Nissan Pathfinder (2010 year). Manual — part 212
PREPARATION
DLN-269
< PREPARATION >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
KV40104830
(
—
)
Drift
• Installing input oil seal
a: 70 mm (2.76 in) dia.
b: 63.5 mm (2.50 in) dia.
ST35300000
(
—
)
Drift
• Removing carrier bearing
• Installing metal bushing
• Removing front bearing
a: 59 mm (2.32 in) dia.
b: 45 mm (1.77 in) dia.
ST30021000
(J-22912-01)
Puller
• Removing carrier bearing
• Removing front bearing
• Removing rear bearing
ST33710000
(
—
)
Drift
• Removing needle bearing
• Removing metal bushing
• Removing rear bearing
a: 89 mm (3.5 in)
b: 30 mm (1.18 in) dia.
c: 24 mm (0.94 in) dia.
ST35325000
(
—
)
Drift bar
• Removing metal bushing
a: 215 mm (8.46 in)
b: 25 mm (0.98 in) dia.
c: M12
×
1.5P
ST33220000
(
—
)
Drift
• Installing needle bearing
a: 37 mm (1.46 in) dia.
b: 31 mm (1.22 in) dia.
c: 22 mm (0.87 in) dia.
Tool number
(Kent-Moore No.)
Tool name
Description
ZZA1003D
NT073
ZZA0537D
ZZA1057D
NT663
ZZA1046D
2010 Pathfinder
DLN-270
< PREPARATION >
[TRANSFER: TX15B]
PREPARATION
Commercial Service Tool
INFOID:0000000005258434
ST27863000
(
—
)
Drift
• Installing carrier bearing
a: 75 mm (2.95 in) dia.
b: 62 mm (2.44 in) dia.
ST30901000
(J-26010-01)
Drift
• Installing rear bearing
• Installing front bearing
a: 79 mm (3.11 in) dia.
b: 45 mm (1.77 in) dia.
c: 35.2 mm (1.38 in) dia.
Tool number
(Kent-Moore No.)
Tool name
Description
ZZA1003D
ZZA0978D
Tool name
Description
Puller
• Removing companion flange
• Removing mainshaft rear bearing
Puller
• Removing mainshaft rear bearing
Pin punch
• Removing retaining pin
a: 6 mm (0.24 in) dia.
Power tool
• Loosening bolts and nuts
NT077
ZZB0823D
NT410
PBIC0190E
2010 Pathfinder
TRANSFER FLUID
DLN-271
< ON-VEHICLE MAINTENANCE >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
ON-VEHICLE MAINTENANCE
TRANSFER FLUID
Replacement
INFOID:0000000005258435
CAUTION:
If using the vehicle for towing, the transfer fluid must be replaced as specified. Refer to
DRAINING
1. Stop engine.
2. Remove the drain plug and gasket and drain the fluid.
3. Install the drain plug with a new gasket to the transfer. Tighten to
the specified torque. Refer to
CAUTION:
Do not reuse gasket.
FILLING
1. Remove the filler plug and gasket.
2. Fill the transfer with new fluid until the fluid level reaches the
specified limit near the filler plug hole.
CAUTION:
Carefully fill fluid. (Fill up for approx. 3 minutes.)
3. Leave the vehicle for 3 minutes, and check fluid level again.
4. Install the filler plug with a new gasket to the transfer. Tighten to
the specified torque. Refer to
CAUTION:
Do not reuse gasket.
Inspection
INFOID:0000000005258436
CAUTION:
If using the vehicle for towing, the transfer fluid must be replaced as specified. Refer to
FLUID LEAKAGE AND FLUID LEVEL
1. Make sure that fluid is not leaking from the transfer assembly or around it.
2. Check fluid level from the filler plug hole as shown.
CAUTION:
Do not start engine while checking fluid level.
3. Install the filler plug with a new gasket to the transfer. Tighten to
the specified torque. Refer to
CAUTION:
Do not reuse gasket.
SDIA3286E
Fluid grade and capacity : Refer to
SDIA3287E
SDIA3287E
2010 Pathfinder
DLN-272
< ON-VEHICLE REPAIR >
[TRANSFER: TX15B]
TRANSFER CONTROL UNIT
ON-VEHICLE REPAIR
TRANSFER CONTROL UNIT
Removal and Installation
INFOID:0000000005258437
REMOVAL
1. Switch 4WD shift switch to 2WD and set transfer assembly to 2WD.
CAUTION:
When removing transfer control unit, transfer state must be at 2WD.
2. Turn the ignition switch OFF and disconnect negative battery terminal.
3. Remove the lower instrument panel LH. Refer to
IP-12, "Removal and Installation"
.
4. Disconnect the two transfer control unit connectors.
5. Remove the transfer control unit bolts.
6. Remove the transfer control unit.
INSTALLATION
Installation is in the reverse order of removal.
• When installing the transfer control unit, tighten bolts to the specified torque.
• After the installation, check 4WD shift indicator pattern. If NG, adjust position between transfer assembly and
transfer control unit. Refer to
DLN-265, "Precaution for Transfer Assembly and Transfer Control Unit
.
LDIA0168E
Transfer control unit bolts : 3.4 N·m (0.35 kg-m, 30 in-lb)
2010 Pathfinder
FRONT OIL SEAL
DLN-273
< ON-VEHICLE REPAIR >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
FRONT OIL SEAL
Removal and Installation
INFOID:0000000005258438
REMOVAL
1. Partially drain the transfer fluid. Refer to
.
2. Remove the front propeller shaft. Refer to
DLN-315, "Removal and Installation"
.
3. Remove the companion flange self-lock nut using suitable tool.
4. Put a matching mark on top of the front drive shaft in line with
the mark on the companion flange.
CAUTION:
Use paint to make the matching mark on the front drive
shaft. Do not damage the front drive shaft.
5. Remove the companion flange using suitable tool.
6. Remove the front oil seal from the front case using Tool.
CAUTION:
Do not damage front case.
INSTALLATION
LDIA0142E
SDIA2779E
WDIA0193E
Tool number
: ST33290001 (J-34286)
LDIA0144E
2010 Pathfinder
DLN-274
< ON-VEHICLE REPAIR >
[TRANSFER: TX15B]
FRONT OIL SEAL
1. Install the new front oil seal until it is flush with the end face of
the front case using suitable tool.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal.
2. Align the matching mark of the front drive shaft with the match-
ing mark of the companion flange, then install the companion
flange.
3. Install the new self-lock nut and tighten to the specified torque
using suitable tool. Refer to
CAUTION:
Do not reuse self-lock nut.
4. Install the front propeller shaft. Refer to
.
5. Refill the transfer with fluid and check for fluid leakage and fluid
LDIA0145E
SDIA2214E
LDIA0147E
2010 Pathfinder
REAR OIL SEAL
DLN-275
< ON-VEHICLE REPAIR >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REAR OIL SEAL
Removal and Installation
INFOID:0000000005258439
REMOVAL
1. Partially drain the transfer fluid. Refer to
.
2. Remove the rear propeller shaft. Refer to
DLN-325, "Removal and Installation"
3. Remove the dust cover from the rear case.
CAUTION:
Do not damage the rear case.
4. Remove the oil cover from the dust cover.
5. Remove the rear oil seal from the rear case using Tool.
CAUTION:
Do not damage the rear case.
INSTALLATION
1. Install the new rear oil seal until it is flush with the end face of the
rear case using Tool.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal.
2. Install the oil cover until it reaches the end face of the new dust cover.
CAUTION:
Position the oil cover with the notch at bottom position.
WDIA0127E
Tool number
: ST33290001 (J-34286)
LDIA0139E
Tool number
: KV38100500 ( — )
LDIA0140E
2010 Pathfinder
DLN-276
< ON-VEHICLE REPAIR >
[TRANSFER: TX15B]
REAR OIL SEAL
3. Apply petroleum jelly to the circumference of the new dust cover.
Position the new dust cover as shown.
CAUTION:
• Do not reuse dust cover.
• Position the protrusions at the position shown.
• 1: Dust cover
• A: Protrusions
• 2: Rear case assembly
4. Install the new dust cover to the rear case using Tool.
CAUTION:
• Do not reuse dust cover.
• Apply petroleum jelly to dust cover.
5. Install the rear propeller shaft. Refer to
.
6. Refill the transfer with fluid and check for fluid leakage and fluid
AWDIA0550GB
Tool number
: KV40105310 ( — )
PDIA0116E
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст