Murano Cross Cabriolet Z51 (2012 year). Manual — part 34
EXL-68
< PERIODIC MAINTENANCE >
[XENON TYPE]
FRONT FOG LAMP AIMING ADJUSTMENT
FRONT FOG LAMP AIMING ADJUSTMENT
Description
INFOID:0000000007565467
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
• Turn the aiming adjusting screw for adjustment.
• For the position and direction of the adjusting screw, refer to the
figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.
Aiming Adjustment Procedure
INFOID:0000000007565468
1.
Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
2.
Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.
3.
Start the engine. Illuminate the front fog lamp.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
4.
Adjust the cutoff line height (A) with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and (A) becomes 200 mm (7.87 in).
Front fog lamp light distribution on the screen
A: UP
B: DOWN
JPLIA0811ZZ
JPLIA0008ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
FRONT FOG LAMP AIMING ADJUSTMENT
EXL-69
< PERIODIC MAINTENANCE >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
A
: Cutoff line
B
: High illuminance area
H
: Horizontal center line of front fog lamp
V
: Vertical center line of front fog lamp
X
: Cutoff line height
Revision: 2013 February
2012 Murano CrossCabriolet
EXL-70
< REMOVAL AND INSTALLATION >
[XENON TYPE]
FRONT COMBINATION LAMP
REMOVAL AND INSTALLATION
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000007565469
REMOVAL
DISASSEMBLY
1.
Front combination lamp
2.
Headlamp extension panel
JPLIA0812ZZ
1.
Front side marker lamp bulb
2.
Front side marker lamp bulb socket
3.
Resin cap
4.
Seal packing
5.
Xenon bulb socket (Starter)
6.
Xenon bulb
7.
Retaining spring
8.
Seal packing
9.
HID control unit (Inverter)
10.
Parking lamp bulb socket
11. Parking lamp bulb
12. Front turn signal lamp bulb socket
13.
Front turn signal lamp bulb
14. Headlamp housing assembly
JPLIA0813ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
FRONT COMBINATION LAMP
EXL-71
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Removal and Installation
INFOID:0000000007565470
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
1.
Remove the front grille. Refer to
2.
Remove the headlamp extension panel.
3.
Remove the front bumper fascia. Refer to
.
4.
Remove the headlamp mounting bolts.
5.
Remove the harness clips from headlamp housing assembly.
6.
Pull out the headlamp assembly forward the vehicle.
7.
Disconnect the connector before removing the headlamp assembly.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000007565471
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB
1.
Remove the fender rubber protector in engine room.
2.
Rotate the resin cap counterclockwise and unlock it.
3.
Rotate the bulb socket counterclockwise and unlock it.
4.
Unlock the retaining spring. And then remove the bulb from the
headlamp housing assembly.
CAUTION:
Never break the xenon bulb ceramic tube when replacing
the bulb.
PARKING LAMP BULB
1.
Rotate the bulb socket counterclockwise and unlock it.
2.
Remove the bulb from the bulb socket.
FRONT TURN SIGNAL LAMP BULB
1.
Remove the front grille.
2.
Rotate the bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the bulb socket.
FRONT SIDE MARKER LAMP BULB
1.
Remove the fender rubber protector in engine room.
2.
Rotate the bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the bulb socket.
JPLIA0814ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
EXL-72
< REMOVAL AND INSTALLATION >
[XENON TYPE]
FRONT COMBINATION LAMP
Disassembly and Assembly
INFOID:0000000007565472
DISASSEMBLY
1.
Rotate the resin cap counterclockwise and unlock it.
2.
Rotate the xenon bulb socket counterclockwise and unlock it.
3.
Unlock the retaining spring. And then remove the xenon bulb.
4.
Remove the HID control unit installation screw.
5.
Remove the screw. And then disconnect the connector from HID control unit.
6.
Remove the xenon bulb socket from headlamp housing assembly.
7.
Rotate the parking lamp bulb socket counterclockwise and unlock it.
8.
Remove the bulb from parking lamp bulb socket.
9.
Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
10. Remove the bulb from front turn signal lamp bulb socket.
11. Rotate the front side marker lamp bulb socket counterclockwise and unlock it.
12. Remove the bulb from front side marker lamp bulb socket.
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION:
• Install HID control unit securely.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
Revision: 2013 February
2012 Murano CrossCabriolet
FRONT FOG LAMP
EXL-73
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP
Exploded View
INFOID:0000000007565473
Removal and Installation
INFOID:0000000007565474
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the front fender protector. Keep a service area. Refer to
.
2.
Remove the front fog lamp connector.
3.
Remove the screw.
4.
Disengage the pawl. And then remove the front fog lamp.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000007565475
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT FOG LAMP BULB
1.
Remove the front fender protector. Keep the service area. Refer to
.
1.
Front fog lamp
: Pawl
JPLIA1592ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
EXL-74
< REMOVAL AND INSTALLATION >
[XENON TYPE]
FRONT FOG LAMP
2.
Remove the front fog lamp bulb connector (1).
3.
Rotate the bulb (2) counterclockwise and unlock it.
JPLIA0816ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
OPTICAL SENSOR
EXL-75
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
OPTICAL SENSOR
Exploded View
INFOID:0000000007565476
Removal and Installation
INFOID:0000000007565477
REMOVAL
1.
Insert an appropriate tool between the optical sensor and the instrument upper panel. Pull out the optical
sensor upward.
2.
Disconnect the optical sensor connector. And then remove the optical sensor.
INSTALLATION
Install in the reverse order of removal.
1.
Optical sensor
JPLIA0818ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
EXL-76
< REMOVAL AND INSTALLATION >
[XENON TYPE]
LIGHTING & TURN SIGNAL SWITCH
LIGHTING & TURN SIGNAL SWITCH
Exploded View
INFOID:0000000007565478
Removal and Installation
INFOID:0000000007565479
Lighting & turn signal switch is integrated in the combination switch. Refer to
Revision: 2013 February
2012 Murano CrossCabriolet
HAZARD SWITCH
EXL-77
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HAZARD SWITCH
Exploded View
INFOID:0000000007565480
Removal and Installation
INFOID:0000000007565481
REMOVAL
1.
Remove the instrument stay cover (RH). Refer to
.
2.
Remove the screws. And then remove the switch bracket from the instrument stay cover.
3.
Remove the hazard switch.
INSTALLATION
Install in the reverse order of removal.
1.
Hazard switch
2.
Switch bracket
A.
Pawls
JPLIA0819ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
EXL-78
< REMOVAL AND INSTALLATION >
[XENON TYPE]
HEADLAMP AIMING SWITCH
HEADLAMP AIMING SWITCH
Exploded View
INFOID:0000000007565482
Removal and Installation
INFOID:0000000007565483
REMOVAL
1.
Remove the instrument driver lower panel. Refer to
.
2.
Disengage the pawls. And remove the headlamp aiming switch.
INSTALLATION
Install in the reverse order of removal.
1.
Headlamp aiming switch
A.
Pawls
JPLIA0820ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
REAR COMBINATION LAMP
EXL-79
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REAR COMBINATION LAMP
Exploded View
INFOID:0000000007565484
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000007565485
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Grommet
2.
Rear combination lamp
3.
Rear combination lamp finisher
: Pawl
Refer to
JMLIA2257GB
1.
Rear combination lamp housing
2.
Rear combination lamp harness
3.
Rear side marker lamp bulb
4.
Rear turn signal lamp bulb
JMLIA2280ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
EXL-80
< REMOVAL AND INSTALLATION >
[XENON TYPE]
REAR COMBINATION LAMP
1.
Disengage rear combination lamp finisher fixing pawls as shown
by the arrow in the figure, and then remove the rear combination
lamp finisher.
2.
Remove the rear combination lamp mounting bolts.
3.
Pull the rear combination lamp toward outside of the vehicle, and then remove the rear combination lamp.
4.
Disconnect the rear combination lamp connector.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000007565486
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP/TAIL LAMP
Replacement integral with rear combination lamp. Refer to
EXL-79, "Removal and Installation"
.
REAR SIDE MARKER LAMP BULB
1.
Remove the rear combination lamp. Refer to
EXL-79, "Removal and Installation"
.
2.
Rotate the rear side marker lamp bulb socket counterclockwise, and unlock it.
3.
Remove the bulb from the rear side marker lamp bulb socket.
REAR TURN SIGNAL LAMP BULB
1.
Remove the rear combination lamp. Refer to
EXL-79, "Removal and Installation"
.
2.
Rotate the rear turn signal lamp bulb socket counterclockwise, and unlock it.
3.
Remove the bulb from the rear turn signal lamp bulb socket.
JMKIA8577ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
HIGH-MOUNTED STOP LAMP
EXL-81
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HIGH-MOUNTED STOP LAMP
Exploded View
INFOID:0000000007565487
Removal and Installation
INFOID:0000000007565488
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1.
Remove trunk lid trim. Refer to
INT-37, "Removal and Installation"
2.
Disconnect high-mounted stop lamp (1) harness connector (A).
3.
Remove high-mounted stop lamp mounting nuts (B).
4.
Remove high-mounted stop lamp bracket.
5.
Disengage high-mounted stop lamp fixing pawls, and then
remove high-mounted stop lamp.
1.
High-mounted stop lamp bracket
2.
Trunk lid
3.
High-mounted stop lamp
: Pawl
Refer to
JMLIA2259GB
JMLIA2281ZZ
: Pawl
JMLIA2282ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
EXL-82
< REMOVAL AND INSTALLATION >
[XENON TYPE]
HIGH-MOUNTED STOP LAMP
INSTALLATION
Install in the reverse order of removal.
Revision: 2013 February
2012 Murano CrossCabriolet
BACK-UP LAMP
EXL-83
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BACK-UP LAMP
Exploded View
INFOID:0000000007565489
Removal and Installation
INFOID:0000000007565490
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the trunk lid trim. Refer to
INT-37, "Removal and Installation"
.
2.
Remove the back-up lamp mounting nuts.
3.
Disconnect the back-up lamp connector, and then remove the back-up lamp.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Seal packing cannot be reused.
Replacement
INFOID:0000000007565491
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
BACK-UP LAMP BULB
1.
Remove the trunk lid trim. Refer to
INT-37, "Removal and Installation"
.
2.
Rotate the back-up lamp bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the back-up lamp bulb socket.
1.
Trunk lid
2.
Seal packing
3.
Back-up lamp housing
4.
Back-up lamp bulb
5.
Back-up lamp bulb socket
Refer to
JMLIA2258GB
Revision: 2013 February
2012 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст