Nissan Pathfinder (2010 year). Manual — part 632
TM-184
< ON-VEHICLE REPAIR >
KEY INTERLOCK CABLE
KEY INTERLOCK CABLE
Component
INFOID:0000000005258188
CAUTION:
• Install key interlock cable in such a way that it will not be damaged by sharp bends, twists or interfer-
ence with adjacent parts.
• After installing key interlock cable to control device, make sure that casing cap and bracket are
firmly secured in their positions. If casing cap can be removed with an external load of less than 39
N (4.0 kg, 8.8 lb), replace key interlock cable with new one.
Removal and Installation
INFOID:0000000005258189
REMOVAL
1. Remove lower glove box. Refer to
IP-12, "Removal and Installation"
2. Remove A/T finisher. Refer to
.
3. Remove lower instrument panel LH. Refer to
WCIA0467E
2010 Pathfinder
KEY INTERLOCK CABLE
TM-185
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4. Unlock slider from adjuster holder by squeezing lock tabs.
5. Remove casing cap from bracket of control device assembly
and remove interlock rod from adjuster holder.
6. Remove holder from key cylinder and remove key interlock
cable.
INSTALLATION
1. Set key interlock cable to key cylinder and install holder.
2. Turn ignition key to (LOCK) position.
3. Set selector lever to (P) position.
SCIA1230E
LCIA0375E
SCIA2258E
2010 Pathfinder
TM-186
< ON-VEHICLE REPAIR >
KEY INTERLOCK CABLE
4. Insert interlock rod into adjuster holder.
5. Install casing cap to bracket.
6. Move slider in order to secure adjuster holder to interlock rod.
7. Install lower instrument panel LH. Refer to
.
8. Install A/T finisher. Refer to
9. Install lower glove box. Refer to
SCIA1232E
2010 Pathfinder
AIR BREATHER HOSE
TM-187
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
AIR BREATHER HOSE
2WD
2WD : Removal and Installation
INFOID:0000000005258190
VQ40DE Models
CAUTION:
• Install air breather hose with paint mark at upper side.
• When installing the air breather hose, do not crush or block by folding or bending the hose.
• When inserting the hose to the transmission tube, be sure to insert it fully until its end reaches the
tube bend portion.
• Make sure clip is securely installed to bracket.
4WD
4WD : Removal and Installation
INFOID:0000000005258191
VQ40DE Models
1.
Air breather hose
2.
Transmission assembly
A.
Paint mark
B.
Clip
WCIA0663E
2010 Pathfinder
TM-188
< ON-VEHICLE REPAIR >
AIR BREATHER HOSE
CAUTION:
• Install air breather hose with paint mark at upper side.
• When installing an air breather hose, do not crush or block by folding or bending the hose.
• When inserting a hose to the transmission tube, be sure to insert it fully until its end reaches the
tube bend portion.
• Make sure clip is securely installed to bracket
VK56DE Models
1.
Air breather hose
2.
Transmission assembly
A.
Paint mark
B.
Clip
WCIA0664E
2010 Pathfinder
AIR BREATHER HOSE
TM-189
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CAUTION:
• Install air breather hose with paint mark at upper side.
• When installing an air breather hose, do not crush or block by folding or bending the hose.
• When inserting a hose to the transmission tube, be sure to insert it fully until its end reaches the
tube bend portion.
• Make sure clip is securely installed to bracket
A.
Air breather hose
B.
Clip (set securely to bracket)
AWDIA0555GB
2010 Pathfinder
TM-190
< ON-VEHICLE REPAIR >
A/T FLUID COOLER
A/T FLUID COOLER
Removal and Installation
INFOID:0000000005258192
REMOVAL
1. Remove front grill. Refer to
EXT-18, "Removal and Installation"
2. Remove A/T fluid cooler hoses from fluid cooler.
3. Remove A/T fluid cooler.
INSTALLATION
Installation is in the reverse order of removal.
• After completing installation, check fluid level and check for fluid leakage. Refer to
1.
A/T fluid cooler
2.
Fluid cooler tube
3.
Clip
4.
Hose clamp
5.
Cooler hose (lower)
6.
Cooler hose
7.
Tube joint
8.
Cooler hose (upper)
A.
To transmission
B.
From radiator
AWDIA0624GB
2010 Pathfinder
TRANSMISSION ASSEMBLY
TM-191
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL AND INSTALLATION
TRANSMISSION ASSEMBLY
2WD
2WD : Exploded View
INFOID:0000000005258193
2WD : Removal and Installation
INFOID:0000000005258194
REMOVAL
CAUTION:
When removing the A/T assembly from engine, first remove the crankshaft position sensor (POS) from
the A/T assembly.
1. Disconnect the negative battery terminal.
2. Remove the A/T fluid level gauge.
3. Remove front LH wheel and tire assembly. Refer to
4. Remove the front LH mud flap. Refer to
EXT-24, "Removal and Installation"
.
5. Remove the LH fender protector. Refer to
EXT-23, "Removal and Installation of Front Fender Protector"
AWDIA0622GB
1.
A/T fluid level gauge
2.
A/T fluid charging pipe
3.
O-ring
4.
Insulator
5.
A/T crossmember
6.
Copper washer
7.
Bracket
8.
A/T fluid cooler tube
9.
Front crossmember
10. Transmission assembly
A. Self-sealing bolt
B. Refer to installation.
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст