Murano Cross Cabriolet Z51 (2013 year). Manual — part 33
EXL-46
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
TAIL LAMP CIRCUIT
4.
CHECK TAIL LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and rear combination lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK TAIL LAMP GROUND OPEN CIRCUIT
Check continuity between rear combination lamp harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear combination lamp.
NO
>> Repair or replace harness.
IPDM E/R
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E10
7
B86
4
Existed
LH
B59
Rear combination lamp
Ground
Continuity
Connector
Terminal
RH
B86
1
Existed
LH
B59
Revision: 2012 October
2013 Murano CrossCabriolet
LICENSE PLATE LAMP CIRCUIT
EXL-47
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LICENSE PLATE LAMP CIRCUIT
Component Function Check
INFOID:0000000008460306
NOTE:
Check tail lamp circuit if tail lamp and license plate lamp are not turned ON. Refer to
1.
CHECK LICENSE PLATE LAMP OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the lighting switch, check that the license plate lamp is turned ON.
Is the license plate lamp turned ON?
YES
>> License plate lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000008460307
1.
CHECK LICENSE PLATE LAMP BULB
Check the applicable lamp bulb.
Is the bulb normal?
YES
>> GO TO 2.
NO
>> Replace the bulb.
2.
CHECK LICENSE PLATE LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector and license plate lamp connector.
3.
Check continuity between IPDM E/R harness connector and license plate lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK LICENSE PLATE LAMP GROUND OPEN CIRCUIT
Check continuity between license plate lamp harness connector and ground.
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
TAIL
: License plate lamp ON
Off
: License plate lamp OFF
IPDM E/R
License plate lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E10
7
T9
1
Existed
LH
T6
License plate lamp
Ground
Continuity
Connector
Terminal
RH
T9
2
Existed
LH
T6
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-48
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
TURN SIGNAL LAMP CIRCUIT
TURN SIGNAL LAMP CIRCUIT
Component Function Check
INFOID:0000000008460308
1.
CHECK TURN SIGNAL LAMP
CONSULT ACTIVE TEST
1.
Select “FLASHER” of BCM (FLASHER) active test item.
2.
With operating the test items, check that the turn signal lamp is turned ON.
Is the turn signal lamp turned ON?
YES
>> Turn signal lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000008460309
1.
CHECK TURN SIGNAL LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the bulb.
2.
CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE
1.
Turn ignition switch OFF.
2.
Disconnect front turn signal lamp connector or rear combination lamp connector.
3.
Turn ignition switch ON.
4.
With operating turn signal switch, check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 4.
LH
: Turn signal lamps (LH) ON
RH
: Turn signal lamps (RH) ON
Off
: Turn signal lamps OFF
(+)
(
−
)
Condition
Voltage (Approx.)
BCM
Connector
Terminal
RH
M119
17
Ground
Turn signal
switch
RH
OFF
0 V
LH
18
LH
OFF
0 V
PKID0926E
PKID0926E
Revision: 2012 October
2013 Murano CrossCabriolet
TURN SIGNAL LAMP CIRCUIT
EXL-49
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
3.
CHECK TURN SIGNAL LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and front turn signal lamp or rear combination lamp
harness connector.
Front turn signal lamp
Rear turn signal lamp
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
4.
CHECK TURN SIGNAL LAMP SHORT CIRCUIT
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check each bulb socket for internal short circuit, and if check result is normal, replace BCM. Refer
to
BCS-77, "Removal and Installation"
.
NO
>> Repair or replace harness.
5.
CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT
Check continuity between front turn signal lamp or rear combination lamp and ground.
Front turn signal lamp
Rear turn signal lamp
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary
NO
>> Repair or replace harness.
BCM
Front turn signal lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
M119
17
E328
1
Existed
LH
18
E327
BCM
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
M119
17
B86
2
Existed
LH
18
B59
BCM
Ground
Continuity
Connector
Terminal
RH
M119
17
Not existed
LH
18
Front turn signal lamp
Ground
Continuity
Connector
Terminal
RH
E328
2
Existed
LH
E327
Rear combination lamp
Ground
Continuity
Connector
Terminal
RH
B86
1
Existed
LH
B59
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-50
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
FRONT FOG LAMP CIRCUIT
FRONT FOG LAMP CIRCUIT
Component Function Check
INFOID:0000000008460310
1.
CHECK FRONT FOG LAMP OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the front fog lamp is turned ON.
Is the front fog lamp turned ON?
YES
>> Front fog lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000008460311
1.
CHECK FRONT FOG LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace bulb.
2.
CHECK FRONT FOG LAMP OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1.
Turn ignition switch OFF.
2.
Disconnect front fog lamp connector.
3.
Turn ignition switch ON.
4.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
5.
With operating the test items, check the voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace IPDM E/R.
3.
CHECK FRONT FOG LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and front fog lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 4.
Fog
: Front fog lamp ON
Off
: Front fog lamp OFF
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
RH
E345
86
Ground
EXTERNAL
LAMPS
Fog
Battery voltage
Off
0 V
LH
87
Fog
Battery voltage
Off
0 V
IPDM E/R
Front fog lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E345
86
E402
1
Existed
LH
87
E412
Revision: 2012 October
2013 Murano CrossCabriolet
FRONT FOG LAMP CIRCUIT
EXL-51
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
NO
>> Repair or replace harness.
4.
CHECK FRONT FOG LAMP GROUND CIRCUIT OPEN CIRCUIT
Check continuity between front fog lamp harness connector and ground.
Is the inspection result normal?
YES
>> Refer to
GI-40, "Intermittent Incident"
.
NO
>> Repair or replace harness.
Front fog lamp
Ground
Continuity
Connector
Terminal
RH
E402
2
Existed
LH
E412
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-52
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
OPTICAL SENSOR
OPTICAL SENSOR
Component Function Check
INFOID:0000000008460312
1.
CHECK OPTICAL SENSOR SIGNAL BY CONSULT
CONSULT DATA MONITOR
1.
Turn ignition switch ON.
2.
Select “OPTICAL SENSOR” of BCM (HEADLAMP) data monitor item.
3.
Turn lighting switch AUTO.
4.
With the optical sensor illuminating, check the monitor status.
*: Illuminates the optical sensor. The value may be less than the standard value if brightness is weak.
Is the item status normal?
YES
>> Optical sensor is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000008460313
1.
CHECK OPTICAL SENSOR POWER SUPPLY INPUT
1.
Turn ignition switch ON.
2.
Turn lighting switch AUTO.
3.
Check voltage between optical sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK OPTICAL SENSOR GROUND INPUT
Check voltage between optical sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 6.
3.
CHECK OPTICAL SENSOR SIGNAL OUTPUT
With illuminating the optical sensor, check voltage between optical sensor harness connector and ground.
Monitor item
Condition
Voltage (Approx.)
OPTICAL SENSOR
Optical sensor
When illuminating
3.1 V or more *
When shutting off light
0.6 V or less
(+)
(
−
)
Voltage
(Approx.)
Optical sensor
Connector
Terminal
M17
1
Ground
5 V
Terminal
Voltage
(Approx.)
(+)
(
−
)
Optical sensor
Ground
Connector
Terminal
M17
3
0 V
Revision: 2012 October
2013 Murano CrossCabriolet
OPTICAL SENSOR
EXL-53
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
*: Illuminate the optical sensor. The value may be less than the standard if brightness is weak.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace optical sensor.
4.
CHECK OPTICAL SENSOR OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect optical sensor connector and BCM connector.
3.
Check continuity between optical sensor harness connector and BCM harness connector.
Does continuity exist?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK OPTICAL SENSOR SHORT CIRCUIT
Check continuity between optical sensor harness connector and ground.
Does continuity exist?
YES
>> Repair or replace harness.
NO
>> Replace BCM. Refer to
BCS-77, "Removal and Installation"
6.
CHECK OPTICAL SENSOR GROUND OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect optical sensor connector and BCM connector.
3.
Check continuity between optical sensor harness connector and BCM harness connector.
Does continuity exist?
YES
>> Replace BCM. Refer to
BCS-77, "Removal and Installation"
NO
>> Repair or replace harness.
7.
CHECK OPTICAL SENSOR SIGNAL OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect optical sensor connector and BCM connector.
3.
Check continuity between optical sensor harness connector and BCM harness connector.
(+)
(
−
)
Condition
Voltage
(Approx.)
Optical sensor
Connector
Terminal
M17
2
Ground
Optical sensor
When illuminating
3.1 V or more *
When shutting off light
0.6 V or less
Optical sensor
BCM
Continuity
Connector
Terminal
Connector
Terminal
M17
1
M123
138
Existed
Optical sensor
Ground
Continuity
Connector
Terminal
M17
1
Not existed
Optical sensor
BCM
Continuity
Connector
Terminal
Connector
Terminal
M17
3
M123
137
Existed
Optical sensor
BCM
Continuity
Connector
Terminal
Connector
Terminal
M17
2
M123
113
Existed
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-54
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
OPTICAL SENSOR
Does continuity exist?
YES
>> GO TO 8.
NO
>> Repair or replace harness.
8.
CHECK OPTICAL SENSOR SHORT CIRCUIT
Check continuity between optical sensor harness connector and ground.
Does continuity exist?
YES
>> Repair or replace harness.
NO
>> Replace BCM. Refer to
BCS-77, "Removal and Installation"
Optical sensor
Ground
Continuity
Connector
Terminal
M17
2
Not existed
Revision: 2012 October
2013 Murano CrossCabriolet
HAZARD SWITCH
EXL-55
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HAZARD SWITCH
Component Function Check
INFOID:0000000008460314
1.
CHECK HAZARD SWITCH SIGNAL BY CONSULT
CONSULT DATA MONITOR
1.
Turn ignition switch ON.
2.
Select “HAZARD SW” of BCM (FLASHER) data monitor item.
3.
With operating the hazard switch, check the monitor status.
Is the item status normal?
YES
>> Hazard switch circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000008460315
1.
CHECK HAZARD SWITCH SIGNAL INPUT
1.
Turn ignition switch OFF.
2.
Disconnect hazard switch connector.
3.
Check voltage between hazard switch connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK HAZARD SWITCH SIGNAL OPEN CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between hazard switch harness connector and BCM harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK HAZARD SWITCH SIGNAL SHORT CIRCUIT
Check continuity between hazard switch harness connector and ground.
Monitor item
Condition
Monitor status
HAZARD SW
Hazard switch
ON
On
OFF
Off
(+)
(
−
)
Voltage (Approx.)
Hazard switch
Connector
Terminal
M45
2
Ground
12 V
JPMIA0012GB
Hazard switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
M45
2
M122
110
Existed
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-56
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
HAZARD SWITCH
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-77, "Removal and Installation"
NO
>> Repair or replace harness.
4.
CHECK HAZARD SWITCH GROUND OPEN CIRCUIT
Check continuity between hazard switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace hazard switch.
NO
>> Repair or replace harness.
Hazard switch
Ground
Continuity
Connector
Terminal
M45
2
Not existed
Hazard switch
Ground
Continuity
Connector
Terminal
M45
1
Existed
Revision: 2012 October
2013 Murano CrossCabriolet
EXTERIOR LIGHTING SYSTEM SYMPTOMS
EXL-57
< SYMPTOM DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
SYMPTOM DIAGNOSIS
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000008460316
CAUTION:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-
sis if any DTC is detected.
Symptom
Possible cause
Inspection item
Headlamp does not
switch to the high beam.
One side
• Fuse
• Harness between IPDM E/R
and high beam solenoid
• Harness between high beam
solenoid and ground
• Front combination lamp
(High beam solenoid)
• IPDM E/R
Headlamp (HI) circuit
Refer to
.
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM”
Refer to
High beam indicator lamp is not turned ON.
(The headlamp switches to the high beam.)
Combination meter
• Combination meter
Data monitor “HI-BEAM IND”
• BCM (HEAD LAMP)
Active test “HEADLAMP”
Headlamp does not
switch to the low beam.
One side
Front combination lamp (High
beam solenoid)
—
Both sides
• Combination switch
• Harness between combination
switch and BCM
• BCM
Combination switch
Refer to
.
High beam request signal
• BCM
• IPDM E/R
IPDM E/R
Data monitor “HL HI REQ”
IPDM E/R
—
Headlamp is not turned
ON.
One side
• Fuse
• Xenon bulb
• Harness between IPDM E/R
and headlamp
• Harness between headlamp
and ground
• Front combination lamp (xenon
headlamp)
• IPDM E/R
Headlamp (LO) circuit
Refer to
.
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to
Headlamp is not turned ON/OFF with the lighting
switch AUTO.
• Combination switch
• Harness between combination
switch and BCM
• BCM
Combination switch
Refer to
.
• Optical sensor
• Harness between optical sen-
sor and BCM
• BCM
Optical sensor
Refer to
.
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-58
< SYMPTOM DIAGNOSIS >
[XENON TYPE]
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Front fog lamp is not
turned ON.
One side
• Front fog lamp bulb
• Harness between IPDM E/R
and front fog lamp
• Harness between front fog lamp
and ground
• IPDM E/R
Front fog lamp circuit
Refer to
.
Both side
Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to
Parking lamp is not turned ON.
• Parking lamp bulb
• Harness between IPDM E/R
and parking lamp
• Harness between parking lamp
and ground
Parking lamp circuit
Refer to
.
Front side marker lamp is not turned ON.
• Front side marker lamp bulb
• Harness between IPDM E/R
and front side marker lamp
• Harness between front side
marker lamp and ground
Front side marker lamp circuit
Refer to
.
Parking lamp and front side marker lamp are not
turned ON.
• Fuse
• Harness between IPDM E/R
and parking lamp
• IPDM E/R
Parking lamp circuit
Refer to
.
Tail lamp / Rear side marker lamp is not turned ON.
• Rear side marker lamp bulb
• Rear combination lamp
• Harness between IPDM E/R
and rear combination lamp
• Harness between rear combi-
nation lamp and ground
Tail lamp circuit
Refer to
.
License plate lamp is not turned ON.
• License plate lamp bulb
• Harness between IPDM E/R
and license plate lamp
• Harness between license plate
lamp and ground
License plate lamp circuit
Refer to
.
Tail lamp and license plate lamp are not turned ON.
• Fuse
• Harness between IPDM E/R
and rear combination lamp
• IPDM E/R
License plate lamp circuit
Refer to
.
Parking lamp, tail lamp, side marker lamp and li-
cense plate lamp are not turned ON.
Symptom diagnosis
“PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED
ON”
Refer to
Turn signal lamp does not
blink.
Indicator lamp is nor-
mal.
(Applicable side per-
forms high flasher acti-
vation.)
• Turn signal lamp bulb
• Harness between BCM and
each turn signal lamp
• Harness between each turn sig-
nal lamp and ground
Turn signal lamp circuit
Refer to
.
Indicator lamp is includ-
ed
• Combination switch
• Harness between combination
switch and BCM
• BCM
Combination switch
Refer to
.
Symptom
Possible cause
Inspection item
Revision: 2012 October
2013 Murano CrossCabriolet
EXTERIOR LIGHTING SYSTEM SYMPTOMS
EXL-59
< SYMPTOM DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Turn signal indicator lamp
does not blink.
(Turn signal indicator
lamp is normal.)
One side
Combination meter
—
Both sides
(Always)
• Turn indicator signal
• Combination meter
• BCM
• Combination meter
• Combination meter
Data monitor “TURN IND”
• BCM (FLASHER)
Active test “FLASHER”
Both sides
(Only when activating
hazard warning lamp
with ignition switch
OFF)
• Combination meter power sup-
ply and ground circuit
• Combination meter
Combination meter
Power supply and ground circuit
Refer to
• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)
• Hazard switch
• Harness between hazard
switch and BCM
• Harness between hazard
switch and ground
• BCM
Hazard switch
Refer to
.
Symptom
Possible cause
Inspection item
Revision: 2012 October
2013 Murano CrossCabriolet
EXL-60
< SYMPTOM DIAGNOSIS >
[XENON TYPE]
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
Description
INFOID:0000000008460317
XENON HEADLAMP
• Brightness and the color of light may change slightly immediately after turning the headlamp ON until the
xenon bulb becomes stable. This is normal.
• Illumination time lag may occur between right and left. This is normal.
AUTO LIGHT SYSTEM
The headlamp may not be turned ON/OFF immediately after passing dark area or bright area (short tunnel,
sky bridge, shadowed area etc.) while using the auto light system. This causes the control difference. This is
normal.
Revision: 2012 October
2013 Murano CrossCabriolet
BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM
EXL-61
< SYMPTOM DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM
Description
INFOID:0000000008460318
The headlamp (both sides) does not switch to the high beam when setting to the lighting switch HI or PASS.
Diagnosis Procedure
INFOID:0000000008460319
1.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
Is the combination switch normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “HL HI REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the item status normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
BCS-77, "Removal and Installation"
3.
HEADLAMP (HI) CIRCUIT INSPECTION
Check the headlamp (HI) circuit. Refer to
EXL-37, "Component Function Check"
Is the headlamp (HI) circuit normal?
YES
>> Refer to
GI-40, "Intermittent Incident"
.
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
HL HI REQ
Lighting switch
(2ND)
HI or PASS
ON
Except for HI or PASS
OFF
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст