Nissan Murano Z50 (2004 year). Manual — part 198
SUNROOF
RF-17
C
D
E
F
G
H
J
K
L
M
A
B
RF
Revision: 2004 November
2004 Murano
Work Flow
AIS002E7
1.
Check the symptom and customer's requests.
2.
Understand the outline of system. Refer to
.
3.
According to the trouble diagnosis chart, repair or replace the cause of the malfunction. Refer to
"Trouble Diagnosis Chart by Symptom"
4.
Does power window system operate normally? If Yes, GO TO 5, If No, GO TO 3.
5.
INSPECTION END.
8
SB
Vehicle speed signal (2-pulse)
Speedometer operated [When vehicle
speed is approx.40km/ h (25MPH)]
9
W
RAP signal
Ignition switch ON
Battery voltage
Within 45 seconds after ignition switch is
turned to OFF position
Battery voltage
Within approx.45 seconds after ignition
switch OFF while front door LH or RH is
open
0
10
B
Ground
—
0
Termi-
nal
Wire
color
Item
Condition
Voltage (V)
(Approx.)
ELF1080D
RF-18
SUNROOF
Revision: 2004 November
2004 Murano
CONSULT-II Function
AIS002E9
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunction might be detected
in self-diagnosis depending on control unit which carry out CAN communication.
“RETAINED PWR”
1.
Turn ignition switch “OFF”.
2.
Connect “CONSULT-II” to the data link connector.
3.
Turn ignition switch “ON”.
4.
Touch “START (NISSAN BASED VHCL)”.
5.
Touch “BCM”.
If “BCM” is not indicated, go to Refer to “CONSULT-II Data Link
Connector (DLC) Circuit”.
6.
Touch “RETAINED PWR”.
PHIA0096E
MBIB0233E
LIIA0033E
LIIA0163E
SUNROOF
RF-19
C
D
E
F
G
H
J
K
L
M
A
B
RF
Revision: 2004 November
2004 Murano
7.
Select diagnosis mode. “DATA MONITOR”, “ACTIVE TEST” and
“WORK SUPPORT” are available.
Data Monitor
AIS002EA
Active Test
AIS002EB
Work Support
AIS002EC
SEL274W
Monitored item
Description
IGN ON SW
Indicates [ON/OFF] condition of ignition switch.
DOOR SW-DR
Indicates [ON/OFF] condition of driver side door switch.
DDOR SW-AS
Indicates [ON/OFF] condition of passenger side door switch.
Test item
Description
RETAINED PWR
This test is able to supply RAP signal (power) from BCM to power window system and
power sunroof system. Those systems can be operated when turning on “RETAINED
PWR” on CONSULT-II screen even if the ignition switch is turned OFF.
NOTE:
During this test, CONSULT-II can be operated with ignition switch in “OFF”
position.“RETAINED PWR” should be turned “ON” or “OFF” on CONLUST-II
screen when ignition switch in ON. Then turn ignition switch OFF for checking
retained power operation. CONSULT-II might be stuck if “RETAINED PWR” is
turned to “ON” or “OFF” on CONSULT-II screen when ignition switch is OFF.
Work item
Description
RETAINED PWR SET
RAP signal’s power supply period can be changed by mode setting. Selects RAP sig-
nal’s power supply period between two steps.
●
MODE 1 (45 sec.) / MODE 2 (OFF) / MODE 3 (2 min.)
RF-20
SUNROOF
Revision: 2004 November
2004 Murano
Trouble Diagnosis Chart by Symptom
AIS002ED
BCM Power Supply and Ground Circuit Check
AIS00350
First perform the “SELF-DIAG RESULTS” in “BCM” with CONSULT-II, then perform the each trouble
diagnosis of malfunction system indicated “SELF-DIAG RESULTS” of “BCM”. Refer to
Communication Inspection Using CONSULT-II (Self-Diagnosis)"
1.
CHECK FUSE
●
Check 10A fuse [No.1, located in fuse block (J/B)]
●
Check 10A fuse [No. 18, located in fuse block (J/B)]
●
Check 50A fusible link (letter F located in the fuse and fusible link box).
NOTE:
Refer to
RF-10, "Component Parts and Harness Connector Location"
.
OK or NG
OK
>> GO TO 2.
NG
>> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to
3, "POWER SUPPLY ROUTING CIRCUIT"
Symptom
Diagnostic procedure and repair order
Refer to page
Sunroof does not operate.
1. BCM power supply and ground circuit check.
2. Sunroof motor assembly power supply and
ground circuit check.
3. Sunroof switch circuit check 9.
4. Replace the sunroof motor assembly.
Sunroof alone does not go to full close position.
1. Sunroof switch circuit check 1.
Sunroof alone does not go to slide position 1.
1. Sunroof switch circuit check 2.
Sunroof alone does not go to slide position 2.
1. Sunroof switch circuit check 3.
Sunroof alone does not go to slide position 3.
1. Sunroof switch circuit check 4.
Sunroof alone does not go to slide position 4.
1. Sunroof switch circuit check 5.
Sunroof alone does not go to full open position.
1. Sunroof switch circuit check 6.
Sunroof alone does not operate tilt up.
1. Sunroof switch circuit check 7.
Sunroof alone does not operate tilt down.
1. Sunroof switch circuit check 8.
Sunroof does not go to slide position 2, 3 and 4.
1. Sunroof switch circuit check 10.
Sunroof does not go to full closed and slide position 1, 2.
1. Sunroof switch circuit check 11.
Sunroof does not go to full close, full open and slide posi-
tion 4.
1. Sunroof switch circuit check 12.
Retained power operation does not operate properly.
1. Check the retained power operation mode setting.
2. Door switch check.
3. BCM check.
4. Replace sunroof motor assembly.
Motor does not stop at the sunroof fully -open or fully-
closed position.
1. Initialization procedure check.
2. Replace the sunroof motor assembly.
Sunroof does not do the interruption detection.
1. Replace the sunroof motor assembly.
SUNROOF
RF-21
C
D
E
F
G
H
J
K
L
M
A
B
RF
Revision: 2004 November
2004 Murano
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch ON.
2.
Check voltage between BCM connectors M34, M35 terminals 38, 42, 55 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Check BCM power supply circuit for open or short.
3.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM connector M35 terminals 52 and ground.
OK or NG
OK
>> BCM power supply and ground circuit is OK.
NG
>> Check BCM ground circuit for open or short.
38 (R) – Ground
: Battery voltage
42 (GR) – Ground
: Battery voltage
55 (W/B) – Ground
: Battery voltage
PIIA6160E
52 (B) –- Ground
: Continuity should exist.
PIIA9131E
RF-22
SUNROOF
Revision: 2004 November
2004 Murano
Sunroof Motor Assembly Power Supply and Ground Circuit Check
AIS002EE
1.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch ON.
2.
Check voltage between sunroof motor assembly connector R6 terminals 7, 9 and ground.
OK or NG
OK
>> GO TO 2.
NG
>> GO TO 3.
2.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect sunroof motor assembly connector.
3.
Check continuity between sunroof motor assembly connector R6 terminal 10 and ground.
OK or NG
OK
>> Sunroof motor assembly power supply and ground cir-
cuit are OK. Further inspection is necessary. Refer to
symptom chart.
NG
>> Repair or replace harness.
3.
CHECK SUNROOF MOTOR ASSEMBLY POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM and sunroof motor assembly connector.
3.
Check continuity between BCM connector M35 terminals 53, 54 and sunroof motor assembly connector
R6 terminals 7, 9.
4.
Check continuity between BCM connector M35 terminals 53, 54
and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace harness.
7 (L) – Ground
: Battery voltage
9 (W) – Ground
: Battery voltage
PIIA4533E
10 (B) – Ground
: Continuity should exist.
PIIA4534E
53 (W/L) – 9 (W)
: Continuity should exist.
54 (W/R) – 7 (L)
: Continuity should exist.
53 (W/L) – Ground
: Continuity should not exist.
54 (W/R) – Ground
: Continuity should not exist.
PIIA9715E
SUNROOF
RF-23
C
D
E
F
G
H
J
K
L
M
A
B
RF
Revision: 2004 November
2004 Murano
4.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Turn ignition switch ON.
3.
Check voltage between BCM connector M35 terminals 53, 54 and ground.
OK or NG
OK
>> Check condition of the harness and the connector.
NG
>> Replace BCM.
BCM Check
AIS002K8
1.
CHECK RETAINED POWER INPUT SIGNAL
Check voltage between sunroof motor assembly connector and ground.
OK or NG
OK
>> Retained power operation input signal is OK.
NG
>> GO TO 2.
2.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect BCM and sunroof motor assembly connector.
3.
Check continuity between BCM connector M35 terminal 53 and
sunroof motor assembly connector R6 terminal 9.
4.
Check continuity between BCM connector M35 terminal 53 and
ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between BCM and sunroof
motor assembly.
53 (W/L) – Ground
: Battery voltage
54 (W/R) – Ground
: Battery voltage
PIIA6154E
Con-
nector
Terminals (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
R6
9 (W)
Ground
Ignition switch ON
Battery voltage
Within 45 seconds after igni-
tion switch in turned to OFF
position
Battery voltage
Within approx.45 seconds
after ignition switch OFF while
front door LH or RH is open
0
PIIA4506E
53 (W/L) – 9 (W)
: Continuity should exist.
53 (W/L) – Ground
: Continuity should not exist.
PIIA9716E
RF-24
SUNROOF
Revision: 2004 November
2004 Murano
3.
CHECK RETAINED POWER OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM connector and ground.
OK or NG
OK
>> Check condition of the harness and the connector.
NG
>> Replace BCM.
Sunroof Switch Circuit Check 1
AIS002K9
1.
CHECK SUNROOF SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect sunroof switch connector.
3.
Check continuity between sunroof switch terminals 2, 3 and 6.
OK or NG
OK
>> GO TO 2.
NG
>> Replace sunroof switch.
2.
CHECK SUNROOF SWITCH OUTPUT SINGAL
1.
Connect sunroof motor connector.
2.
Turn ignition switch ON.
3.
Check voltage between sunroof motor assembly connector and
ground.
OK or NG
OK
>> Replace sunroof motor assembly.
NG
>> Check the condition of the harness and the connector.
Con-
nector
Terminals (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
M35
53 (W/L)
Ground
Ignition switch ON
Battery voltage
Within 45 seconds after igni-
tion switch in turned to OFF
position
Battery voltage
Within approx.45 seconds
after ignition switch OFF while
front door LH or RH is open
0
PIIA9717E
Terminals
Condition
Continuity
2
3
6
Slide switch
FULL CLOSE position
Yes
Other than above
No
PIIA4511E
Connector
Terminals (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
R6
3 (R)
4 (Y)
Ground
Slide switch
FULL CLOSE position
0
Other than above
Battery voltage
PIIA4509E
SUNROOF
RF-25
C
D
E
F
G
H
J
K
L
M
A
B
RF
Revision: 2004 November
2004 Murano
Sunroof Switch Circuit Check 2
AIS002KA
1.
CHECK SUNROOF SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect sunroof switch connector.
3.
Check continuity between sunroof switch terminals 2 and 6.
OK or NG
OK
>> GO TO 2.
NG
>> Replace sunroof switch.
2.
CHECK SUNROOF SWITCH OUTPUT SINGAL
1.
Connect sunroof switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between sunroof motor assembly connector and
ground.
OK or NG
OK
>> Replace sunroof motor assembly.
NG
>> Check the condition of the harness and the connector.
Sunroof Switch Circuit Check 3
AIS002KB
1.
CHECK SUNROOF SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect sunroof switch connector.
3.
Check continuity between sunroof switch terminals 1, 2 and 6.
OK or NG
OK
>> GO TO 2.
NG
>> Replace sunroof switch.
Terminals
Condition
Continuity
2
6
Slide switch
SLIDE POSITION 1
Yes
Other than above
No
PIIA4514E
Connector
Terminals (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
R6
3 (R)
Ground
Slide switch
SLIDE POSITION 1
0
Other than above
Battery voltage
PIIA4512E
Terminals
Condition
Continuity
1
2
6
Slide switch
FULL CLOSE position
Yes
Other than above
No
PIIA4517E
RF-26
SUNROOF
Revision: 2004 November
2004 Murano
2.
CHECK SUNROOF SWITCH OUTPUT SINGAL
1.
Connect sunroof switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between sunroof motor assembly connector and
ground.
OK or NG
OK
>> Replace sunroof motor assembly.
NG
>> Check the condition of the harness and the connector.
Sunroof Switch Circuit Check 4
AIS002KC
1.
CHECK SUNROOF SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect sunroof switch connector.
3.
Check continuity between sunroof switch terminals 1 and 6.
OK or NG
OK
>> GO TO 2.
NG
>> Replace sunroof switch.
2.
CHECK SUNROOF SWITCH OUTPUT SINGAL
1.
Connect sunroof switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between sunroof motor assembly connector and
ground.
OK or NG
OK
>> Replace sunroof motor assembly.
NG
>> Check the condition of the harness and the connector.
Connector
Terminals (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
R6
2 (G)
3 (R)
Ground
Slide switch
SLIDE POSITION 2
0
Other than above
Battery voltage
PIIA4515E
Terminals
Condition
Continuity
1
6
Slide switch
SLIDE POSITION 3
Yes
Other than above
No
PIIA4520E
Connector
Terminals (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
R6
2 (G)
Ground
Slide switch
SLIDE POSITION 3
0
Other than above
Battery voltage
PIIA4518E
SUNROOF
RF-27
C
D
E
F
G
H
J
K
L
M
A
B
RF
Revision: 2004 November
2004 Murano
Sunroof Switch Circuit Check 5
AIS002KD
1.
CHECK SUNROOF SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect sunroof switch connector.
3.
Check continuity between sunroof switch terminals 1, 3 and 6.
OK or NG
OK
>> GO TO 2.
NG
>> Replace sunroof switch.
2.
CHECK SUNROOF SWITCH OUTPUT SINGAL
1.
Connect sunroof switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between sunroof motor assembly connector and
ground.
OK or NG
OK
>> Replace sunroof motor assembly.
NG
>> Check the condition of the harness and the connector.
Sunroof Switch Circuit Check 6
AIS002KE
1.
CHECK SUNROOF SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect sunroof switch connector.
3.
Check continuity between sunroof switch terminals 3 and 6.
OK or NG
OK
>> GO TO 2.
NG
>> Replace sunroof switch.
Terminals
Condition
Continuity
1
3
6
Slide switch
FULL CLOSE position
Yes
Other than above
No
PIIA4523E
Connector
Terminals (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
R6
2 (G)
4 (Y)
Ground
Slide switch
SLIDE POSITION 4
0
Other than above
Battery voltage
PIIA4521E
Terminals
Condition
Continuity
3
6
Slide switch
FULL OPEN position
Yes
Other than above
No
PIIA4526E
RF-28
SUNROOF
Revision: 2004 November
2004 Murano
2.
CHECK SUNROOF SWITCH OUTPUT SINGAL
1.
Connect sunroof switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between sunroof motor assembly connector and
ground.
OK or NG
OK
>> Replace sunroof motor assembly.
NG
>> Check the condition of the harness and the connector.
Sunroof Switch Circuit Check 7
AIS002KF
1.
CHECK SUNROOF SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect sunroof switch connector.
3.
Check continuity between sunroof switch terminals 5 and 6.
OK or NG
OK
>> GO TO 2.
NG
>> Replace sunroof switch.
2.
CHECK SUNROOF SWITCH OUTPUT SINGAL
1.
Connect sunroof switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between sunroof motor assembly connector and
ground.
OK or NG
OK
>> Replace sunroof motor assembly.
NG
>> Check the condition of the harness and the connector.
Connector
Terminals (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
R6
4 (Y)
Ground
Slide switch
FULL OPEN position
0
Other than above
Battery voltage
PIIB0505E
Terminals
Condition
Continuity
5
6
Tilt switch
UP position
Yes
Other than above
No
PIIA4529E
Connector
Terminals (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
R6
1 (V)
Ground
Tilt switch
UP position
0
Other than above
Battery voltage
PIIA4527E
SUNROOF
RF-29
C
D
E
F
G
H
J
K
L
M
A
B
RF
Revision: 2004 November
2004 Murano
Sunroof Switch Circuit Check 8
AIS002KG
1.
CHECK SUNROOF SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect sunroof switch connector.
3.
Check continuity between sunroof switch terminals 4 and 6.
OK or NG
OK
>> GO TO 2.
NG
>> Replace sunroof switch.
2.
CHECK SUNROOF SWITCH OUTPUT SINGAL
1.
Connect sunroof switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between sunroof motor assembly connector and
ground.
OK or NG
OK
>> Replace sunroof motor assembly.
NG
>> Check the condition of the harness and the connector.
Sunroof Switch Circuit Check 9
AIS002KH
1.
CHECK SUNROOF MOTOR OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect sunroof motor switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between sunroof motor assembly connector R6
terminals 1, 2, 3, 4, 5 and ground.
OK or NG
OK
>> GO TO 2
NG
>> Replace sunroof motor assembly.
Terminals
Condition
Continuity
4
6
Tilt switch
UP position
Yes
Other than above
No
PIIA4532E
Connector
Terminals (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
R6
5 (O)
Ground
Tilt switch
DOWN position
0
Other than above
Battery voltage
PIIA4530E
1 (V) – Ground
: Battery voltage
2 (G) – Ground
: Battery voltage
3 (R) – Ground
: Battery voltage
4 (Y) – Ground
: Battery voltage
5 (O) – Ground
: Battery voltage
PIIA4536E
RF-30
SUNROOF
Revision: 2004 November
2004 Murano
2.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect sunroof switch connector.
3.
Check continuity between sunroof motor assembly connector
R6 terminals 1, 2, 3, 4, 5 and sunroof switch connector R5 termi-
nals 1, 2, 3, 4, 5.
4.
Check continuity between sunroof motor assembly connector
R6 terminals 1, 2, 3, 4, 5 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
Check continuity between sunroof switch connector R5 terminal 6
and ground.
OK or NG
OK
>> Check condition of the harness and the connector.
NG
>> Repair or replace harness.
1 (V) – 5 (V)
: Continuity should exist.
2 (G) – 1 (G)
: Continuity should exist.
3 (R) – 2 (R)
: Continuity should exist.
4 (Y) – 3 (Y)
: Continuity should exist.
5 (O) – 4 (O)
: Continuity should exist.
1 (V) – Ground
: Continuity should not exist.
2 (G) – Ground
: Continuity should not exist.
3 (R) – Ground
: Continuity should not exist.
4 (Y) – Ground
: Continuity should not exist.
5 (O) – Ground
: Continuity should not exist.
PIIA4537E
6 (B) – Ground
: Continuity should exist.
PIIA4538E
SUNROOF
RF-31
C
D
E
F
G
H
J
K
L
M
A
B
RF
Revision: 2004 November
2004 Murano
Sunroof Switch Circuit Check 10
AIS00351
1.
CHECK SUNROOF SWITCH OUTPUT SINGAL
1.
Turn ignition switch ON.
2.
Check voltage between sunroof motor assembly connector and
ground.
OK or NG
OK
>> Replace sunroof motor assembly.
NG
>> GO TO 2.
2.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect sunroof motor assembly and sunroof switch connector.
3.
Check continuity between sunroof motor assembly connector R6 terminal 2 and sunroof switch connector
R5 terminal 1.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between sunroof motor
assembly and sunroof switch.
3.
CHECK SUNROOF SWITCH
Check continuity between sunroof switch terminals 1 and 6.
OK or NG
OK
>> Check the condition of the harness and the connector.
NG
>> Replace sunroof switch.
Connector
Terminals (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
R6
2 (G)
Ground
Slide switch
SLIDE POSITION 2
SLIDE POSITION 3
SLIDE POSITION 4
0
Other than above
Battery voltage
PIIA4518E
2 (G) – 1 (G)
: Continuity should exist.
PIIA4519E
Terminals
Condition
Continuity
1
6
Slide switch
SLIDE POSITION 2
SLIDE POSITION 3
SLIDE POSITION 4
Yes
Other than above
No
PIIA4520E
RF-32
SUNROOF
Revision: 2004 November
2004 Murano
Sunroof Switch Circuit Check 11
AIS00352
1.
CHECK SUNROOF SWITCH OUTPUT SINGAL
1.
Turn ignition switch ON.
2.
Check voltage between sunroof motor assembly connector and
ground.
OK or NG
OK
>> Replace sunroof motor assembly.
NG
>> GO TO 2.
2.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect sunroof motor assembly and sunroof switch connector.
3.
Check continuity between sunroof motor assembly connector R6 terminal 3 and sunroof switch connector
R5 terminal 2.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between sunroof motor
assembly and sunroof switch.
3.
CHECK SUNROOF SWITCH
Check continuity between sunroof switch terminals 2 and 6.
OK or NG
OK
>> Check the condition of the harness and the connector.
NG
>> Replace sunroof switch.
Connector
Terminals (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
R6
3 (R)
Ground
Slide switch
FULL CLOSE
SLIDE POSITION 1
SLIDE POSITION 2
0
Other than above
Battery voltage
PIIA4512E
3 (R) – 2 (R)
: Continuity should exist.
PIIA4513E
Terminals
Condition
Continuity
2
6
Slide switch
FULL CLOSE
SLIDE POSITION 1
SLIDE POSITION 2
Yes
Other than above
No
PIIA4514E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст