Murano Cross Cabriolet Z51 (2012 year). Manual — part 81
B261A PUSH-BUTTON IGNITION SWITCH
SEC-79
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 3.
3.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT 1
1.
Disconnect BCM connector.
2.
Check continuity between push-button ignition switch harness connector and BCM harness connector.
3.
Check continuity between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness or connector.
4.
CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL 2
1.
Turn ignition switch OFF.
2.
Disconnect push-button ignition switch connector and BCM connector.
3.
Check voltage between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 5.
5.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT 2
1.
Disconnect IPDM E/R connector.
2.
Check continuity between push-button ignition switch harness connector and IPDM E/R harness connec-
tor.
3.
Check continuity between push-button ignition switch harness connector and ground.
Is the inspection result normal?
(+)
(–)
Voltage (V)
(Approx.)
Push-button ignition switch
Connector
Terminal
M101
4
Ground
Battery voltage
Push-button ignition switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
M101
4
M121
60
Existed
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M101
4
Not existed
(+)
(–)
Voltage (V)
(Approx.)
Push-button ignition switch
Connector
Terminal
M101
4
Ground
Battery voltage
Push-button ignition switch
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
M101
4
E10
28
Existed
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M101
4
Not existed
Revision: 2013 February
2012 Murano CrossCabriolet
SEC-80
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B261A PUSH-BUTTON IGNITION SWITCH
YES
>> GO TO 6.
NO
>> Repair or replace harness or connector.
6.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
>> INSPECTION END
Revision: 2013 February
2012 Murano CrossCabriolet
B261E VEHICLE TYPE
SEC-81
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B261E VEHICLE TYPE
Description
INFOID:0000000007563299
There are two types of vehicle.
• HEV
• Conventional
DTC Logic
INFOID:0000000007563300
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007563301
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Select “Self Diagnostic Result” mode of “BCM” using CONSULT.
3.
Touch “ERASE”.
4.
Perform DTC CONFIRMATION PROCEDURE for DTC B261E. Refer to
.
Is the DTC displayed?
YES
>> Replace BCM. Refer to
BCS-76, "Removal and Installation"
NO
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B261E
VEHICLE TYPE
Difference of BCM configuration
BCM
Revision: 2013 February
2012 Murano CrossCabriolet
SEC-82
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B26EA KEY REGISTRATION
B26EA KEY REGISTRATION
DTC Logic
INFOID:0000000007563302
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
2.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007563303
1.
PERFORM INITIALIZATION
1.
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
2.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE INTELLIGENT KEY
1.
Replace Intelligent Key.
2.
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
3.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Replace BCM. Refer to
BCS-76, "Removal and Installation"
NO
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B26EA
KEY REGISTRATION
Intelligent Key is not registered successfully.
• Improper registration operation
• Intelligent Key
• BCM
Revision: 2013 February
2012 Murano CrossCabriolet
B210B STARTER CONTROL RELAY
SEC-83
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210B STARTER CONTROL RELAY
DTC Logic
INFOID:0000000007563304
DTC DETECTION LOGIC
NOTE:
If DTC B210B is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Press push-button ignition switch under the following conditions to start engine, and wait 1 second or
more.
-
Selector lever: In the P or N position.
-
Brake pedal: Depressed
2.
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007563305
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
3.
Touch “ERASE”.
4.
Perform DTC CONFIRMATION PROCEDURE for DTC B210B. Refer to
.
Is the DTC B210B displayed again?
YES
>> Replace IPDM E/R. Refer
PCS-31, "Removal and Installation"
NO
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210B
START CONT RLY ON
IPDM E/R detects that the relay is stuck at ON position
even if the following conditions are met for about 1
second.
• Starter control relay ON/OFF signal from BCM
• P/N position signal from TCM
• Harness or connectors
(The CAN communication line
is open or shorted.)
• IPDM E/R
Revision: 2013 February
2012 Murano CrossCabriolet
SEC-84
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210C STARTER CONTROL RELAY
B210C STARTER CONTROL RELAY
DTC Logic
INFOID:0000000007563306
DTC DETECTION LOGIC
NOTE:
• If DTC B210C is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210C may be
detected.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Press push-button ignition switch under the following conditions to start engine, and wait 1 second or
more.
-
Selector lever: In the P or N position.
-
Brake pedal: Depressed
2.
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007563307
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
3.
Touch “ERASE”.
4.
Perform DTC CONFIRMATION PROCEDURE for DTC B210C. Refer to
.
Is the DTC B210C displayed again?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
NO
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210C
START CONT RLY OFF
IPDM E/R detects that the relay is stuck at OFF
position even if the followings condition are met
for about 1 second.
• Starter control relay ON/OFF signal from BCM
• P/N position signal from TCM
• Harness or connectors
(The CAN communication line is
open or shorted.)
• IPDM E/R
• Battery
Revision: 2013 February
2012 Murano CrossCabriolet
B210D STARTER RELAY
SEC-85
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210D STARTER RELAY
DTC Logic
INFOID:0000000007563308
DTC DETECTION LOGIC
NOTE:
• If DTC B210D is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B210D is displayed with DTC B2617, first perform the trouble diagnosis for DTC B2617. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Ignition switch ON and wait 1 second or more.
2.
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007563309
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
3.
Touch “ERASE”.
4.
Perform DTC CONFIRMATION PROCEDURE for DTC B210D. Refer to
.
Is the DTC B210D displayed again?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
NO
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210D
STARTER RELAY ON
IPDM E/R detects that the relay is stuck at ON
position even if the followings condition are met
for about 1 second.
• Starter control relay ON/OFF signal from BCM
• P/N position signal from TCM
• Harness or connectors
(The CAN communication
line is open or shorted.)
• IPDM E/R
Revision: 2013 February
2012 Murano CrossCabriolet
SEC-86
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210E STARTER RELAY
B210E STARTER RELAY
DTC Logic
INFOID:0000000007563310
DTC DETECTION LOGIC
NOTE:
• If DTC B210E is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B210E is displayed with DTC B2110 for IPDM E/R, first perform the trouble diagnosis for DTC B2110.
.
• If DTC B210E is displayed with DTC B2617 for BCM, first perform the trouble diagnosis for DTC B2617.
.
• When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210F may be
detected.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait 1 second or more.
2.
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007563311
1.
CHECK STARTER RELAY OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK STARTER RELAY OUTPUT SIGNAL CIRCUIT
1.
Disconnect IPDM E/R connector.
2.
Check continuity between BCM harness connector and IPDM E/R harness connector.
3.
Check continuity between BCM harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210E
STARTER RELAY OFF
IPDM E/R detects that the relay is stuck at OFF
position even if the followings condition are met
for about 1 second.
• Starter control relay ON/OFF signal from BCM
• P/N position signal from TCM
• Harness or connectors
(The CAN communication line is
open or shorted.)
• IPDM E/R
• Battery
(+)
(–)
Condition
Voltage (V)
(Approx.)
BCM connector
Connector
Terminal
Ignition switch
Brake pedal
Selector lever
M121
52
Ground
ON
Depressed
P or N
Battery voltage
Other than
above
0
BCM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
M121
52
E11
46
Existed
Revision: 2013 February
2012 Murano CrossCabriolet
B210E STARTER RELAY
SEC-87
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
NO
>> Repair or replace harness or connector.
3.
CHECK STARTER RELAY POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
NO
>> Check harness for open or short between IPDM E/R and battery. Refer to
BCM
Ground
Continuity
Connector
Terminal
M121
52
Not existed
(+)
(–)
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E10
36
Ground
Battery voltage
Revision: 2013 February
2012 Murano CrossCabriolet
SEC-88
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
DTC Logic
INFOID:0000000007563312
DTC DETECTION LOGIC
NOTE:
If DTC B210F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait 1 second or more.
2.
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007563313
1.
CHECK DTC OF BCM
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK P/N POSITION SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
NO
>> GO TO 3.
3.
CHECK P/N POSITION SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector and IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and TCM harness connector.
4.
Check continuity between IPDM E/R harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210F
INTRLCK/PNP SW ON
IPDM E/R detects a mismatch between the sig-
nals below for 1 second or more.
• P/N position signal from TCM
• Shift position signal from BCM (CAN)
• Harness or connectors
(The CAN communication line is
open or shorted.)
• Harness or connectors
(TCM circuit is open or shorted.)
• TCM
(+)
(–)
Condition
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E10
30
Ground
Selector lever
P or N
Battery voltage
Other than above
0
IPDM E/R
TCM
Continuity
Connector
Terminal
Connector
Terminal
F12
72
F23
20
Existed
Revision: 2013 February
2012 Murano CrossCabriolet
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
SEC-89
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
NO
>> Repair or replace harness or connector.
IPDM E/R
Ground
Continuity
Connector
Terminal
F12
72
Not existed
Revision: 2013 February
2012 Murano CrossCabriolet
SEC-90
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
DTC Logic
INFOID:0000000007563314
DTC DETECTION LOGIC
NOTE:
If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn the ignition switch ON and wait 1 second or more.
2.
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007563315
1.
CHECK DTC OF TCM
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK P/N POSITION SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
NO
>> GO TO 3.
3.
CHECK P/N POSITION SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector and IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and TCM harness connector.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2110
INTRLCK/PNP SW OFF
IPDM E/R detects mismatch between the following
signals for 1 second or more.
• P/N position signal from TCM
• Shift position signal from BCM (CAN)
• Harness or connectors
(The CAN communication line is open
or shorted.)
• Harness or connectors
(TCM circuit is open or shorted.)
• TCM
• IPDM E/R
• BCM
(+)
(–)
Condition
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E10
30
Ground
Selector lever
P or N
Battery voltage
Other than above
0
Revision: 2013 February
2012 Murano CrossCabriolet
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
SEC-91
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
NO
>> Repair or replace harness or connector.
IPDM E/R
TCM
Continuity
Connector
Terminal
Connector
Terminal
F12
72
F23
20
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
F12
72
Not existed
Revision: 2013 February
2012 Murano CrossCabriolet
SEC-92
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
HEADLAMP FUNCTION
HEADLAMP FUNCTION
Component Function Check
INFOID:0000000007563316
1.
CHECK FUNCTION
1.
Perform “HEAD LAMP(HI)” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CONSULT.
2.
Check headlamps operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007563317
1.
CHECK HEADLAMP FUNCTION
EXL-37, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
>> INSPECTION END
Test item
Description
HEAD LAMP (HI)
ON
Headlamps (Hi)
Light
OFF
Do not light
Revision: 2013 February
2012 Murano CrossCabriolet
HORN FUNCTION
SEC-93
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
HORN FUNCTION
Component Function Check
INFOID:0000000007563318
1.
CHECK FUNCTION
1.
Perform “VEHICLE SECURITY HORN” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CON-
SULT.
2.
Check the horn operation.
Is the operation normal?
YES
>> INSPECTION END
NO
>> Go to
.
Diagnosis Procedure
INFOID:0000000007563319
1.
CHECK HORN FUNCTION
Check that horns function properly using horn switch.
Does horn sound?
YES
>> GO TO 2.
NO
>> Check horn circuit. Refer to
2.
CHECK HORN CONTROL CIRCUIT
1.
Disconnect horn relay.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and horn relay harness connector.
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
NO
>> Repair or replace harness.
Test item
Description
VEHICLE SECURITY HORN
ON
Horn
Sounds (for 0.5 sec)
IPDM E/R
Horn relay
Continuity
Connector
Terminal
Connector
Terminal
E11
44
E5
1
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E11
44
Not existed
Revision: 2013 February
2012 Murano CrossCabriolet
SEC-94
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
KEY WARNING LAMP
KEY WARNING LAMP
Component Function Check
INFOID:0000000007563320
1.
CHECK FUNCTION
Check the operation with “INDICATOR” in “Active Test” mode with CONSULT.
Is the inspection result normal?
YES
>> Key warning lamp in combination meter is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007563321
1.
CHECK KEY WARNING LAMP
SEC-94, "Component Function Check"
Is the inspection result normal?
Yes
>> GO TO 2.
No
>> Repair or replace key warning lamp circuit.
2.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
>> INSPECTION END
Test item
Condition
INDICATOR
KEY ON
Key warning lamp illuminates
KEY IND
Key warning lamp flashes
Revision: 2013 February
2012 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст