Nissan Murano Z51 (2008 year). Manual — part 50
AV
HANDS-FREE PHONE SYSTEM
AV-573
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Component Parts Location
INFOID:0000000003464480
1.
Center speaker
2.
Front squawker LH
3.
Front door speaker LH
4.
Rear door speaker LH
5.
Rear speaker LH
6.
BOSE amp.
7.
Woofer
8.
Rear view camera
9.
Camera control unit
10. Rear speaker RH
11.
Antenna base (antenna amp. and
satellite antenna)
12. Rear door speaker RH
13. Front door speaker RH
14. Front squawker RH
15. Microphone
16. GPS antenna
17. Steering angle sensor
18. Steering switch
19. Auxiliary input jacks
20. iPod connector
21. iPod adapter
22. Preset switch
23. AV control unit
24. Multifunction switch
25. Front display unit
A.
Luggage floor finisher is removed
condition
B.
Luggage side finisher lower RH is re-
moved condition
C.
Combination meter is removed condi-
tion
D.
Spiral cable part
E.
Console finisher is removed condition
JSNIA1096ZZ
Revision: 2008 October
2009 Murano
AV-574
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
HANDS-FREE PHONE SYSTEM
Component Description
INFOID:0000000003451238
Part name
Description
AV CONTROL UNIT
• It includes the TEL adapter and Bluetooth
™
function.
• It outputs the TEL voice signal and voice guidance sound signal to the BOSE
amp.
FRONT DISPLAY UNIT
• Display image is controlled by the serial communication from AV control unit.
• Inputs RGB image signal (RGB, RGB area and RGB synchronizing) from AV
control unit and displays the status of hands free phone system.
BOSE AMP.
Inputs TEL voice signal or voice guidance signal from AV control unit and outputs
it to front speaker.
FRONT DOOR SPEAKER
Outputs the TEL voice signal or voice guidance signal from BOSE amp.
PRESET SWITCH
• Adjust the sound when using TEL.
• The operation signal is transmitted to the AV control unit via AV communica-
tion.
STEERING SWITCH
• The hands free-phone system can be operated.
• Steering switch signal (operation signal) is output to AV control unit.
MICROPHONE
• Uses when operating the hands-free phone.
• Outputs Mic. signal (TEL voice signal) to the AV control unit.
• The power (Mic. power supply) is supplied from the AV control unit.
Revision: 2008 October
2009 Murano
AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-575
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Diagnosis Description
INFOID:0000000003356564
MULTIFUNCTION SWITCH AND PRESET SWITCH SELF-DIAGNOSIS FUNCTION
The ON/OFF operation (continuity) of each switch in the multifunction switch and preset switch can be
checked.
Self-diagnosis Mode
• Press the “BACK” switch and the “
” switch of the 8-direction
switches within 10 seconds after turning the ignition switch from
OFF to ACC and hold them for 3 seconds or more. Then the
buzzer sounds, all indicators of the preset switch illuminate, and
the self-diagnosis mode starts.
• The continuity of each switch at the ON position can be checked
by pressing the switch. The buzzer sounds if the switch is normal.
NOTE:
The disk eject switch cannot be checked.
Finishing Self-diagnosis Mode
Self-diagnosis mode is canceled when turning the ignition switch OFF.
MULTI AV SYSTEM ON BOARD DIAGNOSIS FUNCTION
• The AV control unit diagnosis function starts up with multifunction switch operation and the AV control unit
performs a diagnosis for each unit in the system during the on board diagnosis.
• Perform a CONSULT-III diagnosis if the on board diagnosis does not start, e.g., the screen does not display
anything, the multifunction switch does not function, etc.
ON BOARD DIAGNOSIS
Description
• The trouble diagnosis function has a self-diagnosis mode for conducting trouble diagnosis automatically and
a confirmation/adjustment mode for operating manually.
• The self-diagnosis mode performs diagnoses on the AV control unit, connections between system compo-
nents as well as connections between AV control unit and GPS antenna and between AV control unit and
satellite radio antenna. Then it displays the diagnosis results on the display.
• The confirmation/adjustment mode allows the technician to check, modify or adjust the vehicle signals and
set values, as well as to monitor the system error records and system communication status. The checking,
modifying or adjusting generally require human intervention and judgment (the system cannot automati-
cally).
On Board Diagnosis Item
JSNIA1074GB
Mode
Description
Self-Diagnosis
• AV control unit diagnosis
• Diagnoses the connections across system components, between AV
control unit and GPS antenna and between AV control unit and satel-
lite radio antenna.
Revision: 2008 October
2009 Murano
AV-576
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
NOTE:
*: On-board self-diagnosis is not supported. Only CONSULT-III is supported.
STARTING PROCEDURE
1.
Start the engine.
2.
Turn the audio system OFF.
3.
While pressing the “SETTING” button, turn the volume control
dial clockwise or counterclockwise for 40 clicks or more. (When
the self-diagnosis mode is started, a short beep will be heard.)
• Shifting from current screen to previous screen is performed
by pressing the “BACK” button.
Confirmation/
Adjustment
Display Diagnosis
The following check functions are available: color tone check by color
bar display, light and shade check by gray scale display and touch panel
calibration response check.
Vehicle Signals
Diagnosis of signals can be performed for vehicle speed, parking brake,
lights, ignition switch, and reverse.
Speaker Test
The connection of a speaker can be confirmed by test tone.
Climate Control
*
Not used.
Navigation
Steering Angle Ad-
justment
When there is a difference between the actual turning angle and the ve-
hicle mark turning angle, it can be adjusted.
Speed Calibration
When there is a difference between the current location mark and the ac-
tual location, it can be adjusted.
XM SAT Subscrip-
tion Status
The XM NavTraffic subscription status can be checked.
Error History
The system malfunction and the frequency when occurring in the past
are displayed. When the malfunctioning item is selected, the time and
place that the selected malfunction last occurred are displayed.
Vehicle CAN Diagnosis
The transmitting/receiving of CAN communication can be monitored.
AV COMM Diagnosis
The communication condition of each unit of MULTI AV system can be
monitored.
Handsfree Phone
The received volume adjustment of hands-free phone, microphone
speaker check, and erase memory can be performed.
Camera Cont.
The signal connected to camera control unit can be checked and the
guiding line position that overlaps rear view camera image can be adjust-
ed.
Bluetooth
The passkey and the device name can be checked and changed.
SAT
Change Channel
Any necessary channels required to receive traffic information from the
satellite radio system can be set.
Change Application
ID
Any application ID'-s required to receive traffic information from the sat-
ellite radio system can be set.
Diag
Not used.
Delete Unit Connection Log
Erase the connection history of unit and error history.
Initialize Settings
Initializes the AV control unit memory.
Mode
Description
JSNIA1075GB
Revision: 2008 October
2009 Murano
AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-577
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
4.
The trouble diagnosis initial screen is displayed, and then the
items of “Self Diagnosis” and “Confirmation/Adjustment” can be
selected.
SELF-DIAGNOSIS MODE
1.
Start the self-diagnosis function and select “Self Diagnosis”.
-
Self-diagnosis subdivision screen is displayed, and the self-
diagnosis mode starts.
-
The bar graph visible on the center of the self-diagnosis subdivi-
sion screen indicates progress of the trouble diagnosis.
2.
Diagnosis results are displayed after the self-diagnosis is com-
pleted. The unit names and the connection lines are color-coded
according to the diagnostic results.
NOTE:
• Only the control unit (AV control unit) is displayed in red.
• The number of units that is displayed on the on board self-diagnosis display
according to equipment.
• Replace AV control unit if “Self-Diagnosis did not run because of a control
unit malfunction” is indicated. The symptom is AV control unit internal error.
Refer to
.
-
If multiple errors occur at the same time for a single unit, the
screen switch colors are determined according to the following
order of priority: red > gray.
JSNIA0061GB
JSNIA0062GB
Diagnosis results
Unit
Con-
nection
line
Normal
Green
Green
Connection malfunction
Gray
Yellow
Unit malfunction
Note
Red
Green
JSNIA0593GB
Revision: 2008 October
2009 Murano
AV-578
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
-
The comments of the self-diagnosis results can be viewed with a
component in the diagnosis result screen.
SELF-DIAGNOSIS RESULTS
• The self-diagnosis mode allows the technician to diagnose the connection in the communication line
between AV control unit and each unit and the internal operation of the AV control unit.
• Because the start condition of diagnosis function is a switch operation, the on board diagnosis function can-
not be started up if any malfunction is detected in the communication circuit between AV control unit and
multifunction switch.
• Check the applicable display at the following table, and then repair the malfunctioning parts.
Self-diagnosis Result Chart
JSNIA0064GB
Diagnosis results
Detection logic
Possible malfunction location / Action
to take
NOTE:
When a control unit malfunction is detected (red in unit
display), connection malfunctions with other connec-
tion unit may be displayed.
Malfunction is detected in AV control
unit power supply and ground circuits.
Check AV control unit power supply
and ground circuits. When detecting
no malfunction in those components,
replace AV control unit.
“Self-Diagnosis did not run because of a control unit
malfunction”
JSNIA0594GB
Revision: 2008 October
2009 Murano
AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-579
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Malfunction is detected in camera-
connection recognition signal circuit.
Camera connection recognition signal
circuit.
GPS antenna connection malfunction
is detected.
GPS antenna.
Satellite radio antenna connection
malfunction is detected.
• Satellite radio antenna feeder.
• Antenna base.
Diagnosis results
Detection logic
Possible malfunction location / Action
to take
JSNIA0596GB
JSNIA0597GB
JSNIA0598GB
Revision: 2008 October
2009 Murano
AV-580
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
NOTE:
The number of units that is displayed on the on board self-diagnosis display according to equipment.
CONFIRMATION/ADJUSTMENT MODE
1.
Start the diagnosis function and select “Confirmation/Adjustment”. The confirmation/adjustment mode
indicates where each item can be checked or adjusted.
2.
Select each switch on the “Confirmation/Adjustment Mode”
screen to display the relevant trouble diagnosis screen. Press
the “BACK” switch to return to the initial Confirmation/Adjust-
ment Mode screen.
When either one of the following items
are detected:
• serial communication circuits be-
tween AV control unit and front dis-
play unit are malfunctioning.
• serial communication signal be-
tween AV control unit and front dis-
play unit is malfunctioning.
Serial communication circuits be-
tween AV control unit and front display
unit.
When either one of the following items
are detected:
• iPod adapter power supply and
ground circuits are malfunctioning.
• AV communication circuits between
multifunction switch and iPod
adapter are malfunctioning.
• AV communication signal between
AV control unit and iPod adapter is
malfunctioning.
• iPod adapter power supply and
ground circuits.
• AV communication circuits between
camera control unit and the junction
of AV control unit and multifunction
switch.
• AV communication circuits between
camera control unit and iPod adapt-
er.
Diagnosis results
Detection logic
Possible malfunction location / Action
to take
JSNIA0599GB
JSNIA0600GB
JSNIA0617GB
Revision: 2008 October
2009 Murano
AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-581
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Display Diagnosis
The tint of the color bar indication is as per the following list if RGB signal error is detected.
Vehicle Signals
A comparison check can be made of each actual vehicle signal and
the signals recognized by the system.
JSNIA0689GB
R (red) signal error
: Light blue (Cyan) tint
G (green) signal error
: Purple (Magenta) tint
B (blue) signal error
: Yellow tint
JSNIA0075GB
Revision: 2008 October
2009 Murano
AV-582
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Speaker Test
Select “SPEAKER DIAGNOSIS” to display the Speaker Diagnosis
screen. Press “START and NEXT” to generate a test tone in a
speaker. Press “Start” to generate a test tone in the next speaker.
Press “End” to stop the test tones.
NOTE:
The frequency of test tone emitted from each speaker is as follows.
Climate Control
On-board self-diagnosis is not supported. Only CONSULT-III is supported.
Refer to
HAC-157, "CONSULT-III Function"
[with 7 inch display].
Navigation
STEERING ANGLE ADJUSTMENT
The steering angle output value detected with the gyroscope is
adjusted.
SPEED CALIBRATION
Diagnosis item
Display
Vehicle status
Remarks
Vehicle speed
ON
Vehicle speed > 0 km/h (0 MPH)
Changes in indication may be delayed. This is normal.
OFF
Vehicle speed = 0 km/h (0 MPH)
Parking brake
ON
Parking brake is applied.
OFF
Parking brake is released.
Lights
ON
Light switch ON
—
OFF
Light switch OFF
Ignition
ON
Ignition switch ON
—
OFF
Ignition switch in the ACC position
Reverse
ON
Shift the selector lever to the “R”
position
Changes in indication may be delayed. This is normal.
OFF
Shift the selector lever to a position
other than the “R” position
Tweeter
: 3 kHz
Front speaker
: 300 Hz
Rear speaker
: 1 kHz
JSNIA0076GB
JSNIA0077GB
Revision: 2008 October
2009 Murano
AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-583
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
During normal driving, distance error caused by tire wear and tire
pressure change is automatically adjusted for by the automatic dis-
tance correction function. This function, on the other hand, is for
immediate adjustment, in cases such as driving with tire chain fitted
on tires.
XM SAT SUBSCRIPTION STATUS
The XM NavTraffic subscription status can be checked.
Error History
The self-diagnosis results are judged depending on whether any error occurs from when “Self-diagnosis” is
selected until the self-diagnosis results are displayed.
However, the diagnosis results are judged normal if an error has occurred before the ignition switch is turned
ON and then no error has occurred until the self-diagnosis start. Check the “Error Record” to detect any error
that may have occurred before the self-diagnosis start because of this situation.
The error record displays the time and place of the most recent occurrence of that error. However, take note of
the following points.
• If there is a malfunction with the GPS antenna circuit board in the AV control unit, the correct date and time
of occurrence may not be able to be displayed.
• Place of the error occurrence is represented by the position of the current location mark at the time the error
occurred. If the current location mark has deviated from the correct position, then the place of the error
occurrence cannot be correctly located.
• The frequency of occurrence is displayed in a count up manner. The actual count up method differs depend-
ing on the error item.
Count up method A
• The counter resets to 0 if an error occurs when IGN switch is turned ON. The counter increases by 1 if the
condition is normal at a next IGN ON cycle.
• The counter upper limit is 39. Any counts exceeding 39 are ignored. The counter can be reset (no error
record display) with the “Delete log” switch or CONSULT-III.
Count up method B
• The counter increases by 1 if an error occurs when IGN switched is ON. The counter will not decrease even
if the status is normal at the next IGN ON cycle.
• The counter upper limit is 50. Any counts exceeding 50 are ignored. The counter can be reset (no error
record display) with the “Delete log” switch or CONSULT-III.
JSNIA0078GB
JSNIA0089GB
Display type of occur-
rence frequency
Error history display item
Count up method A
CAN communication line, control unit (CAN), AV communication line, control unit (AV communication)
Count up method B
Other than the above
Revision: 2008 October
2009 Murano
AV-584
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Error item
Some error items may be displayed simultaneously according to the cause. If some error items are displayed
simultaneously, the detection of the cause can be performed by the combination of display items
JSNIA0079GB
Error item
Description
Possible malfunction factor/Action to take
CAN COMM CIRCUIT
CAN communication malfunction is detect-
ed.
Perform diagnosis with CONSULT-III, and
then repair the malfunctioning parts accord-
ing to the diagnosis results.
Refer to
CONTROL UNIT (CAN)
CAN initial diagnosis malfunction is detect-
ed.
Replace the AV control unit.
CONTROL UNIT (AV)
AV communication circuit initial diagnosis
malfunction is detected.
FLASH-ROM Error Of Control Unit
AV control unit malfunction is detected.
Connection Of Gyro
XM SERIAL COMM Error
CAN Controller Memory Error
Bluetooth Module Connection Error
HDD CONN Error
HDD READ Error
HDD WRITE Error
HDD COMM Error
HDD ACCESS Error
DSP CONN Error
DSP COMM Error
Internal Communication Error
Malfunction is detected in AV control unit
power supply and ground circuits.
Check AV control unit power supply and
ground circuits. When detecting no mal-
function in those components, replace AV
control unit.
GPS Communication Error
GPS malfunction is detected.
An intermittent error caused by strong radio
interference may be detected unless a
symptom (GPS reception error, etc.) oc-
curs.
Replace the AV control unit if the malfunc-
tion occurs constantly.
GPS ROM Error
GPS RAM Error
GPS RTC Error
Revision: 2008 October
2009 Murano
AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-585
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Front Display Connection Error
When either one of the following items are
detected:
• front display unit power supply and
ground circuits are malfunctioning.
• serial communication circuits between
AV control unit and front display unit are
malfunctioning.
• serial communication signal between AV
control unit and front display unit is mal-
functioning.
• Front display unit power supply and
ground circuits.
• Serial communication circuits between
AV control unit and display unit.
GPS Antenna Error
GPS antenna connection malfunction is de-
tected.
GPS antenna.
Camera Control Unit Connection Error
Malfunction is detected in camera connec-
tion recognition circuit between AV control
unit and camera control unit.
Camera-connection recognition circuit be-
tween AV control unit and camera control
unit.
XM Antenna Connection Error
Satellite radio antenna connection malfunc-
tion is detected.
• Satellite radio antenna feeder.
• Antenna base.
• AV COMM CIRCUIT
• Internal Communication Error
Malfunction is detected in AV control unit
power supply and ground circuits.
Check AV control unit power supply and
ground circuits. When detecting no mal-
function in those components, replace AV
control unit.
• AV COMM CIRCUIT
• Switches Connection Error
When either one of the following items are
detected:
• multifunction switch power supply and
ground circuits are malfunctioning.
• AV communication circuits between AV
control unit and multifunction switch are
malfunctioning.
• AV communication signal between AV
control unit and multifunction switch is
malfunctioning.
• Multifunction switch power supply and
ground circuits.
• AV communication circuits between AV
control unit and multifunction switch.
• AV COMM CIRCUIT
• Rearview Camera Connection Error
When either one of the following items are
detected:
• camera control unit power supply and
ground circuits are malfunctioning.
• AV communication circuits between mul-
tifunction switch and camera control unit
is malfunctioning.
• AV communication signal between AV
control unit and camera control unit is
malfunctioning.
• Camera control unit power supply and
ground circuits.
• AV communication circuits between mul-
tifunction switch and camera control unit.
• AV COMM CIRCUIT
• iPod Connection Error
When either one of the following items are
detected:
• iPod adapter power supply and ground
circuits are malfunctioning.
• AV communication circuits between mul-
tifunction switch and iPod adapter are
malfunctioning.
• AV communication signal between AV
control unit and iPod adapter is malfunc-
tioning.
• iPod adapter power supply and ground
circuits.
• AV communication circuits between mul-
tifunction switch unit and iPod adapter.
• AV COMM CIRCUIT
• Rearview Camera Connection Error
• iPod Connection Error
*
Malfunction is detected in AV communica-
tion circuits between camera control unit
and the junction of AV control unit and mul-
tifunction switch.
AV communication circuits between cam-
era control unit and the junction of AV con-
trol unit and multifunction switch.
Error item
Description
Possible malfunction factor/Action to take
Revision: 2008 October
2009 Murano
AV-586
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
NOTE:
*: Non-equipped item is not displayed.
Vehicle CAN Diagnosis
• CAN communication status and error counter is displayed.
• The error counter displays “OK” if any malfunction was not
detected in the past and displays “0” if a malfunction is detected. It
increases by 1 if the status is normal at the next ignition switch ON
cycle. The upper limit of the counter is 39.
• The error counter is erased if “Reset” is pressed.
AV COMM Diagnosis
• Displays the communication status between AV control unit (mas-
ter unit) and each unit.
• The error counter displays “OK” if any malfunction was not
detected in the past and displays “0” if a malfunction is detected. It
increases by 1 if the condition is normal at the next ignition switch
ON cycle. The upper limit of the counter is 39.
• The error counter is erased if “Reset” is pressed.
NOTE:
• Any units with “—” displayed have no history of vehicle connection.
• AV COMM CIRCUIT
• Switches Connection Error
• Rearview Camera Connection Error
• iPod Connection Error
*
Malfunction is detected in AV communica-
tion circuits between AV control unit and
multifunction switch.
AV communication circuits between AV
control unit and the junction of camera con-
trol unit and multifunction switch.
• AV COMM CIRCUIT
• Internal Communication Error
• Switches Connection Error
• Rearview Camera Connection Error
• iPod Connection Error
*
Malfunction is detected in AV communica-
tion circuits.
Check and repair the short circuit in AV
communication circuits.
Error item
Description
Possible malfunction factor/Action to take
Items
Display (Current)
Malfunction counter
(Past)
Tx (HVAC)
OK / UNKWN
OK / 0 – 39
Rx (ECM)
OK / UNKWN
OK / 0 – 39
Rx (Cluster)
OK / UNKWN
OK / 0 – 39
Rx (BCM)
OK / UNKWN
OK / 0 – 39
Rx (HVAC)
OK / UNKWN
OK / 0 – 39
Rx (USM)
OK / UNKWN
OK / 0 – 39
JSNIA0080GB
Items
Status
(Current)
Counter
(Past)
C Tx(ITM–PrimarySW)
OK / UNKWN
OK / 0 – 39
C Rx(PrimarySW–ITM)
OK / UNKWN
OK / 0 – 39
C Rx(STRG SW–ITM)
OK / UNKWN
OK / 0 – 39
C Rx (Audio–ITM)
OK / UNKWN
OK / 0 – 39
C Rx(Amp–ITM)
OK / UNKWN
OK / 0 – 39
C Rx(RearCamera–ITM)
OK / UNKWN
OK / 0 – 39
C Rx(XM–ITM)
OK / UNKWN
OK / 0 – 39
C Rx(iPod–ITM)
OK / UNKWN
OK / 0 – 39
C Rx(Amp–Audio)
—
—
C Rx(iPod–Audio)
OK / UNKWN
OK / 0 – 39
C Tx(Audio–ITM)
OK / UNKWN
OK / 0 – 39
JSNIA0081GB
Revision: 2008 October
2009 Murano
AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-587
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
• “Audio” and “Amp” indicate the same status because “Amp” indicates the status of the amplifier integrated in the AV control unit.
• “STRG SW”, “Amp”“XM” indicate the same status as “Audio”.
Hands-Free Phone
The hands-free phone reception volume adjustment, microphone
and speaker test, and memory erase functions are also available.
Camera Cont.
The two functions of “Connection Confirmation” and “Adjust Offset of Rear View Camera” are available.
CONNECTION CONFIRMATION
The steering angle sensor, reverse signal and vehicle speed sensor
can be inspected.
ADJUST OFFSET OF REAR VIEW CAMERA
JSNIA0083GB
JSNIA0084GB
Diagnosis item
Display
Vehicle status
Steer. Angle Sensor
ON
When steering the vehicle with ignition switch ON (remains ON until connection
mode is stopped when it is turned ON)
OFF
• Ignition switch at ACC
• No steering with ignition switch ON
—
Malfunction detected in camera connection recognition signal
Reverse Sensor
ON
Selector lever is in “R” with ignition switch ON.
OFF
• Ignition switch at ACC
• Selector lever is in position other than “R” with ignition switch ON.
—
Malfunction detected in camera-connection recognition signal
Vehicle Speed Sensor
ON
Vehicle speed is more than 0 km/h (0 MPH) with ignition switch ON
OFF
• Ignition switch at ACC
• Vehicle speed is 0 km/h (0 MPH) with ignition switch ON
—
Malfunction detected in camera connection recognition signal
Side view Switch
—
Not used
Revision: 2008 October
2009 Murano
AV-588
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Use this mode to adjust the guide line display position of the rear-
view monitor if necessary after removing the rear view monitor cam-
era.
Bluetooth
Confirm / Change Passkey
• The Bluetooth passkey can be confirmed and changed.
• The passkey can be changed by four digits within 0 to 9.
Confirm / Change Device Name
• The Bluetooth device name be confirmed and changed.
• The device name can be changed by sixteen digits from A to Z
(small characters can be used) and “-” (hyphens).
SAT
• Change Channel
- Any necessary channels required to receive traffic information from
the satellite radio system can be set.
JSNIA0085GB
JSNIA0086GB
JSNIA0087GB
JSNIA0092GB
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст