Nissan Murano Z51 (2008 year). Manual — part 265
MIR-56
< SYMPTOM DIAGNOSIS >
[WITH ADP]
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Diagnostic Worksheet
INFOID:0000000004757248
PIIB8740E
Revision: 2008 October
2009 Murano
SQUEAK AND RATTLE TROUBLE DIAGNOSES
MIR-57
< SYMPTOM DIAGNOSIS >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
PIIB8742E
Revision: 2008 October
2009 Murano
MIR-58
< PRECAUTION >
[WITH ADP]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000004778631
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors while ignition switch is
ON or engine is running, never use air or electric power tools or strike near the sensor(s) with a hammer.
Heavy vibration may activate the sensor(s), deploy the airbag(s), possibly cause serious injury.
When using air or electric power tools or hammers, always turn OFF ignition switch, disconnect the battery,
and wait 3 minutes or more before performing any service.
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
INFOID:0000000004778632
NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4.
Perform the necessary repair operation.
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT-III.
Revision: 2008 October
2009 Murano
PRECAUTIONS
MIR-59
< PRECAUTION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
Precaution for Procedure without Cowl Top Cover
INFOID:0000000004778633
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
Precaution for Work
INFOID:0000000003544507
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operation.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
PIIB3706J
Revision: 2008 October
2009 Murano
MIR-60
< PREPARATION >
[WITH ADP]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000004757253
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000004757254
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-43980)
NISSAN Squeak and Rat-
tle Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes the clips, pawls, and metal clips
Power tool
SIIA0995E
JMKIA3050ZZ
PIIB1407E
Revision: 2008 October
2009 Murano
INSIDE MIRROR
MIR-61
< ON-VEHICLE REPAIR >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
ON-VEHICLE REPAIR
INSIDE MIRROR
Exploded View
INFOID:0000000003459056
Removal and Installation
INFOID:0000000003459057
CAUTION:
Never reuse the inside mirror disassembled from mirror base.
REMOVAL
1.
Remove the inside mirror cover.
2.
Remove TORX bolt.
3.
Slide the inside mirror upward to remove.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When inserting the inside mirror into the mirror base, be sure to push the pawl until it get connected to
the mirror base.
1.
Inside mirror
2.
Inside mirror cover
3.
Mirror base
4.
TORX bolt
for symbols in the figure.
JMLIA0136GB
Revision: 2008 October
2009 Murano
MIR-62
< ON-VEHICLE REPAIR >
[WITH ADP]
OUTSIDE MIRROR
OUTSIDE MIRROR
DOOR MIRROR ASSEMBLY
DOOR MIRROR ASSEMBLY : Exploded View
INFOID:0000000003459058
REMOVAL
DISASSEMBLY
1.
Door mirror assembly
2.
Front door assembly
3.
Door mirror corner cover
: Clip
JMLIA0122ZZ
JMLIA0123ZZ
Revision: 2008 October
2009 Murano
OUTSIDE MIRROR
MIR-63
< ON-VEHICLE REPAIR >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
DOOR MIRROR ASSEMBLY : Removal and Installation
INFOID:0000000003459059
CAUTION:
Never damage the mirror bodies.
REMOVAL
1.
Remove the front door finisher. Refer to
INT-11, "FRONT DOOR FINISHER : Removal and Installation"
.
2.
Remove the door mirror corner cover.
3.
Disconnect the door mirror harness connector.
4.
Remove the door mirror mounting nuts, and remove the door mirror assembly.
INSTALLATION
Install in the reverse order of removal.
GLASS MIRROR
GLASS MIRROR : Exploded View
INFOID:0000000003459060
GLASS MIRROR : Disassembly and Assembly
INFOID:0000000003459061
CAUTION:
Never damage the mirror bodies.
DISASSEMBLY
1.
Door mirror cover
2.
Door mirror assembly
3.
Glass mirror
: Pawl
1.
Door mirror cover
2.
Door mirror assembly
3.
Glass mirror
: Pawl
JMLIA0123ZZ
Revision: 2008 October
2009 Murano
MIR-64
< ON-VEHICLE REPAIR >
[WITH ADP]
OUTSIDE MIRROR
1.
Place the glass mirror upward.
2.
Put a strip of protective tape (A) on the housing.
3.
Insert flat-bladed screwdriver (B) into the recess at lower side
between glass mirror (1) and actuator (2), and push up pawls to
remove glass mirror lower side.
NOTE:
Insert a small slotted screwdriver into recess, and push up while
rotating (twist) to make work easier.
4.
Insert flat-bladed screwdriver at RH/LH side between glass mirror and actuator, and push up pawls to
remove glass mirror RH/LH side.
NOTE:
Insert flat-bladed screwdriver into recesses, and push up while rotating (twist) to make work easier.
5.
Remove two terminals of mirror heater attachment. (With heater mirror model)
6.
Pull glass mirror as shown in the figure in order to disengage
both upper pawls, and then remove glass mirror.
ASSEMBLY
Install in the reverse order of removal.
CAUTION:
After installation, visually check that pawls are securely engaged.
DOOR MIRROR COVER
JMLIA0124ZZ
1.
Glass mirror
2.
Actuator
JMLIA0092ZZ
Revision: 2008 October
2009 Murano
OUTSIDE MIRROR
MIR-65
< ON-VEHICLE REPAIR >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
DOOR MIRROR COVER : Exploded View
INFOID:0000000003459066
DOOR MIRROR COVER : Disassembly and Assembly
INFOID:0000000003459063
CAUTION:
Never damage the mirror bodies.
DISASSEMBLY
1.
Remove the glass mirror. Refer to
MIR-63, "GLASS MIRROR : Disassembly and Assembly"
2.
Remove the pawls, and disassemble the door mirror cover from the mirror assembly.
ASSEMBLY
Install in the reverse order of removal.
NOTE:
After installation, visually check that pawls are securely engaged.
1.
Door mirror cover
2.
Door mirror assembly
3.
Glass mirror
: Pawl
JMLIA0123ZZ
Revision: 2008 October
2009 Murano
MIR-66
< ON-VEHICLE REPAIR >
[WITH ADP]
DOOR MIRROR REMOTE CONTROL SWITCH
DOOR MIRROR REMOTE CONTROL SWITCH
Exploded View
INFOID:0000000003554756
INT-11, "FRONT DOOR FINISHER : Exploded View"
Removal and Installation
INFOID:0000000003554757
REMOVAL
1.
Remove the power window main switch finisher (2). Refer to
PWC-114, "Removal and Installation"
2.
Remove door mirror remote control switch (1) from power win-
dow main switch finisher (2) using flat-bladed screwdriver (A).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMLIA0118ZZ
Revision: 2008 October
2009 Murano
DOOR MIRROR SYSTEM
MIR-67
< FUNCTION DIAGNOSIS >
[WITHOUT ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
FUNCTION DIAGNOSIS
DOOR MIRROR SYSTEM
Component Description
INFOID:0000000003554782
Component
Function
Door mirror remote control switch
It supplies power to mirror motor through mirror switch and changeover
switch.
Door mirror
It makes mirror face operate from side to side and up and down with the
mirror control switch operation.
Revision: 2008 October
2009 Murano
MIR-68
< FUNCTION DIAGNOSIS >
[WITHOUT ADP]
INSIDE MIRROR SYSTEM
INSIDE MIRROR SYSTEM
System Description
INFOID:0000000003554783
The sensor built in inside mirror detects the headlight of the vehicle behind and automatically changes the light
transmission to decrease the brightness.
Component Description
INFOID:0000000003554784
Component
Function
Auto anti-dazzling inside mirror
It automatically changes the light transmittance according to the brightness of the
light from the headlight of the vehicle behind.
Revision: 2008 October
2009 Murano
DOOR MIRROR
MIR-69
< COMPONENT DIAGNOSIS >
[WITHOUT ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
COMPONENT DIAGNOSIS
DOOR MIRROR
Wiring Diagram - DOOR MIRROR SYSTEM (WITHOUT AUTOMATIC DRIVE POSI-
TIONER) -
INFOID:0000000003554785
JCLWM2740GB
Revision: 2008 October
2009 Murano
MIR-70
< COMPONENT DIAGNOSIS >
[WITHOUT ADP]
DOOR MIRROR
JCLWM2741GB
Revision: 2008 October
2009 Murano
AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM
MIR-71
< COMPONENT DIAGNOSIS >
[WITHOUT ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM
Wiring Diagram - INSIDE MIRROR SYSTEM -
INFOID:0000000004786433
JCLWM2742GB
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст