Murano Cross Cabriolet Z51 (2013 year). Manual — part 108
WW-12
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
*:Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
Service item
Setting item
Description
WIPER SPEED
SETTING
On
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
Off*
Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)
Monitor Item
[Unit]
Description
PUSH SW
[Off/On]
The switch status input from push-button ignition switch
VEH SPEED 1
[km/h]
Displays the value of the vehicle speed signal received from combination meter via CAN com-
munication
FR WIPER HI
[Off/On]
Status of each switch judged by BCM using the combination switch reading function
FR WIPER LOW
[Off/On]
FR WASHER SW
[Off/On]
FR WIPER INT
[Off/On]
FR WIPER STOP
[Off/On]
Displays the status of the front wiper stop position signal received from IPDM E/R via CAN
communication.
INT VOLUME
[1
−
7]
Status of each switch judged by BCM using the combination switch reading function
H/L WASH SW
[Off/On]
NOTE:
The item is indicated, but not monitored
Test item
Operation
Description
FR WIPER
Hi
Transmits the front wiper request signal (HI) to IPDM E/R via CAN communication to op-
erate the front wiper HI operation.
Lo
Transmits the front wiper request signal (LO) to IPDM E/R via CAN communication to
operate the front wiper LO operation.
INT
Transmits the front wiper request signal (INT) to IPDM E/R via CAN communication to
operate the front wiper INT operation.
Off
Stops transmitting the front wiper request signal to stop the front wiper operation.
Revision: 2012 October
2013 Murano CrossCabriolet
DIAGNOSIS SYSTEM (IPDM E/R)
WW-13
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
DIAGNOSIS SYSTEM (IPDM E/R)
Diagnosis Description
INFOID:0000000008954746
AUTO ACTIVE TEST
Description
In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp
• Front wiper (LO, HI)
• Parking lamp
• License plate lamp
• Side maker lamp
• Tail lamp
• Front fog lamp
• Headlamp (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan
Operation Procedure
NOTE:
Never perform auto active test in the following conditions.
• CONSULT is connected
• Passenger door is open
1.
Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2.
Turn the ignition switch OFF.
3.
Turn the ignition switch ON, and within 20 seconds, press the front door switch (driver side) 10 times.
Then turn the ignition switch OFF.
4.
Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
5.
After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
• When auto active test has to be cancelled halfway through test, turn the ignition switch OFF.
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to
Inspection in Auto Active Test Mode
When auto active test mode is actuated, the following 6 steps are repeated 3 times.
Operation
sequence
Inspection location
Operation
1
Oil pressure warning lamp
Blinks continuously during operation of auto active test
2
Front wiper motor
LO for 5 seconds
→
HI for 5 seconds
3
• Parking lamp
• License plate lamp
• Side maker lamp
• Tail lamp
• Front fog lamp
10 seconds
4
Headlamp
LO
⇔
HI 5 times
5
A/C compressor (magnet clutch)
ON
⇔
OFF 5 times
6
Cooling fan
LO for 5 seconds
→
MID for 3 seconds
→
HI for 2 seconds
Revision: 2012 October
2013 Murano CrossCabriolet
WW-14
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (IPDM E/R)
Concept of auto active test
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode
JMMIA0836GB
Symptom
Inspection contents
Possible cause
Any of the following components do not operate
• Parking lamp
• License plate lamp
• Side maker lamp
• Tail lamp
• Front fog lamp
• Headlamp (HI, LO)
• Front motor wiper
Perform auto active test.
Does the applicable system
operate?
YES
BCM signal input circuit
NO
• Lamp or motor
• Lamp or motor ground circuit
• Harness or connector between
IPDM E/R and applicable system
• IPDM E/R
A/C compressor does not operate
Perform auto active test.
Does the magnet clutch oper-
ate?
YES
• A/C amp. signal input circuit
• CAN communication signal between
A/C amp. and ECM
• CAN communication signal between
ECM and IPDM E/R
NO
• Magnet clutch
• Harness or connector between
IPDM E/R and magnet clutch
• IPDM E/R
Oil pressure warning lamp does not operate
Perform auto active test.
Does the oil pressure warning
lamp blink?
YES
• Harness or connector between
IPDM E/R and oil pressure switch
• Oil pressure switch
• IPDM E/R
NO
• CAN communication signal between
IPDM E/R and BCM
• CAN communication signal between
BCM and combination meter
• Combination meter
Revision: 2012 October
2013 Murano CrossCabriolet
DIAGNOSIS SYSTEM (IPDM E/R)
WW-15
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
CONSULT Function (IPDM E/R)
INFOID:0000000008954747
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
SELF DIAGNOSTIC RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Cooling fan does not operate
Perform auto active test.
Does the cooling fan operate?
YES
• ECM signal input circuit
• CAN communication signal between
ECM and IPDM E/R
NO
• Harness or connector between
IPDM E/R and cooling fan motor
• Harness or connector between
IPDM E/R and cooling fan relay
• Cooling fan motor
• Cooling fan relay
• IPDM E/R
Symptom
Inspection contents
Possible cause
Diagnosis mode
Description
Ecu Identification
Allows confirmation of IPDM E/R part number.
Self Diagnostic Result
Displays the diagnosis results judged by IPDM E/R.
Data Monitor
Displays the real-time input/output data from IPDM E/R input/output data.
Active Test
IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor
The results of transmit/receive diagnosis of CAN communication can be read.
Monitor Item
[Unit]
MAIN SIG-
NALS
Description
MOTOR FAN REQ
[1/2/3/4]
×
Displays the value of the cooling fan speed request signal received from ECM via
CAN communication.
AC COMP REQ
[Off/On]
×
Displays the status of the A/C compressor request signal received from ECM via
CAN communication.
TAIL&CLR REQ
[Off/On]
×
Displays the status of the position light request signal received from BCM via CAN
communication.
HL LO REQ
[Off/On]
×
Displays the status of the low beam request signal received from BCM via CAN
communication.
HL HI REQ
[Off/On]
×
Displays the status of the high beam request signal received from BCM via CAN
communication.
FR FOG REQ
[Off/On]
×
Displays the status of the front fog light request signal received from BCM via
CAN communication.
FR WIP REQ
[Stop/1LOW/Low/Hi]
×
Displays the status of the front wiper request signal received from BCM via CAN
communication.
WIP AUTO STOP
[STOP P/ACT P]
×
Displays the status of the front wiper auto stop signal judged by IPDM E/R.
WIP PROT
[Off/BLOCK]
×
Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
IGN RLY1 -REQ
[Off/On]
Displays the status of the ignition switch ON signal received from BCM via CAN
communication.
IGN RLY
[Off/On]
×
Displays the status of the ignition relay judged by IPDM E/R.
Revision: 2012 October
2013 Murano CrossCabriolet
WW-16
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (IPDM E/R)
ACTIVE TEST
PUSH SW
[Off/On]
Displays the status of the push-button ignition switch judged by IPDM E/R.
INTER/NP SW
[Off/On]
Displays the status of the shift position judged by IPDM E/R.
ST RLY CONT
[Off/On]
Displays the status of the starter relay status signal received from BCM via CAN
communication.
IHBT RLY -REQ
[Off/On]
Displays the status of the starter control relay signal received from BCM via CAN
communication.
ST/INHI RLY
[Off/ ST ON/INHI ON/UNKWN]
Displays the status of the starter relay and starter control relay judged by IPDM
E/R.
DETENT SW
[Off/On]
Displays the status of the CVT shift selector (detention switch) judged by IPDM E/
R.
S/L RLY -REQ
[Off/On]
NOTE:
The item is indicated, but not monitored.
S/L STATE
[LOCK/UNLOCK/UNKWN]
NOTE:
The item is indicated, but not monitored.
DTRL REQ
[Off/On]
NOTE:
The item is indicated, but not monitored.
OIL P SW
[Open/Close]
Displays the status of the oil pressure switch judged by IPDM E/R.
HOOD SW
[Off/On]
NOTE:
The item is indicated, but not monitored.
HL WASHER REQ
[Off/On]
NOTE:
The item is indicated, but not monitored.
THFT HRN REQ
[Off/On]
Displays the status of the theft warning horn request signal received from BCM
via CAN communication.
HORN CHIRP
[Off/On]
Displays the status of the horn reminder signal received from BCM via CAN com-
munication.
CRNRNG LMP REQ
[Off/On]
NOTE:
The item is indicated, but not monitored.
Monitor Item
[Unit]
MAIN SIG-
NALS
Description
Test item
Operation
Description
CORNERING LAMP
Off
NOTE:
The item is indicated, but cannot be tested.
LH
RH
HORN
On
Operates horn relay for 20 ms.
FRONT WIPER
Off
OFF
Lo
Operates the front wiper relay.
Hi
Operates the front wiper relay and front wiper high relay.
MOTOR FAN
1
OFF
2
Operates the cooling fan relay-1.
3
Operates the cooling fan relay-2.
4
Operates the cooling fan relay-2 and cooling fan relay-3.
HEAD LAMP WASHER
On
NOTE:
The item is indicated, but cannot be tested.
Revision: 2012 October
2013 Murano CrossCabriolet
DIAGNOSIS SYSTEM (IPDM E/R)
WW-17
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
EXTERNAL LAMPS
Off
OFF
TAIL
Operates the tail lamp relay.
Lo
Operates the headlamp low relay.
Hi
Operates the headlamp low relay and ON/OFF the headlamp high relay at 1 sec-
ond intervals.
Fog
Operates the front fog lamp relay.
Test item
Operation
Description
Revision: 2012 October
2013 Murano CrossCabriolet
WW-18
< ECU DIAGNOSIS INFORMATION >
BCM, IPDM E/R
ECU DIAGNOSIS INFORMATION
BCM, IPDM E/R
List of ECU Reference
INFOID:0000000008463023
ECU
Reference
BCM
BCS-54, "DTC Inspection Priority Chart"
IPDM E/R
Revision: 2012 October
2013 Murano CrossCabriolet
WIPER AND WASHER SYSTEM
WW-19
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WIRING DIAGRAM
WIPER AND WASHER SYSTEM
Wiring Diagram
INFOID:0000000008463024
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JRLWC2944GB
Revision: 2012 October
2013 Murano CrossCabriolet
WW-20
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORK FLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000008463025
OVERALL SEQUENCE
DETAILED FLOW
JMKIA8652GB
Revision: 2012 October
2013 Murano CrossCabriolet
DIAGNOSIS AND REPAIR WORK FLOW
WW-21
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
1.
GET INFORMATION FOR SYMPTOM
1.
Get detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurs).
2.
Check operation condition of the function that is malfunctioning.
>> GO TO 2.
2.
CHECK DTC
1.
Check DTC.
2.
Perform the following procedure if DTC is detected.
-
Record DTC and freeze frame data (Print them out using CONSULT.)
-
Erase DTC.
-
Study the relationship between the cause detected by DTC and the symptom described by the customer.
3.
Check related service bulletins for information.
Are any symptoms described and any DTC detected?
Symptom is described, DTC is detected>>GO TO 3.
Symptom is described, DTC is not detected>>GO TO 4.
Symptom is not described, DTC is detected>>GO TO 5.
3.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Also study the normal operation and fail-safe related to the symptom.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected
again. At this time, always connect CONSULT to the vehicle, and check self diagnostic results in real time.
If two or more DTCs are detected, refer to
BCS-54, "DTC Inspection Priority Chart"
(BCM) or
(IPDM E/R), and determine trouble diagnosis order.
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC CONFIRMATION PROCEDURE is not included on Service
Manual. This simplified check procedure is an effective alternative though DTC cannot be detected during
this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC CONFIR-
MATION PROCEDURE.
Is DTC detected?
YES
>> GO TO 7.
NO
>> Check according to
GI-40, "Intermittent Incident"
.
6.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step
4, and determine the trouble diagnosis order based on possible causes and symptom.
Is the symptom described?
YES
>> GO TO 7.
NO
>> Monitor input data from related sensors or check voltage of related module terminals using CON-
SULT.
7.
DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE
Revision: 2012 October
2013 Murano CrossCabriolet
WW-22
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORK FLOW
Inspect according to Diagnosis Procedure of the system.
Is malfunctioning part detected?
YES
>> GO TO 8.
NO
>> Check according to
GI-40, "Intermittent Incident"
.
8.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1.
Repair or replace the malfunctioning part.
2.
Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replace-
ment.
3.
Check DTC. If DTC is detected, erase it.
>> GO TO 9.
9.
FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the
malfunction is repaired securely.
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the
symptom is not detected.
Is DTC detected and does symptom remain?
YES-1 >> DTC is detected: GO TO 7.
YES-2 >> Symptom remains: GO TO 4.
NO
>> Before returning the vehicle to the customer, always erase DTC.
Revision: 2012 October
2013 Murano CrossCabriolet
FRONT WIPER MOTOR LO CIRCUIT
WW-23
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
DTC/CIRCUIT DIAGNOSIS
FRONT WIPER MOTOR LO CIRCUIT
Component Function Check
INFOID:0000000008463026
1.
CHECK FRONT WIPER LO OPERATION
CONSULT ACTIVE TEST
1.
Select “FRONT WIPER” of IPDM E/R active test item.
2.
With operating the test item, check front wiper operation.
Is front wiper (LO) operation normally?
YES
>> Front wiper motor LO circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000008463027
1.
CHECK FRONT WIPER MOTOR (LO) OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1.
Turn ignition switch OFF.
2.
Disconnect front wiper motor connector.
3.
Turn ignition switch ON.
4.
Select “FRONT WIPER” of IPDM E/R active test item.
5.
With operating the test item, check voltage between front wiper motor harness connector and ground.
Is the inspection result normal?
YES
>> Replace front wiper motor.
NO
>> GO TO 2.
2.
CHECK FRONT WIPER MOTOR (LO) CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace harness.
Lo
: Front wiper (LO) operation
Off
: Stop the front wiper.
(+)
(
−
)
Condition
Voltage (Approx.)
Front wiper motor
Connector
Terminal
E12
1
Ground
FRONT WIPER
Lo
Battery voltage
Off
0 V
IPDM E/R
Front wiper motor
Continuity
Connector
Terminal
Connector
Terminal
E10
4
E12
1
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E10
4
Not existed
Revision: 2012 October
2013 Murano CrossCabriolet
WW-24
< DTC/CIRCUIT DIAGNOSIS >
FRONT WIPER MOTOR HI CIRCUIT
FRONT WIPER MOTOR HI CIRCUIT
Component Function Check
INFOID:0000000008463028
1.
CHECK FRONT WIPER HI OPERATION
CONSULT ACTIVE TEST
1.
Select “FRONT WIPER” of IPDM E/R active test item.
2.
With operating the test item, check front wiper operation.
Is front wiper (HI) operation normally?
YES
>> Front wiper motor HI circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000008463029
1.
CHECK FRONT WIPER MOTOR (HI) OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1.
Turn ignition switch OFF.
2.
Disconnect front wiper motor connector.
3.
Turn ignition switch ON.
4.
Select “FRONT WIPER” of IPDM E/R active test item.
5.
With operating the test item, check voltage between front wiper motor harness connector and ground.
Is the inspection result normal?
YES
>> Replace front wiper motor.
NO
>> GO TO 2.
2.
CHECK FRONT WIPER MOTOR (HI) CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace harness.
Hi
: Front wiper (HI) operation
Off
: Stop the front wiper.
(+)
(
−
)
Condition
Voltage (Approx.)
Front wiper motor
Connector
Terminal
E12
4
Ground
FRONT WIPER
Hi
Battery voltage
Off
0 V
IPDM E/R
Front wiper motor
Continuity
Connector
Terminal
Connector
Terminal
E10
5
E12
4
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E10
5
Not existed
Revision: 2012 October
2013 Murano CrossCabriolet
FRONT WIPER STOP POSITION SIGNAL CIRCUIT
WW-25
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER STOP POSITION SIGNAL CIRCUIT
Component Function Check
INFOID:0000000008463030
1.
CHECK FRONT WIPER STOP POSITION SIGNAL
CONSULT DATA MONITOR
1.
Select “WIP AUTO STOP” of IPDM E/R data monitor item.
2.
Operate the front wiper.
3.
With the front wiper operation, check the monitor status.
Is the status of item normal?
YES
>> Front wiper stop position signal circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000008463031
1.
CHECK IPDM E/R OUTPUT VOLTAGE
1.
Turn ignition switch OFF.
2.
Disconnect front wiper motor connector.
3.
Turn ignition switch ON.
4.
Check voltage between front wiper motor harness connector and ground.
Is the inspection result normal?
YES
>> Replace front wiper motor.
NO
>> GO TO 2.
2.
CHECK FRONT WIPER MOTOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace harness.
Monitor item
Condition
Monitor status
WIP AUTO STOP
Front wiper motor
Stop position
STOP P
Except stop position
ACT P
(+)
(
−
)
Voltage (Approx.)
Front wiper motor
Connector
Terminal
E12
5
Ground
Battery voltage
IPDM E/R
Front wiper motor
Continuity
Connector
Terminal
Connector
Terminal
E10
16
E12
5
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E10
16
Not existed
Revision: 2012 October
2013 Murano CrossCabriolet
WW-26
< DTC/CIRCUIT DIAGNOSIS >
FRONT WIPER MOTOR GROUND CIRCUIT
FRONT WIPER MOTOR GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000008463032
1.
CHECK FRONT WIPER MOTOR GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect front wiper motor connector.
3.
Check continuity between front wiper motor harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace harness.
Front wiper motor
Ground
Continuity
Connector
Terminal
E12
2
Existed
Revision: 2012 October
2013 Murano CrossCabriolet
WASHER SWITCH
WW-27
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WASHER SWITCH
Description
INFOID:0000000008463033
Washer switch is integrated with combination switch.
Component Inspection
INFOID:0000000008463034
1.
CHECK WIPER SWITCH
1.
Turn the ignition switch OFF.
2.
Disconnect combination switch connector.
3.
Check continuity between the combination switch terminals.
Does continuity exist?
YES
>> Wiper and washer switch is normal.
NO
>> Replace wiper and washer switch.
JPLIA0310ZZ
Combination switch
Condition
Continuity
Terminal
1
6
Front washer switch ON
Existed
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст