Qashqai J11. Exterior Lighting system — part 20
EXL-306
< SYMPTOM DIAGNOSIS >
[HALOGEN HEADLAMP]
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
Description
INFOID:0000000010470002
Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.
Diagnosis Procedure
INFOID:0000000010470003
1.
COMBINATION SWITCH INSPECTION
Check combination switch. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HIGH BEAM REQUEST SIGNAL
With CONSULT
1.
Select “HIGH BEAM REQ” in “Data Monitor” mode of “IPDM E/R” using CONSULT.
2.
With operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-67, "Removal and Installation"
NO
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
Monitor item
Condition
Monitor status
HIGH BEAM REQ
Lighting switch
(2ND)
HI or PASS
On
LO
Off
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
EXL-307
< SYMPTOM DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
Description
INFOID:0000000010470004
Both side headlamps (LO) are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000010470005
1.
CHECK COMBINATION SWITCH
Check combination switch. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK LOW BEAM REQUEST SIGNAL
With CONSULT
1.
Select “LOW BEAM REQ” in “Data Monitor” mode of “IPDM E/R” using CONSULT.
2.
With operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-67, "Removal and Installation"
.
NO
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
Monitor item
Condition
Monitor status
LOW BEAM REQ
Lighting switch
2ND
On
OFF
Off
EXL-308
< SYMPTOM DIAGNOSIS >
[HALOGEN HEADLAMP]
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
Description
INFOID:0000000010470006
The parking, license plate and tail lamps are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000010470007
1.
COMBINATION SWITCH INSPECTION
Check combination switch. Refer to
.
Is the combination switch normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK POSITION LIGHT REQUEST SIGNAL
With CONSULT
1.
Select “POSITION LIGHT REQ” in “Data Monitor” mode of “IPDM E/R” using CONSULT.
2.
With operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-67, "Removal and Installation"
NO
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
Monitor item
Condition
Monitor status
POSITION LIGHT REQ
Lighting switch
1ST
On
OFF
Off
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
EXL-309
< SYMPTOM DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
Description
INFOID:0000000010470008
Both side front fog lamps are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000010470009
1.
COMBINATION SWITCH INSPECTION
Check combination switch. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK FRONT FOG LIGHT REQUEST SIGNAL
With CONSULT
1.
Select “FRONT FOG LAMP REQ” in “Data Monitor” mode of “IPDM E/R” using CONSULT.
2.
With operating the front fog lamp switch, check the monitor status.
Is the item status normal?
YES
>> Replace IPDM E/R. Refer to
PCS-67, "Removal and Installation"
.
NO
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
Monitor item
Condition
Monitor status
FRONT FOG LAMP REQ
Front fog lamp switch
(With lighting switch 1ST)
ON
On
OFF
Off
EXL-310
< PERIODIC MAINTENANCE >
[HALOGEN HEADLAMP]
HEADLAMP AIMING ADJUSTMENT
PERIODIC MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
LHD
LHD : Description
INFOID:0000000010500187
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Never remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.).
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
JMLIA5134ZZ
Headlamp LH (UP/DOWN)
adjustment screw
Headlamp LH (INSIDE/OUTSIDE)
adjustment screw
Headlamp RH (INSIDE/OUTSIDE)
adjustment screw
Headlamp RH (UP/DOWN)
adjustment screw
: Vehicle front
Adjustment screw
Screwdriver rotation
Facing direction
Headlamp LH (UP/DOWN)
Clockwise
UP
Counterclockwise
DOWN
Headlamp LH (INSIDE/OUTSIDE)
Clockwise
INSIDE
Counterclockwise
OUTSIDE
Headlamp RH (INSIDE/OUTSIDE)
Clockwise
INSIDE
Counterclockwise
OUTSIDE
HEADLAMP AIMING ADJUSTMENT
EXL-311
< PERIODIC MAINTENANCE >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LHD : Aiming Adjustment Procedure
INFOID:0000000010339002
1.
Place the screen.
NOTE:
• Stop the vehicle at the perpendicular angle to the wall.
• Set the screen so that it is perpendicular to a level load surface.
2.
Face the vehicle squarely toward the screen and make the distance between the headlamp center and
the screen 10 m (32.8 ft).
3.
Start the engine and illuminate the headlamp (LO).
NOTE:
Block light from the headlamp that is not being adjusted with a thick fabric or another object, so that it
does not reach the adjustment screen.
CAUTION:
Never cover lens surface with tape, etc. because it is made from plastic.
4.
Use the aiming adjustment screw to adjust the elbow point projected by the low beams on the screen, so
that it is within the aiming adjustment area.
Low beam distribution on the screen
Headlamp RH (UP/DOWN)
Clockwise
UP
Counterclockwise
DOWN
Adjustment screw
Screwdriver rotation
Facing direction
Aiming adjustment area
Elbow point
Headlamp center
H.
Horizontal center line of headlamp
V.
Vertical center line of headlamp
JSLIA0030ZZ
Vertical center line of headlamp H.
Horizontal center line of headlamp
L.
Distance from headlamp center to screen
X.
Aiming adjustment area
(Lateral)
Y.
Aiming adjustment area
(Vertical)
Distance from headlamp center to screen (L)
: 10 m (32.8 ft)
JSLIA0031ZZ
EXL-312
< PERIODIC MAINTENANCE >
[HALOGEN HEADLAMP]
HEADLAMP AIMING ADJUSTMENT
Unit: mm (in)
RHD
RHD : Description
INFOID:0000000010500189
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Never remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.).
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
Aiming adjustment area
Vertical direction (Y)
(Lower side from headlamp center height)
Lateral direction (X)
(Right side from headlamp center line)
Highest light axis
100 (3.94)
0 - 100 (3.94)
Target light axis
100 (3.94)
Lowest light axis
130 (5.12)
JMLIA5134ZZ
Headlamp LH (UP/DOWN)
adjustment screw
Headlamp LH (INSIDE/OUTSIDE)
adjustment screw
Headlamp RH (INSIDE/OUTSIDE)
adjustment screw
Headlamp RH (UP/DOWN)
adjustment screw
: Vehicle front
Adjustment screw
Screwdriver rotation
Facing direction
Headlamp LH (UP/DOWN)
Clockwise
UP
Counterclockwise
DOWN
HEADLAMP AIMING ADJUSTMENT
EXL-313
< PERIODIC MAINTENANCE >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
RHD : Aiming Adjustment Procedure
INFOID:0000000010500190
1.
Place the screen.
NOTE:
• Stop the vehicle at the perpendicular angle to the wall.
• Set the screen so that it is perpendicular to a level load surface.
2.
Face the vehicle squarely toward the screen and make the distance between the headlamp center and
the screen 10 m (32.8 ft).
3.
Start the engine and illuminate the headlamp (LO).
NOTE:
Block light from the headlamp that is not being adjusted with a thick fabric or another object, so that it
does not reach the adjustment screen.
CAUTION:
Never cover lens surface with tape, etc. because it is made from plastic.
4.
Use the aiming adjustment screw to adjust the elbow point projected by the low beams on the screen, so
that it is within the aiming adjustment area.
Low beam distribution on the screen
Headlamp LH (INSIDE/OUTSIDE)
Clockwise
INSIDE
Counterclockwise
OUTSIDE
Headlamp RH (INSIDE/OUTSIDE)
Clockwise
INSIDE
Counterclockwise
OUTSIDE
Headlamp RH (UP/DOWN)
Clockwise
UP
Counterclockwise
DOWN
Adjustment screw
Screwdriver rotation
Facing direction
Aiming adjustment area
Elbow point
Headlamp center
H.
Horizontal center line of headlamp
V.
Vertical center line of headlamp
JSLIA0028ZZ
Vertical center line of headlamp H.
Horizontal center line of headlamp
L.
Distance from headlamp center to screen
X.
Aiming adjustment area
(Lateral)
Y.
Aiming adjustment area
(Vertical)
JSLIA0029ZZ
EXL-314
< PERIODIC MAINTENANCE >
[HALOGEN HEADLAMP]
HEADLAMP AIMING ADJUSTMENT
Unit: mm (in)
Distance from headlamp center to screen (L)
: 10 m (32.8 ft)
Aiming adjustment area
Vertical direction (Y)
(Lower side from headlamp center height)
Lateral direction (X)
(Left side from headlamp center line)
Highest light axis
100 (3.94)
0 - 100 (3.94)
Target light axis
100 (3.94)
Lowest light axis
130 (5.12)
FRONT FOG LAMP AIMING ADJUSTMENT
EXL-315
< PERIODIC MAINTENANCE >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP AIMING ADJUSTMENT
Description
INFOID:0000000010500251
PREPARATION BEFORE ADJUSTING
NOTE:
For details, refer to the regulations in your own country.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Never remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.).
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
• Turn the aiming adjusting screw for adjustment.
• For the position and direction of the adjusting screw, refer to the
figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.
Aiming Adjustment Procedure
INFOID:0000000010500252
1.
Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
2.
Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.
3.
Start the engine. Turn the front fog lamp ON.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
4.
Adjust the cutoff line height
with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and
becomes 150 mm (5.90 in).
: DOWN
: UP
: Vehicle front
JMLIA5135ZZ
EXL-316
< PERIODIC MAINTENANCE >
[HALOGEN HEADLAMP]
FRONT FOG LAMP AIMING ADJUSTMENT
Front fog lamp light distribution on the screen
: Cutoff line
: High illuminance area
H
: Horizontal center line of front fog lamp
V
: Vertical center line of front fog lamp
X
: Cutoff line height
JPLIA0008ZZ
FRONT COMBINATION LAMP
EXL-317
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REMOVAL AND INSTALLATION
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000010437124
REMOVAL
DISASSEMBLY
Front combination lamp
Front fender panel
Radiator core support upper LH
: N·m (kg-m, in-lb)
JMLIA5090GB
EXL-318
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
FRONT COMBINATION LAMP
Removal and Installation
INFOID:0000000010437125
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-182, "Precautions for Removing Battery Terminal"
REMOVAL
1.
Remove front bumper fascia. Refer to
EXT-19, "Removal and Installation"
.
2.
Remove front combination lamp assembly mounting bolts.
3.
Pull out front combination lamp assembly forward the vehicle.
4.
Disconnect front combination lamp assembly harness connectors.
5.
Remove front combination lamp assembly.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, perform aiming adjustment. Refer to the following:
• LHD MODELS: Refer to
.
Front combination lamp housing
Seal packing
Headlamp bulb (LO)
Headlamp aiming motor
Headlamp socket cover assembly
Front combination lamp bracket
Front turn signal lamp bulb socket
Headlamp bulb (HI)
Front turn signal lamp bulb
JMLIA5091ZZ
FRONT COMBINATION LAMP
EXL-319
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
• RHD MODELS: Refer to
Replacement
INFOID:0000000010437127
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-182, "Precautions for Removing Battery Terminal"
.
• After installing the bulb, install the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned OFF.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB (HI)
LH side
1.
Remove air duct. Refer to the following.
• HRA2DDT: Refer to
EM-23, "Removal and Installation"
EM-147, "Removal and Installation"
• K9K: Refer to
EM-279, "Removal and Installation"
• R9M: Refer to
EM-380, "Removal and Installation"
2.
Disconnect headlamp bulb (HI) harness connector.
3.
Rotate headlamp socket cover assembly counterclockwise and unlock it.
4.
Remove headlamp socket cover assembly from head lamp bulb (HI).
5.
Remove retaining spring lock, and then remove headlamp bulb (HI) from front combination lamp housing.
RH side
1.
Disconnect headlamp bulb (HI) harness connector.
2.
Rotate headlamp socket cover assembly counterclockwise and unlock it.
3.
Remove headlamp socket cover assembly from headlamp bulb (HI).
4.
Remove retaining spring lock, and then remove headlamp bulb (HI) from front combination lamp housing.
HEADLAMP BULB (LO)
LH side
1.
Remove air duct. Refer to the following.
• HRA2DDT: Refer to
EM-23, "Removal and Installation"
EM-147, "Removal and Installation"
• K9K: Refer to
EM-279, "Removal and Installation"
• R9M: Refer to
EM-380, "Removal and Installation"
2.
Disconnect headlamp bulb (LO) harness connector.
3.
Rotate headlamp bulb socket (LO) counterclockwise and unlock it.
4.
Remove headlamp bulb (LO) from front combination lamp housing.
RH side
1.
Disconnect headlamp bulb (LO) harness connector.
2.
Rotate headlamp bulb socket (LO) counterclockwise and unlock it.
3.
Remove headlamp bulb (LO) from front combination lamp housing.
DAYTIME RUNNING LIGHT/ PARKING LAMP BULB
CAUTION:
Replacement of a single part is not possible due to the adoption of LED bulb. for replacement, replace
front combination lamp as a set.
FRONT TURN SIGNAL LAMP BULB
LH side
1.
Remove air duct. Refer to the following.
• HRA2DDT: Refer to
EM-23, "Removal and Installation"
EM-147, "Removal and Installation"
• K9K: Refer to
EXL-320
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
FRONT COMBINATION LAMP
• R9M: Refer to
EM-380, "Removal and Installation"
2.
Rotate front turn signal lamp bulb socket counterclockwise and unlock it.
3.
Remove front turn signal lamp bulb socket from front combination lamp housing.
4.
Remove front turn signal lamp bulb from turn signal lamp bulb socket.
RH SIDE
1.
Rotate front turn signal lamp bulb socket counterclockwise and unlock it.
2.
Remove front turn signal lamp bulb socket from front combination lamp housing.
3.
Remove front turn signal lamp bulb from turn signal lamp bulb socket.
Disassembly and Assembly
INFOID:0000000010437128
DISASSEMBLY
1.
Remove headlamp bracket mounting screws, and then remove headlamp bracket from front combination
lamp housing.
2.
Disconnect front combination lamp harness connectors.
3.
Rotate head lamp socket cover assembly counterclockwise and unlock it.
4.
Remove head lamp socket cover assembly from halogen lamp bulb (HI).
5.
Remove retaining spring lock, and then remove halogen lamp bulb (HI) from front combination lamp hous-
ing.
6.
Rotate halogen lamp bulb (LO) counterclockwise and unlock it.
7.
Remove halogen lamp bulb (LO) from front combination lamp housing.
8.
Rotate front turn signal lamp bulb socket counterclockwise and unlock it.
9.
Remove front turn signal lamp bulb socket from front combination lamp housing.
10. Remove front turn signal lamp bulb from front turn signal lamp bulb socket.
11. Remove head lamp aiming motor from front combination lamp housing.
ASSEMBLY
Note the following item, and then install in the reverse order of removal.
CAUTION:
• After installing the bulb, install the bulb socket securely watertightness.
• After installation, perform aiming adjustment. Refer to the following.
- LHD models: Refer to
.
- RHD models: Refer to
FRONT FOG LAMP
EXL-321
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP
Exploded View
INFOID:0000000010437133
Removal and Installation
INFOID:0000000010437134
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-182, "Precautions for Removing Battery Terminal"
REMOVAL
1.
Remove front fender protector to make work space. Refer to
EXT-32, "Removal and Installation"
2.
Disconnect front fog lamp harness connector.
3.
Remove front fog lamp fixing bolt, and then remove front fog lamp.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000010437135
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
Front bumper fascia
Front bumper finisher
Front fog lamp
Front fog lamp bulb
: N·m (kg-m, in-lb)
JMLIA5093GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст