Nissan Pathfinder (2010 year). Manual — part 213
TRANSFER CONTROL DEVICE
DLN-277
< ON-VEHICLE REPAIR >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
TRANSFER CONTROL DEVICE
Removal and Installation
INFOID:0000000005258440
REMOVAL
1. Switch the 4WD shift switch to 2WD and set the transfer assembly to 2WD.
2. Disconnect the transfer control device connector.
3. Remove the breather hose from the transfer control device.
4. Remove the bolts and detach the transfer control device.
INSTALLATION
1. Install the new O-ring to the transfer control device.
CAUTION:
• Do not reuse O-ring.
• Apply petroleum jelly to O-ring.
2. Install the transfer control device.
a. Turn the control shift rod fully counterclockwise using a suitable
tool, and then put a mark on the control shift rod.
b. Align the transfer control device shaft cutout with the mark on
the control shift rod, and install.
NOTE:
Turn the transfer control device when the transfer control device
connection does not match.
LDIA0136E
SDIA3378E
PDIA0119E
PDIA0120E
2010 Pathfinder
DLN-278
< ON-VEHICLE REPAIR >
[TRANSFER: TX15B]
TRANSFER CONTROL DEVICE
c.
Tighten the bolts to the specified torque. Refer to
3. Install the breather hose to the transfer control device.
4. Connect the transfer control device connector.
5. After the installation, check the 4WD shift indicator pattern. If
NG, adjust the position between the transfer assembly and
transfer control unit. Refer to
DLN-265, "Precaution for Transfer
Assembly and Transfer Control Unit Replacement"
SDIA2212E
2010 Pathfinder
AIR BREATHER HOSE
DLN-279
< ON-VEHICLE REPAIR >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000005258441
CAUTION:
• Make sure there are no pinched or restricted areas on each air breather hose caused by folding or
bending when installing it.
• Install each air breather hose into the breather tube (metal
connector) until the hose end reaches the end of the curved
section. Set each air breather hose with paint mark facing
upward.
- A: Transfer control device air breather hose
- B: A/T air breather hose
- C: Paint marks
- D: Transfer air breather hose
• Install transfer control device air breather hose and transfer
air breather hose on clip A and clip B with the paint mark fac-
ing upward.
1.
Breather tube
2.
Clip A
3.
Clip B
4.
Clip C
5.
Clip D
6.
Breather tube (transfer)
7.
Air breather hose clamp
8.
Transfer control device
SDIA3351E
AWDIA0628GB
SDIA3353E
2010 Pathfinder
DLN-280
< ON-VEHICLE REPAIR >
[TRANSFER: TX15B]
AIR BREATHER HOSE
• Install clip C on transfer control device air breather hose and
transfer air breather hose with the paint mark matched.
• Install transfer control device air breather hose and transfer
air breather hose on clip D with the paint mark facing upward.
• Install transfer air breather hose into the breather tube (trans-
fer, metal connector) until the hose end reaches the base of
the tube. Set transfer air breather hose with paint mark facing
upward.
• Install transfer control device air breather hose into transfer
control device (case connector) until the hose end reaches
the base of the tube. Set transfer control device air breather
hose with paint mark facing forward.
SDIA3354E
SDIA3355E
SDIA3196E
SDIA3300E
2010 Pathfinder
TRANSFER ASSEMBLY
DLN-281
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REMOVAL AND INSTALLATION
TRANSFER ASSEMBLY
Removal and Installation
INFOID:0000000005258442
REMOVAL
1. Switch 4WD shift switch to 2WD and set transfer assembly to 2WD.
2. Remove the undercovers using power tool.
3. Drain the transfer fluid. Refer to
.
4. Remove the center exhaust tube and main muffler. Refer to
EX-7, "Removal and Installation"
.
5. Remove the front and rear propeller shafts. Refer to
DLN-315, "Removal and Installation"
325, "Removal and Installation"
(rear).
CAUTION:
Do not damage spline, sleeve yoke and rear oil seal when removing rear propeller shaft.
NOTE:
Insert a plug into the rear oil seal after removing the rear propeller shaft.
6. Remove the A/T nuts from the A/T crossmember. Refer to
7. Position two suitable jacks under the A/T and transfer assembly.
8. Remove the A/T crossmember. Refer to
.
WARNING:
Support A/T and transfer assembly using two suitable jacks while removing A/T crossmember.
9. Disconnect the electrical connectors from the following:
• ATP switch
• 4LO switch
• Wait detection switch
• Transfer control device
10. Disconnect each air breather hose from the following. Refer to
TM-187, "4WD : Removal and Installation"
.
• Transfer control device
• Breather tube (transfer)
11. Remove the transfer to A/T and A/T to transfer bolts.
12. Remove the transfer assembly.
WARNING:
support transfer assembly with suitable jack while removing it.
CAUTION:
Do not damage rear oil seal (A/T).
INSTALLATION
Installation is in the reverse order of removal.
• Tighten the bolts to specification.
• Fill the transfer with new fluid and check for fluid leakage and fluid
.
• Start the engine for one minute. Then stop the engine and recheck
the transfer fluid. Refer to
• After the installation, check the 4WD shift indicator pattern. If NG,
adjust the position between the transfer assembly and transfer
control unit. Refer to
DLN-265, "Precaution for Transfer Assembly
and Transfer Control Unit Replacement"
.
Tightening torque
: 36 N·m (3.7kg-m, 27 ft-lb)
SMT872C
2010 Pathfinder
DLN-282
< DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
TRANSFER ASSEMBLY
DISASSEMBLY AND ASSEMBLY
TRANSFER ASSEMBLY
Component Parts Location
INFOID:0000000005576393
1.
Baffle plate
2.
Breather tube
3.
Front case
4.
Snap ring
5.
Input oil seal
6.
Self-lock nut
7.
Companion flange
8.
Front oil seal
9.
4LO switch (gray with green
paint)
10. ATP switch (black)
11. Rear case
12. Wait detection switch (gray)
13. Gasket
14. Filler plug
15. Drain plug
16. O-ring
17. Transfer control device
18. Harness bracket
19. Dust cover
20. Oil cover
21. Rear oil seal
22. Air breather hose clamp
23. Retainer bolt
24. Gasket
A.
Apply Genuine Anaerobic Liquid
Gasket or equivalent.
B.
Apply Genuine Silicone RTV or
equivalent.
AWDIA0749GB
2010 Pathfinder
TRANSFER ASSEMBLY
DLN-283
< DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Disassembly and Assembly
INFOID:0000000005258443
COMPONENTS
1.
Input bearing
2.
Snap ring
3.
Internal gear
4.
Carrier bearing
5.
Sun gear
6.
Needle bearing
7.
Metal bushing
8.
Planetary carrier assembly
9.
L-H sleeve
10. Drive chain
11. Mainshaft
12. Sprocket
13. 2-4 sleeve
14. Clutch gear
15. Oil pump assembly
16. Retainer
17. Mainshaft rear bearing
18. Front bearing
19. Front drive shaft
20. Rear bearing
21. L-H shift fork
22. L-H shift rod
23. Retaining pin
24. 2-4 shift bracket
25. 2-4 shift fork
26. Fork guide collar
27. 2-4 shift fork spring
28. Retaining ring
29. Snap ring
30. Shift collar
31. Clevis pin
32. Drum cam
33. Control shift rod
34. Spacer
AWDIA0016GB
2010 Pathfinder
DLN-284
< DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
TRANSFER ASSEMBLY
1.
Baffle plate
2.
Breather tube
3.
Front case
4.
Snap ring
5.
Input oil seal
6.
Self-lock nut
7.
Companion flange
8.
Front oil seal
9.
4LO switch (gray with green
paint)
10. ATP switch (black)
11. Rear case
12. Wait detection switch (gray)
13. Gasket
14. Filler plug
15. Drain plug
16. O-ring
17. Transfer control device
18. Harness bracket
19. Dust cover
20. Oil cover
21. Rear oil seal
22. Air breather hose clamp
23. Retainer bolt
24. Gasket
A.
Apply Genuine Anaerobic Liquid
Gasket or equivalent.
B.
Apply Genuine Silicone RTV or
equivalent.
AWDIA0749GB
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст