Murano Cross Cabriolet Z51 (2013 year). Manual — part 32
EXL-30
< WIRING DIAGRAM >
[XENON TYPE]
PARKING, LICENSE PLATE AND TAIL LAMPS SYSTEM
PARKING, LICENSE PLATE AND TAIL LAMPS SYSTEM
Wiring Diagram
INFOID:0000000008460291
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JCLWA5300GB
Revision: 2012 October
2013 Murano CrossCabriolet
PARKING, LICENSE PLATE AND TAIL LAMPS SYSTEM
EXL-31
< WIRING DIAGRAM >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
JCLWA5301GB
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-32
< WIRING DIAGRAM >
[XENON TYPE]
STOP LAMP
STOP LAMP
Wiring Diagram
INFOID:0000000008460292
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JCLWA5293GB
Revision: 2012 October
2013 Murano CrossCabriolet
BACK-UP LAMP
EXL-33
< WIRING DIAGRAM >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BACK-UP LAMP
Wiring Diagram
INFOID:0000000008460293
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JCLWA5296GB
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-34
< BASIC INSPECTION >
[XENON TYPE]
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000008954751
OVERALL SEQUENCE
DETAILED FLOW
JMKIA8652GB
Revision: 2012 October
2013 Murano CrossCabriolet
DIAGNOSIS AND REPAIR WORKFLOW
EXL-35
< BASIC INSPECTION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
1.
GET INFORMATION FOR SYMPTOM
1.
Get detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurs).
2.
Check operation condition of the function that is malfunctioning.
>> GO TO 2.
2.
CHECK DTC
1.
Check DTC.
2.
Perform the following procedure if DTC is detected.
-
Record DTC and freeze frame data (Print them out using CONSULT.)
-
Erase DTC.
-
Study the relationship between the cause detected by DTC and the symptom described by the customer.
3.
Check related service bulletins for information.
Are any symptoms described and any DTC detected?
Symptom is described, DTC is detected>>GO TO 3.
Symptom is described, DTC is not detected>>GO TO 4.
Symptom is not described, DTC is detected>>GO TO 5.
3.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Also study the normal operation and fail-safe related to the symptom.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected
again. At this time, always connect CONSULT to the vehicle, and check self diagnostic results in real time.
If two or more DTCs are detected, refer to DTC INSPECTION PRIORITY CHART, and determine trouble diag-
nosis order.
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC CONFIRMATION PROCEDURE is not included on Service
Manual. This simplified check procedure is an effective alternative though DTC cannot be detected during
this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC CONFIR-
MATION PROCEDURE.
Is DTC detected?
YES
>> GO TO 7.
NO
>> Check according to
GI-40, "Intermittent Incident"
.
6.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step
4, and determine the trouble diagnosis order based on possible causes and symptom.
Is the symptom described?
YES
>> GO TO 7.
NO
>> Monitor input data from related sensors or check voltage of related module terminals using CON-
SULT.
7.
DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-36
< BASIC INSPECTION >
[XENON TYPE]
DIAGNOSIS AND REPAIR WORKFLOW
Inspect according to Diagnosis Procedure of the system.
Is malfunctioning part detected?
YES
>> GO TO 8.
NO
>> Check according to
GI-40, "Intermittent Incident"
.
8.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1.
Repair or replace the malfunctioning part.
2.
Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replace-
ment.
3.
Check DTC. If DTC is detected, erase it.
>> GO TO 9.
9.
FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the
malfunction is repaired securely.
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the
symptom is not detected.
Is DTC detected and does symptom remain?
YES-1 >> DTC is detected: GO TO 7.
YES-2 >> Symptom remains: GO TO 4.
NO
>> Before returning the vehicle to the customer, always erase DTC.
Revision: 2012 October
2013 Murano CrossCabriolet
HEADLAMP (HI) CIRCUIT
EXL-37
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DTC/CIRCUIT DIAGNOSIS
HEADLAMP (HI) CIRCUIT
Component Function Check
INFOID:0000000008460295
1.
CHECK HEADLAMP (HI) OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the headlamp switches to the high beam.
NOTE:
HI/LO is repeated 1 second each.
Does the headlamp switch to the high beam?
YES
>> Headlamp (HI) circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000008460296
1.
CHECK HEADLAMP (HI) OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1.
Turn ignition switch OFF.
2.
Disconnect high beam solenoid connector.
3.
Turn ignition switch ON.
4.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
5.
With operating test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK HEADLAMP (HI) OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and high beam solenoid harness connector.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
Hi
: Headlamp switches to the high beam.
Off
: Headlamp OFF
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
RH
E345
89
Ground
EXTERNAL LAMPS
Hi
Battery voltage
Off
0 V
LH
90
Hi
Battery voltage
Off
0 V
IPDM E/R
High beam solenoid
Continuity
Connector
Terminal
Connector
Terminal
RH
E345
89
E326
1
Existed
LH
90
E325
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-38
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
HEADLAMP (HI) CIRCUIT
3.
CHECK HEADLAMP (HI) FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuses are not fusing.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> GO TO 4.
4.
CHECK HEADLAMP (HI) SHORT CIRCUIT
1.
Disconnect IPDM E/R connector.
2.
Check continuity between IPDM E/R harness connector terminal and ground.
Is the inspection result normal?
YES
>> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO
>> Repair or replace harness. And then replace the fuse.
5.
CHECK HEADLAMP (HI) GROUND OPEN CIRCUIT
Check continuity between high beam solenoid harness connector and ground.
Is the inspection result normal?
YES
>> Replace front combination lamp.
NO
>> Repair or replace harness.
Unit
Location
Fuse No.
Capacity
Headlamp HI (RH)
IPDM E/R
#55
10 A
Headlamp HI (LH)
#54
IPDM E/R
Ground
Continuity
Connector
Terminal
RH
E345
89
Not existed
LH
90
High beam solenoid
Ground
Continuity
Connector
Terminal
RH
E326
2
Existed
LH
E325
Revision: 2012 October
2013 Murano CrossCabriolet
HEADLAMP (LO) CIRCUIT
EXL-39
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HEADLAMP (LO) CIRCUIT
Component Function Check
INFOID:0000000008460297
1.
CHECK HEADLAMP (LO) OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the headlamp (LO) is turned ON.
Is the headlamp (LO) turned ON?
YES
>> Headlamp (LO) is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000008460298
1.
CHECK HEADLAMP (LO) OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1.
Turn ignition switch OFF.
2.
Disconnect headlamp connector.
3.
Turn ignition switch ON.
4.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
5.
With operating test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK HEADLAMP (LO) OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and headlamp harness connector.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
3.
CHECK HEADLAMP (LO) FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuses are not fusing.
Lo
: Headlamp (LO) ON
Off
: Headlamp (LO) OFF
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
RH
E345
83
Ground
EXTERNAL LAMPS
Lo
Battery voltage
Off
0 V
LH
84
Lo
Battery voltage
Off
0 V
IPDM E/R
Headlamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E345
83
E324
1
Existed
LH
84
E323
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-40
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
HEADLAMP (LO) CIRCUIT
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> GO TO 4.
4.
CHECK HEADLAMP (LO) SHORT CIRCUIT
1.
Disconnect IPDM E/R connector.
2.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO
>> Repair or replace harness. And then replace the fuse.
5.
CHECK HEADLAMP (LO) GROUND OPEN CIRCUIT
Check continuity between headlamp harness connector and ground.
Is the inspection result normal?
YES
>> Perform the xenon headlamp diagnosis. Refer to
.
NO
>> Repair or replace harness.
Unit
Lotion
Fuse No.
Capacity
Headlamp LO (RH)
IPDM E/R
#57
15 A
Headlamp LO (LH)
#56
IPDM E/R
Ground
Continuity
Connector
Terminal
RH
E345
83
Not existed
LH
84
Headlamp
Ground
Continuity
Connector
Terminal
RH
E324
2
Existed
LH
E323
Revision: 2012 October
2013 Murano CrossCabriolet
XENON HEADLAMP
EXL-41
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
XENON HEADLAMP
Diagnosis Procedure
INFOID:0000000008460299
1.
CHECK XENON BULB
Install the normal bulb to the applicable headlamp. Check that the lighting switch is turned ON.
Is the headlamp turned ON?
YES
>> Replace the xenon bulb.
NO
>> GO TO 2.
2.
CHECK HID CONTROL UNIT
Install the normal HID control unit to the applicable headlamp. Check that the lighting switch is turned ON.
Is the headlamp turned ON?
YES
>> Replace HID control unit.
NO
>> Xenon headlamp is normal. Check the headlamp control system.
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-42
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
PARKING LAMP CIRCUIT
PARKING LAMP CIRCUIT
Component Function Check
INFOID:0000000008460300
1.
CHECK PARKING LAMP OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the parking lamp is turned ON.
Is the parking lamp turned ON?
YES
>> Parking lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000008460301
1.
CHECK PARKING LAMP FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuses are not fusing.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK PARKING LAMP SHORT CIRCUIT
1.
Disconnect IPDM E/R connector and parking lamp connector.
2.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace the fuse. (Replace IPDM E/R if fusing is found again.)
NO
>> Repair or replace harness. And then replace the fuse.
3.
CHECK PARKING LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace the bulb.
4.
CHECK PARKING LAMP OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1.
Disconnect parking lamp connector.
2.
Turn ignition switch ON.
3.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4.
With operating test items, check voltage between IPDM E/R harness connector and ground.
TAIL
: Parking lamp ON
Off
: Parking lamp OFF
Unit
Location
Fuse No.
Capacity
Parking lamp / Front side marker lamp
IPDM E/R
#52
10 A
IPDM E/R
Ground
Continuity
Connector
Terminal
RH
E346
91
Not existed
LH
92
Revision: 2012 October
2013 Murano CrossCabriolet
PARKING LAMP CIRCUIT
EXL-43
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace IPDM E/R.
5.
CHECK PARKING LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and parking lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK PARKING LAMP GROUND OPEN CIRCUIT
Check continuity between parking lamp harness connector and ground.
Is the inspection result normal?
YES-1 >> (When tail lamp does not turn ON) Replace rear combination lamp.
YES-2 >> (When rear side marker lamp does not turn ON) Check corresponding bulb socket and harness.
Repair or replace if necessary.
NO
>> Repair or replace harness.
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
RH
E346
91
Ground
EXTERNAL LAMPS
TAIL
Battery voltage
Off
0 V
LH
92
TAIL
Battery voltage
Off
0 V
IPDM E/R
Parking lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E346
91
E330
1
Existed
LH
92
E329
Parking lamp
Ground
Continuity
Connector
Terminal
RH
E330
2
Existed
LH
E329
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-44
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
FRONT SIDE MARKER LAMP CIRCUIT
FRONT SIDE MARKER LAMP CIRCUIT
Component Function Check
INFOID:0000000008460302
NOTE:
Check parking lamp circuit if parking lamp and front side marker lamp are not turned ON. Refer to
1.
CHECK FRONT SIDE MARKER LAMP OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the front side marker lamp is turned ON.
Is the front side marker lamp turned ON?
YES
>> Front side marker lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000008460303
1.
CHECK FRONT SIDE MARKER LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the bulb.
2.
CHECK FRONT SIDE MARKER LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector and front side marker lamp connector.
3.
Check continuity between IPDM E/R harness connector and front side marker lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK FRONT SIDE MARKER LAMP GROUND OPEN CIRCUIT
Check continuity between front side marker lamp harness connector and ground.
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
TAIL
: Front side marker lamp ON
Off
: Front side marker lamp OFF
IPDM E/R
Front side marker lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E346
91
E315
1
Existed
LH
92
E314
Front side marker lamp
Ground
Continuity
Connector
Terminal
RH
E315
2
Existed
LH
E314
Revision: 2012 October
2013 Murano CrossCabriolet
TAIL LAMP CIRCUIT
EXL-45
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
TAIL LAMP CIRCUIT
Component Function Check
INFOID:0000000008460304
1.
CHECK TAIL LAMP OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the tail lamp is turned ON.
Is the tail lamp turned ON?
YES
>> Tail lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000008460305
1.
CHECK TAIL LAMP FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuses are not fusing.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK TAIL LAMP SHORT CIRCUIT
1.
Disconnect IPDM E/R connector, rear combination lamp connector and license plate lamp connector.
2.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace the fuse. (Replace IPDM E/R if fusing is found again.)
NO
>> Repair or replace harness. And then replace the fuse.
3.
CHECK TAIL LAMP OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1.
Disconnect rear combination lamp connector.
2.
Turn ignition switch ON.
3.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4.
With operating test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace IPDM E/R.
TAIL
: Tail Lamp ON
Off
: Tail lamp OFF
Unit
Location
Fuse No.
Capacity
Tail lamp / Rear side marker lamp / License plate lamp
IPDM E/R
#53
10 A
IPDM E/R
Ground
Continuity
Connector
Terminal
E10
7
Not existed
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
E10
7
Ground
EXTERNAL
LAMPS
TAIL
Battery
voltage
Off
0 V
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст