Qashqai J11. Exterior Lighting system — part 11
FRONT COMBINATION LAMP
EXL-161
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Removal and Installation
INFOID:0000000010338851
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-8, "Precautions for Removing Battery Terminal"
.
REMOVAL
1.
Remove front bumper fascia. Refer to
EXT-19, "Removal and Installation"
.
2.
Remove front combination lamp assembly mounting bolts.
3.
Pull out front combination lamp assembly forward the vehicle.
4.
Disconnect front combination lamp assembly harness connectors.
5.
Remove front combination lamp assembly.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, perform aiming adjustment. Refer to the following:
• LHD MODELS: Refer to
.
Front turn signal lamp bulb
Front turn signal lamp bulb socket
Front combination lamp bracket
Front combination lamp housing
JMLIA5092ZZ
EXL-162
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
FRONT COMBINATION LAMP
• RHD MODELS: Refer to
Replacement
INFOID:0000000010431361
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-8, "Precautions for Removing Battery Terminal"
.
• After installing the bulb, install the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned OFF.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB (HI)
CAUTION:
Replacement of a single part is not possible due to the adoption of LED bulb. for replacement, replace
front combination lamp as a set.
HEADLAMP BULB (LO)
CAUTION:
Replacement of a single part is not possible due to the adoption of LED bulb. for replacement, replace
front combination lamp as a set.
DAYTIME RUNNING LIGHT/ PARKING LAMP BULB
CAUTION:
Replacement of a single part is not possible due to the adoption of LED bulb. for replacement, replace
front combination lamp as a set.
FRONT TURN SIGNAL LAMP BULB
LH side
1.
Remove air duct. Refer to the following.
• HRA2DDT: Refer to
EM-23, "Removal and Installation"
EM-147, "Removal and Installation"
• K9K: Refer to
EM-279, "Removal and Installation"
• R9M: Refer to
EM-380, "Removal and Installation"
.
2.
Rotate front turn signal lamp bulb socket counterclockwise and unlock it.
3.
Remove front turn signal lamp bulb socket from front combination lamp housing.
4.
Remove front turn signal lamp bulb from turn signal lamp bulb socket.
RH side
1.
Rotate front turn signal lamp bulb socket counterclockwise and unlock it.
2.
Remove front turn signal lamp bulb socket from front combination lamp housing.
3.
Remove front turn signal lamp bulb from turn signal lamp bulb socket.
Disassembly and Assembly
INFOID:0000000010338853
DISASSEMBLY
1.
Remove front combination lamp bracket mounting screws, and then remove front combination lamp
bracket from front combination lamp housing.
2.
Disconnect front combination lamp harness connectors.
3.
Rotate front turn signal lamp bulb socket counterclockwise and unlock it.
4.
Remove front turn signal lamp bulb socket from front combination lamp housing.
5.
Remove front turn signal lamp bulb from front turn signal lamp bulb socket.
ASSEMBLY
Note the following item, and then install in the reverse order of removal.
CAUTION:
• After installing the bulb, install the bulb socket securely watertightness.
• After installation, perform aiming adjustment. Refer to following.
- LHD models: Refer to
FRONT COMBINATION LAMP
EXL-163
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
- RHD models: Refer to
EXL-156, "RHD : Aiming Adjustment Procedure"
.
EXL-164
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
FRONT FOG LAMP
FRONT FOG LAMP
Exploded View
INFOID:0000000010338858
Removal and Installation
INFOID:0000000010338859
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-8, "Precautions for Removing Battery Terminal"
.
REMOVAL
1.
Remove front fender protector to make work space. Refer to
EXT-32, "Removal and Installation"
.
2.
Disconnect front fog lamp harness connector.
3.
Remove front fog lamp fixing bolt, and then remove front fog lamp.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
EXL-158, "Aiming Adjustment Procedure"
Replacement
INFOID:0000000010338860
CAUTION:
Front bumper fascia
Front bumper finisher
Front fog lamp
Front fog lamp bulb
: N·m (kg-m, in-lb)
JMLIA5093GB
FRONT FOG LAMP
EXL-165
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-8, "Precautions for Removing Battery Terminal"
.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned OFF.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT FOG LAMP BULB
1.
Remove fender protector to make work space. Refer to
EXT-32, "Removal and Installation"
.
2.
Disconnect front fog lamp harness connector
.
3.
Rotate front fog lamp bulb
counterclockwise and unlock it.
JPLIA0345ZZ
EXL-166
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
SIDE TURN SIGNAL LAMP
SIDE TURN SIGNAL LAMP
Exploded View
INFOID:0000000010338861
.
Removal and Installation
INFOID:0000000010338862
REMOVAL
1.
Remove door mirror cover. Refer to
MIR-31, "Removal and Installation"
.
2.
Remove side turn signal lamp fixing screws.
3.
Remove seal packing
and disconnect side turn signal lamp
harness connector
, and then remove side turn signal lamp
from door mirror housing.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000010338863
CAUTION:
Replacement of a single part is not possible due to the adoption of LED bulb. For replacement, replace
side turn signal lamp as a set.
SIDE TURN SIGNAL LAMP
1.
Remove side turn signal lamp. Refer to
MIR-31, "Removal and Installation"
2.
Replace side turn signal lamp with new part.
JMLIA4978ZZ
LIGHTING & TURN SIGNAL SWITCH
EXL-167
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LIGHTING & TURN SIGNAL SWITCH
Removal and Installation
INFOID:0000000010338866
REMOVAL
Remove light & turn signal switch (combination switch). Refer to
BCS-133, "Removal and Installation"
.
INSTALLATION
Install in the reverse order of removal.
EXL-168
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
HAZARD SWITCH
HAZARD SWITCH
Exploded View
INFOID:0000000010427649
Removal and Installation
INFOID:0000000010427650
REMOVAL
1.
Remove center ventilator grille. Refer to
IP-13, "Removal and Installation"
.
2.
Disengage fixing pawls, and then remove hazard switch from center ventilator grille.
INSTALLATION
Install in the reverse order of removal.
Center ventilator grille
Hazard switch
: Pawl
JMLIA5094ZZ
HEIGHT SENSOR
EXL-169
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HEIGHT SENSOR
Exploded View
INFOID:0000000010338873
2WD
4WD
Height sensor
: Vehicle front
: N·m (kg-m, in-lb)
JMLIA5096GB
EXL-170
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
HEIGHT SENSOR
Removal and Installation
INFOID:0000000010338874
REMOVAL
1.
Disconnect height sensor harness connector.
2.
Remove height sensor assembly mounting bolts.
3.
Remove height sensor assembly.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Be sure to perform
″
SENSOR INITIALIZE
″
when removing the height sensor. Refer to
Height sensor
: Vehicle front
: N·m (kg-m, in-lb)
JMLIA5097GB
LIGHT & RAIN SENSOR
EXL-171
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LIGHT & RAIN SENSOR
Exploded View
INFOID:0000000010431500
Removal and Installation
INFOID:0000000010431501
REMOVAL
Remove light & rain sensor. Refer to
WW-92, "Removal and Installation"
.
INSTALLATION
Install in the reverse order of removal.
EXL-172
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
REAR COMBINATION LAMP
REAR COMBINATION LAMP
Exploded View
INFOID:0000000010338875
REMOVAL
Body Side
Back Door Side
Grommet A
Grommet B
Rear combination lamp
: Clip
: Clip
: N·m (kg-m, in-lb)
JMLIA5098GB
REAR COMBINATION LAMP
EXL-173
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DISASSEMBLY
Back door panel
Rear combination lamp
Grommet
: N·m (kg-m, in-lb)
JMLIA5099GB
EXL-174
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
REAR COMBINATION LAMP
Removal and Installation
INFOID:0000000010338876
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-8, "Precautions for Removing Battery Terminal"
.
• When removing, always use a remover tool that is made of plastic.
REMOVAL
Rear Combination Lamp (body side)
1.
Fully open trunk lid.
2.
Remove rear combination lamp mounting bolts
.
Rear combination lamp housing
(back door side)
Seal packing
Rear fog lamp bulb
(driver side only)
Rear fog lamp bulb socket
(driver side only)
Back-up lamp bulb
Back-up lamp bulb socket
Rear turn signal lamp bulb socket
Rear turn signal lamp bulb
Rear combination lamp housing
(body side)
: Vehicle front
: Always replace after every disassembly
JMLIA5407ZZ
JMLIA5137ZZ
REAR COMBINATION LAMP
EXL-175
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
3.
Pull rear combination lamp toward vehicle rear to disengage fix-
ing clips.
4.
Disconnect rear combination lamp harness connectors, and then remove rear combination lamp from
body panel.
Rear Combination Lamp (back door side)
1.
Remove back door inner finisher. Refer to
INT-31, "Removal and Installation"
2.
Remove back door finisher. Refer to
EXT-45, "Removal and Installation"
3.
Remove rear combination lamp mounting nuts
and discon-
nect rear combination lamp harness connectors.
4.
Pull rear combination lamp toward vehicle rear to remove rear combination lamp from back door.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Always replace seal packing with new part after every removal.
Replacement
INFOID:0000000010338877
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-8, "Precautions for Removing Battery Terminal"
.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned OFF.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
REAR TURN SIGNAL LAMP BULB
1.
Remove rear combination lamp (body side). Refer to
EXL-174, "Removal and Installation"
2.
Rotate rear turn signal lamp bulb socket counterclockwise, and then remove rear turn signal lamp bulb
socket.
3.
Remove rear turn signal lamp bulb from rear turn signal lamp bulb socket.
STOP/TAIL LAMP
CAUTION:
Replacement of a single part is not possible due to the adoption of LED bulb. For replacement, replace
rear combination lamp assembly as a set.
REAR FOG LAMP (DRIVER SIDE ONLY)
1.
Remove rear combination lamp (back door side). Refer to
EXL-174, "Removal and Installation"
2.
Rotate rear fog lamp bulb socket counterclockwise, and then remove rear fog lamp bulb socket.
: Clip
JMLIA5138ZZ
JMLIA5139ZZ
EXL-176
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
REAR COMBINATION LAMP
3.
Remove rear fog lamp bulb from rear fog lamp bulb socket.
BACK-UP LAMP
1.
Remove rear combination lamp (back door side). Refer to
EXL-174, "Removal and Installation"
2.
Rotate back-up lamp bulb socket counterclockwise, and then remove back-up lamp bulb socket.
3.
Remove back-up lamp bulb from back-up lamp bulb socket.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст