBD) SYSTEM
NOTE:
AC PRESS SEN
V
• The signal voltage from the refrigerant pressure
sensor is displayed.
VHCL SPEED SE
km/h or mph
• The vehicle speed computed from the vehicle
speed signal sent from combination meter is dis-
played.
SET VHCL SPD
km/h or mph
• The preset vehicle speed is displayed.
MAIN SW
ON/OFF
• Indicates [ON/OFF] condition from MAIN switch
signal.
CANCEL SW
ON/OFF
• Indicates [ON/OFF] condition from CANCEL
switch signal.
RESUME/ACC SW
ON/OFF
• Indicates [ON/OFF] condition from RESUME/AC-
CELERATE switch signal.
SET SW
ON/OFF
• Indicates [ON/OFF] condition from SET/COAST
switch signal.
BRAKE SW1
ON/OFF
• Indicates [ON/OFF] condition from ASCD brake
switch signal or ASCD clutch switch.
BRAKE SW2
ON/OFF
• Indicates [ON/OFF] condition of stop lamp switch
signal.
VHCL SPD CUT
NON/CUT
• Indicates the vehicle cruise condition.
NON: Vehicle speed is maintained at the ASCD
set speed.
CUT: Vehicle speed decreased to excessively
low compared with the ASCD set speed, and
ASCD operation is cut off.
LO SPEED CUT
NON/CUT
• Indicates the vehicle cruise condition.
NON: Vehicle speed is maintained at the ASCD
set speed.
CUT: Vehicle speed decreased to excessively
low, and ASCD operation is cut off.
AT OD MONITOR
ON/OFF
• Indicates [ON/OFF] condition of CVT O/D ac-
cording to the input signal from the TCM.
AT OD CANCEL
ON/OFF
• Indicates [ON/OFF] condition of CVT O/D cancel
request signal.
CRUISE LAMP
ON/OFF
• Indicates [ON/OFF] condition of CRUISE lamp
determined by the ECM according to the input
signals.
SET LAMP
ON/OFF
• Indicates [ON/OFF] condition of SET lamp deter-
mined by the ECM according to the input signals.
BAT CUR SEN
mV
• The signal voltage of battery current sensor is
displayed.
ALT DUTY SIG
ON/OFF
• The control condition of the power generation
voltage variable control (determined by ECM ac-
cording to the input signals) is indicated.
ON: Power generation voltage variable control is
active.
OFF: Power generation voltage variable control
is inactive.
A/F ADJ-B1
—
• Indicates the correction of a factor stored in ECM.
The factor is calculated from the difference be-
tween the target air-fuel ratio stored in ECM and
the air-fuel ratio calculated from A/F sensor 1 sig-
nal.
A/F ADJ-B2
ALT DUTY
%
• Indicates the duty ratio of the power generation
command value. The ratio is calculated by ECM
based on the battery current sensor signal.
Monitored item
Unit
Description
Remarks
Revision: 2008 October
2009 Murano
ON BOARD DIAGNOSTIC (OBD) SYSTEM
EC-123
< FUNCTION DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Any monitored item that does not match the vehicle being diagnosed is deleted from the display automatically.
ACTIVE TEST MODE
Test Item
TEST ITEM
CONDITION
JUDGMENT
CHECK ITEM (REMEDY)
FUEL INJEC-
TION
• Engine: Return to the original
non-standard condition
• Change the amount of fuel injec-
tion using CONSULT-III.
If malfunctioning symptom disap-
pears, see CHECK ITEM.
• Harness and connectors
• Fuel injector
• Air fuel ratio (A/F) sensor 1
IGNITION TIM-
ING
• Engine: Return to the original
non-standard condition
• Timing light: Set
• Retard the ignition timing using
CONSULT-III.
If malfunctioning symptom disap-
pears, see CHECK ITEM.
• Perform Idle Air Volume Learning.
POWER BAL-
ANCE
• Engine: After warming up, idle the
engine.
• A/C switch OFF
• Selector lever: P or N position
• Cut off each injector signal one at
a time using CONSULT-III.
Engine runs rough or stops.
• Harness and connectors
• Compression
• Fuel injector
• Power transistor
• Spark plug
• Ignition coil
COOLING FAN*
• Ignition switch: ON
• Turn the cooling fan “HI”, “MID”,
“LOW” and “OFF” using CON-
SULT-III.
Cooling fan moves and stops.
• Harness and connectors
• Cooling fan motor
• IPDM E/R
ENG COOLANT
TEMP
• Engine: Return to the original
non-standard condition
• Change the engine coolant tem-
perature using CONSULT-III.
If malfunctioning symptom disap-
pears, see CHECK ITEM.
• Harness and connectors
• Engine coolant temperature sen-
sor
• Fuel injector
FUEL PUMP RE-
LAY
• Ignition switch: ON (Engine
stopped)
• Turn the fuel pump relay “ON”
and “OFF” using CONSULT-III
and listen to operating sound.
Fuel pump relay makes the operat-
ing sound.
• Harness and connectors
• Fuel pump relay
VIAS S/V-1
• Ignition switch: ON
• Turn solenoid valve “ON” and
“OFF” using CONSULT-III and lis-
ten to operating sound.
Solenoid valve makes the operating
sound.
• Harness and connectors
• Solenoid valve
VIAS S/V-2
• Ignition switch: ON
• Turn solenoid valve “ON” and
“OFF” using CONSULT-III and lis-
ten to operating sound.
Solenoid valve makes the operating
sound.
• Harness and connectors
• Solenoid valve
ENGINE
MOUNTING
• Ignition switch: ON
• Turn electronic controlled engine
mount “IDLE” and “TRVL” with
CONSULT-III.
Electronic controlled engine mount
makes the operating sound.
• Harness and connectors
• Electronic controlled engine mount
PURG VOL
CONT/V
• Engine: After warming up, run en-
gine at 1,500 rpm.
• Change the EVAP canister purge
volume control solenoid valve
opening percent using CON-
SULT-III.
Engine speed changes according to
the opening percent.
• Harness and connectors
• Solenoid valve
FUEL/T TEMP
SEN
• Change the fuel tank temperature using CONSULT-III.
VENT CON-
TROL/V
• Ignition switch: ON (Engine
stopped)
• Turn solenoid valve “ON” and
“OFF” with the CONSULT-III and
listen to operating sound.
Solenoid valve makes an operating
sound.
• Harness and connectors
• Solenoid valve
Revision: 2008 October
2009 Murano
EC-124
< FUNCTION DIAGNOSIS >
[VQ35DE]
ON BOARD DIAGNOSTIC (OBD) SYSTEM
*: Leaving cooling fan OFF with CONSULT-III while engine is running may cause the engine to overheat.
DTC & SRT CONFIRMATION MODE
SRT STATUS Mode
For details, refer to
EC-102, "Diagnosis Description"
.
SRT WORK SUPPORT Mode
This mode enables a technician to drive a vehicle to set the SRT while monitoring the SRT status.
DTC WORK SUPPORT Mode
*: DTC P1442 and P1456 does not apply to this model but appears in DTC Work Support Mode screens.
Diagnosis Tool Function
INFOID:0000000003387928
DESCRIPTION
Generic Scan Tool (OBD II scan tool) complying with SAE J1978 has
several functions explained below.
ISO15765-4 is used as the protocol.
The name “GST” or “Generic Scan Tool” is used in this service man-
ual.
FUNCTION
INT V/T ASSIGN
ANGLE
• Engine: Return to the original
non-standard condition
• Change intake valve timing using
CONSULT-III.
If malfunctioning symptom disap-
pears, see CHECK ITEM.
• Harness and connectors
• Intake valve timing control sole-
noid valve
ALTERNATOR
DUTY
• Engine: Idle
• Change duty ratio using CON-
SULT-III.
Battery voltage changes.
• Harness and connectors
• IPDM E/R
• Alternator
TEST ITEM
CONDITION
JUDGMENT
CHECK ITEM (REMEDY)
Test mode
Test item
Corresponding DTC No.
Reference page
EVAPORATIVE SYSTEM
EVP SML LEAK P0442/P1442*
P0442
P0455
EVP V/S LEAK P0456/P1456*
P0456
PURG VOL CN/V P1444
P0443
PURG FLOW P0441
P0441
A/F SEN1
A/F SEN1(B1) P1278/P1279
P0133
A/F SEN1(B1) P1276
P0130
A/F SEN1(B2) P1288/P1289
P0153
A/F SEN1(B2) P1286
P0150
HO2S2
HO2S2(B1) P1146
P0138
HO2S2(B1) P1147
P0137
HO2S2(B1) P0139
P0139
HO2S2(B2) P1166
P0158
HO2S2(B2) P1167
P0157
HO2S2(B2) P0159
P0159
SEF139P
Revision: 2008 October
2009 Murano
ON BOARD DIAGNOSTIC (OBD) SYSTEM
EC-125
< FUNCTION DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
INSPECTION PROCEDURE
1.
Turn ignition switch OFF.
2.
Connect “GST” to data link connector (2), which is located under
LH dash panel.
3.
Turn ignition switch ON.
Diagnostic Service
Function
Service $01
READINESS TESTS
This diagnostic service gains access to current emission-related data values, including an-
alog inputs and outputs, digital inputs and outputs, and system status information.
Service $02
(FREEZE DATA)
This diagnostic service gains access to emission-related data value that were stored by
ECM during the freeze frame. For details, refer to
Service $03
DTCs
This diagnostic service gains access to emission-related power train trouble codes which
were stored by ECM.
Service $04
CLEAR DIAG INFO
This diagnostic service can clear all emission-related diagnostic information. This in-
cludes:
• Clear number of diagnostic trouble codes (Service $01)
• Clear diagnostic trouble codes (Service $03)
• Clear trouble code for freeze frame data (Service $01)
• Clear freeze frame data (Service $02)
• Reset status of system monitoring test (Service $01)
• Clear on board monitoring test results (Service $06 and $07)
Service $06
(ON BOARD TESTS)
This diagnostic service accesses the results of on board diagnostic monitoring tests of
specific components/systems that are not continuously monitored.
Service $07
(ON BOARD TESTS)
This diagnostic service enables the off board test drive to obtain test results for emission-
related powertrain components/systems that are continuously monitored during normal
driving conditions.
Service $08
—
This diagnostic service can close EVAP system in ignition switch ON position (Engine
stopped). When this diagnostic service is performed, EVAP canister vent control valve can
be closed.
In the following conditions, this diagnostic service cannot function.
• Low ambient temperature
• Low battery voltage
• Engine running
• Ignition switch OFF
• Low fuel temperature
• Too much pressure is applied to EVAP system
Service $09
(CALIBRATION ID)
This diagnostic service enables the off-board test device to request specific vehicle infor-
mation such as Vehicle Identification Number (VIN) and Calibration IDs.
JMBIA1123ZZ
Revision: 2008 October
2009 Murano
EC-126
< FUNCTION DIAGNOSIS >
[VQ35DE]
ON BOARD DIAGNOSTIC (OBD) SYSTEM
4.
Enter the program according to instruction on the screen or in
the operation manual.
(*: Regarding GST screens in this section, sample screens are
shown.)
5.
Perform each diagnostic mode according to each service proce-
dure.
For further information, see the GST Operation Manual of
the tool maker.
SEF398S
SEF416S
Revision: 2008 October
2009 Murano
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
EC-127
< COMPONENT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
COMPONENT DIAGNOSIS
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
Description
INFOID:0000000003387929
The specification (SP) value indicates the tolerance of the value that is displayed in “SPEC” in “DATA MONI-
TOR” mode of CONSULT-III during normal operation of the Engine Control System. When the value in “SPEC”
in “DATA MONITOR” mode is within the SP value, the Engine Control System is confirmed OK. When the
value in “SPEC” in “DATA MONITOR” mode is NOT within the SP value, the Engine Control System may have
one or more malfunctions.
The SP value is used to detect malfunctions that may affect the Engine Control System, but will not illuminate
the MIL.
The SP value will be displayed for the following three items:
• B/FUEL SCHDL (The fuel injection pulse width programmed into ECM prior to any learned on board correc-
tion)
• A/F ALPHA-B1/B2 (The mean value of air-fuel ratio feedback correction factor per cycle)
• MAS A/F SE-B1 (The signal voltage of the mass air flow sensor)
Component Function Check
INFOID:0000000003387930
1.
START
Check that all of the following conditions are satisfied.
• Vehicle driven distance: More than 5,000 km (3,107 miles)
• Barometric pressure: 98.3 - 104.3 kPa (1.003 - 1.064 kg/cm
2
, 14.25 - 15.12 psi)
• Atmospheric temperature: 20 - 30
°
C (68 - 86
°
F)
• Engine coolant temperature: 75 - 95
°
C (167 - 203
°
F)
• Transmission: Warmed-up
- After the engine is warmed up to normal operating temperature, drive vehicle until “FLUID TEMP SE” (CVT
fluid temperature sensor signal) indicates more than 60
°
C (140
°
F).
• Electrical load: Not applied
- Rear window defogger switch, air conditioner switch lighting switch are OFF. Steering wheel is straight
ahead.
• Engine speed: Idle
>> GO TO 2.
2.
PERFORM “SPEC” OF “DATA MONITOR” MODE
With CONSULT-III
NOTE:
Perform “SPEC” in “DATA MONITOR” mode in maximum scale display.
1.
EC-12, "BASIC INSPECTION : Special Repair Requirement"
2.
Select “B/FUEL SCHDL”, “A/F ALPHA-B1”, “A/F ALPHA-B2” and “MAS A/F SE-B1” in “SPEC” of “DATA
MONITOR” mode with CONSULT-III.
3.
Check that monitor items are within the SP value.
Is the measurement value within the SP value?
YES
>> INSPECTION END
NO
>> Go to
Revision: 2008 October
2009 Murano
EC-128
< COMPONENT DIAGNOSIS >
[VQ35DE]
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
Diagnosis Procedure
INFOID:0000000003387931
OVERALL SEQUENCE
JMBIA1468GB
Revision: 2008 October
2009 Murano
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
EC-129
< COMPONENT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
DETAILED PROCEDURE
1.
CHECK “A/F ALPHA-B1”, “A/F ALPHA-B2”
With CONSULT-III
1.
Start engine.
2.
Confirm that the testing conditions are met. Refer to
EC-127, "Component Function Check"
3.
Select “A/F ALPHA-B1”, “A/F ALPHA-B2” in “SPEC” of “DATA MONITOR” mode, and check that each
indication is within the SP value.
PBIB3214E
Revision: 2008 October
2009 Murano
EC-130
< COMPONENT DIAGNOSIS >
[VQ35DE]
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
NOTE:
Check “A/F ALPHA-B1”, “A/F ALPHA-B2” for approximately 1 minute because they may fluctuate. It is NG
if the indication is out of the SP value even a little.
Is the measurement value within the SP value?
YES
>> GO TO 17.
NO-1
>> Less than the SP value: GO TO 2.
NO-2
>> More than the SP value: GO TO 3.
2.
CHECK “B/FUEL SCHDL”
Select “B/FUEL SCHDL” in “SPEC” of “DATA MONITOR” mode, and check that the indication is within the SP
value.
Is the measurement value within the SP value?
YES
>> GO TO 4.
NO
>> More than the SP value: GO TO 19.
3.
CHECK “B/FUEL SCHDL”
Select “B/FUEL SCHDL” in “SPEC” of “DATA MONITOR” mode, and check that the indication is within the SP
value.
Is the measurement value within the SP value?
YES
>> GO TO 6.
NO-1
>> More than the SP value: GO TO 6.
NO-2
>> Less than the SP value: GO TO 25.
4.
CHECK “A/F ALPHA-B1”, “A/F ALPHA-B2”
1.
Stop the engine.
2.
Disconnect PCV hose, and then plug it.
3.
Start engine.
4.
Select “A/F ALPHA-B1”, “A/F ALPHA-B2” in “SPEC” of “DATA MONITOR” mode, and check that each
indication is within the SP value.
Is the measurement value within the SP value?
YES
>> GO TO 5.
NO
>> GO TO 6.
5.
CHANGE ENGINE OIL
1.
Stop the engine.
2.
Change engine oil.
NOTE:
This symptom may occur when a large amount of gasoline is mixed with engine oil because of driving
conditions (such as when engine oil temperature does not rise enough since a journey distance is too
short during winter). The symptom will not be detected after changing engine oil or changing driving con-
ditions.
>> INSPECTION END
6.
CHECK FUEL PRESSURE
Check fuel pressure. (Refer to
Is the inspection result normal?
YES
>> GO TO 9.
NO-1
>> Fuel pressure is too high: Replace “fuel filter and fuel pump assembly” and then. GO TO 8.
NO-2
>> Fuel pressure is too low: GO TO 7.
7.
DETECT MALFUNCTIONING PART
Check fuel hoses and fuel tubes for clogging.
Is the inspection result normal?
YES
>> Replace “fuel filter and fuel pump assembly” and then GO TO 8.
NO
>> Repair or replace malfunctioning part and then GO TO 8.
8.
CHECK “A/F ALPHA-B1”, “A/F ALPHA-B2”
Revision: 2008 October
2009 Murano
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
EC-131
< COMPONENT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
1.
Start engine.
2.
Select “A/F ALPHA-B1”, “A/F ALPHA-B2” in “SPEC” of “DATA MONITOR” mode, and check that each
indication is within the SP value.
Is the measurement value within the SP value?
YES
>> INSPECTION END
NO
>> GO TO 9.
9.
PERFORM POWER BALANCE TEST
1.
Perform “POWER BALANCE” in “ACTIVE TEST” mode.
2.
Check that the each cylinder produces a momentary engine speed drop.
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> GO TO 10.
10.
DETECT MALFUNCTIONING PART
Check the following below.
• Ignition coil and its circuit (Refer to
EC-451, "Component Function Check"
• Fuel injector and its circuit (Refer to
EC-444, "Component Function Check"
• Intake air leakage
• Low compression pressure (Refer to
Is the inspection result normal?
YES
>> Replace fuel injector and then GO TO 11.
NO
>> Repair or replace malfunctioning part and then GO TO 11.
11.
CHECK “A/F ALPHA-B1”, “A/F ALPHA-B2”
1.
Start engine.
2.
Select “A/F ALPHA-B1”, “A/F ALPHA-B2” in “SPEC” of “DATA MONITOR” mode, and check that each
indication is within the SP value.
Is the measurement value within the SP value?
YES
>> INSPECTION END
NO
>> GO TO 12.
12.
CHECK A/F SENSOR 1 FUNCTION
Perform all DTC CONFIRMATION PROCEDURE related with A/F sensor 1.
• For DTC P0130, P0150, refer to
.
• For DTC P0131, P0151, refer to
.
• For DTC P0132, P0152, refer to
.
• For DTC P0133, P0153, refer to
.
• For DTC P2A00, P2A03, refer to
Are any DTCs detected?
YES
>> GO TO 15.
NO
>> GO TO 13.
13.
CHECK A/F SENSOR 1 CIRCUIT
Perform Diagnostic Procedure according to corresponding DTC.
>> GO TO 14.
14.
CHECK “A/F ALPHA-B1”, “A/F ALPHA-B2”
1.
Start engine.
2.
Select “A/F ALPHA-B1”, “A/F ALPHA-B2” in “SPEC” of “DATA MONITOR” mode, and check that each
indication is within the SP value.
Is the measurement value within the SP value?
YES
>> INSPECTION END
NO
>> GO TO 15.
15.
DISCONNECT AND RECONNECT ECM HARNESS CONNECTOR
1.
Stop the engine.
Revision: 2008 October
2009 Murano
EC-132
< COMPONENT DIAGNOSIS >
[VQ35DE]
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
2.
Disconnect ECM harness connector. Check pin terminal and connector for damage, and then reconnect it.
>> GO TO 16.
16.
CHECK “A/F ALPHA-B1”, “A/F ALPHA-B2”
1.
Start engine.
2.
Select “A/F ALPHA-B1”, “A/F ALPHA-B2” in “SPEC” of “DATA MONITOR” mode, and check that each
indication is within the SP value.
Is the measurement value within the SP value?
YES
>> INSPECTION END
NO
>> Detect malfunctioning part according to
.
17.
CHECK “B/FUEL SCHDL”
Select “B/FUEL SCHDL” in “SPEC” of “DATA MONITOR” mode, and check that the indication is within the SP
value.
Is the measurement value within the SP value?
YES
>> INSPECTION END
NO-1
>> More than the SP value: GO TO 18.
NO-2
>> Less than the SP value: GO TO 25.
18.
DETECT MALFUNCTIONING PART
1.
Check for the cause of large engine friction. Refer to the following.
-
Engine oil level is too high
-
Engine oil viscosity
-
Belt tension of power steering, alternator, A/C compressor, etc. is excessive
-
Noise from engine
-
Noise from transmission, etc.
2.
Check for the cause of insufficient combustion. Refer to the following.
-
Valve clearance malfunction
-
Intake valve timing control function malfunction
-
Camshaft sprocket installation malfunction, etc.
>> Repair or replace malfunctioning part, and then GO TO 30.
19.
CHECK INTAKE SYSTEM
Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.
• Crushed air ducts
• Malfunctioning seal of air cleaner element
• Uneven dirt of air cleaner element
• Improper specification of intake air system
Is the inspection result normal?
YES
>> GO TO 21.
NO
>> Repair or replace malfunctioning part, and then GO TO 20.
20.
CHECK “A/F ALPHA-B1”, “A/F ALPHA-B2”, AND “B/FUEL SCHDL”
Select “A/F ALPHA-B1”, “A/F ALPHA-B2”, and “B/FUEL SCHDL” in “SPEC” of “DATA MONITOR” mode, and
check that each indication is within the SP value.
Is the measurement value within the SP value?
YES
>> INSPECTION END
NO
>> “B/FUEL SCHDL” is more, “A/F ALPHA-B1”, “A/F ALPHA-B2” are less than the SP value: GO TO
21.
21.
DISCONNECT AND RECONNECT MASS AIR FLOW SENSOR HARNESS CONNECTOR
1.
Stop the engine.
2.
Disconnect mass air flow sensor harness connector. Check pin terminal and connector for damage and
then reconnect it again.
>> GO TO 22.
Revision: 2008 October
2009 Murano
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
EC-133
< COMPONENT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
22.
CHECK “A/F ALPHA-B1”, “A/F ALPHA-B2”
1.
Start engine.
2.
Select “A/F ALPHA-B1”, “A/F ALPHA-B2” in “SPEC” of “DATA MONITOR” mode, and check that each
indication is within the SP value.
Is the measurement value within the SP value?
YES
>> Detect malfunctioning part of mass air flow sensor circuit and repair it. Refer to
. Then GO TO 29.
NO
>> GO TO 23.
23.
CHECK “MAS A/F SE-B1”
Select “MAS A/F SE-B1” in “SPEC” of “DATA MONITOR” mode, and check that the indication is within the SP
value.
Is the measurement value within the SP value?
YES
>> GO TO 24.
NO
>> More than the SP value: Replace mass air flow sensor, and then GO TO 29.
24.
REPLACE ECM
1.
Replace ECM.
2.
EC-15, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
.
>> GO TO 29.
25.
CHECK INTAKE SYSTEM
Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.
• Crushed air ducts
• Malfunctioning seal in air cleaner element
• Uneven dirt in air cleaner element
• Improper specification in intake air system
Is the inspection result normal?
YES
>> GO TO 27.
NO
>> Repair or replace malfunctioning part, and then GO TO 26.
26.
CHECK “B/FUEL SCHDL”
Select “B/FUEL SCHDL” in “SPEC” of “DATA MONITOR” mode, and check that the indication is within the SP
value.
Is the measurement value within the SP value?
YES
>> INSPECTION END
NO
>> Less than the SP value: GO TO 27.
27.
CHECK “MAS A/F SE-B1”
Select “MAS A/F SE-B1” in “SPEC” of “DATA MONITOR” mode, and check that the indication is within the SP
value.
Is the measurement value within the SP value?
YES
>> GO TO 28.
NO
>> Less than the SP value: Replace mass air flow sensor, and then GO TO 30.
28.
CHECK INTAKE SYSTEM
Check for the cause of air leakage after the mass air flow sensor. Refer to the following.
• Disconnection, looseness, and cracks in air duct
• Looseness of oil filler cap
• Disconnection of oil level gauge
• Open stuck, breakage, hose disconnection, or cracks in PCV valve
• Disconnection or cracks in EVAP purge hose, stuck open EVAP canister purge volume control solenoid
valve
• Malfunctioning seal in rocker cover gasket
• Disconnection, looseness, or cracks in hoses, such as a vacuum hose, connecting to intake air system parts
Revision: 2008 October
2009 Murano
EC-134
< COMPONENT DIAGNOSIS >
[VQ35DE]
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
• Malfunctioning seal in intake air system, etc.
>> GO TO 30.
29.
CHECK “A/F ALPHA-B1”, “A/F ALPHA-B2”, AND “B/FUEL SCHDL”
Select “A/F ALPHA-B1”, “A/F ALPHA-B2”, and “B/FUEL SCHDL” in “SPEC” of “DATA MONITOR” mode, and
check that each indication is within the SP value.
Is the measurement value within the SP value?
YES
>> INSPECTION END
NO
>> Detect malfunctioning part according to
.
30.
CHECK “B/FUEL SCHDL”
Select “B/FUEL SCHDL” in “SPEC” of “DATA MONITOR” mode, and then check that the indication is within
the SP value.
Is the measurement value within the SP value?
YES
>> INSPECTION END
NO
>> Detect malfunctioning part according to
.
Revision: 2008 October
2009 Murano
POWER SUPPLY AND GROUND CIRCUIT
EC-135
< COMPONENT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000004752070
1.
CHECK GROUND CONNECTION
1.
Turn ignition switch OFF.
2.
Check ground connection E38. Refer to Ground Inspection in
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connection.
2.
CHECK ECM GROUND CIRCUIT FOR OPEN AND SHORT
1.
Disconnect ECM harness connector.
2.
Check the continuity between ECM harness connector and ground.
3.
Also check harness for short to power.
is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors F121, E7
• Harness for open or short between ECM and ground
>> Repair open circuit or short to power in harness or connectors.
4.
CHECK ECM POWER SUPPLY CIRCUIT-I
1.
Reconnect ECM harness connector.
2.
Turn ignition switch OFF and then ON.
3.
Check the voltage between ECM harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 5.
5.
DETECT MALFUNCTIONING PART
Check the following.
• IPDM E/R connector E10
• 10 A fuse (No. 44)
• Harness for open or short between ECM and IPDM E/R
ECM
Ground
Continuity
Connector
Terminal
F7
12
Ground
Existed
16
E16
107
108
111
112
ECM
Voltage
Connector
+
–
Terminal
Terminal
E16
93
112
Battery voltage
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст