Murano Cross Cabriolet Z51 (2013 year). Manual — part 94
B1338, B1340, B1341, B1342 SATELLITE SENSOR RH
SRC-169
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-170
< DTC/CIRCUIT DIAGNOSIS >
B1339 SATELLITE SENSOR RH
B1339 SATELLITE SENSOR RH
DTC Logic
INFOID:0000000008461962
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-170, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461963
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
REPLACE FRONT DOOR SATELLITE SENSOR
1.
Replace front door satellite sensor RH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1339
FR-RH DOOR SATEL
SENS
[MIS-INSTALLATION]
Front door satellite sensor RH is out of the
specified specification
Diagnosis sensor unit or front door satellite sen-
sor RH is different from the part specified
Revision: 2012 October
2013 Murano CrossCabriolet
B1343, B1344 SATELLITE SENSOR LH
SRC-171
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1343, B1344 SATELLITE SENSOR LH
DTC Logic
INFOID:0000000008461964
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-171, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461965
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE FRONT DOOR SATELLITE SENSOR
1.
Replace front door satellite sensor LH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1343
B1344
FR-LH DOOR SATEL
SENS
[SENSOR MALFUNC-
TION]
Front door satellite sensor LH is malfunc-
tioning
• Harness or connectors
• Malfunction in front door satellite sensor LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-172
< DTC/CIRCUIT DIAGNOSIS >
B1343, B1344 SATELLITE SENSOR LH
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
B1345, B1347, B1348, B1349 SATELLITE SENSOR LH
SRC-173
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1345, B1347, B1348, B1349 SATELLITE SENSOR LH
DTC Logic
INFOID:0000000008461966
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-176, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461967
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SATELLITE SENSOR
1.
Replace front door satellite sensor LH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1345
B1347
B1348
B1349
FR-LH DOOR SATEL
SENS
[COMM MALFUNC-
TION]
Front door satellite sensor LH is malfunc-
tioning
• Harness or connectors
• Malfunction in front door satellite sensor LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-174
< DTC/CIRCUIT DIAGNOSIS >
B1345, B1347, B1348, B1349 SATELLITE SENSOR LH
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
B1346 SATELLITE SENSOR LH
SRC-175
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1346 SATELLITE SENSOR LH
DTC Logic
INFOID:0000000008461968
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-175, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461969
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
REPLACE FRONT DOOR SATELLITE SENSOR
1.
Replace front door satellite sensor LH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1346
FR-LH DOOR SATEL
SENS
[MIS-INSTALLATION]
Front door satellite sensor LH is out of the
specified specification
Diagnosis sensor unit or front door satellite sen-
sor LH is different from the part specified
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-176
< DTC/CIRCUIT DIAGNOSIS >
B1350, B1351 SATELLITE SENSOR
B1350, B1351 SATELLITE SENSOR
DTC Logic
INFOID:0000000008461970
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-176, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008461971
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
REPLACE BOTH OF FRONT DOOR SATELLITE SENSOR
1.
Replace both of front door satellite sensor. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1350
B1351
FR DOOR SATEL SENS
Front door satellite sensor is malfunction-
ing or out of the specified specification
• Malfunction in front door satellite sensor LH/RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2012 October
2013 Murano CrossCabriolet
SRS AIR BAG WARNING LAMP DOES NOT TURN OFF
SRC-177
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
SYMPTOM DIAGNOSIS
SRS AIR BAG WARNING LAMP DOES NOT TURN OFF
Diagnosis Procedure
INFOID:0000000008461972
1.
CHECK AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
Check the deployment of air bag module and seat belt pre-tensioner.
Is air bag module deployed?
YES
>> Replace the malfunctioning parts.
NO
>> GO TO 2.
2.
CHECK AIR BAG FUSE
Check 10 A fuse [No.2, located in fuse block (J/B)].
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the fuse.
3.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace harness connectors.
4.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace wiring harness.
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Check air bag warning lamp operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 6.
6.
REPLACE COMBINATION METER
1.
Replace combination meter. Refer to
.
2.
Check air bag warning lamp operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 1.
Revision: 2012 October
2013 Murano CrossCabriolet
SRC-178
< SYMPTOM DIAGNOSIS >
SRS AIR BAG WARNING LAMP DOES NOT TURN ON
SRS AIR BAG WARNING LAMP DOES NOT TURN ON
Diagnosis Procedure
INFOID:0000000008461973
1.
CHECK COMBINATION METER POWER SUPPLY AND GROUND CIRCUIT
Check conbination meter unit power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace harness connectors.
3.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace wiring harness.
4.
CHECK AIR BAG DIAGNOSIS SENSOR UNIT
Disconnect air bag diagnosis sensor unit connector and turn ignition switch ON.
Does air bag warning lamp turn ON?
YES
>> Replace air bag diagnosis sensor unit. Refer to
NO
>> Replace combination meter. Refer to
MWI-70, "Removal and Installation"
Revision: 2012 October
2013 Murano CrossCabriolet
SRS AIR BAG WARNING LAMP BLINKS
SRC-179
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
SRS AIR BAG WARNING LAMP BLINKS
Diagnosis Procedure
INFOID:0000000008461974
1.
CHECK BATTERY
Check battery. Refer to
PG-101, "How to Handle Battery"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning parts.
2.
REPLACE OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT
1.
Replace occupant classification system control unit. Refer to
SR-33, "Removal and Installation"
.
2.
Check air bag warning lamp operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 3.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Check air bag warning lamp operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 1.
Revision: 2012 October
2013 Murano CrossCabriolet
ST-1
STEERING
C
D
E
F
H
I
J
K
L
M
SECTION
ST
A
B
ST
N
O
P
CONTENTS
STEERING SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Battery Service . . . . . . . . ..
Service Notice or Precautions for Steering System
. ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ....
Commercial Service Tools . . . . . . . . . ....
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location (Heated Steering
Wheel) . . . . . . . . . . . . . . . . . ...
Component Description (Heated Steering Wheel)
. ..
Heated Steering Wheel . . . . . . . . . . .....
Heated Steering Wheel Switch . . . . . . . .....
Heated Steering Wheel Relay . . . . . . . . ...
SYSTEM . . . . . . . . . . . . . . . ..
System Description (Heated Steering Wheel) . . ...
WIRING DIAGRAM . . . . . . . . . ...
HEATED STEERING WHEEL . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . .....
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORK FLOW . .
WorkFlow (Heated Steering Wheel) . . . . . .
STEERING WHEEL . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
DTC/CIRCUIT DIAGNOSIS . . . . . . .
HEATED STEERING WHEEL SYSTEM . . ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection (Heated Steering Wheel) .
Component Inspection (Heated Steering Wheel
Relay) . . . . . . . . . . . . . . . . . ..
HEATED STEERING WHEEL SWITCH INDI-
CATOR LAMP . . . . . . . . . . . . ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection (Heated Steering Wheel
Relay) . . . . . . . . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ..
HEATED STEERING WHEEL SYSTEM DOES
NOT ACTIVATE . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
HEATED STEERING WHEEL SWITCH INDI-
CATOR LAMP DOES NOT TURN ON . . . ..
Description . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . ...
NVH Troubleshooting Chart . . . . . . . . .
PERIODIC MAINTENANCE . . . . . .
POWER STEERING FLUID . . . . . . . ..
Inspection . . . . . . . . . . . . . . . .
STEERING WHEEL . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
STEERING WHEEL . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Revision: 2012 October
2013 Murano CrossCabriolet
ST-2
Removal and Installation . . . . . . . . . ....
STEERING COLUMN . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
Inspection . . . . . . . . . . . . . . . ...
LOWER SHAFT . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
Inspection . . . . . . . . . . . . . . . ...
STEERING GEAR AND LINKAGE . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
Disassembly and Assembly . . . . . . . . ....
Inspection . . . . . . . . . . . . . . . ...
POWER STEERING OIL PUMP . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
Disassembly and Assembly . . . . . . . . ....
Inspection . . . . . . . . . . . . . . . ...
HYDRAULIC LINE . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . . .
HEATED STEERING WHEEL SWITCH . . .
Removal and Installation . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
General Specifications . . . . . . . . . . .
Steering Wheel Axial End Play and Play . . . .
Steering Wheel Turning Force . . . . . . . .
Steering Angle . . . . . . . . . . . . . .
Steering Column Length . . . . . . . . . . .
Steering Column Mounting Dimensions . . . . ..
Steering Column Operating Range . . . . . . .
Lower Shaft Length . . . . . . . . . . . . .
Rack Sliding Force . . . . . . . . . . . . ..
Rack Stroke . . . . . . . . . . . . . . .
Socket Swing Force and Rotating Torque . . . ..
Socket Axial End Play . . . . . . . . . . . .
Inner Socket Length . . . . . . . . . . . .
Relief Oil Pressure . . . . . . . . . . . . ..
Revision: 2012 October
2013 Murano CrossCabriolet
PRECAUTIONS
ST-3
< PRECAUTION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000008461702
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Battery Service
INFOID:0000000008461703
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Service Notice or Precautions for Steering System
INFOID:0000000008461704
• In case of removing steering gear assembly, make the final tightening with grounded and unloaded vehicle
condition, and then check wheel alignment.
• Observe the following precautions when disassembling.
- Before disassembly, thoroughly clean the outside of the unit.
- Disassembly should be done in a clean work area. It is important to prevent the internal parts from becoming
contaminated by dirt or other foreign matter.
- For easier and proper assembly, place disassembled parts in order on a parts rack.
- Use nylon cloth or paper towels to clean the parts; common shop rags can leave lint that might interfere with
their operation.
- Never reuse non-reusable parts.
- Before assembling, apply the specified grease to the directed parts.
Revision: 2012 October
2013 Murano CrossCabriolet
ST-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000008461705
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
ST27180001
(J-25726-A)
Steering wheel puller
Removing steering wheel
ST3127S000
(J-25765-A)
Preload gauge
• Measuring steering wheel turning torque
• Measuring steering column rotating torque
• Measuring ball joint rotating torque
• Measuring pinion rotating torque
KV48104400
(
—
)
Teflon ring correcting tool
a: 50 mm (1.97 in) dia.
b: 36 mm (1.42 in) dia.
c: 100 mm (3.94 in)
Installing rack Teflon ring
KV48103400
(
—
)
Preload adapter
Measuring rotating torque
ST35300000
(
—
)
Drift
a: 45.1 mm (1.776 in) dia.
b: 59.0 mm (2.323 in) dia.
Installing oil pump oil seal
ZZA0819D
ZZA0806D
S-NT550
ZZA0824D
ZZA0881D
Revision: 2012 October
2013 Murano CrossCabriolet
PREPARATION
ST-5
< PREPARATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
Commercial Service Tools
INFOID:0000000008461706
KV48103500
(J-26357)
Oil pressure gauge
Measuring oil pump relief pressure
KV48102500
(J-33914)
Oil pressure gauge adapter
Measuring oil pump relief pressure
Tool number
(Kent-Moore No.)
Tool name
Description
S-NT547
S-NT542
Tool name
Description
Power tool
Loosening bolts and nuts
Ball joint remover
Removing steering outer socket
Open head
Tightening end cover assembly
PBIC0190E
S-NT146
ZZA0822D
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст