Nissan Murano Z51 (2008 year). Manual — part 244
INT-8
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003600920
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors while ignition switch is
ON or engine is running, never use air or electric power tools or strike near the sensor(s) with a hammer.
Heavy vibration may activate the sensor(s), deploy the airbag(s), possibly cause serious injury.
When using air or electric power tools or hammers, always turn OFF ignition switch, disconnect the battery,
and wait 3 minutes or more before performing any service.
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
INFOID:0000000003600921
NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4.
Perform the necessary repair operation.
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT-III.
Revision: 2008 October
2009 Murano
PRECAUTIONS
INT-9
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Precaution for Procedure without Cowl Top Cover
INFOID:0000000003600922
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
Precaution for Work
INFOID:0000000003600923
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operation.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
PIIB3706J
Revision: 2008 October
2009 Murano
INT-10
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000004758287
Special Service Tools
INFOID:0000000004758286
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes clips, pawls and metal clips
Power tool
SIIA0995E
JMKIA3050ZZ
PIIB1407E
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-43980)
NISSAN Squeak and Rattle
Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
Revision: 2008 October
2009 Murano
DOOR FINISHER
INT-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
ON-VEHICLE REPAIR
DOOR FINISHER
FRONT DOOR FINISHER
FRONT DOOR FINISHER : Exploded View
INFOID:0000000003443011
FRONT DOOR FINISHER : Removal and Installation
INFOID:0000000003443012
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth before remove.
REMOVAL
1.
Fully open front door window.
1.
Inside handle escutcheon
2.
Step lamp
3.
Power window switch finisher
4.
Front door finisher
5.
Front door inside handle
6.
Seat memory switch finisher
7.
Front door panel
8.
Front door inside seal
9.
Armrest finisher
10. Door mirror corner cover
11. Power window switch
12. Door mirror remote control switch
: Clip
: Pawl
JMJIA1348ZZ
Revision: 2008 October
2009 Murano
INT-12
< ON-VEHICLE REPAIR >
DOOR FINISHER
2.
Remove inside handle escutcheon (1) with remover tool (A).
3.
Remove bolt (B) located behind the inside handle escutcheon
with tool (A).
4.
Pull up power window switch finisher (1) with remover tool (A) to
disengage the pawls.
5.
Disconnect power window and door mirror remote control switch harness connectors, and then remove
power window switch finisher.
6.
Remove bolt (B) located behind power window switch finisher
with tool (A).
: Pawl
JMJIA1350ZZ
JMJIA1351ZZ
: Pawl
JMJIA1352ZZ
JMJIA1353ZZ
Revision: 2008 October
2009 Murano
DOOR FINISHER
INT-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
7.
Remove armrest finisher (1) with remover tool (A).
8.
Remove the bolt (B) located behind the armrest finisher with tool
(A).
9.
Remove step lamp (1) with remover tool (A) and then disconnect
the harness connector. Refer to
INL-121, "Removal and Installa-
10. Remove seat memory switch finisher (1) and rear heated seat (LH/RH) switch finisher (2) with remover
tool (A) and then disconnect the harness connectors. (With sunroof)
: Pawl
JMJIA1355ZZ
JMJIA1356ZZ
: Pawl
JMJIA1357ZZ
: Pawl
JMJIA1358ZZ
Revision: 2008 October
2009 Murano
INT-14
< ON-VEHICLE REPAIR >
DOOR FINISHER
11. Insert remover tool (A) between door finisher and door panel to
disengage door finisher mounting clips, starting from the bottom
and working to the top.
12. Pull up front door finisher and pull out.
13. Disconnect lock knob cable (1) and inside handle cable (2) from
front door inside handle (3).
14. Remove front door finisher.
15. Remove the inside handle after removing front door finisher. Refer to
.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When installing door finisher, check that clips are securely fitted in panel holes on body, and then
press them in.
REAR DOOR FINISHER
: Clip
JMJIA1362ZZ
JMJIA1359ZZ
Revision: 2008 October
2009 Murano
DOOR FINISHER
INT-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
REAR DOOR FINISHER : Exploded View
INFOID:0000000003443013
REAR DOOR FINISHER : Removal and Installation
INFOID:0000000003443437
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth before remove.
REMOVAL
1.
Fully open rear door window.
2.
Remove inside handle escutcheon (1) with remover tool (A).
1.
Inside handle escutcheon
2.
Step lamp
3.
Power window switch finisher
4.
Rear door finisher
5.
Rear door inside handle
6.
Rear heated seat switch finisher
7.
Rear door panel
8.
Rear door inside seal
9.
Armrest finisher
10. Power window switch
: Clip
: Pawl
JMJIA1349ZZ
: Pawl
JMJIA1350ZZ
Revision: 2008 October
2009 Murano
INT-16
< ON-VEHICLE REPAIR >
DOOR FINISHER
3.
Remove bolt (B) located behind the inside handle escutcheon
with tool (A).
4.
Pull up power window switch finisher (1) with remover tool (A) to
disengage the pawls.
5.
Disconnect power window switch connector, and then remove power window switch finisher.
6.
Remove bolt (B) located behind power window switch finisher
with tool (A).
7.
Remove armrest finisher (1) with remover tool (A).
JMJIA1351ZZ
: Pawl
JMJIA1361ZZ
JMJIA1354ZZ
: Pawl
JMJIA1355ZZ
Revision: 2008 October
2009 Murano
DOOR FINISHER
INT-17
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
8.
Remove bolt (B) located behind armrest finisher with tool (A).
9.
Remove seat memory switch finisher (1) and rear heated seat (LH/RH) switch finisher (2) with remover
tool (A), then disconnect the harness connectors. (With sunroof)
10. Insert remover tool (A) between door finisher and door panel to
disengage door finisher mounting clips, starting from the bottom
and working to the top.
11. Pull up rear door finisher and pull out.
12. Disconnect lock knob cable (1) and inside handle cable (2) from
rear door inside handle (3).
13. Remove rear door finisher.
14. Remove the inside handle after removing rear door finisher. Refer to
.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
JMJIA1356ZZ
: Pawl
JMJIA1358ZZ
: Clip
JMJIA1360ZZ
JMJIA1359ZZ
Revision: 2008 October
2009 Murano
INT-18
< ON-VEHICLE REPAIR >
DOOR FINISHER
When installing door finisher, check that clips are securely fitted in panel holes on body, and then
press them in.
Revision: 2008 October
2009 Murano
BODY SIDE TRIM
INT-19
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BODY SIDE TRIM
Exploded View
INFOID:0000000003443015
Removal and Installation
INFOID:0000000003443016
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
REMOVAL
FRONT PILLAR GARNISH
1.
Remove front body side welt partially.
1.
Front body side welt
2.
Rear body side welt
3.
Front pillar garnish
4.
Front kicking plate (inner)
5.
Dash side finisher
6.
Rear kicking plate (inner)
7.
Center pillar lower garnish
8.
Center pillar upper garnish
9.
Front kicking plate (outer)
10. Rear kicking plate (outer)
11. Bolt cover
: Clip
: Pawl
: Metal clip
Refer to
for symbols in the figure.
JMJIA1363ZZ
Revision: 2008 October
2009 Murano
INT-20
< ON-VEHICLE REPAIR >
BODY SIDE TRIM
2.
Disengage front pillar garnish (1) mounting clips with remover
tool (A).
3.
Pull front pillar garnish (1) partially toward the vehicle.
4.
Insert remover tool (A) between mounting clip bottom side and body side to disengage front pillar garnish
(1) mounting clip.
5.
Once free, pull front pillar garnish (1) upwards to disengage the lower locating tab from instrument panel.
6.
Remove front pillar garnish (1).
FRONT KICKING PLATE INNER
1.
Disengage the pawls and metal clip from the body panel with
remover tool (A).
2.
Remove front kicking plate inner (1).
FRONT KICKING PLATE OUTER
1.
Disengage the pawls from the body panel with remover tool (A).
2.
Remove front kicking plate outer (1).
DASH SIDE FINISHER
1.
Remove front kicking plate inner.
: Clip
JMJIA1364ZZ
JMJIA2757ZZ
: Pawl
: Metal clip
JMJIA1365ZZ
: Pawl
JMJIA1366ZZ
Revision: 2008 October
2009 Murano
BODY SIDE TRIM
INT-21
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
2.
Disengage dash side finisher (1) mounting clip with remover tool
(A).
3.
Remove dash side finisher (1).
REAR KICKING PLATE INNER
1.
Disengage the pawls from the body with remover tool (A).
2.
Remove rear kicking plate inner (1).
REAR KICKING PLATE OUTER
1.
Disengage the pawls from the body side panel with remover tool
(A).
2.
Remove rear kicking plate outer (1).
CENTER PILLAR LOWER GARNISH
1.
Remove front kicking plate inner and rear kicking plate inner.
2.
Insert remover tool (A) between center pillar lower garnish (1)
and body side panel to disengage the metal clips.
3.
Remove anchor bolt cover (2), then remove the anchor bolt
behind the cover.
4.
Remove center pillar lower garnish (1).
CENTER PILLAR UPPER GARNISH
1.
Remove partially front and rear body side welt.
2.
Remove front kicking plate inner and rear kicking plate inner.
3.
Remove center pillar lower garnish.
4.
Remove front seat belt shoulder anchor (2).
: Clip
JMJIA2448ZZ
: Pawl
JMJIA1368ZZ
: Pawl
JMJIA1369ZZ
: Metal clip
JMJIA1370ZZ
Revision: 2008 October
2009 Murano
INT-22
< ON-VEHICLE REPAIR >
BODY SIDE TRIM
5.
Remove the bolt located behind the cover (A).
6.
Pull back center pillar upper garnish to disengage clips and
remove center pillar upper garnish from the body side panel.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When installing body side trim, check that clips are securely fitted in panel holes on body, and then
press them in.
JMJIA1371ZZ
Revision: 2008 October
2009 Murano
FLOOR TRIM
INT-23
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
FLOOR TRIM
Exploded View
INFOID:0000000003443017
Removal and Installation
INFOID:0000000003443018
REMOVAL
1.
Remove front seat assembly (LH/RH). Refer to
SE-106, "Removal and Installation"
2.
Remove rear seat cushion frame and reclining device assembly mounting bolts. Refer to
3.
Remove dash side finisher (LH/RH), front kicking plate inner (LH/RH), center pillar lower garnish (LH/RH),
and rear kicking plate inner (LH/RH). Refer to
INT-19, "Removal and Installation"
4.
Remove center console assembly. Refer to
IP-20, "Removal and Installation"
.
5.
Remove console bracket mounting nuts (A), and then remove console bracket LH (1).
6.
Remove rear foot duct (2), rear foot duct (3) and rear ventilator duct (4).
1.
Floor carpet assembly
2.
Floor hook
JMJIA2449ZZ
JMJIA1373ZZ
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст