Nissan Pathfinder (2010 year). Manual — part 631
TM-176
< ON-VEHICLE REPAIR >
CONTROL VALVE WITH TCM
11. Remove bolts (A), (B) and (C) from control valve with TCM.
12. Remove control valve with TCM from transmission case.
CAUTION:
When removing, be careful with the manual valve notch and
manual plate height. Remove it vertically.
13. Remove the A/T fluid temperature sensor 2 or plug as shown below.
a.
A/T fluid temperature sensor 2
i.
Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
ii.
Remove bracket from A/T fluid temperature sensor 2.
b.
Plug
: Front
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA8074E
SCIA5142E
SCIA5253E
SCIA5264E
2010 Pathfinder
CONTROL VALVE WITH TCM
TM-177
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
i.
Remove plug (1) with bracket (2) from control valve with TCM.
ii.
Remove bracket (1) from plug (2).
iii. Remove O-ring (1) from plug (2).
14. Remove O-ring from A/T assembly harness connector.
15. Disconnect TCM connectors.
CAUTION:
Do not damage connectors.
: Bolt
JSDIA1311ZZ
JSDIA1312ZZ
JSDIA1313ZZ
SCIA5155E
SCIA5447E
2010 Pathfinder
TM-178
< ON-VEHICLE REPAIR >
CONTROL VALVE WITH TCM
16. Remove A/T assembly harness connector from control valve
with TCM using suitable tool.
17. Disconnect TCM connector (1) and transmission range switch
connector (2).
CAUTION:
Do not damage connectors.
INSTALLATION
CAUTION:
• If the A/T fluid temperature sensor 2 has flaws, replace it with a plug.
• After completing installation, check A/T fluid leakage and fluid level. Refer to
1. Connect TCM connector (1) and transmission range switch con-
nector (2).
2. Install A/T assembly harness connector to control valve with
TCM.
SCIA5448E
JSDIA1317ZZ
JSDIA1317ZZ
SCIA5450E
2010 Pathfinder
CONTROL VALVE WITH TCM
TM-179
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3. Connect TCM connector.
4. Install new O-ring in A/T assembly harness connector.
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
5. Install the A/T fluid temperature sensor 2 or plug as shown below.
a.
A/T fluid temperature sensor 2
i.
Install A/T fluid temperature sensor 2 to bracket.
ii.
Install A/T fluid temperature sensor 2 (with bracket) to control
valve with TCM. Tighten A/T fluid temperature sensor 2 bolt to
the specified torque.
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
b.
Plug
NOTE:
• When replacing the A/T fluid temperature sensor 2 with the plug, the A/T fluid temperature sensor 2 con-
nector should not be connected.
• Fold the terminal clips.
SCIA5447E
SCIA5155E
SCIA5264E
SCIA5253E
2010 Pathfinder
TM-180
< ON-VEHICLE REPAIR >
CONTROL VALVE WITH TCM
i.
Install new O-ring (1) in plug (2).
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
• O-ring should be free of contamination.
ii.
Install plug (2) to bracket (1).
iii. Install plug (1) [with bracket (2)] to control valve with TCM.
Tighten plug bolt (
) to the specified torque.
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
6. Install control valve with TCM in transmission case.
CAUTION:
• Make sure that input speed sensor is securely installed
into input speed sensor hole (A).
• Hang down output speed sensor harness toward outside
so as not to disturb installation of control valve with TCM.
• Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
• Assemble it so that manual valve cutout is engaged with
manual plate projection.
JSDIA1313ZZ
JSDIA1312ZZ
JSDIA1311ZZ
1
: Brake band
JSDIA1318ZZ
SCIA5142E
2010 Pathfinder
CONTROL VALVE WITH TCM
TM-181
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
7. Install bolts (A), (B) and (C) in control valve with TCM.
8. Tighten bolt (1), (2) and (3) temporarily to prevent dislocation.
After that tighten them in order (1
→
2
→
3). Then tighten other
bolts. Tighten control valve with TCM bolts to the specified
torque.
9. After installing the A/T fluid temperature sensor 2, connect the A/T fluid temperature sensor 2 connector
as shown below.
a. Connect A/T fluid temperature sensor 2 connector (A).
b. Securely fasten terminal cord assembly and A/T fluid tempera-
ture sensor 2 harness with terminal clips (
).
10. Connect output speed sensor connector (1).
: Front
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA8074E
: Front
Bolt symbol
A
B
C
Number of bolts
5
6
1
Length mm (in)
42 (1.65)
55 (2.17)
40 (1.57)
Tightening torque
N·m (km-g, in-lb)
7.9 (0.81, 70)
With ATF applied
7.9 (0.81, 70)
SCIA8075E
SCIA8124E
JSDIA1319ZZ
2010 Pathfinder
TM-182
< ON-VEHICLE REPAIR >
CONTROL VALVE WITH TCM
11. Securely fasten output speed sensor (1) harness with terminal
clip (
).
12. Install oil pan to transmission case. Refer to
TM-172, "Removal and Installation"
.
13. Pull up A/T assembly harness connector.
CAUTION:
Do not damage connector.
14. Install snap ring to A/T assembly harness connector.
15. Connect A/T assembly harness connector.
16. Connect the negative battery terminal.
17. Refill the A/T with fluid and check the fluid level and for fluid
leakage. Refer to
TM-155, "Checking the A/T Fluid (ATF)"
.
JSDIA1316ZZ
SCIA5038E
SCIA5039E
2010 Pathfinder
REAR OIL SEAL
TM-183
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REAR OIL SEAL
Removal and Installation
INFOID:0000000005258187
REMOVAL
1. Remove rear propeller shaft. Refer to
DLN-325, "Removal and Installation"
2. Remove transfer from transmission (4WD models). Refer to
DLN-151, "Removal and Installation"
(ATX14B),
DLN-281, "Removal and Installation"
(TX15B).
3. Remove rear oil seal using flat bladed screwdriver.
CAUTION:
Do not scratch rear extension assembly (2WD models) or
adapter case assembly (4WD models).
INSTALLATION
1. Install new rear oil seal until it is flush into the rear extension
case (2WD models) using Tool or adapter case (4WD models)
using suitable tool.
CAUTION:
• Apply ATF to rear oil seal.
• Do not reuse rear oil seal.
2. Install transfer to transmission (4WD models). Refer to
151, "Removal and Installation"
(ATX14B),
(TX15B).
3. Install rear propeller shaft. Refer to
(2S1330) or
DLN-336, "Removal and Installation"
(2S1350).
4. Check the A/T fluid level and for fluid leakage. Refer to
.
SCIA5254E
Tool number
: ST33400001 (J-26082)
WCIA0475E
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст