Nissan Murano Z51 (2008 year). Manual — part 245
INT-24
< ON-VEHICLE REPAIR >
FLOOR TRIM
7.
Remove screw shown by the arrow in the figure, and then
remove rear ventilator duct (1).
8.
Disengage the clip of floor hook (1) with a remover tool (A).
9.
Disconnect harness connectors (A) and remove floor harness
mounting clips as shown by the arrows in the figure.
10. Remove rear console bracket assembly. Refer to
IP-20, "Removal and Installation"
11. Remove the center console sub harness. Refer to
IP-20, "Removal and Installation"
.
12. Remove floor carpet fixing clips (A) and then remove floor car-
pet.
INSTALLATION
Install in the reverse order of removal.
: Vehicle front
: Bolt
JMJIA1375ZZ
: Clip
JMJIA0092GB
: Clip
JMJIA1374ZZ
JMJIA1376ZZ
Revision: 2008 October
2009 Murano
HEADLINING
INT-25
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
HEADLINING
NORMAL ROOF
NORMAL ROOF : Exploded View
INFOID:0000000004758279
1.
Sun-visor assembly (LH/RH)
2.
Sun-visor holder (LH/RH)
3.
Sun-visor cover (LH/RH)
4.
Roof harness
5.
Assist grip cap
6.
Assist grip
7.
Personal lamp assembly
8.
Headlining clip
9.
Rear DVD harness
10. Center seat belt retractor cov-
er
11. Headlining assembly
12. Roof plate assembly
13. Antenna feeder harness
14. Roof console assembly
15. Dual-lock fastener
16. Roof insulator
17. Map lamp bracket
18. Roof bracket
19. Roof console
20. Map lamp assembly
21. Map lamp lens
: Clip
: Pawl
: Metal clip
: Vehicle front
JMJIA2692ZZ
Revision: 2008 October
2009 Murano
INT-26
< ON-VEHICLE REPAIR >
HEADLINING
NORMAL ROOF : Removal and Installation
INFOID:0000000004758280
REMOVAL
1.
Remove front seat belt anchor bolt (LH/RH). Refer to
SB-7, "SEAT BELT BUCKLE : Exploded View"
2.
Remove rear seat belt anchor bolt (LH/RH). Refer to
SB-12, "SEAT BELT BUCKLE : Exploded View"
.
3.
Remove luggage side lower finisher (LH/RH), luggage side upper finisher (LH/RH). Refer to
4.
Remove front pillar garnish (LH/RH), front kicking plate (LH/RH), center pillar lower garnish (LH/RH), cen-
ter pillar upper garnish (LH/RH), front body side welt (LH/RH), rear body side welt (LH/RH) and rear kick-
ing plate (LH/RH). Refer to
INT-19, "Removal and Installation"
5.
Disconnect roof harness (1) connectors (A), the antenna feeder (2) harness connector (C) and the clips
(B).
6.
Disengage the rear display unit fixing clips with a remover tool, disconnect the harness connector and
then remove the rear display unit. Refer to
AV-524, "Removal and Installation"
.
7.
Remove sun-visor (LH/RH).
• Remove sun-visor cover.
• Remove mounting screws.
• Disconnect vanity mirror lamp harness connector (With vanity mirror lamp)
8.
Disconnect inside mirror and rain sensor harness connector. Refer to
.
9.
Rotate 90 degrees and remove sun-visor holder (1) (LH/RH).
10. With flat-bladed screwdriver (A), press the upper side mounting
plastic clip (1) and pull up to remove the mounting plastic clip (1)
from assist grip (2).
•
L: Left side of vehicle
R: Right side of vehicle
JMJIA2760ZZ
JMJIA0098GB
JMJIA2790ZZ
Revision: 2008 October
2009 Murano
HEADLINING
INT-27
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
11. Once the mounting plastic clip (1) is removed, pull out the assist
grip (2) to remove.
12. Recline front seat back to facilitate the headlining removal.
13. Pull map lamp assembly toward and disengage metal clips (B)
and dual-lock fastener (A).
CAUTION:
Map lamp assembly is crimped from the back of headlining.
Remove it by disengaging the crimped area of back of map
lamp assembly after removing headlining from the vehicle.
14. Disengage center seat belt retractor cover(1) fixing clips and
metal clip with remover tool (A), then remove rear center seat
belt cover.
15. Disconnect the antenna feeder harness connectors (A), (B), the roof harness connector (C) and clips (D).
16. Using remover tool, remove headlining clip at the back side of headlining.
JMJIA1380ZZ
JMJIA1008ZZ
: Clip
: Metal clip
JMJIA2759ZZ
(1): Right side of vehicle
(2): Left side of vehicle
JMJIA2729ZZ
Revision: 2008 October
2009 Murano
INT-28
< ON-VEHICLE REPAIR >
HEADLINING
17. Remove headlining (1) from back door.
CAUTION:
• When removing the headlining, 2 workers are required.
• Never bend headlining when removing.
• Be careful not to scratch or damage any part of the body
while taking out the headlining.
18. Remove the following parts after removing headlining.
• Map lamp assembly. Refer to
INL-115, "Removal and Installation"
.
• Personal lamp. Refer to
INL-122, "Removal and Installation"
.
• Roof harness assembly.
• Antenna feeder harness assembly. Refer to the following.
- Base audio. Refer to
- Bose audio without navigation. Refer to
.
- Bose audio with navigation. Refer to
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• As for guide, install first sun-visor holder (LH/RH) and then the rear headlining clips at the back side
of headlining.
• Be careful not to bend the headlining when installing.
SUNROOF
JMJIA1010ZZ
Revision: 2008 October
2009 Murano
HEADLINING
INT-29
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
SUNROOF : Exploded View
INFOID:0000000004758281
SUNROOF : Removal and Installation
INFOID:0000000004758282
REMOVAL
1.
Remove front seat belt anchor bolt (LH/RH). Refer to
SB-7, "SEAT BELT BUCKLE : Exploded View"
2.
Remove rear seat belt anchor bolt (LH/RH). Refer to
SB-12, "SEAT BELT BUCKLE : Exploded View"
1.
Sun-visor assembly (LH/RH)
2.
Sun-visor holder (LH/RH)
3.
Sun-visor cover (LH/RH)
4.
Roof harness
5.
Assist grip cap
6.
Assist grip
7.
Personal lamp assembly
8.
Headlining clip
9.
Center seat belt retractor cover
10. Headlining assembly
11. Antenna feeder
12. Roof console assembly
13. Dual-lock fastener
14. Roof insulator
15. Roof console
16. Roof bracket
17. Map lamp assembly
18. Map lamp lens
: Clip
: Pawl
: Metal clip
: Vehicle front
JMJIA2693ZZ
Revision: 2008 October
2009 Murano
INT-30
< ON-VEHICLE REPAIR >
HEADLINING
3.
Remove luggage side lower finisher (LH/RH), luggage side upper finisher (LH/RH). Refer to
4.
Remove front pillar garnish (LH/RH), front kicking plate (LH/RH), center pillar lower garnish (LH/RH), cen-
ter pillar upper garnish (LH/RH), front body side welt (LH/RH), rear body side welt (LH/RH) and rear kick-
ing plate (LH/RH). Refer to
INT-19, "Removal and Installation"
5.
Disconnect roof harness (1) connectors (A), the antenna feeder (2) harness connector (C) and the clips
(B).
6.
Remove sun-visor (LH/RH).
• Remove sun-visor cap.
• Remove mounting screws.
• Disconnect vanity mirror lamp harness connector. (With vanity mirror lamp)
7.
Disconnect inside mirror and rain sensor harness connector. Refer to
MIR-61, "Removal and Installation"
.
8.
Rotate 90 degrees and remove sun-visor holder (1) (LH/RH).
9.
With a flat-bladed screwdriver (A), press the upper side of
mounting plastic clip (1) and pull up to remove the mounting
plastic clip (1) from assist grip (2).
•
L: Left side of vehicle
R: Right side of vehicle
JMJIA2760ZZ
JMJIA0098GB
JMJIA2790ZZ
Revision: 2008 October
2009 Murano
HEADLINING
INT-31
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
10. Once the mounting plastic clip (1) is removed, pull out the assist
grip (2) to remove.
11. Recline front seat back to facilitate the headlining removal.
12. Insert a remover tool (A) between the headlining and the roof
console assembly (1) to disengage the fixing pawls and metal
clips, disconnect the connectors and remove the roof console
assembly.
13. Disengage rear center seat belt cover (1) fixing clips and metal
clip with remover tool (A), then remove rear center seat belt
cover.
14. Disconnect the antenna feeder harness connectors (A), (B), the roof harness connector (C) and the clips
(D).
15. Using remover tool, remove headlining clip at the back side of headlining.
JMJIA1380ZZ
: Pawl
: Metal clip
JMJIA2761ZZ
: Clip
: Metal clip
JMJIA2759ZZ
(1): Right side of vehicle
(2):Left side of vehicle
JMJIA2729ZZ
Revision: 2008 October
2009 Murano
INT-32
< ON-VEHICLE REPAIR >
HEADLINING
16. Remove headlining (1) from back door.
CAUTION:
• When removing the headlining, 2 workers are required.
• Never bend headlining when removing.
• Be careful not to scratch or damage any part of the body
while taking out the headlining.
17. Remove the following parts after removing headlining.
• Map lamp assembly. Refer to
INL-115, "Removal and Installation"
.
• Personal lamp. Refer to
INL-122, "Removal and Installation"
.
• Roof harness assembly
• Antenna feeder harness assembly. Refer to the following.
- Base audio. Refer to
- Bose audio without navigation. Refer to
.
- Bose audio with navigation. Refer to
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• As for guide, install first sun-visor holder (LH/RH) and then the rear headlining clips at the back side
of headlining.
• Be careful not to bend the headlining when installing.
JMJIA1010ZZ
Revision: 2008 October
2009 Murano
LUGGAGE FLOOR TRIM
INT-33
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
LUGGAGE FLOOR TRIM
Exploded View
INFOID:0000000003443023
1.
Luggage rear plate
2.
Belt assembly
3.
Rear rope hook
4.
Luggage room power socket
5.
Luggage side finisher upper (RH)
6.
Luggage side finisher lower (RH)
7.
Luggage floor finisher (RH)
8.
Luggage floor spacer (RH)
9.
Luggage mask
10. Luggage floor finisher front
11. Luggage floor board
12. Spare tire cover
13. Tonneau cover
14. Net
15. Luggage side finisher lower (LH)
16. Luggage floor spacer (LH)
17. Luggage floor finisher (LH)
18. Luggage floor finisher center (front)
19. Luggage floor finisher center (rear)
20. Luggage side finisher upper (LH)
21. Rear plate ornament (RH)
JMJIA1386ZZ
Revision: 2008 October
2009 Murano
INT-34
< ON-VEHICLE REPAIR >
LUGGAGE FLOOR TRIM
Removal and Installation
INFOID:0000000003443024
REMOVAL
LUGGAGE FLOOR FINISHER CENTER
1.
Fully open back door.
2.
Remove tonneau cover assembly.
3.
Remove luggage floor finisher (RH/LH).
4.
Open luggage floor finisher center rear (1), turn the clip (A) as
shown in the figure, and then remove the luggage floor finisher
center rear.
5.
Remove luggage floor finisher front (1) fixing bolts (A) (LH/RH)
and remove luggage floor finisher front.
6.
Remove the luggage floor finisher center (front) both bolts, then remove the luggage floor finisher center
(front).
LUGGAGE SIDE FINISHER UPPER
1.
Remove rear seat belt anchor bolt (upper).
2.
Remove hook trunk net.
3.
Remove tonneau cover and remove the luggage side finisher upper fixing bolts and clips.
4.
Remove luggage side finisher upper clips and metal clips with remover tool.
5.
Remove luggage side finisher upper from the body side panel.
LUGGAGE SIDE FINISHER LOWER
1.
Remove rear kicking plate inner and rear body side welt. Refer to
INT-19, "Removal and Installation"
.
2.
Remove rear seat cushion fixing bolts. Refer to
SE-116, "Removal and Installation"
.
3.
Remove luggage rear plate.
4.
Remove the luggage side finisher upper.
22. Rear plate ornament (LH)
23. Luggage rear plate cap
24. Trunk net hook
: Clip
: Pawl
: Metal clip
: Vehicle front
JMJIA1408ZZ
JMJIA1387ZZ
Revision: 2008 October
2009 Murano
LUGGAGE FLOOR TRIM
INT-35
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
5.
Disengage rope hook mounting bolt caps, and remove rope
hook mounting bolts with socket wrench (A), and then remove
rope hooks (1) (LH/RH).
6.
Remove the rear seatback control lever escutcheon (LH/RH). Refer to
.
7.
Remove luggage side finisher lower fixing clips with remover tool.
8.
Pull the luggage side finisher lower (1) to disengage the clips
and metal clips, then disconnect the luggage room power socket
harness connector (A).
9.
Remove luggage side finisher lower.
LUGGAGE REAR PLATE
1.
Remove back door weather strip.
2.
Remove luggage rear plate (1) fixing clips with remover tool.
3.
Hold both sides of luggage rear plate, pull upwards to remove.
4.
After removal, place the luggage rear plate (1) as shown in the
figure, then with a screwdriver (A) remove the luggage rear plate
cap fixing bolts (B) and then remove the cap.
5.
Remove the rear plate ornament (2) from the rear plate (1) as shown in the figure below.
JMJIA0617ZZ
JMJIA1398ZZ
: Clip
JMJIA1400ZZ
JMJIA1406ZZ
Revision: 2008 October
2009 Murano
INT-36
< ON-VEHICLE REPAIR >
LUGGAGE FLOOR TRIM
6.
Remove the bolts located inside the luggage floor spacer and remove luggage floor spacer (LH/RH).
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check that clips, pawls, metal clips are securely fitted in panel holes on body when installing, and then
press them in.
: Clip
JMJIA1407ZZ
Revision: 2008 October
2009 Murano
BACK DOOR TRIM
INT-37
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BACK DOOR TRIM
Exploded View
INFOID:0000000003443025
Removal and Installation
INFOID:0000000003443026
REMOVAL
BACK DOOR FINISHER INNER
1.
Fully open back door.
2.
Disengage pull handle finisher (1) fixing pawls with remover tool
(A) and then remove pull handle finisher.
1.
Auto power back door switch finisher 2.
Back door finisher inner
3.
Pull handle finisher
4.
Back door finisher lid
5.
Back door assembly
6.
Back door plate
7.
Back door hinge cover
: Clip
: Pawl
: Metal clip
JMJIA1382ZZ
: Pawl
JMJIA0621ZZ
Revision: 2008 October
2009 Murano
INT-38
< ON-VEHICLE REPAIR >
BACK DOOR TRIM
3.
Push the clip center with a wrapped flat-blade screwdriver (B)
and then remove clip (A).
4.
Disengage the luggage room lamp fixing pawls with a tool, dis-
connect the harness connector (A) then remove the lamp (1)
(LH/RH)
5.
Disengage the back door finisher lid (1) fixing pawls, then
remove the back door finisher lid with remover tool (A).
6.
Remove the auto power back door switch finisher (1) by using a
remover tool (A) and then remove auto power door switch fin-
isher.
7.
Remove the back door finisher inner.
NOTE:
It is strongly recommended to follow the steps below when removing the back door finisher. Failing doing
so may cause the damage of the clips.
JMJIA1018ZZ
JMJIA1385ZZ
: Pawl
JMJIA1384ZZ
: Pawl
JMJIA1383ZZ
Revision: 2008 October
2009 Murano
BACK DOOR TRIM
INT-39
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
1.
Insert remover tool (A) between back door finisher inner (1)
and back door panel to disengage the metal clips (LH/RH).
2.
Insert remover tool (A) between back door finisher inner (1)
and back window glass, pull downwards to disengage clips
as shown in the figure.
3.
Insert remover tool (A) between back door lower finisher
inner (1) and back door panel to disengage the clips.
NOTE:
Starting from the lower downwards and works around the
edges and up to the sides.
8.
Pull out to remove back door finisher inner.
9.
Disengage back door plate (1) fixing pawls and metal clips with
remover tool (A) and then remove back door plate.
: Metal clip
JMJIA1673ZZ
: Clip
: Metal clip
JMJIA1674ZZ
: Clip
JMJIA0622ZZ
: Pawl
: Metal clip
JMJIA1691ZZ
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст