Murano Cross Cabriolet Z51 (2012 year). Manual — part 94
SRC-144
< DTC/CIRCUIT DIAGNOSIS >
B1264 DOOR-MOUNTED CURTAIN AIR BAG MODULE LH
B1264 DOOR-MOUNTED CURTAIN AIR BAG MODULE LH
Description
INFOID:0000000007564734
In case of side collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
INFOID:0000000007564735
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-144, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564736
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1264
FR-LH DOOR MNT
MODULE
[GND-SHORT]
Door-mounted curtain air bag module LH
circuit is shorted to ground
• Disconnection of wiring harness and short
• Malfunction in door-mounted curtain air bag
module LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 February
2012 Murano CrossCabriolet
B1264 DOOR-MOUNTED CURTAIN AIR BAG MODULE LH
SRC-145
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
4.
REPLACE DOOR-MOUNTED CURTAIN AIR BAG MODULE
1.
Replace door-mounted curtain air bag module LH. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 February
2012 Murano CrossCabriolet
SRC-146
< DTC/CIRCUIT DIAGNOSIS >
B1265 DOOR-MOUNTED CURTAIN AIR BAG MODULE LH
B1265 DOOR-MOUNTED CURTAIN AIR BAG MODULE LH
Description
INFOID:0000000007564737
In case of side collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
INFOID:0000000007564738
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-146, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564739
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1265
FR-LH DOOR MNT
MODULE
[SHORT]
Door-mounted curtain air bag module LH cir-
cuits are shorted to each other
• Disconnection of wiring harness and short
• Malfunction in door-mounted curtain air bag
module LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 February
2012 Murano CrossCabriolet
B1265 DOOR-MOUNTED CURTAIN AIR BAG MODULE LH
SRC-147
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
4.
REPLACE DOOR-MOUNTED CURTAIN AIR BAG MODULE
1.
Replace door-mounted curtain air bag module LH. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 February
2012 Murano CrossCabriolet
SRC-148
< DTC/CIRCUIT DIAGNOSIS >
B1289 POP-UP ROLL BAR RH
B1289 POP-UP ROLL BAR RH
Description
INFOID:0000000007564740
When diagnosis sensor unit detects acceleration that the vehicle rolls over in the lateral direction, pop-up roll
bar is activated so that the heads of rear passengers are protected.
DTC Logic
INFOID:0000000007564741
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-148, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564742
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE POP-UP ROLL BAR
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1289
RH POP-UP BAR
[OPEN]
Pop-up roll bar RH circuit is open
• Disconnection of wiring harness and open
• Malfunction in pop-up roll bar RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 February
2012 Murano CrossCabriolet
B1289 POP-UP ROLL BAR RH
SRC-149
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
1.
Replace pop-up roll bar RH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 February
2012 Murano CrossCabriolet
SRC-150
< DTC/CIRCUIT DIAGNOSIS >
B1290 POP-UP ROLL BAR RH
B1290 POP-UP ROLL BAR RH
Description
INFOID:0000000007564743
When diagnosis sensor unit detects acceleration that the vehicle rolls over in the lateral direction, pop-up roll
bar is activated so that the heads of rear passengers are protected.
DTC Logic
INFOID:0000000007564744
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-150, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564745
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE POP-UP ROLL BAR
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1290
RH POP-UP BAR
[VB-SHORT]
Pop-up roll bar RH circuit is shorted to
power supply circuit
• Disconnection of wiring harness and short
• Malfunction in pop-up roll bar RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 February
2012 Murano CrossCabriolet
B1290 POP-UP ROLL BAR RH
SRC-151
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
1.
Replace pop-up roll bar RH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 February
2012 Murano CrossCabriolet
SRC-152
< DTC/CIRCUIT DIAGNOSIS >
B1291 POP-UP ROLL BAR RH
B1291 POP-UP ROLL BAR RH
Description
INFOID:0000000007564746
When diagnosis sensor unit detects acceleration that the vehicle rolls over in the lateral direction, pop-up roll
bar is activated so that the heads of rear passengers are protected.
DTC Logic
INFOID:0000000007564747
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-152, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564748
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE POP-UP ROLL BAR
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1291
RH POP-UP BAR
[GND-SHORT]
Pop-up roll bar RH circuit is shorted to
ground
• Disconnection of wiring harness and short
• Malfunction in pop-up roll bar RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 February
2012 Murano CrossCabriolet
B1291 POP-UP ROLL BAR RH
SRC-153
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
1.
Replace pop-up roll bar RH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 February
2012 Murano CrossCabriolet
SRC-154
< DTC/CIRCUIT DIAGNOSIS >
B1292 POP-UP ROLL BAR RH
B1292 POP-UP ROLL BAR RH
Description
INFOID:0000000007564749
When diagnosis sensor unit detects acceleration that the vehicle rolls over in the lateral direction, pop-up roll
bar is activated so that the heads of rear passengers are protected.
DTC Logic
INFOID:0000000007564750
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-154, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564751
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE POP-UP ROLL BAR
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1292
RH POP-UP BAR
[SHORT]
Pop-up roll bar RH circuits are shorted to
each other
• Disconnection of wiring harness and short
• Malfunction in pop-up roll bar RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 February
2012 Murano CrossCabriolet
B1292 POP-UP ROLL BAR RH
SRC-155
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
1.
Replace pop-up roll bar RH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 February
2012 Murano CrossCabriolet
SRC-156
< DTC/CIRCUIT DIAGNOSIS >
B1294 POP-UP ROLL BAR LH
B1294 POP-UP ROLL BAR LH
Description
INFOID:0000000007564752
When diagnosis sensor unit detects acceleration that the vehicle rolls over in the lateral direction, pop-up roll
bar is activated so that the heads of rear passengers are protected.
DTC Logic
INFOID:0000000007564753
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-156, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564754
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE POP-UP ROLL BAR
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1294
LH POP-UP BAR
[OPEN]
Pop-up roll bar LH circuit is open
• Disconnection of wiring harness and open
• Malfunction in pop-up roll bar LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 February
2012 Murano CrossCabriolet
B1294 POP-UP ROLL BAR LH
SRC-157
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
1.
Replace pop-up roll bar LH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 February
2012 Murano CrossCabriolet
SRC-158
< DTC/CIRCUIT DIAGNOSIS >
B1295 POP-UP ROLL BAR LH
B1295 POP-UP ROLL BAR LH
Description
INFOID:0000000007564755
When diagnosis sensor unit detects acceleration that the vehicle rolls over in the lateral direction, pop-up roll
bar is activated so that the heads of rear passengers are protected.
DTC Logic
INFOID:0000000007564756
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-158, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564757
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE POP-UP ROLL BAR
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1295
LH POP-UP BAR
[VB-SHORT]
Pop-up roll bar LH circuit is shorted to
power supply circuit
• Disconnection of wiring harness and short
• Malfunction in pop-up roll bar LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 February
2012 Murano CrossCabriolet
B1295 POP-UP ROLL BAR LH
SRC-159
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
1.
Replace pop-up roll bar LH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 February
2012 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст