Murano Cross Cabriolet Z51 (2012 year). Manual — part 82
SECURITY INDICATOR LAMP
SEC-95
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
SECURITY INDICATOR LAMP
Component Function Check
INFOID:0000000007563322
1.
CHECK FUNCTION
1.
Perform “THEFT IND” in the “ACTIVE TEST” mode with CONSULT.
2.
Check security indicator lamp operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000007563323
1.
CHECK SECURITY INDICATOR LAMP POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect security indicator lamp connector.
3.
Check voltage between security indicator lamp harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO-1
>> Check 10A fuse [No. 9, located in the fuse block (J/B)].
NO-2
>> Check harness for open or short between security indicator lamp and fuse.
2.
CHECK SECURITY INDICATOR LAMP SIGNAL
1.
Connect security indicator lamp connector.
2.
Disconnect BCM connector.
3.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-76, "Removal and Installation"
NO
>> GO TO 3.
3.
CHECK SECURITY INDICATOR LAMP SIGNAL CIRCUIT
1.
Disconnect security indicator lamp connector.
2.
Check continuity between security indicator lamp harness connector and BCM harness connector.
3.
Check continuity between security indicator lamp harness connector and ground.
Test item
Description
THEFT IND
ON
Security indicator lamp
Illuminate
OFF
Not illuminate
(+)
(–)
Voltage (V)
(Approx.)
Security indicator lamp
Connector
Terminal
M100
1
Ground
Battery voltage
(+)
(–)
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M123
141
Ground
Battery voltage
Security indicator lamp
BCM
Continuity
Connector
Terminal
Connector
Terminal
M100
2
M123
141
Existed
Revision: 2013 February
2012 Murano CrossCabriolet
SEC-96
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
SECURITY INDICATOR LAMP
Is the inspection result normal?
YES
>> Replace security indicator lamp. Refer to
SEC-110, "Removal and Installation"
NO
>> Repair or replace harness.
Security indicator lamp
Ground
Continuity
Connector
Terminal
M100
2
Not existed
Revision: 2013 February
2012 Murano CrossCabriolet
TRUNK KEY CYLINDER SWITCH
SEC-97
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
TRUNK KEY CYLINDER SWITCH
Component Function Check
INFOID:0000000007563324
1.
CHECK FUNCTION
1.
Select “KEY CYL SW-TR” in “Data Monitor” mode of “THEFT ALM” of “BCM” using CONSULT.
2.
Check the indication under the following conditions.
Is the inspection result normal?
YES
>> Trunk key cylinder switch is OK.
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000007563325
1.
CHECK TRUNK KEY CYLINDER SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect trunk key cylinder switch connector.
3.
Check voltage between trunk key cylinder switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK TRUNK KEY CYLINDER SWITCH SIGNAL CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and trunk key cylinder switch harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-76, "Removal and Installation"
.
2.
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
>> INSPECTION END
Monitor item
Condition
Indication
KEY CYL SW-TR
Trunk key cylinder switch
Off position
Off
On (Trunk lid open) position
On
(+)
(–)
Voltage
(Approx.)
Trunk key cylinder switch
Connector
Terminal
T11
1
Ground
12 V
BCM
Trunk key cylinder switch
Continuity
Connector
Terminal
Connector
Terminal
M121
49
T11
1
Existed
BCM
Ground
Continuity
Connector
Terminal
M121
49
Not existed
Revision: 2013 February
2012 Murano CrossCabriolet
SEC-98
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
TRUNK KEY CYLINDER SWITCH
4.
CHECK TRUNK KEY CYLINDER SWITCH GROUND CIRCUIT
Check continuity between trunk key cylinder switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK TRUNK KEY CYLINDER SWITCH
SEC-98, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace trunk key cylinder switch.
6.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000007563326
1.
CHECK TRUNK KEY CYLINDER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect trunk key cylinder switch connector.
3.
Check continuity between trunk key cylinder switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace trunk key cylinder switch.
Trunk key cylinder switch
Ground
Continuity
Connector
Terminal
T11
2
Existed
Trunk key cylinder switch
Condition
Continuity
Terminal
1
2
Trunk lid key cylinder
Off position
Not existed
On (trunk lid open) position
Existed
Revision: 2013 February
2012 Murano CrossCabriolet
ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VEHICLE
SEC-99
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
SYMPTOM DIAGNOSIS
ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VE-
HICLE
Description
INFOID:0000000007563327
Engine does not start when push-button ignition switch is pressed while carrying Intelligent Key.
NOTE:
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
• The engine start function, door lock function, power distribution system, and NATS-IVIS/NVIS in the Intelli-
gent Key system are closely related to each other regarding control. The vehicle security function can oper-
ate only when the door lock and power distribution system are operating normally.
Conditions of Vehicle (Operating Conditions)
• “ENGINE START BY I-KEY” setting: ON
Check the setting of “ENGINE START BY I-KEY” in “Work Support” mode of “INTELLIGENT KEY” of “BCM”
using CONSULT.
• Intelligent Key is not inserted into key slot.
• One or more of Intelligent Keys with registered Intelligent Key ID is in the vehicle.
Diagnosis Procedure
INFOID:0000000007563328
1.
PERFORM WORK SUPPORT
Perform “INSIDE ANT DIAGNOSIS” in “Work Support” mode of “INTELLIGENT KEY” of “BCM” using CON-
SULT.
Refer to
SEC-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
.
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSTIC RESULT
Select “Self Diagnostic Result” mode of “BCM”, and check whether or not DTC of inside key antenna is
detected.
Is DTC detected?
YES
>> Refer to
(trunk room).
NO
>> GO TO 3.
3.
CHECK PUSH-BUTTON IGNITION SWITCH
Check push-button ignition switch.
Refer to
PCS-65, "Component Function Check"
Is the operation normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2013 February
2012 Murano CrossCabriolet
SEC-100
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK
SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK
Description
INFOID:0000000007563329
Security indicator lamp does not blink when ignition switch is in a position other than ON.
NOTE:
• Before performing the diagnosis in the following table, check “Work Flow”. Refer to
.
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
Conditions of Vehicle (Operating Conditions)
• Intelligent Key is not inserted in key slot.
• Ignition switch position is not in the ON position.
Diagnosis Procedure
INFOID:0000000007563330
1.
CHECK SECURITY INDICATOR LAMP
Check security indicator lamp.
Refer to
SEC-95, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2013 February
2012 Murano CrossCabriolet
VEHICLE SECURITY SYSTEM CANNOT BE SET
SEC-101
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
VEHICLE SECURITY SYSTEM CANNOT BE SET
INTELLIGENT KEY
INTELLIGENT KEY : Description
INFOID:0000000007563331
ARMED phase is not activated when all doors are locked using Intelligent Key.
NOTE:
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check
each symptom.
CONDITION OF VEHICLE (OPERATING CONDITION)
• “ENGINE START BY I-KEY” setting: ON
Check the setting of “ENGINE START BY I-KEY” in “Work Support” mode of “INTELLIGENT KEY” of “BCM”
using CONSULT.
INTELLIGENT KEY : Diagnosis Procedure
INFOID:0000000007563332
1.
CHECK INTELLIGENT KEY SYSTEM (REMOTE KEYLESS ENTRY FUNCTION)
Lock/unlock door with Intelligent Key.
Refer to
DLK-20, "REMOTE KEYLESS ENTRY FUNCTION : System Description"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check Intelligent Key system (remote keyless entry function). Refer to
2.
CHECK DOOR SWITCH
Check door switch circuit.
Refer to
DLK-55, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts. Refer to
3.
CHECK TRUNK ROOM LAMP SWITCH
Check trunk room lamp switch circuit.
Refer to
DLK-69, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts. Refer to
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
DOOR REQUEST SWITCH
DOOR REQUEST SWITCH : Description
INFOID:0000000007563333
ARMED phase is not activated when all doors are locked using door request switch.
NOTE:
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check
each symptom.
CONDITION OF VEHICLE (OPERATING CONDITION)
• “ENGINE START BY I-KEY” setting: ON
Check the setting of “ENGINE START BY I-KEY” in “Work Support” mode of “INTELLIGENT KEY” of “BCM”
using CONSULT.
Revision: 2013 February
2012 Murano CrossCabriolet
SEC-102
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY SYSTEM CANNOT BE SET
DOOR REQUEST SWITCH : Diagnosis Procedure
INFOID:0000000007563334
1.
CHECK INTELLIGENT KEY SYSTEM (DOOR LOCK FUNCTION)
Lock/unlock door with door request switch.
Refer to
DLK-16, "DOOR LOCK FUNCTION : System Description"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check Intelligent Key system (door lock function). Refer to
DLK-102, "ALL DOOR : Diagnosis Pro-
2.
CHECK DOOR SWITCH
Check door switch circuit.
Refer to
DLK-55, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK TRUNK ROOM LAMP SWITCH
Check trunk room lamp switch circuit.
Refer to
DLK-69, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
DOOR KEY CYLINDER
DOOR KEY CYLINDER : Description
INFOID:0000000007563335
ARMED phase is not activated when all doors are locked using mechanical key.
DOOR KEY CYLINDER : Diagnosis Procedure
INFOID:0000000007563336
1.
CHECK POWER DOOR LOCK SYSTEM
Lock/unlock door with mechanical key.
Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check power door lock system. Refer to
DLK-101, "Diagnosis Procedure"
2.
CHECK DOOR SWITCH
Check door switch circuit.
Refer to
DLK-55, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK TRUNK ROOM LAMP SWITCH
Check trunk room lamp switch circuit.
Refer to
DLK-69, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
Revision: 2013 February
2012 Murano CrossCabriolet
VEHICLE SECURITY SYSTEM CANNOT BE SET
SEC-103
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
NO
>> Repair or replace malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
DOOR LOCK AND UNLOCK SWITCH
DOOR LOCK AND UNLOCK SWITCH : Description
INFOID:0000000007563337
Armed phase is not activated when all doors are locked by door lock and unlock switch.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
DOOR LOCK AND UNLOCK SWITCH : Diagnosis Procedure
INFOID:0000000007563338
1.
CHECK DTC OF SOFT TOP CONTROL UNIT
Check DTC in “Self Diagnostic Result” mode of “CONVERTIBLE ROOF” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis regarding to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK DOOR LOCK FUNCTION
Lock/unlock door using door lock and unlock switches (Driver side and passenger side).
Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check power door lock system. Refer to
DLK-99, "ALL DOOR : Diagnosis Procedure"
.
3.
CHECK DOOR SWITCH
Check door switch circuit.
Refer to
DLK-55, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CHECK TRUNK ROOM LAMP SWITCH
Check trunk room lamp switch circuit.
Refer to
DLK-69, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning parts.
5.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2013 February
2012 Murano CrossCabriolet
SEC-104
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY ALARM DOES NOT ACTIVATE
VEHICLE SECURITY ALARM DOES NOT ACTIVATE
Description
INFOID:0000000007563339
Alarm does not operate when alarm operating condition is satisfied.
NOTE:
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check
each symptom.
CONDITION OF VEHICLE (OPERATING CONDITION)
• “ENGINE START BY I-KEY” setting: ON
Check the setting of “ENGINE START BY I-KEY” in “Work Support” mode of “INTELLIGENT KEY” of “BCM”
using CONSULT.
Diagnosis Procedure
INFOID:0000000007563340
1.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-55, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the malfunctioning door switch. Refer to
.
2.
CHECK TRUNK ROOM LAMP SWITCH
Check trunk room lamp switch circuit.
Refer to
DLK-69, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK HEADLAMP FUNCTION
Check headlamp function.
Refer to
SEC-92, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK HORN FUNCTION
Check horn function. Refer to
SEC-93, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2013 February
2012 Murano CrossCabriolet
INTELLIGENT KEY INSERT INFORMATION DOES NOT OPERATE
SEC-105
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
INTELLIGENT KEY INSERT INFORMATION DOES NOT OPERATE
Description
INFOID:0000000007563341
Intelligent Key insert information does not operate when push-button ignition switch is operated while Intelli-
gent Key is not inside vehicle.
NOTE:
Operating conditions of warning function are extremely complicated. Refer to
Diagnosis Procedure
INFOID:0000000007563342
1.
CHECK POWER POSITION
Check if ignition switch position is changing or not.
Does ignition switch position change?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK PUSH-BUTTON IGNITION SWITCH
Check push-button ignition switch.
Refer to
PCS-65, "Component Function Check"
Is the inspection result normal?
YES
>> Check BCM for DTC. Refer to
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-55, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK KEY SLOT
Check key slot.
Refer to
DLK-91, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
CHECK INFORMATION DISPLAY
Check information display.
Refer to
DLK-88, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
CHECK KEY SLOT INDICATOR
Check key slot indicator.
Refer to
DLK-93, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace the malfunctioning parts.
7.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2013 February
2012 Murano CrossCabriolet
SEC-106
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY INSERT INFORMATION DOES NOT OPERATE
NO
>> GO TO 1.
Revision: 2013 February
2012 Murano CrossCabriolet
PANIC ALARM FUNCTION DOES NOT OPERATE
SEC-107
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
PANIC ALARM FUNCTION DOES NOT OPERATE
Description
INFOID:0000000007563343
NOTE:
• Before performing the following procedure, check “Work Flow”. Refer to
.
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
CONDITIONS OF VEHICLE (OPERATION CONDITIONS)
• Power supply position: OFF or LOCK
• PANIC ALARM SET: MODE 1
Check the setting of “PANIC ALARM SET” in “Work Support” mode of “INTELLIGENT KEY” of “BCM” using
CONSULT.
Diagnosis Procedure
INFOID:0000000007563344
1.
CHECK REMOTE KEYLESS ENTRY FUNCTION
Check remote keyless entry function. Refer to
DLK-20, "REMOTE KEYLESS ENTRY FUNCTION : System
.
Does door lock or unlock when operating Intelligent key button?
YES
>> GO TO 2.
NO
>> Go to
DLK-104, "Diagnosis Procedure"
2.
CHECK VEHICLE SECURITY ALARM OPERATION
Check vehicle security alarm operation. Refer to
SEC-16, "VEHICLE SECURITY SYSTEM : System Descrip-
.
Is alarm (headlamps and horns) activated?
YES
>> GO TO 3.
NO
>> Go to
SEC-104, "Diagnosis Procedure"
.
3.
CHECK “PANIC ALARM” BUTTON OPERATION
1.
Turn ignition switch ON.
2.
Select “RKE-PANIC” and “RKE OPE COUN1” in “Data Monitor” mode of “INTELLIGENT KEY” of “BCM”
using CONSULT.
3.
Check “RKE-PANIC” and “RKE OPE COUN1” indications when pressing (for approximately 0.5 seconds)
“PANIC ALARM” button of Intelligent Key.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace Intelligent Key.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Indication
Specification
RKE-PANIC
OFF
→
ON
RKE OPE COUN1
Increases
Revision: 2013 February
2012 Murano CrossCabriolet
SEC-108
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
KEY SLOT
REMOVAL AND INSTALLATION
KEY SLOT
Exploded View
INFOID:0000000007563345
Removal and Installation
INFOID:0000000007563346
REMOVAL
1.
Remove the instrument lower panel LH (2). Refer to
2.
Disconnect key slot connector.
3.
Remove the key slot mounting screw (A), and then remove key
slot (1) from instrument lower panel LH (2).
INSTALLATION
Install in the reverse order of removal.
1.
Key slot
2.
Instrument lower panel LH
JMKIA1820ZZ
JMKIA1821ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
PUSH-BUTTON IGNITION SWITCH
SEC-109
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
PUSH-BUTTON IGNITION SWITCH
Exploded View
INFOID:0000000007563347
Removal and Installation
INFOID:0000000007563348
REMOVAL
1.
Remove the instrument stay cover LH. Refer to
IP-13, "Removal and Installation"
.
2.
Remove the push-button ignition switch (1) from instrument stay
cover LH, after removing pawl (A). Press push-button ignition
switch (1) back to disengage from instrument stay cover LH (2).
INSTALLATION
Install in the reverse order of removal.
1.
Push-button ignition switch
JMKIA1812ZZ
JMKIA1813ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
SEC-110
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
SECURITY INDICATOR LAMP
SECURITY INDICATOR LAMP
Exploded View
INFOID:0000000007563349
Removal and Installation
INFOID:0000000007563350
REMOVAL
Remove the security indicator lamp (1).
•
Disengage pawls with remover tool (A) and pull up the security
indicator lamp.
INSTALLATION
Install in the reverse order of removal.
1.
Security indicator lamp
JMKIA1830ZZ
: Pawl
JMKIA1831ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст