Murano Cross Cabriolet Z51 (2013 year). Manual — part 93
B1291 POP-UP ROLL BAR RH
SRC-153
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
1.
Replace pop-up roll bar RH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-154
< DTC/CIRCUIT DIAGNOSIS >
B1292 POP-UP ROLL BAR RH
B1292 POP-UP ROLL BAR RH
Description
INFOID:0000000008461940
When diagnosis sensor unit detects acceleration that the vehicle rolls over in the lateral direction, pop-up roll
bar is activated so that the heads of rear passengers are protected.
DTC Logic
INFOID:0000000008461941
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-154, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461942
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE POP-UP ROLL BAR
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1292
RH POP-UP BAR
[SHORT]
Pop-up roll bar RH circuits are shorted to
each other
• Disconnection of wiring harness and short
• Malfunction in pop-up roll bar RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
B1292 POP-UP ROLL BAR RH
SRC-155
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
1.
Replace pop-up roll bar RH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-156
< DTC/CIRCUIT DIAGNOSIS >
B1294 POP-UP ROLL BAR LH
B1294 POP-UP ROLL BAR LH
Description
INFOID:0000000008461943
When diagnosis sensor unit detects acceleration that the vehicle rolls over in the lateral direction, pop-up roll
bar is activated so that the heads of rear passengers are protected.
DTC Logic
INFOID:0000000008461944
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-156, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461945
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE POP-UP ROLL BAR
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1294
LH POP-UP BAR
[OPEN]
Pop-up roll bar LH circuit is open
• Disconnection of wiring harness and open
• Malfunction in pop-up roll bar LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
B1294 POP-UP ROLL BAR LH
SRC-157
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
1.
Replace pop-up roll bar LH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-158
< DTC/CIRCUIT DIAGNOSIS >
B1295 POP-UP ROLL BAR LH
B1295 POP-UP ROLL BAR LH
Description
INFOID:0000000008461946
When diagnosis sensor unit detects acceleration that the vehicle rolls over in the lateral direction, pop-up roll
bar is activated so that the heads of rear passengers are protected.
DTC Logic
INFOID:0000000008461947
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-158, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461948
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE POP-UP ROLL BAR
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1295
LH POP-UP BAR
[VB-SHORT]
Pop-up roll bar LH circuit is shorted to
power supply circuit
• Disconnection of wiring harness and short
• Malfunction in pop-up roll bar LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
B1295 POP-UP ROLL BAR LH
SRC-159
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
1.
Replace pop-up roll bar LH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-160
< DTC/CIRCUIT DIAGNOSIS >
B1296 POP-UP ROLL BAR LH
B1296 POP-UP ROLL BAR LH
Description
INFOID:0000000008461949
When diagnosis sensor unit detects acceleration that the vehicle rolls over in the lateral direction, pop-up roll
bar is activated so that the heads of rear passengers are protected.
DTC Logic
INFOID:0000000008461950
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-160, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461951
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE POP-UP ROLL BAR
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1296
LH POP-UP BAR
[GND-SHORT]
Pop-up roll bar LH circuit is shorted to
ground
• Disconnection of wiring harness and short
• Malfunction in pop-up roll bar LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
B1296 POP-UP ROLL BAR LH
SRC-161
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
1.
Replace pop-up roll bar LH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-162
< DTC/CIRCUIT DIAGNOSIS >
B1297 POP-UP ROLL BAR LH
B1297 POP-UP ROLL BAR LH
Description
INFOID:0000000008461952
When diagnosis sensor unit detects acceleration that the vehicle rolls over in the lateral direction, pop-up roll
bar is activated so that the heads of rear passengers are protected.
DTC Logic
INFOID:0000000008461953
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-162, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461954
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE POP-UP ROLL BAR
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1297
LH POP-UP BAR
[SHORT]
Pop-up roll bar LH circuits are shorted to
each other
• Disconnection of wiring harness and short
• Malfunction in pop-up roll bar LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
B1297 POP-UP ROLL BAR LH
SRC-163
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
1.
Replace pop-up roll bar LH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-164
< DTC/CIRCUIT DIAGNOSIS >
B1298 POP-UP ROLL BAR
B1298 POP-UP ROLL BAR
Description
INFOID:0000000008461955
The pop-up roll bar is activated by the air bag diagnosis sensor unit signal at the time of rollover.
DTC Logic
INFOID:0000000008461956
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-164, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461957
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor)
• Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK POP-UP ROLL BAR
Check whether or not pop-up roll bar is activated in the past.
Is activation detected?
YES
>> Replace pop-up roll bar. Refer to
NO
>> GO TO 2.
2.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace harness connectors.
3.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace wiring harness.
4.
FINAL CHECK
Perform “AIR BAG” Self Diagnostic Result with CONSULT and/or air bag warning lamp status.
Is the inspection result normal?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1298
POP-UP BAR [DEPLOYED]
Pop-up roll bar is deployed
—
Revision: 2012 October
2013 Murano CrossCabriolet
B1298 POP-UP ROLL BAR
SRC-165
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> INSPECTION END
NO
>> Check the intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-166
< DTC/CIRCUIT DIAGNOSIS >
B1336, B1337 SATELLITE SENSOR RH
B1336, B1337 SATELLITE SENSOR RH
DTC Logic
INFOID:0000000008461958
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-166, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461959
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE FRONT DOOR SATELLITE SENSOR
1.
Replace front door satellite sensor RH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
DTC
Display contents of CON-
SULT
DTC detecting condition
Possible cause
B1336
B1337
FR-RH DOOR SATEL
SENS
[SENSOR MALFUNC-
TION]
Front door satellite sensor RH is malfunc-
tioning
• Harness or connectors
• Malfunction in front door satellite sensor RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
B1336, B1337 SATELLITE SENSOR RH
SRC-167
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-168
< DTC/CIRCUIT DIAGNOSIS >
B1338, B1340, B1341, B1342 SATELLITE SENSOR RH
B1338, B1340, B1341, B1342 SATELLITE SENSOR RH
DTC Logic
INFOID:0000000008461960
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-168, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461961
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE FRONT DOOR SATELLITE SENSOR
1.
Replace front door satellite sensor RH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1338
B1340
B1341
B1342
FR-RH DOOR SATEL
SENS
[COMM MALFUNC-
TION]
Front door satellite sensor RH is malfunc-
tioning
• Harness or connectors
• Malfunction in front door satellite sensor RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст