Qashqai J11. Exterior Lighting system — part 19
EXL-290
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
REAR FOG LAMP CIRCUIT
REAR FOG LAMP CIRCUIT
Component Function Check
INFOID:0000000010469989
1.
CHECK REAR FOG LAMP OPERATION
With CONSULT
1.
Select “HEAD LAMP” of “BCM” using CONSULT.
2.
Select “RR FOG LAMP” in “Active Test” mode.
3.
With operating the test items, check that the rear fog lamp is turned ON.
Is the inspection result normal?
YES
>> Rear fog lamp circuit is normal.
NO
>> Refer to
EXL-290, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010469990
1.
CHECK REAR FOG LAMP OUTPUT VOLTAGE
With CONSULT
1.
Turn ignition switch OFF.
2.
Disconnect rear fog lamp connector.
3.
Turn ignition switch ON.
4.
Select “HEAD LAMP” of “BCM” using CONSULT.
5.
Select “RR FOG LAMP” in “Active Test” mode.
6.
With operating the test items, check voltage between rear fog lamp harness connector and ground.
LHD models
RHD models
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK REAR FOG LAMP POWER SUPPLY CIRCUIT (OPEN)
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and rear fog lamp harness connector.
LHD models
On
: Rear fog lamp ON
Off
: Rear fog lamp OFF
+
-
Test item
Voltage
Rear fog lamp
Connector
Terminal
B24
1
Ground
RR FOG LAMP
On
9 – 16 V
Off
0 V
+
-
Test item
Voltage
Rear fog lamp
Connector
Terminal
D83
1
Ground
RR FOG LAMP
On
9 – 16 V
Off
0 V
BCM
Rear fog lamp
Continuity
Connector
Terminal
Connector
Terminal
B3
122
B24
1
Existed
REAR FOG LAMP CIRCUIT
EXL-291
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
RHD models
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK REAR FOG LAMP POWER SUPPLY CIRCUIT (SHORT)
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harness.
4.
CHECK REAR FOG LAMP GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between rear fog lamp harness connector and ground.
LHD models
LHD models
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK REAR FOG LAMP BULB
Check rear fog lamp bulb.
Is the inspection result normal?
YES
>> Check rear fog lamp bulb socket. Repair or replace if necessary.
NO
>> Replace rear fog lamp bulb. Refer to
.
BCM
Rear fog lamp
Continuity
Connector
Terminal
Connector
Terminal
B3
122
D83
1
Existed
BCM
—
Continuity
Connector
Terminal
B3
122
Ground
Not existed
Rear fog lamp
—
Continuity
Connector
Terminal
B24
2
Ground
Existed
Rear fog lamp
—
Continuity
Connector
Terminal
D83
2
Ground
Existed
EXL-292
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
TURN SIGNAL LAMP CIRCUIT
TURN SIGNAL LAMP CIRCUIT
Component Function Check
INFOID:0000000010469992
1.
CHECK TURN SIGNAL LAMP OPERATION
1.
Turn ignition switch ON.
2.
With operating the turn signal switch, check that the turn signal lamp is blinks.
Is the inspection result normal?
YES
>> Turn signal lamp circuit is normal.
NO
>> Refer to
EXL-292, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010469993
1.
CHECK SYMPTOM
Check symptom (A or B)
Which symptom is detected?
A
>> GO TO 2.
B
>> GO TO 4.
2.
CHECK FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuse is not fusing.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
3.
CHECK BCM POWER SUPPLY (TURN SIGNAL LAMP)
1.
Disconnect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harness.
4.
CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE
1.
Turn ignition switch OFF.
2.
Disconnect the following connectors.
-
Front combination lamp
Right
: Turn signal lamps RH blink
Left
: Turn signal lamps LH blink
Center
: Turn signal lamps OFF
Symptom
A
All of turn signal lamp are not blinks
B
Applicable side performs high flasher activation
Unit
Location
Fuse No.
Capacity
BCM
Fuse block (J/B)
#33
10 A
+
-
Voltage
BCM
Connector
Terminal
M68
144
Ground
9 – 16 V
TURN SIGNAL LAMP CIRCUIT
EXL-293
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
-
Door mirror
-
Rear turn signal lamp
3.
Turn ignition switch ON.
4.
With operating the turn signal switch, check voltage between BCM harness connector and ground.
Front turn signal lamp
Side turn signal lamp
+
-
Test item
Voltage
(Approx.)
BCM
Connector
Terminal
RH
E60
168
Ground
Turn signal
switch
Right
Center
0 V
LH
167
Left
Center
0 V
+
-
Test item
Voltage
(Approx.)
BCM
Connector
Terminal
RH
M70
43
Ground
Turn signal
switch
Right
Center
0 V
LH
42
Left
Center
0 V
PKID0926E
PKID0926E
PKID0926E
PKID0926E
EXL-294
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
TURN SIGNAL LAMP CIRCUIT
Rear turn signal lamp
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 5.
5.
CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (SHORT)
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and ground.
Front turn signal lamp
Side turn signal lamp
Rear turn signal lamp
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harness.
6.
CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (OPEN)
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
+
-
Test item
Voltage
(Approx.)
BCM
Connector
Terminal
RH
B3
136
Ground
Turn signal
switch
Right
Center
0 V
LH
133
Left
Center
0 V
PKID0926E
PKID0926E
BCM
—
Continuity
Connector
Terminal
RH
E60
168
Ground
Not existed
LH
167
BCM
—
Continuity
Connector
Terminal
RH
M70
43
Ground
Not existed
LH
42
BCM
—
Continuity
Connector
Terminal
RH
B3
136
Ground
Not existed
LH
133
TURN SIGNAL LAMP CIRCUIT
EXL-295
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
3.
Check continuity between BCM harness connector and each turn signal lamp harness connector.
Front turn signal lamp
Side turn signal lamp (LHD models)
Side turn signal lamp (RHD models)
Rear turn signal lamp
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
CHECK TURN SIGNAL LAMP GROUND CIRCUIT
Check continuity between each turn signal lamp harness connector and ground.
Front turn signal lamp
Side turn signal lamp (LHD models)
Side turn signal lamp (RHD models)
BCM
Front combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E60
168
E92
6
Existed
LH
167
E90
BCM
Door mirror
Continuity
Connector
Terminal
Connector
Terminal
RH
M70
43
D27
13
Existed
LH
42
D3
BCM
Door mirror
Continuity
Connector
Terminal
Connector
Terminal
RH
M70
43
D40
13
Existed
LH
42
D16
BCM
Rear turn signal lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
B3
136
B80
1
Existed
LH
133
B23
Front combination lamp
—
Continuity
Connector
Terminal
RH
E92
1
Ground
Existed
LH
E90
Door mirror
—
Continuity
Connector
Terminal
RH
D27
14
Ground
Existed
LH
D3
Door mirror
—
Continuity
Connector
Terminal
RH
D40
14
Ground
Existed
LH
D16
EXL-296
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
TURN SIGNAL LAMP CIRCUIT
Rear turn signal lamp
Is the inspection result normal?
YES-1 >> Front turn signal lamp or rear turn signal lamp: GO TO 8.
YES-2 >> Side turn signal lamp: Replace side turn signal lamp. Refer to
EXL-323, "Removal and Installa-
.
NO
>> Repair or replace harness.
8.
CHECK TURN SIGNAL LAMP BULB
Check the applicable turn signal lamp bulb.
Is the inspection result normal?
YES
>> Check the corresponding turn signal lamp bulb socket. Repair or replace if necessary.
NO
>> Replace the corresponding turn signal lamp bulb. Refer to
signal lamp) or
(rear turn signal lamp).
Rear turn signal lamp
—
Continuity
Connector
Terminal
RH
B80
2
Ground
Existed
LH
B23
LIGHT & RAIN SENSOR
EXL-297
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LIGHT & RAIN SENSOR
Component Function Check
INFOID:0000000010469994
1.
CHECK LIGHT & RAIN SENSOR
1.
Clean light & rain sensor detection area of windshield fully.
2.
Turn ignition switch ON.
3.
Turn lighting switch AUTO.
4.
With the light & rain sensor illuminating, check the auto light function.
Is the inspection result normal?
YES
>> Light & rain sensor is normal.
NO
>> Refer to
EXL-297, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010469995
1.
CHECK LIGHT & RAIN SENSOR POWER SUPPLY
1.
Turn ignition switch OFF
2.
Disconnect light & rain sensor connector.
3.
Turn ignition switch ON.
4.
Check voltage between light & rain sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK LIGHT & RAIN SENSOR POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Remove room lamp relay.
3.
Check continuity between room lamp relay harness connector and light & rain sensor harness connector.
Is the inspection result normal?
YES
>> Perform the interior room lamp power supply circuit diagnosis. Refer to
.
NO
>> Repair or replace harness.
3.
CHECK LIGHT & RAIN SENSOR GROUND CIRCUIT
Check continuity between light & rain sensor harness connector and ground.
Condition
Auto light function
Light & rain sensor
When illuminating
Not operating
When shutting off light
Operating
+
-
Voltage
Light & rain sensor
Connector
Terminal
R5
1
Ground Battery
voltage
Room lamp relay
Light & rain sensor
Continuity
Connector
Terminal
Connector
Terminal
M80
7
R5
1
Existed
Light & rain sensor
—
Continuity
Connector
Terminal
R5
3
Ground
Existed
EXL-298
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
LIGHT & RAIN SENSOR
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK LIGHT & RAIN SENSOR SIGNAL
1.
Connect light & rain sensor connector.
2.
Turn ignition switch ON.
3.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace light & rain sensor. Refer to
EXL-327, "Removal and Installation"
NO
>> GO TO 5.
5.
CHECK LIGHT & RAIN SENSOR SIGNAL CIRCUIT (OPEN)
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and light & rain sensor connector.
3.
Check continuity between BCM harness connector and light & rain sensor harness connector.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK LIGHT & RAIN SENSOR SIGNAL CIRCUIT (SHORT)
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harness.
+
-
Condition
Voltage
(Approx.)
BCM
Connector
Terminal
M70
47
Ground
Ignition switch
ON
8.7V
JPMIA0156GB
BCM
Light & rain sensor
Continuity
Connector
Terminal
Connector
Terminal
M70
47
R5
2
Existed
BCM
—
Continuity
Connector
Terminal
M70
47
Ground
Not existed
HAZARD SWITCH
EXL-299
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HAZARD SWITCH
Component Function Check
INFOID:0000000010469997
1.
CHECK HAZARD SWITCH SIGNAL
With CONSULT
1.
Turn ignition switch ON.
2.
Select “FLASHER” of “BCM” using CONSULT.
3.
Select “HAZARD SW” in “Data Monitor” mode.
4.
With operating the hazard switch, check the monitor status.
Is the inspection result normal?
YES
>> Hazard switch circuit is normal.
NO
>> Refer to
EXL-299, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010469998
1.
CHECK HAZARD SWITCH SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect hazard switch connector.
3.
Check voltage between hazard switch connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK HAZARD SWITCH SIGNAL CIRCUIT (OPEN)
1.
Disconnect BCM connector.
2.
Check continuity between hazard switch harness connector and BCM harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK HAZARD SWITCH SIGNAL CIRCUIT (SHORT)
Check continuity between hazard switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
Monitor item
Condition
Monitor status
HAZARD SW
Hazard switch
ON
On
OFF
Off
+
-
Voltage
Hazard switch
Connector
Terminal
M39
2
Ground
9 – 16 V
Hazard switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
M39
2
M70
51
Existed
Hazard switch
—
Continuity
Connector
Terminal
M39
2
Ground
Not existed
EXL-300
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
HAZARD SWITCH
NO
>> Repair or replace harness.
4.
CHECK HAZARD SWITCH GROUND CIRCUIT
Check continuity between hazard switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK HAZARD SWITCH
Check hazard switch. Refer to
EXL-300, "Component Inspection"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace hazard switch. Refer to
EXL-325, "Removal and Installation"
Component Inspection
INFOID:0000000010469999
1.
CHECK HAZARD SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect hazard switch connector.
3.
Check continuity of hazard switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace hazard switch. Refer to
EXL-325, "Removal and Installation"
Hazard switch
—
Continuity
Connector
Terminal
M39
1
Ground
Existed
Hazard switch
Condition
Continuity
Terminal
1
2
Hazard switch
ON
Existed
OFF
Not existed
HEADLAMP AIMING SWITCH
EXL-301
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HEADLAMP AIMING SWITCH
Component Inspection
INFOID:0000000010470150
1.
CHECK HEADLAMP AIMING SWITCH
1.
Turn ignition switch OFF.
2.
Remove headlamp aiming switch.
3.
Check resistance among each headlamp aiming switch termi-
nals.
MR20DD
K9K
HRA2DDT / R9M
Is the inspection result normal?
YES
>> Headlamp aiming switch is normal.
NO
>> Replace headlamp aiming switch. Refer to
EXL-326, "Removal and Installation"
.
JMLIA3329ZZ
Headlamp aiming switch
Condition
Resistance
(Approx.)
Terminal
1
2
Switch position
0
: 140
Ω
1
: 287
Ω
2
: 499
Ω
3
: 931
Ω
3
—
: 390
Ω
Headlamp aiming switch
Condition
Resistance
(Approx.)
Terminal
1
2
Switch position
0
: 140
Ω
1
: 287
Ω
2
: 523
Ω
3
: 1050
Ω
3
—
: 390
Ω
Headlamp aiming switch
Condition
Resistance
(Approx.)
Terminal
1
2
Switch position
0
: 140
Ω
1
: 287
Ω
2
: 576
Ω
3
: 1240
Ω
3
—
: 390
Ω
EXL-302
< SYMPTOM DIAGNOSIS >
[HALOGEN HEADLAMP]
EXTERIOR LIGHTING SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000010470000
NOTE:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.
Symptom
Possible cause
Inspection item
Headlamp (HI) is not turned
ON
One side
• Headlamp (HI) power supply/
ground circuit
• Headlamp (HI) bulb
• Headlamp (HI) bulb socket
• IPDM E/R
Headlamp (HI) circuit
Refer to
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to
EXL-306, "Diagnosis Procedure"
High beam indicator lamp is not turned ON
[Headlamp (HI) is turned ON]
Combination meter
Combination meter
Data monitor “HI-BEAM IND”
Headlamp (LO) is not
turned ON
One side
• Headlamp (LO) power supply/
ground circuit
• Headlamp (LO) bulb
• IPDM E/R
Headlamp (LO) circuit
Refer to
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to
EXL-307, "Diagnosis Procedure"
Dipped beam indicator lamp is not turned ON
[Headlamp (LO) is turned ON]
Combination meter
Combination meter
Data monitor “DIPPED BEAM IND”
Each lamp is not turned ON/OFF with lighting switch
AUTO
• Combination switch input/output
signal circuit
• Combination switch
• BCM
Combination switch
Refer to
.
• Light & rain sensor power supply/
ground/signal circuit
• Light & rain sensor
• BCM
Light & rain sensor
Refer to
Parking lamp is not turned ON
• Parking lamp power supply/
ground circuit
• Front combination lamp internal
circuit
- LED (Parking lamp)
- Control circuit
- Harness
• IPDM E/R
Parking lamp circuit
Refer to
Tail lamp is not turned ON
• Tail lamp power supply/ground
circuit
• Rear combination lamp internal
circuit
- LED (Tail lamp)
- Harness
• IPDM E/R
Tail lamp circuit
Refer to
License plate lamp is not turned ON
• License plate lamp power supply/
ground circuit
• License plate lamp bulb
• License plate lamp bulb socket
License plate lamp circuit
Refer to
Parking lamp, license plate lamp and tail lamp are not
turned ON
Symptom diagnosis
“PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON”
Refer to
EXTERIOR LIGHTING SYSTEM SYMPTOMS
EXL-303
< SYMPTOM DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Position lamp indicator is not turned ON
(Parking lamp, license plate lamp and tail lamp are
turned ON)
Combination meter
Combination meter
Data monitor “LIGHT IND”
Daytime running light is not turned ON
• Daytime running light power sup-
ply/ground circuit
• Front combination lamp internal
circuit
- LED (Daytime running light)
- Control circuit
- Harness
• IPDM E/R
Daytime running light circuit
Refer to
Turn signal lamp does not
blink
Indicator lamp is normal
(All of turn signal lamp is
not blinks)
• Fuse
• BCM power supply (turn signal
lamp) circuit
• BCM
Turn signal lamp circuit
Refer to
Indicator lamp is normal
(Applicable side per-
forms high flasher activa-
tion)
• Front turn signal lamp
- Front turn signal lamp power sup-
ply/ground circuit
- Front turn signal lamp bulb
- Front turn signal lamp bulb socket
- BCM
• Side turn signal lamp
- Side turn signal lamp power sup-
ply/ground circuit
- Side turn signal lamp
- BCM
• Rear turn signal lamp
- Rear turn signal lamp power sup-
ply/ground circuit
- Rear turn signal lamp bulb
- Rear turn signal lamp bulb socket
- BCM
Indicator lamp is included
• Combination switch input/output
signal circuit
• Combination switch
• BCM
Combination switch
Refer to
.
Turn signal indicator lamp
does not blink
(Turn signal lamp is normal)
One side
Combination meter
—
Both sides
(Always)
• Turn indicator signal
• BCM
• Combination meter
Combination meter
Data monitor “TURN IND”
Both sides
(Only when activating
hazard warning lamp
with ignition switch OFF)
• Combination meter power supply/
ground circuit
• Combination meter
Combination meter
Power supply and ground circuit
Refer to
• Hazard warning lamp does not activate
(Turn signal is normal)
• Hazard warning lamp continues activating
• Hazard switch signal/ground cir-
cuit
• Hazard switch
• BCM
Symptom
Possible cause
Inspection item
EXL-304
< SYMPTOM DIAGNOSIS >
[HALOGEN HEADLAMP]
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Stop lamp and high-mount-
ed stop lamp are not turned
ON
All of stop lamp and high-
mounted stop lamp are
not turned ON
• Fuse
• BCM power supply (stop lamp)
circuit
• Stop lamp switch power supply/
signal circuit
• Stop lamp switch
• BCM
Stop lamp circuit
Refer to
Any of stop lamp and
high-mounted stop lamp
are not turned ON
• Stop lamp
- Stop lamp power supply/ground
circuit
- Rear combination lamp internal
circuit
• LED (Stop lamp)
• Harness
- BCM
• High-mounted stop lamp
- High-mounted stop lamp power
supply/ground circuit
- High-mounted stop lamp
- BCM
Front fog lamp is not turned
ON
One side
• Front fog lamp power supply/
ground circuit
• Front fog lamp bulb
• IPDM E/R
Front fog lamp circuit
Refer to
Both sides
Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to
EXL-309, "Diagnosis Procedure"
Front fog lamp indicator lamp is not turned ON
(Front fog lamp is turned ON)
Combination meter
• Combination meter
Data monitor “FR FOG IND”
• BCM (HEAD LAMP)
Active test “FR FOG LAMP”
Rear fog lamp is not turned
ON
Rear fog lamp indicator
lamp is normal
• Rear fog lamp power supply/
ground circuit
• Rear fog lamp bulb
• Rear fog lamp bulb socket
• BCM
Rear fog lamp circuit
Refer to
Rear fog lamp indicator
lamp is included
• Combination switch input/output
signal circuit
• Combination switch
• BCM
Combination switch
Refer to
.
Rear fog lamp indicator lamp is not turned ON
(Rear fog lamp is turned ON)
• Rear fog lamp status signal
• BCM
• Combination meter
• Combination meter
Data monitor “RR FOG IND”
• BCM (HEAD LAMP)
Active test “RR FOG LAMP”
Symptom
Possible cause
Inspection item
NORMAL OPERATING CONDITION
EXL-305
< SYMPTOM DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
NORMAL OPERATING CONDITION
Description
INFOID:0000000010470001
AUTO LIGHT SYSTEM
The headlamp may not be turned ON/OFF immediately after passing dark area or bright area (short tunnel,
sky bridge, shadowed area etc.) while using the auto light system. This causes for the control difference. This
is normal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст