Nissan Murano Z50 (2004 year). Manual — part 34
NVIS (NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)
BL-137
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2004 November
2004 Murano
4.
PERFORM INITIALIZATION WITH CONSULT-II AGAIN
1.
Replace BCM.
2.
Perform initialization with CONSULT-II.
For initialization, refer to “CONSULT-II Operation Manual NATS-
IVIS/NVIS”.
NOTE:
If the initialization is not completed or malfunctions, CONSULT-II
shows the message on the screen.
Can the system be initialized?
Yes
>> System is OK. (BCM is malfunctioning. Ref. part No. A )
No
>> ECM is malfunctioning.
●
Replace ECM. Ref. part No. B
●
Perform initialization with CONSULT-II.
●
For initialization, refer to “CONSULT-II Operation
Manual NATS-IVIS/NVIS”.
How to Replace NATS Antenna Amp.
AIS002L5
NOTE:
●
If NATS antenna amp. is not installed correctly, NVIS (NATS)
system will not operate properly and SELF-DIAG RESULTS
on CONSULT-II screen will show “LOCK MODE” or “CHAIN
OF IMMU-KEY”.
●
Initialization is not necessary only when NATS antenna
amp. is replaced with a new one.
SEL297W
SIIA1683E
BL-138
INTEGRATED HOMELINK TRANSMITTER
Revision: 2004 November
2004 Murano
INTEGRATED HOMELINK TRANSMITTER
PFP:96401
Wiring Diagram —TRNSCV—
AIS002WQ
TIWA0443E
INTEGRATED HOMELINK TRANSMITTER
BL-139
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2004 November
2004 Murano
Trouble Diagnoses
AIS002WR
DIAGNOSTIC PROCEDURE
SYMPTOM: Transmitter Does Not Activate Receiver
Before conducting the procedure given below, make sure that system receiver (garage door opener, etc.)
operates with original, hand-held transmitter. If NG, receiver or hand-held transmitter is malfunctioning, not
vehicle related.
1.
CHECK ILLUMINATION
1.
Turn ignition switch “OFF”.
2.
Does red light (LED) of transmitter illuminate when any transmit-
ter button is pressed?
YES or NO
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK TRANSMITTER
Check transmitter with Tool*.
*:For details, refer to Technical Service Bulletin.
OK or NG
OK
>> Receiver or hand-held transmitter malfunction, not vehicle related.
NG
>> Replace inside mirror assembly.
3.
CHECK POWER SUPPLY
1.
Disconnect transmitter connector.
2.
Turn ignition switch “OFF”.
3.
Check voltage between auto anti-dazzling inside mirror (integrated homelink transmitter) connector R4
terminal 5 (Y) and ground.
OK or NG
OK
>> GO TO 4.
NG
>>
●
Check 10A fuse. [No. 19 located in the fuse block (J/
B)]
●
Repair or replace harness between fuse and anti-daz-
zling inside mirror (integrated homelink transmitter).
PIIA4815E
5 (Y) – Ground
: Battery voltage
PIIA2370E
BL-140
INTEGRATED HOMELINK TRANSMITTER
Revision: 2004 November
2004 Murano
4.
CHECK GROUND CIRCUIT
Check continuity between anti-dazzling inside mirror (integrated
homelink transmitter) connector R4 terminal 8 (B) and ground.
OK or NG
OK
>> Replace inside mirror assembly.
NG
>> Harness for open or short between anti-dazzling inside
mirror (integrated homelink transmitter) ground.
8 (B) – Ground
:Continuity should exist.
PIIA2368E
BODY REPAIR
BL-141
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2004 November
2004 Murano
BODY REPAIR
PFP:60100
Body Exterior Paint Color
AIS001XT
2S:Solid + Clear,
M:Metallic, 2P:2-Coat pearl, 3P:3-Coat pearl, FM: Iron oxide metallic
SIIA2069E
Component
Color code
BBW9
BC15
BE12
BKH3
BKY0
BKY2
BQX1
BR10
Description
Dark
Blue
Brown
Light
Gold
Black
Silver
Gray
White
Orange
Paint type
2P
FM
M
2S
M
M
3P
M
Hard clear coat
×
×
-
×
-
-
-
-
1 Bumper fascia
Upper
Body color
BBW9
BC15
BE12
BKH3
BKY0
BKY2
BQX1
BR10
Lower
Gray Metallic (M)
BKR2
BKR2
BKR2
BKR2
BKR2
BKR2
BKR2
BKR2
2 Front grille
Chromium-plate +
Color clear coat
Cr2p
Cr2p
Cr2p
Cr2p
Cr2p
Cr2p
Cr2p
Cr2p
3 Door outside
mirror
Housing
Body color
BBW9
BC15
BE12
BKH3
BKY0
BKY2
BQX1
BR10
Base
Black
BKH3
BKH3
BKH3
BKH3
BKH3
BKH3
BKH3
BKH3
4 Door outside
handle
Chromium-plate
Cr2p
Cr2p
Cr2p
Cr2p
Cr2p
Cr2p
Cr2p
Cr2p
Body color
BBW9
BC15
BE12
BKH3
BKY0
BKY2
BQX1
BR10
5 Back door
Body color
BBW9
BC15
BE12
BKH3
BKY0
BKY2
BQX1
BR10
BL-142
BODY REPAIR
Revision: 2004 November
2004 Murano
Body Component Parts
AIS001XU
UNDERBODY COMPONENT PARTS
SIIA2388E
BODY REPAIR
BL-143
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2004 November
2004 Murano
1.
Hoodledge assembly
23. Rear floor side
2.
Upper hoodledge
24. Spare tire clamp bracket
3.
Lower front hoodledge
25. Front side member assembly
4.
Hoodledge reinforcement
26. Front side member
5.
Air box assembly
27. Front side member connector
6.
Side cowl top
28. Bumper stay reinforcement assembly
7.
Lower dash
29. Front suspension mounting bracket
8.
Side dash
30. Front side member outrigger assembly
9.
Front floor
31. Lower dash crossmember
10. Center front floor reinforcement
32. Front side member closing plate assembly
11. Front floor reinforcement (RH&LH)
33. Front side member front closing plate
12. Front side member stiffener
34. Front side member center extension
13. Center floor member assembly
35. Front side member rear extension
14. Inner sill
36. Rear seat crossmember
15. 2ND crossmember assembly
37. Rear side member assembly
16. 3RD crossmember assembly
38. Inner sill extension
17. Rear floor
39. Jack up point bracket
18. Rear floor rear
40. Sill closing plate
19. Rear floor front extension
41. Rear side member extension
20. Rear seat back support assembly
42. Center rear crossmember assembly
21. Outer rear seat belt anchor reinforcement
43. Spare wheel crossmember
22. 2ND seat mounting bracket
BL-144
BODY REPAIR
Revision: 2004 November
2004 Murano
BODY COMPONENT PARTS
1.
Hood
24. Rear roof rail assembly
2.
Front fender (RH&LH)
25. Roof bow No.1
SIIA2389E
BODY REPAIR
BL-145
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2004 November
2004 Murano
3.
Side body assembly (RH&LH)
26. Roof bow No.2
4.
Outer front side body (RH&LH)
27. Roof bow No.3
5.
Upper pillar hinge brace assembly (RH&LH)
28. Roof bow No.4
6.
Lower front pillar hinge brace (RH&LH)
29. Roof bow No.5
7.
Lower front pillar reinforcement (RH&LH)
30. Rear fender assembly (RH&LH)
8.
Center pillar reinforcement (RH&LH)
31. Rear fender extension (RH&LH)
9.
Outer sill reinforcement assembly (RH&LH)
32. Back pillar assembly (RH&LH)
10. Rear outer sill reinforcement (RH&LH)
33. Rear combination lamp base assembly (RH&LH)
11. Outer sill (RH&LH)
34. Rear bumper fascia rear bracket (RH&LH)
12. Inner side roof rail (RH&LH)
35. Rear combination lamp base extension (RH&LH)
13. Inner center pillar (RH&LH)
36. Fuel filler lid (LH)
14. Inner rear pillar assembly (RH&LH)
37. Rear panel assembly
15. Inner rear pillar reinforcement (RH&LH)
38. Rear bumper fascia bracket
16. Back pillar reinforcement (RH&LH)
39. Front door assembly (RH&LH)
17. Outer rear wheelhouse (RH&LH)
40. Outer front door panel (RH&LH)
18. Inner rear wheelhouse assembly (RH&LH)
41. Rear door assembly (RH&LH)
19. Inner rear wheelhouse front extension (RH&LH)
42. Outer rear door panel (RH&LH)
20. Inner rear wheelhouse rear extension (RH&LH)
43. Front bumper reinforcement
21. Roof
44. Front bumper stay (RH&LH)
22. Roof assembly (for sunroof)
45. Rear bumper reinforcement
23. Front roof rail assembly
46. Rear bumper stay (RH&LH)
BL-146
BODY REPAIR
Revision: 2004 November
2004 Murano
Corrosion Protection
AIS001XV
DESCRIPTION
To provide improved corrosion prevention, the following anti-corrosive measures have been implemented in
NISSAN production plants. When repairing or replacing body panels, it is necessary to use the same anti-cor-
rosive measures.
Anti-corrosive Precoated Steel (Galvannealed Steel)
To improve repairability and corrosion resistance, a new type of anti-
corrosive precoated steel sheet has been adopted replacing conven-
tional zinc-coated steel sheet.
Galvannealed steel is electroplated and heated to form Zinc-iron
alloy, which provides excellent and long term corrosion resistance
with cationic electrodeposition primer.
Nissan Genuine Service Parts are fabricated from galvannealed steel. Therefore, it is recommended that
GENUINE NISSAN PARTS or equivalent be used for panel replacement to maintain the anti-corrosive perfor-
mance built into the vehicle at the factory.
Phosphate Coating Treatment and Cationic Electrodeposition Primer
A phosphate coating treatment and a cationic electrodeposition primer, which provide excellent corrosion pro-
tection, are employed on all body components.
CAUTION:
Confine paint removal during welding operations to an absolute
minimum.
Nissan Genuine Service Parts are also treated in the same manner. Therefore, it is recommended that GENU-
INE NISSAN PARTS or equivalent be used for panel replacement to maintain anti-corrosive performance built
into the vehicle at the factory.
SIIA2294E
PIIA0095E
BODY REPAIR
BL-147
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2004 November
2004 Murano
ANTI-CORROSIVE WAX
To improve corrosion resistance, anti-corrosive wax is applied inside the body sill and inside other closed sec-
tions. Accordingly, when replacing these parts, be sure to apply anti-corrosive wax to the appropriate areas of
the new parts. Select an excellent anti-corrosive wax which will penetrate after application and has a long shelf
life.
SIIA2160E
BL-148
BODY REPAIR
Revision: 2004 November
2004 Murano
UNDERCOATING
The underside of the floor and wheelhouse are undercoated to prevent rust, vibration, noise and stone chip-
ping. Therefore, when such a panel is replaced or repaired, apply undercoating to that part. Use an undercoat-
ing which is rust preventive, soundproof, vibration-proof, shock-resistant, adhesive, and durable.
Precautions in Undercoating
1.
Do not apply undercoating to any place unless specified (such as the areas above the muffler and three
way catalyst which are subjected to heat).
2.
Do not undercoat the exhaust pipe or other parts which become hot.
3.
Do not undercoat rotating parts.
4.
Apply bitumen wax after applying undercoating.
5.
After putting seal on the vehicle, put undercoating on it.
SIIA2161E
BODY REPAIR
BL-149
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2004 November
2004 Murano
STONE GUARD COAT
To prevent damage caused by stones, the lower outer body panel (fender, door, etc.) have an additional layer
of Stone Guard Coating over the ED primer coating. When replacing or repairing these panels, apply Stone
Guard coating to the same portions as before. Use a coating which is rust preventive, durable, shock-resistant
and has a long shelf life.
SIIA2162E
BL-150
BODY REPAIR
Revision: 2004 November
2004 Murano
Body Sealing
AIS001XW
DESCRIPTION
The following figure shows the areas which are sealed at the factory. Sealant which has been applied to these
areas should be smooth and free from cuts or gaps. Care should be taken not to apply an excess amount of
sealant and not to allow other unaffected parts to come into contact with the sealant.
SIIA2163E
BODY REPAIR
BL-151
C
D
E
F
G
H
J
K
L
M
A
B
BL
Revision: 2004 November
2004 Murano
SIIA2164E
BL-152
BODY REPAIR
Revision: 2004 November
2004 Murano
SIIA2165E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст