Nissan Murano Z50 (2004 year). Manual — part 134
GW-80
REAR WINDOW DEFOGGER
Revision: 2004 November
2004 Murano
6.
CHECK REAR WINDOW DEFOGGER RELAY OUTPUT SIGNAL
1.
Connect IPDM E/R and rear window defogger relay.
2.
Turn ignition switch ON.
3.
Check voltage between IPDM E/R connector E9 terminal 52 and ground.
OK or NG
OK
>> Replace IPDM E/R.
NG
>> Check the condition of the harness and the connector.
Rear Window Defogger Circuit Check
AIS002IN
1.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect rear window defogger connector.
3.
Turn ignition switch ON.
4.
Check voltage between rear window defogger connector and ground.
OK or NG
OK
>> GO TO 2.
NG
>> GO TO 3.
2.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between rear window defogger connector D107 terminal 2 and ground.
OK or NG
OK
●
If filament is OK.
Check the condition of the harness and the connector.
●
If filament is NG.
Repair filament.
NG
>> Repair or replace harness between rear window defog-
ger and ground.
52 (G/R) – Ground
:Battery voltage
PIIA6210E
Connector
Terminal (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
D97
1 (G)
Ground
Rear window defogger
switch ON.
Battery voltage
Rear window defogger
switch OFF.
0
PIIA4234E
2 (B)
−
Ground
: Continuity should exist.
PIIA4235E
REAR WINDOW DEFOGGER
GW-81
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2004 November
2004 Murano
3.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect rear window defogger relay.
3.
Check continuity between rear window defogger relay connector B8 terminal 5 and rear window defogger
connector D97 terminal 1.
OK or NG
OK
>> Check the condition of the harness and the connector.
NG
>> Repair or replace harness rear window defogger relay
and rear window defogger. When there is malfunction
inside back door, replace the back door.
Door Mirror Defogger Power Supply Circuit Check
AIS002IO
1.
CHECK FUSE
Check 10A fuse [No. 8, located in the fuse block (J/B)]
NOTE:
Refer to
GW-65, "Component Parts and Harness Connector Location"
OK or NG
OK
>> GO TO 2.
NG
>> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to
3, "POWER SUPPLY ROUTING CIRCUIT"
.
2.
CHECK POWER SUPPLY CIRCUIT 1
1.
Turn ignition switch ON.
2.
Check voltage between fuse block (J/B) connector and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between rear window defogger relay and fuse block (J/B).
5 (G) – 1 (G)
: Continuity should exist.
PIIA4236E
Connector
Terminal (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
E101
2C (G)
Ground
Rear window defogger
switch ON
Battery voltage
Rear window defogger
switch OFF
0
PIIA2388E
GW-82
REAR WINDOW DEFOGGER
Revision: 2004 November
2004 Murano
3.
CHECK POWER SUPPLY CIRCUIT 2
Check voltage between fuse block (J/B) connector and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Replace fuse block (J/B).
4.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect fuse block (J/B) and door mirror connector.
3.
Check continuity between fuse block (J/B) connector M5 terminal 5B and door mirror connector D2 (driver
side) or D32 (passenger side) terminal 1.
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace harness between fuse block (J/B) and
malfunction door mirror connector.
5.
CHECK GROUND CIRCUIT
Check continuity between each door mirror connector D2 (driver side), D32 (passenger side) terminal 5 and
ground.
OK or NG
OK
>> GO TO 6.
NG
>> Repair or replace harness.
Connector
Terminal (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
M5
5B (L)
Ground
Rear window defogger
switch ON
Battery voltage
Rear window defogger
switch OFF
0
PIIA2386E
5B (B) – 1 (B)
: Continuity should exist.
PIIA4228E
5 (B) – Ground
: Continuity should exist.
PIIA4229E
REAR WINDOW DEFOGGER
GW-83
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2004 November
2004 Murano
6.
CHECK DOOR MIRROR DEFOGGER
1.
Connector door mirror connector.
2.
Check continuity between each door mirror connector D2 (driver side), D32 (passenger side) terminals 1
and 5.
OK or NG
OK
>> Check the condition of the harness and the connector.
NG
>> Replace malfunctioning door mirror.
Driver Side Door Mirror Defogger Circuit Check
AIS002IP
1.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect door mirror (driver side) connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror (driver side) connector and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace harness between fuse block (J/B) and
door mirror (driver side).
2.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror (driver side) connector D2
terminal 5 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between door mirror (driver
side) and ground.
1 (L/B) – 5 (L/B)
: Continuity should exist.
PIIA4230E
Connector
Terminal (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
D2
1 (L/B)
Ground
Rear window defogger
switch ON
Battery voltage
Rear window defogger
switch OFF
0
PIIA4231E
5 (B) – Ground
: Continuity should exist.
PIIA4229E
GW-84
REAR WINDOW DEFOGGER
Revision: 2004 November
2004 Murano
3.
CHECK DOOR MIRROR DEFOGGER
1.
Connector door mirror connector.
2.
Check continuity between each door mirror connector D2 (driver side) terminals 1 and 5.
OK or NG
OK
>> Check the condition of the harness and the connector.
NG
>> Replace door mirror (driver side).
Passenger Side Door Mirror Defogger Circuit Check
AIS002IQ
1.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect door mirror (passenger side) connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror (passenger side) connector and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace harness between fuse block (J/B) and
door mirror (passenger side).
2.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror (passenger side) connector D32 terminal 5 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between door mirror (passen-
ger side) and ground.
1 (L/B) – 5 (L/B)
: Continuity should exist.
PIIA4230E
Connector
Terminal (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
D32
1 (L/B)
Ground
Rear window defogger
switch ON
Battery voltage
Rear window defogger
switch OFF
0
PIIA4231E
5 (B) – Ground
: Continuity should exist.
PIIA4229E
REAR WINDOW DEFOGGER
GW-85
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2004 November
2004 Murano
3.
CHECK DOOR MIRROR DEFOGGER
1.
Connector door mirror connector.
2.
Check continuity between each door mirror connector D32 (passenger side) terminals 1 and 5.
OK or NG
OK
>> Check the condition of the harness and the connector.
NG
>> Replace door mirror (passenger side).
Rear Window Defogger Signal Check
AIS002J2
1.
CHECK REAR WINDOW DEFOGGER SWITCH LAMP
A/C and AV switch self-diagnosis is executed. Refer to
AV-92, "A/C and AV Switch Self-Diagnosis Function"
OK or NG
OK
>> GO TO 2.
NG
>> Replace A/C and AV switch.
2.
CHECK AV COMMUNICATION LINE
AV communication line check is executed. Refer to
AV-100, "A/C and AV Switch Does Not Operate"
OK or NG
OK
>> GO TO 3.
NG
>> Replace display control unit.
3.
CHECK CAN COMMUNICATION LINE
CAN communication line check is executed. Refer to
AV-101, "CAN Communication Line Check"
OK or NG
OK
>> Check the condition of the harness and the connector.
NG
>> In addition, it is necessary to check CAN communication line. Refer to
1 (L/B) – 5 (L/B)
: Continuity should exist.
PIIA4230E
Does rear window defogger switch light?
Is rear window defogger displayed on the display?
GW-86
REAR WINDOW DEFOGGER
Revision: 2004 November
2004 Murano
Filament Check
AIS002IR
1.
When measuring voltage, wrap tin foil around the top of the neg-
ative probe. Then press the foil against the wire with your finger.
2.
Attach probe circuit tester (in Volt range) to middle portion of
each filament.
3.
If a filament is burned out, circuit tester registers 0 or battery
voltage.
4.
To locate burned out point, move probe to left and right along fil-
ament. Test needle will swing abruptly when probe passes the
point.
Filament Repair
AIS002IS
REPAIR EQUIPMENT
●
Conductive silver composition (Dupont No. 4817 or equivalent)
●
Ruler 30 cm (11.8 in) long
●
Drawing pen
●
Heat gun
●
Alcohol
●
Cloth
SEL122R
SEL263
SEL265
REAR WINDOW DEFOGGER
GW-87
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2004 November
2004 Murano
REPAIRING PROCEDURE
1.
Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.
2.
Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use.
3.
Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
4.
After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.
5.
Apply a constant stream of hot air directly to the repaired area
for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.
PIIA0215E
SEL012D
SEL013D
GW-88
DOOR MIRROR
Revision: 2004 November
2004 Murano
DOOR MIRROR
PFP:96301
Automatic Drive Positioner Interlocking Door Mirror
AIS003I3
Automatic drive positioner interlocking door mirror. Refer to
DOOR MIRROR
GW-89
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2004 November
2004 Murano
Power Door Mirror (Only Manual Operation Model)
AIS001T2
WIRING DIAGRAM –MIRROR–
TIWA0348E
GW-90
DOOR MIRROR
Revision: 2004 November
2004 Murano
Removal and Installation
AIS001T3
CAUTION:
Be careful not to damage the mirror bodies.
REMOVAL
1.
Remove the front door finisher. Refer to
2.
Remove the front door sash cover.
3.
Remove the door mirror harness connector.
4.
Remove the door mirror mounting nuts, and remove the door mirror assembly.
INSTALLATION
Install in the reverse order of removal.
Disassembly and Assembly
AIS004VX
DISASSEMBLY
1.
Place the mirror body with mirror glass facing upward.
2.
Put a strip of protective tape on mirror body.
3.
As shown in the figure insert a small slotted screwdriver into the
recess between mirror base (mirror holder) and mirror holder
bracket and push up two pawls to remove mirror holder lower
half side.
NOTE:
When pushing up pawls do not attempt to use one recess only,
be sure to push up with both recesses.
Insert screwdriver into recesses, and push up while rotating
(twist) to make work easier.
4.
Remove two terminals of mirror heater attachment.
5.
Lightly lift up lower side of mirror surface from mirror surface, and detach two pawls of upper side as if
pulling it out. Remove mirror surface from mirror body.
1.
Door mirror assembly
2.
Front door sash cover
PIIA4001E
PIIA4002E
DOOR MIRROR
GW-91
C
D
E
F
G
H
J
K
L
M
A
B
GW
Revision: 2004 November
2004 Murano
NOTE:
Be certain not to allow grease on sealing agent in center of mirror body assembly (actuator) or back side
of mirror surface (mirror holder).
ASSEMBLY
1.
Place mirror holder bracket and mirror body assembly (actuator) in a horizontal position.
2.
Connect two terminals of heater installed mirror.
3.
Fit the upper two pawls on the mirror face onto the mirror holder
bracket first, then press the lower side of mirror face until a click
sound is heard to engage the lower pawls.
NOTE:
After installation, visually make sure lower two pawls are
securely engaged from the bottom of mirror face.
PIIA4003E
GW-92
DOOR MIRROR
Revision: 2004 November
2004 Murano
IDX-1
A
C
D
E
F
G
H
I
J
K
L
B
IDX
ALPHABETICAL INDEX
M INDEX
SECTION
IDX
IDX-2
ALPHABETICAL INDEX
A
A/C air flow . . . . . . . . . . . . . ..
A/C component layout . . . . . . . . . .
A/C compressor clutch removal and installation . . ...
A/C compressor mounting . . . . . . . .
A/C compressor precaution . . . . . . . .
A/C compressor special service tool . . . .
A/C control operation (auto A/C) . . . . . ..
A/C diagnostic work flow (auto A/C) . . . .
A/C evaporator . . . . . . . . . . . ...
A/C HFC134a (R134a) system precaution . .
A/C HFC134a (R134a) system service procedure . ...
A/C HFC134a (R134a) system service tools ...
A/C HFC134a system service equipment precaution ...
A/C lubricant (R134a) . . . . . . . . . ..
A/C lubrication oil . . . . . . . . . . ...
A/C operational check . . . . . . . . . ..
A/C self-diagnoses (auto A/C) . . ..
,
A/C service data specification . . . . . .
A/C system description (auto A/C) . . . . ...
A/C trouble diagnoses (auto A/C) . . . . .
A/C, A - Wiring diagram . . . . . . . . ...
ABS - Wiring diagram . . . . . . . . . .
Accelerator control system . . . . . . . ...
Accelerator pedal position (APP) sensor . .
Accelerator pedal released position learning . .
,
,
AF1HB1-Wiring diagram . . . . . . . . ..
AF1HB2-Wiring diagram . . . . . . . . ..
Air bag . . . . . . . . . . . . . . . ..
Air bag disposal . . . . . . . . . . . ..
Air bag precautions . . . . . . . . .
Air bleeding for brake system . . . . . . .
Air cleaner and air duct . . . . . . . . . .
Air cleaner filter replacement . . . . . . .
Air conditioner cut control . . . . . . . . ..
Air flow meter - See Mass air flow sensor . ..
,
Air fuel ratio sensor 1 heater . . . . . . .
Air mix. door motor . . . . . . .
Ambient sensor . . . . . . . ...
Angular tightening application . . . . . . . .
APPS1 - Wiring diagram . . . . . . . . ..
APPS2 - Wiring diagram . . . . . . . . ..
APPS3 - Wiring diagram . . . . . . . . ..
ASC/BS - Wiring diagram . . . . . . . .
ASC/SW - Wiring diagram . . . . . . . ...
ASCBOF - Wiring diagram . . . . . . . ...
ASCD . . . . . . . . . . . . . . . ...
ASCD (automatic speed control device) . . ...
ASCIND - Wiring diagram . . . . . . . .
AUDIO - Wiring diagram . . . . . . . . .
Auto air conditioner - Wiring diagram . . . .
Auto amp . . . . . . . . . . . . . ..
Auto anti-dazzling inside mirror . . ..
Automatic transmission fluid replacement . .
AV and NAVI control unit . . . . . . . . .
AV communication line . . . . . .
AWD - Wiring diagram . . . . . . . . . ...
AWD control unit inspection table . . . . . ..
Axle . . . . . . . . . . . . . . . . ...
B
Back Door . . . . . . . . . . . ...
Back door . . . . . . . . . . . .
Back door opener - See Back door . . . . .
BACK/L - Wiring diagram . . . . . . . . .
Back-up lamp . . . . . . . . . . . . ...
Battery . . . . . . . . . . . . . . . . .
Battery/Starting/Charging System Tester
,
BCM (Body control module) . . . . . . . ..
Blower motor . . . . . . . . ...
Blower unit . . . . . . . . . . . . .
Board computer . . . . . . . . . . . . .
Boring/horning cylinder block . . . . . . ..
Bose speaker amp. . . . . . . . . . . . ..
Brake booster . . . . . . . . . . . . .
Brake fluid change . . . . . . . . . . . .
Brake fluid level . . . . . . . . . . . .
Brake fluid level and line check . . . . . . .
Brake hydraulic line . . . . . . . . . . ...
Brake inspection . . . . . . . . . . . ...
Brake lines and cables inspection . . . . .
Brake master cylinder . . . . . . . . . .
Brake pedal . . . . . . . . . . . . . . ..
Brake switch . . . . . . . . . . . . .
BRK/SW - Wiring diagram . . . . . . . ...
Bulb specifications . . . . . . . . . . ...
Bumper, front . . . . . . . . . . . . . ..
Bumper, rear . . . . . . . . . . . . . ...
C
Camshaft . . . . . . . . . . . . . . ..
Camshaft inspection . . . . . . . . . . .
Camshaft position sensor (PHASE) . . . . .
,
,
,
,
CAN (Controller Area Network) ...
,
,
,
,
IDX-3
A
C
D
E
F
G
H
I
J
K
L
B
IDX
ALPHABETICAL INDEX
,
,
,
,
,
,
,
Canister-See EVAP canister . . . . . . ...
CHARGE - Wiring diagram . . . . . . . .
Charging system . . . . . . . . . . . .
Chassis and body maintenance . . . . . .
CHIME - Wiring diagram . . . . . . . . . .
CIGAR - Wiring diagram . . . . . . . . ..
Circuit breaker . . . . . . . . . . . . ...
Closed loop control . . . . . . . . . . .
Collision diagnosis . . . . . . . . . . ...
Combination lamp, front, removal and installation . .
Combination lamp, rear, removal and installation . .
Combination meter . . . . . . . . . . . ...
Combination meter removal and installation - See
Instrument panel . . . . . . . . . . . . ..
COMM - Wiring diagram . . . . . ..
COMPAS - Wiring diagram . . . . . . . . .
Compass . . . . . . . . . . . . . . .
Component Location (auto A/C) . . . . . ..
Compression pressure . . . . . . . . . ..
Compressor clutch removal and installation ..
Compressor special service tool . . . . . ..
Condenser . . . . . . . . . . . . . .
Connecting rod . . . . . . . . . . . .
Connecting rod bearing clearance . . . . ...
Connecting rod bushing clearance . . . . ..
Console box - See Instrument panel . . . . ...
Console box lamp . . . . . . . . . . . .
CONSULT-II Reference value (CVT) . . . ..
Control units (terminal arrangement) . . . . .
Control valve (CVT) . . . . . . . . . . .
Controller Area Network (CAN) ..
,
,
,
,
,
,
COOL/F - Wiring diagram . . . . . . . .
Coolant replacement . . . . . . . . . . .
Coolant replacementVQ35DE . . . . . . . .
Cooling circuit (engine) . . . . . . . . . .
Cooling fan . . . . . . . . . . . . . .
Cooling fan motor . . . . . . . . . . .
Cowl top . . . . . . . . . . . . . . . ...
Cowl top cover . . . . . . . . . . . . . .
Crankcase ventilation system - See Positive crankcase
ventilation . . . . . . . . . . . . . .
Crankshaft . . . . . . . . . . . . . ...
Crankshaft position sensor (POS) . . . . ...
Crash zone sensor . . . . . . . . . . ..
CVT air breather hose . . . . . . . . ...
CVT control system . . . . . . . . . . .
CVT cross-sectional view . . . . . . . .
CVT Electrical parts location . . . .
CVT fluid checking . . . .
,
CVT fluid cooler cleaning . . . . . . . . .
CVT fluid cooler valve . . . . . . . . .
CVT fluid replacement . . . . . .
,
CVT fluid temparature sensor . . . . . . ..
CVT hydraulic control system . . . . . . ..
CVT indicator . . . . . . . . . . . . . ..
CVT self-diagnoses . . . . . . ..
CVT shift lock system . . . . . . . . .
CVT shift lock system - Wiring diagram . . .
CVT trouble diagnoses . . . . . . . . .
CVTIND - Wiring diagram . . . . . . . . ...
Cylinder block . . . . . . . . . . . . .
Cylinder head . . . . . . . . . . . . .
Cylinder head bolt tightening . . . . . . .
D
Daytime light system . . . . . . . . . . ...
Daytime running light - See Daytime light system
Diagnosis sensor unit . . . . . . . . . .
Diagnostic trouble code (DTC) for OBD system ..
Diagnostic trouble code (DTC) inspection priority chart
Differentil side oil seal . . . . . . . . .
Display and amp.assembly . . . ...
Door glass . . . . . . . . . . ...
Door glass Fitting Adjustment(Front) . . . .
Door glass Fitting Adjustment(Rear) . . . . .
Door lock . . . . . . . . . . . . . . .
Door mirror . . . . . . . . . . . . . .
Door trim . . . . . . . . . . . . . . . .
Door, front . . . . . . . . . . . .
Door, rear . . . . . . . . . . . ..
Drive belt . . . . . . . . . . . . . . ...
Drive shaft . . . . . . . . . . . . . . .
Drive shaft (rear) . . . . . . . . . . . ...
Driver air bag . . . . . . . . . . . . ..
DTRL - Wiring diagram . . . . . . . . . ...
Duct and grilles . . . . . . . . . . . ..
E
ECM power supply . . . . . . . .
ECM/PW - Wiring diagram . . . . . . . ...
ECTS - Wiring diagram . . . . . . . . .
Electric sunroof . . . . . . . . . . . . ..
Electric throttle control actuator . . .
Electrical load signal circuit . . . . . . . ..
Electrical unit . . . . . . . . . . . . . .
Electrical units location . . . . . . . . . ..
Electronic ignition (EI) system . . . . . . ...
EMNT - Wiring diagram . . . . . . . . ...
Engine control module (ECM) . . . . . . ..
Engine control system diagram and chart . . .
Engine coolant . . . . . . . . . . . . .
Engine coolant temperature sensor (ECTS) ...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст