Nissan Murano Z51 (2008 year). Manual — part 48
AV
CAMERA CONTROL UNIT
AV-541
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
CAMERA CONTROL UNIT
Exploded View
INFOID:0000000003566819
Removal and Installation
INFOID:0000000003566820
REMOVAL
1.
Remove luggage side finisher lower (RH). Refer to
2.
Remove camera control unit screws, disconnect camera control unit connector and remove the camera
control unit.
INSTALLATION
Install in the reverse order of removal.
Adjustment
INFOID:0000000003566821
ADJUSTMENT
There may be a misalignment of possible route line center position of rear view monitor after removing camera
control unit. Therefore, correct neutral position with the following procedure.
1.
Steer the steering wheel to the leftmost and rightmost ends.
2.
Drive vehicle at 30 km/h (18.6 MPH) min. speed at least 100 m (328.1 ft).
JPNIA0796ZZ
1.
Camera control unit
Revision: 2008 October
2009 Murano
AV-542
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITHOUT NAVIGATION]
REAR VIEW CAMERA
REAR VIEW CAMERA
Exploded View
INFOID:0000000003566822
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000003566823
REMOVAL
1.
Remove back door finisher inner. Refer to
2.
Remove finisher.
3.
Remove rear view camera screws, disconnect rear view camera connector and remove rear view camera
from back door assembly.
INSTALLATION
Install in the reverse order of removal.
Adjustment
INFOID:0000000003566824
Adjust the guide line position if the guide line position is shifted after installing the rear view camera.
1.
Rear view camera
2.
Finisher
JPNIA0797ZZ
Revision: 2008 October
2009 Murano
AV
REAR VIEW CAMERA
AV-543
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
1.
Draw lines on rearward area of the vehicle passing through the
following points: 200 mm (7.87 in) from both sides of the vehicle,
and 0.5 m (1.64 ft), 1.0 m (3.28 ft) from the rear end of the
bumper.
2.
Set into “Adjust offset of rear view camera” mode of Confirma-
tion / Adjustment mode.
3.
Rotate the center dial, and then select the guiding line pattern so
that its angle is aligned with the correction line of the rear of the
vehicle.
4.
Make fine adjustment to the correction line of the rear of the
vehicle with up/down/left/right switches so that its position is
aligned with the guiding line. Press “OK” switch and record the
adjusted guiding line position to the camera control unit.
CAUTION:
Never operate other function such as pressing BACK while writing index data.
If Confirmation/Adjustment mode does not function in the above procedure, perform one of the
following service to adjust the index again.
• Remove battery for five min. Then reconnect battery.
• Remove camera control unit connector for five min. Then reconnect camera control unit connec-
tor.
SKIB3691E
Selected pattern
: 7
Up/Down adjustment range
:
−
20 – 20
Left/Right adjustment range
:
−
20 – 20
SKIB3689E
Revision: 2008 October
2009 Murano
AV-544
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITHOUT NAVIGATION]
STEERING ANGLE SENSOR
STEERING ANGLE SENSOR
Exploded View
INFOID:0000000003566825
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000003566826
REMOVAL
1.
Remove spiral cable.
2.
Remove steering angle sensor from spiral cable.
INSTALLATION
Install in the reverse order of removal.
JSNIA0135ZZ
1.
Spiral cable
2.
Steering angle sensor
Revision: 2008 October
2009 Murano
AV
ROOF ANTENNA
AV-545
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
ROOF ANTENNA
Exploded View
INFOID:0000000003508017
Removal and Installation
INFOID:0000000003508018
REMOVAL
1.
Remove headlining assembly (rear) to secure work space between vehicle and headlining. Refer to
25, "NORMAL ROOF : Exploded View"
[without sunroof] or
INT-29, "SUNROOF : Exploded View"
[with
sunroof].
2.
Disconnect AM/FM main connector and satellite radio antenna connector.
3.
Remove antenna base & satellite radio nut, and then remove antenna base &satellite radio antenna from
roof panel.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When Antenna base & satellite radio antenna mounting nut tightening torque is loose, be careful
about tightening torque. Antenna sensitivity becomes poor, and when it is excessive, roof panel may
become deformed.
JPNIA0786ZZ
1.
Rod antenna
2.
Antenna bade & satellite radio an-
tenna
Antenna base & satellite ra-
dio antenna mounting nut
: 6.5 N·m (0.66 kg-m, 58 in-lb)
Revision: 2008 October
2009 Murano
AV-546
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITHOUT NAVIGATION]
SATELLITE RADIO TUNER
SATELLITE RADIO TUNER
Exploded View
INFOID:0000000003356870
Removal and Installation
INFOID:0000000003356871
REMOVAL
1.
Remove luggage floor finisher front. Refer to
2.
Remove satellite radio tuner (1) with TEL adapter unit as a sin-
gle unit from the body.
3.
Remove bracket screws, and them remove satellite tuner.
INSTALLATION
Install in the reverse order of removal.
1.
Satellite radio tuner
2.
Bracket LH
3.
TEL adapter unit
4.
Bracket RH
JPNIA0784ZZ
:
Vehicle front
JPNIA0785ZZ
Revision: 2008 October
2009 Murano
AV
TEL ADAPTER UNIT
AV-547
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
TEL ADAPTER UNIT
Exploded View
INFOID:0000000003356888
Removal and Installation
INFOID:0000000003356889
REMOVAL
1.
Remove luggage floor finisher front. Refer to
2.
Remove TEL adapter unit (1) with satellite radio tuner as a sin-
gle unit from the body.
3.
Remove bracket screws, and them remove TEL adapter unit.
INSTALLATION
Install in the reverse order of removal.
1.
Satellite radio tuner
2.
Bracket LH
3.
TEL adapter unit
4.
Bracket RH
JPNIA0784ZZ
JPNIA0805ZZ
Revision: 2008 October
2009 Murano
AV-548
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITHOUT NAVIGATION]
ANTENNA FEEDER (RADIO)
ANTENNA FEEDER (RADIO)
Harness Layout
INFOID:0000000003356890
JPNIA0798GB
Revision: 2008 October
2009 Murano
AV
ANTENNA FEEDER (SATELLITE RADIO)
AV-549
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
ANTENNA FEEDER (SATELLITE RADIO)
Harness Layout
INFOID:0000000003508994
JPNIA0798GB
Revision: 2008 October
2009 Murano
AV-550
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITHOUT NAVIGATION]
ANTENNA FEEDER (TEL)
ANTENNA FEEDER (TEL)
Harness Layout
INFOID:0000000003508995
JPNIA0798GB
Revision: 2008 October
2009 Murano
AV
DIAGNOSIS AND REPAIR WORK FLOW
AV-551
< BASIC INSPECTION >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000003356541
OVERALL SEQUENCE
• Reference 1··· Refer to
AV-589, "CONSULT-III Function (MULTI AV)"
.
• Reference 2··· Refer to
.
• Reference 3··· Refer to
DETAILED FLOW
1.
INTERVIEW AND SYMPTOM CONFIRMATION
Check the malfunction symptoms by performing the following items.
• Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred).
• Check the symptom.
Is the occurring symptom a malfunction?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
DIAGNOSIS WITH CONSULT-III
JSNIA0732GB
Revision: 2008 October
2009 Murano
AV-552
< BASIC INSPECTION >
[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS AND REPAIR WORK FLOW
1.
Connect CONSULT-III and perform a self-diagnosis for “MULTI AV”. Refer to
NOTE:
Skip to step 4 of the diagnosis procedure if “MULTI AV” is not displayed.
2.
Check if any DTC is displayed in the self-diagnosis results.
Is DTC displayed?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
TROUBLE DIAGNOSIS FOR DTC
1.
Check the DTC indicated in the self-diagnosis results.
2.
Perform the relevant diagnosis referring to the DTC Index. Refer to
>> GO TO 5.
4.
TROUBLE DIAGNOSIS FOR SYMPTOMS
Perform the relevant diagnosis referring to the diagnosis chart by symptom. Refer to
.
>> GO TO 5.
5.
ERROR PART REPAIR
1.
Repair or replace the identified malfunctioning parts.
2.
Perform a self-diagnosis for “MULTI AV” with CONSULT-III.
NOTE:
Erase the stored self-diagnosis results after repairing or replacing the relevant components if any DTC
has been indicated in the self-diagnosis results.
3.
Check that the symptom does not occur.
Does the symptom occur?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2008 October
2009 Murano
AV
INSPECTION AND ADJUSTMENT
AV-553
< BASIC INSPECTION >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : De-
scription
INFOID:0000000003356542
Always correct the center position of the rear view monitor's possible route line after disconnecting the battery
negative terminal.
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement
INFOID:0000000003356543
1.
CORRECTION OF CENTER POSITION OF REAR VIEW MONITOR'S POSSIBLE ROUTE LINE
Refer to the following for details.
>> Refer to
AV-553, "REAR VIEW MONITOR POSSIBLE ROUTE LINE CENTER POSITION
ADJUSTMENT : Special Repair Requirement"
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000003356544
When camera control unit is replaced, the center position of rear view monitor possible route line is corrected.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000003356545
1.
CORRECTION OF CENTER POSITION OF REAR VIEW MONITOR'S POSSIBLE ROUTE LINE
Refer to the following for details.
>> Refer to
AV-553, "REAR VIEW MONITOR POSSIBLE ROUTE LINE CENTER POSITION
ADJUSTMENT : Special Repair Requirement"
REAR VIEW MONITOR POSSIBLE ROUTE LINE CENTER POSITION ADJUST-
MENT
REAR VIEW MONITOR POSSIBLE ROUTE LINE CENTER POSITION ADJUST-
MENT : Description
INFOID:0000000003356546
Adjust the center position of the possible route line of the rear view monitor if it is shifted.
REAR VIEW MONITOR POSSIBLE ROUTE LINE CENTER POSITION ADJUST-
MENT : Special Repair Requirement
INFOID:0000000003356547
1.
STEERING OPERATION
Steer the steering wheel to the leftmost and rightmost positions.
>> GO TO 2
2.
DRIVING
Drive the vehicle straight ahead 100 m (328.1 ft) or more at a speed of 30 km/h (18.6 MPH) or more.
>> END
Revision: 2008 October
2009 Murano
AV-554
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
MULTI AV SYSTEM
FUNCTION DIAGNOSIS
MULTI AV SYSTEM
System Diagram
INFOID:0000000003356548
NOTE:
• Woofer, illustrated in the above figure, integrates two woofers and a woofer amp.
• In this section, PRESET SWITCH and MULTIFUNCTION SWITCH are written as the MULTIFUNCTION
SWITCH.
JSNIA1070GB
Revision: 2008 October
2009 Murano
AV
MULTI AV SYSTEM
AV-555
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
• An antenna base integrated with radio antenna amp. and satellite
radio antenna is adopted.
System Description
INFOID:0000000003356549
MULTI AV system means that the following systems are integrated.
• AV control unit function by transmitting/receiving data one by one with each unit (slave unit) that configures
them completely as a master unit by connecting between units that configure MULTI AV system with two AV
communication lines (H, L).
• Two AV communication lines (H, L) adopt a twisted pair line that is resistant to noise.
• AV control unit is connected by CAN communication, and it receives data signal from ECM, combination
meter. It computes and displays fuel economy information value with the obtained information. Transmitting/
receiving of data signal is performed by BCM. Also, it transmits the required signal of vehicle setting and
receives the response signal.
• AV control unit is connected with front display unit and serial communication, and it transmits the required
signal of display and display control and receives the response signal from front display unit.
NOTE:
AV control unit can perform CONSULT-III self-operating function and on board self-diagnosis.
• CONSULT-III self diagnosis: Refer to
AV-589, "CONSULT-III Function (MULTI AV)"
• On board self diagnosis: Refer to
AV-575, "Diagnosis Description"
AUXILIARY INPUT SYSTEM
• Image and sound can be output from an external device by connecting a device with auxiliary input jacks.
• Operation can be performed with multifunction switch and steering switch. Multifunction switch transmits
operation signal to AV control unit by AV communication.
• The AUX image signal is input from the auxiliary input jacks to the front display unit.
JSNIA1062GB
System name
System explanation
NAVIGATION SYSTEM
AUDIO SYSTEM
REAR VIEW MONITOR SYSTEM
HANDS-FREE PHONE SYSTEM
VEHICLE INFORMATION SYSTEM
• Status of audio, climate control system, fuel economy, mainte-
nance and navigation is displayed.
• AV control unit displays the fuel consumption status while re-
ceiving data signal through CAN communication from ECM and
combination meter.
• AV control unit is connected to BCM via CAN communication
transmitting/receiving for the vehicle settings function.
AUXILIARY INPUT SYSTEM
Refer to the following “AUXILIARY INPUT SYSTEM”.
VOICE RECOGNITION SYSTEM
Refer to the following “VOICE RECOGNITION SYSTEM”.
TOUCH PANEL SYSTEM
Refer to the following “TOUCH PANEL SYSTEM”.
Revision: 2008 October
2009 Murano
AV-556
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
MULTI AV SYSTEM
• The AUX sound signal is input from the auxiliary input jacks to the AV control unit. The AV control unit out-
puts the AUX sound signal to the BOSE amp. The BOSE amp. outputs the AUX sound signal to woofer and
each speaker.
VOICE RECOGNITION SYSTEM
• Each operation of multi AV system can be performed by inputting sound in to a microphone.
• Start of sound recognition system can be performed by steering switch.
TOUCH PANEL SYSTEM
Each operation of multi AV system can be performed by directly touching the appropriate display.
JSNIA1091GB
JSNIA1092GB
JSNIA0904GB
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст