Nissan Murano Z50 (2004 year). Manual — part 199
SUNROOF
RF-33
C
D
E
F
G
H
J
K
L
M
A
B
RF
Revision: 2004 November
2004 Murano
Sunroof Switch Circuit Check 12
AIS00353
1.
CHECK SUNROOF SWITCH OUTPUT SINGAL
1.
Turn ignition switch ON.
2.
Check voltage between sunroof motor assembly connector and
ground.
OK or NG
OK
>> Replace sunroof motor assembly.
NG
>> GO TO 2.
2.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect sunroof motor assembly and sunroof switch connector.
3.
Check continuity between sunroof motor assembly connector R6 terminal 4 and sunroof switch connector
R5 terminal 3.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between sunroof motor
assembly and sunroof switch.
3.
CHECK SUNROOF SWITCH
Check continuity between sunroof switch terminals 3 and 6.
OK or NG
OK
>> Check the condition of the harness and the connector.
NG
>> Replace sunroof switch.
Connector
Terminals (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
R6
4 (Y)
Ground
Slide switch
FULL CLOSE
FULL OPEN
SLIDE POSITION 4
0
Other than above
Battery voltage
PIIB0505E
4 (Y) – 3 (Y)
: Continuity should exist.
PIIA4525E
Terminals
Condition
Continuity
3
6
Slide switch
FULL CLOSE
FULL OPEN
SLIDE POSITION 4
Yes
Other than above
No
PIIA4526E
RF-34
SUNROOF
Revision: 2004 November
2004 Murano
Door Switch Check
AIS002KI
1.
CHECK DOOR SWITCH INPUT SIGNAL
With CONSULT-II
Check door switches (“DOOR SW-DR” and “DOOR SW-AS”) in “DATA MONITOR” mode with CONSULT-II.
Without CONSULT-II
Check voltage between BCM connector and ground.
OK or NG
OK
>> Door switch is OK.
NG
>> GO TO 2.
Monitor item
Condition
DOOR SW-DR
OPEN
: ON
CLOSE
: OFF
DOOR SW-AS
OPEN
: ON
CLOSE
: OFF
PIIA2464E
Item
Con-
nector
Terminals (Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(- )
Passenger
side
M34
12 (SB)
Ground
OPEN
0
CLOSE
Battery voltage
Driver
side
M36
62 (R)
OPEN
0
CLOSE
Battery voltage
PIIA6158E
SUNROOF
RF-35
C
D
E
F
G
H
J
K
L
M
A
B
RF
Revision: 2004 November
2004 Murano
2.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect BCM and front door lock assembly (driver side and passenger side) connector.
3.
Check continuity between BCM connector M34, 36 terminals 12, 62 and front door lock assembly connec-
tor D10 (driver side), D38 (passenger side) terminal 4.
4.
Check continuity between BCM connector M34, 36 terminals 12,
62 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between BCM and front door
lock assembly.
3.
CHECK DOOR SWITCH
Check continuity between front door lock assembly terminal 4 and 5.
OK or NG
OK
>> GO TO 4.
NG
>> Replace malfunction front door lock assembly.
Driver side
62 (SB) – 4 (SB)
: Continuity should exist.
Passenger side
12 (R/G) – 4 (R/G)
: Continuity should exist.
12 (R/G) – Ground
: Continuity should not exist.
62 (SB) – Ground
: Continuity should not exist.
PIIB0907E
Terminal
Door switch
Continuity
4
5
OPEN
No
CLOSE
Yes
PIIA4220E
RF-36
SUNROOF
Revision: 2004 November
2004 Murano
4.
CHECK DOOR SWITCH GROUND CIRCUIT
1.
Check continuity between front door lock assembly connector D10 (driver side), D38 (passenger side) ter-
minal 5 and ground.
OK or NG
OK
>> Check the condition of the harness and the connector.
NG
>> Repair or replace harness between front door lock
assembly and ground.
5 (B) - Ground
: Continuity should exist.
PIIA9680E
SUNROOF
RF-37
C
D
E
F
G
H
J
K
L
M
A
B
RF
Revision: 2004 November
2004 Murano
Wind Deflector Inspection
AIS002EI
Check that the wind deflector is properly raised by manual. If a mal-
function is detected, remove and visually check it. If it is damaged,
replace it with a new one. If no damage is found, reinstall it properly.
Link and Wire Assembly
AIS002EJ
NOTE:
Before replacing a suspect part, carefully ensure it is the source of noise being experienced.
1.
Check link to determine if coated film has peeled off to such an extent that substrate is visible. Check also
to determine if link is the source of noise. If it is, replace it.
2.
Visually check to determine if a sufficient amount of grease has been applied to wire or rail groove. If not,
add grease as required.
3.
Check wire for any damage or deterioration. If any damage is found, replace wire.
Fitting Adjustment
AIS002EK
PIIA5061E
PIIA4248E
RF-38
SUNROOF
Revision: 2004 November
2004 Murano
LID WEATHERSTRIP OVERLAP ADJUSTMENT AND SURFACE MISMATCH ADJUSTMENT
1.
Tilt up glass lid.
2.
After loosening glass lid TORX bolts (T25) (left and right), tilt
down glass lid.
3.
Adjust glass lid from outside of vehicle so it resembles “A–A” “B–
B” “C–C” as shown in the figure.
4.
To prevent glass lid from moving after adjustment, first tighten
the TORX bolts (T25) of front left, and then tighten the TORX
bolts (T25) of rear right.
5.
Tighten remaining TORX bolts (T25), being careful to prevent
glass lid from moving.
6.
Tilt glass lid up and down several times to check that it moves
smoothly.
Removal and Installation
AIS002EL
●
After any adjustment, check sunroof operation and glass lid alignment.
●
Handle finisher plate and glass lid with care so not to cause damage.
●
It is desirable for easy installation to mark each point before removal.
CAUTION:
●
Always work with a helper.
●
Fully close the glass lid assembly, before removal, then do not operate sunroof motor assembly
after removal.
PIIA3501E
SUNROOF
RF-39
C
D
E
F
G
H
J
K
L
M
A
B
RF
Revision: 2004 November
2004 Murano
PIIB0906E
RF-40
SUNROOF
Revision: 2004 November
2004 Murano
SUNROOF UNIT ASSEMBLY
Removal
CAUTION:
●
Always work with a helper.
●
When taking sunroof unit out, use shop clothes to protect the seats and trim from damage.
●
After installing the sunroof unit and glass lid, be sure to perform the leakage test and make sure
there is no malfunction.
1.
Tilt glass lid up.
2.
Remove the headlining. Refer to
EI-36, "Removal and Installation"
3.
Disconnect drain hoses.
4.
Remove glass lid. Refer to
5.
Remove motor mounting screws. Remove sunroof motor
assembly and disconnect harness connector.
CAUTION:
●
Before removing sunroof motor assembly, make sure
that sunroof is fully closed.
●
After removing sunroof motor assembly, do not attempt
to rotate sunroof motor as a single unit.
6.
Remove nuts from the front end and side rail.
7.
Remove sunroof bracket bolts, then remove sunroof unit assem-
bly from roof panel.
8.
Remove sunroof unit assembly through the passenger compartment while being careful not to damage
the seats and trim.
1.
Glass lid
2.
TORX bolt
3.
Washer
4.
Rear sunroof bracket
5.
Front sunroof bracket
6.
Wind defrector
7.
Sunroof unit assembly
8.
Noise cover
9.
Sunroof motor assembly
10. Screw
11.
Sunshade
12. Nut
13. Drain plate
14. Sunshade stopper
PIIA4793E
PIIA5060E
PIIA4241E
SUNROOF
RF-41
C
D
E
F
G
H
J
K
L
M
A
B
RF
Revision: 2004 November
2004 Murano
Installation
1.
Temporarily tighten the mounting bolts on the sunroof brackets
(RH/LH).
2.
Bring sunroof unit assembly into passenger compartment and
then place the rear end of the rail onto the sunroof brackets.
3.
Tighten the mounting nuts on the front end.
4.
Tighten the installation points diagonally excluding the installation point of the sunroof bracket around the
roof opening.
5.
Tighten the rear sunroof bracket bolts of the vehicle side, and
then tighten the bolt of the rail side.
GLASS LID
Removal
1.
Tilt up glass lid.
2.
Remove TORX bolts (T25), then remove glass lid.
Installation
1.
Tighten bolts diagonally on the glass lid.
2.
After installation, carry out fitting adjustment.
PIIA4241E
PIIA5060E
PIIA4241E
PIIA3508E
RF-42
SUNROOF
Revision: 2004 November
2004 Murano
SUNSHADE
Removal
NOTE:
Detaching is possible is even by the on vehicle.
1.
Remove the headlining. Refer to
EI-36, "Removal and Installation"
2.
Remove sunshade stopper.
3.
Pull sunshade out of the rear end of the sunroof frame, and
remove it from the frame.
CAUTION:
Thing working to damage neither sunshade and sunshade
knob while lifting up a little.
Installation
Install in the reverse order of removal.
WIND DEFLECTOR
Removal
NOTE:
Detaching is possible is even by the on vehicle.
1.
Open the sunroof lid.
2.
Remove spring hinge screws, then remove hinge from the
frame.
3.
Remove stopper from the sunroof unit assembly.
4.
Turn the wind deflector and then remove it from ditch of the sun-
roof unit assembly.
Installation
Install in the reverse order of removal.
SUNROOF MOTOR ASSEMBLY
Removal
1.
Remove headlining. Refer to
EI-36, "Removal and Installation"
2.
Remove sunroof motor mounting screws.
3.
Disconnect harness connector from sunroof motor assembly,
then remove sunroof motor assembly.
CAUTION:
●
When removing the sunroof motor assembly, be sure that
the sunroof lid is in the fully closed position.
●
Do not run the removed sunroof motor assembly as a
single unit.
Installation
1.
Move the sunroof motor assembly laterally little by little so that the gear is completely engaged into the
wire on the sunroof unit assembly and the mounting surface becomes parallel. Then secure the sunroof
motor assembly with screws.
PIIA5064E
PIIA3510E
PIIA4793E
SUNROOF
RF-43
C
D
E
F
G
H
J
K
L
M
A
B
RF
Revision: 2004 November
2004 Murano
CAUTION:
●
Before installing the sunroof motor assembly, be sure to place the link and wire assembly in the
symmetrical and fully closed position.
●
Align the link notch with the hole of the culisse (fully closed : RH and LH).
2.
Confirm the body ground of the noise cover is connected.
3.
Initialization it after installing the sunroof motor. Refer to
RF-12, "INITIALIZATION PROCEDURE"
.
PIIA5062E
PIIA5063E
RF-44
SUNROOF
Revision: 2004 November
2004 Murano
RFD-1
REAR FINAL DRIVE
D DRIVELINE/AXLE
CONTENTS
C
E
F
G
H
I
J
K
L
M
SECTION
RFD
A
B
RFD
Revision: 2004 November
2004 Murano
REAR FINAL DRIVE
PRECAUTIONS . . . . . . . . . . . . . . .. 2
Precautions . . . . . . . . . . . . . . . .. 2
PREPARATION . . . . . . . . . . . . . . ... 3
Special Service Tools . . . . . . . . . . . ... 3
Commercial Service Tools . . . . . . . . . . 6
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 7
NVH Troubleshooting Chart . . . . . . . . . . 7
FRONT OIL SEAL . . . . . . . . . . . . . .. 8
Removal and Installation . . . . . . . . . . .. 8
REMOVAL . . . . . . . . . . . . . . . . 8
INSTALLATION . . . . . . . . . . . . . . 9
SIDE OIL SEAL . . . . . . . . . . . . . . 10
Removal and Installation . . . . . . . . . . 10
REMOVAL . . . . . . . . . . . . . . ... 10
INSTALLATION . . . . . . . . . . . . ... 10
REAR FINAL DRIVE ASSEMBLY . . . . . . . .11
Removal and Installation . . . . . . . . . . .11
REMOVAL . . . . . . . . . . . . . . . 11
INSTALLATION . . . . . . . . . . . . ... 12
Components . . . . . . . . . . . . . . ... 13
Pre-Inspection . . . . . . . . . . . . . . 14
Disassembly and Assembly . . . . . . . . . 19
DISASSEMBLY . . . . . . . . . . . . ... 19
ASSEMBLY . . . . . . . . . . . . . . . 22
SERVICE DATA AND SPECIFICATIONS (SDS) . .. 29
AVAILABLE SIDE GEAR THRUST WASHERS ... 29
Drive Pinion Adjustment . . . . . . . . . . . 29
AVAILABLE DRIVE PINION ADJUSTING SHIM ... 29
Side Bearing Preload Adjustment . . . . . . ... 29
RFD-2
PRECAUTIONS
Revision: 2004 November
2004 Murano
PRECAUTIONS
PFP:00001
Precautions
ADS000W5
CAUTION:
●
Check for the correct installation status prior removal or disassembly. When mating marks are
required, be sure they do not interfere with the function of the parts they are applied to.
●
Carry out an overhaul in a clean work place, Using a dust proof room is recommended.
●
Before disassembly, using steam or white gasoline, completely remove sand and mud from the
exterior the unit, preventing them from entering into the unit during disassembly or assembly.
●
Check appearance of the disassembled parts for damage, deformation, and abnormal wear. If a
malfunction is detected, replace it with a new one.
●
Normally replace lock pins, oil seals, and bearings with new ones every times they are removed.
●
In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to out-
side. If tightening sequence is specified, observe it.
●
Clean and flush the parts sufficiently and blow them dry.
●
Be careful not to damage the sliding surfaces and mating surface.
●
When applying sealant, remove the old sealant from the mounting surface; then remove any mois-
ture, oil, and foreign materials from the application and mounting surfaces.
●
Always use shop paper for cleaning the inside of components.
●
Avoid using cotton gloves or a shop cloth to prevent entering of lint.
●
During assembly, observe the specified tightening torque, and new differential oil, Vaseline, or
multi-purpose grease, as specified for each vehicle, when necessary.
PREPARATION
RFD-3
C
E
F
G
H
I
J
K
L
M
A
B
RFD
Revision: 2004 November
2004 Murano
PREPARATION
PFP:00002
Special Service Tools
ADS000EE
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number (Kent-Moore No.)
Tool name
Description
KV38108300 (
–
)
Drive pinion flange wrench
Removing and installing companion
flange lock nut
ST27861000 (
–
)
Drift
a: 62 mm (2.44 in) dia.
b: 52 mm (2.05 in) dia.
●
Installing final drive front oil seal
●
Installing final drive side oil seal
ST33290001 (J34286)
Side bearing outer race puller
Removing front oil seal
KV38100200 (J26233)
Drift
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.
●
Installing final drive front oil seal
●
Installing final drive side oil seal
ST3127S000 (J25765-A)
Preload gauge
Measuring preload torque
ST33052000 (
–
)
Drift
a: 22 mm (0.87 in) dia.
b: 28 mm (1.10 in) dia.
Removing side bearing inner race
PDIA0045E
ZZA0832D
ZZA0601D
ZZA1143D
ZZA0503D
ZZA1023D
RFD-4
PREPARATION
Revision: 2004 November
2004 Murano
KV40100610 (J26089)
Drift
a: 63 mm (2.48 in) dia.
b: 54.3 mm (2.138 in) dia.
●
Removing and installing gear carrier
and rear cover (2 pieces are used)
●
Installing pinion front bearing inner
race
ST23550000 (
–
)
Tip diameter: 4.5 mm (0.177 in) dia.
Pin punch
Removing and installing lock pin
ST17130000 (
–
)
Drift
a: 31.8 mm (1.252 in) dia.
b: 58 mm (2.28 in) dia.
Installing pinion rear bearing outer
race
ST33230000 (J25805-01)
Drift
a: 51 mm (2.01 in) dia.
b: 41 mm (1.61 in) dia.
c: 28.5 mm (1.122 in) dia.
Installing pinion front bearing outer
race
ST23860000 (
–
)
Drift
a: 38 mm (1.50 in) dia.
b: 33 mm (1.30 in) dia.
●
Installing pinion rear bearing inner
race
●
Installing pinion front bearing inner
race
ST38220000 (
–
)
Press stand
a: 63 mm (2.48 in) dia.
b: 65 mm (2.56 in)
Installing pinion front bearing inner
race
KV40105020 (
–
)
Drift
a: 39.7 mm (1.563 in) dia.
b: 35 mm (1.38 in) dia.
c: 15 mm (0.59 in)
Installing side bearing inner race
Tool number (Kent-Moore No.)
Tool name
Description
ZZA0810D
ZZA0815D
ZZA0836D
ZZA1046D
ZZA0534D
ZZA1058D
ZZA1133D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст