Murano Cross Cabriolet Z51 (2013 year). Manual — part 50
HAC-80
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
AMBIENT SENSOR
AMBIENT SENSOR
Exploded View
INFOID:0000000008460697
Removal and Installation
INFOID:0000000008460698
REMOVAL
Disconnect ambient sensor harness connector (A), and then remove
ambient sensor (1).
INSTALLATION
Install in the reverse order of removal.
1.
Ambient sensor
JPIIA1300ZZ
JPIIA0556ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
IN-VEHICLE SENSOR
HAC-81
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
IN-VEHICLE SENSOR
Exploded View
INFOID:0000000008460699
Removal and Installation
INFOID:0000000008460700
REMOVAL
1.
Remove instrument lower panel LH. Refer to
IP-13, "Removal and Installation"
2.
Remove fixing screw (A), and then remove in-vehicle sensor (1).
INSTALLATION
Install in the reverse order of removal.
1.
In-vehicle sensor
2.
Instrument lower panel LH
JPIIA0557ZZ
JPIIA0558ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
HAC-82
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
SUNLOAD SENSOR
SUNLOAD SENSOR
Exploded View
INFOID:0000000008460701
Removal and Installation
INFOID:0000000008460702
REMOVAL
Disconnect sunload sensor harness connector, and then remove
sunload sensor (1).
INSTALLATION
Install in the reverse order of removal.
1.
Sunload sensor
JPIIA0559ZZ
JPIIA0560ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
INTAKE SENSOR
HAC-83
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
INTAKE SENSOR
Exploded View
INFOID:0000000008460703
Removal and Installation
INFOID:0000000008460704
REMOVAL
1.
Remove evaporator pipe assembly. Refer to
HA-48, "EVAPORATOR PIPE ASSEMBLY : Removal and
.
2.
Pull out evaporator (1) toward the right side of vehicle, and then
remove intake sensor (2).
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply the compressor oil to them when installing.
• Mark the mounting position of intake sensor bracket prior to removal so that the reinstalled sensor
can be located in the same position.
• Never rotate the bracket insertion part when removing and installing the intake sensor.
1.
Heater & cooling unit assembly
2.
Intake sensor bracket
3.
Intake sensor
4.
Evaporator assembly
5.
Evaporator cover
6.
Air mix door motor (Passenger side)
7.
Foot duct RH
8.
Cooler pipe grommet
JPIIA1303ZZ
JPIIA0907ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
HAC-84
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
INTAKE SENSOR
• Check for leakages when recharging refrigerant. Refer to
Revision: 2012 October
2013 Murano CrossCabriolet
REFRIGERANT PRESSURE SENSOR
HAC-85
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
REFRIGERANT PRESSURE SENSOR
Exploded View
INFOID:0000000008460705
.
Removal and Installation
INFOID:0000000008460706
REMOVAL
HA-41, "REFRIGERANT PRESSURE SENSOR : Removal and Installation"
.
INSTALLATION
Install in the reverse order of removal.
Revision: 2012 October
2013 Murano CrossCabriolet
HAC-86
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
DOOR MOTOR
DOOR MOTOR
Exploded View
INFOID:0000000008460707
AIR MIX DOOR MOTOR
AIR MIX DOOR MOTOR : Removal and Installation
INFOID:0000000008460708
REMOVAL
Driver Side
1.
Set the temperature at full cold.
CAUTION:
The angle may be out, when installing the air mix door motor to the air mix door, unless the above
procedure is performed.
2.
Disconnect the battery cable from the negative terminal.
3.
Remove front foot duct LH. Refer to
VTL-12, "FRONT FOOT DUCT : Removal and Installation"
.
4.
Disconnect air mix door motor harness connector.
1.
Intake door motor
2.
Blower unit assembly
3.
Mode door motor
4.
Main link
5.
Link rod
6.
Foot door link
7.
Max. cool door link
8.
Mode door lever
9.
Ventilator door link
10. Defroster door link
11.
Ventilator door lever
12. Foot door lever
13. Max. cool door lever
14.
Defroster door lever
15. Air mix door motor (Driver side)
16. Heater & cooling unit assembly
17.
Air mix door motor (Passenger side) 18. Upper ventilator door motor
19. Upper ventilator door rod
20.
Upper ventilator door lever
: Vehicle front
JPIIA1238ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
DOOR MOTOR
HAC-87
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
5.
Remove fixing screws (A), and then air mix door motor (1).
Passenger Side
1.
Set the temperature at full cold.
CAUTION:
The angle may be out, when installing the air mix door motor to the air mix door, unless the above
procedure is performed.
2.
Disconnect the battery cable from the negative terminal.
3.
Remove front foot duct RH. Refer to
VTL-12, "FRONT FOOT DUCT : Removal and Installation"
4.
Disconnect air mix door motor harness connector.
5.
Remove fixing screws (A), and then air mix door motor (1).
INSTALLATION
Install in the reverse order of removal.
MODE DOOR MOTOR
MODE DOOR MOTOR : Removal and Installation
INFOID:0000000008460709
REMOVAL
1.
Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2.
Disconnect mode door motor harness connector.
3.
Remove fixing screws (A), and then remove mode door motor
(1).
INSTALLATION
Install in the reverse order of removal.
INTAKE DOOR MOTOR
JPIIA0577ZZ
JPIIA0578ZZ
JPIIA0575ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
HAC-88
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
DOOR MOTOR
INTAKE DOOR MOTOR : Removal and Installation
INFOID:0000000008460710
REMOVAL
1.
Remove instrument lower panel RH. Refer to
IP-13, "Removal and Installation"
2.
Remove fixing screw (A), and then move key less controller
assembly bracket (1) to secure work space.
3.
Disconnect intake door motor harness connector.
4.
Remove fixing screws (A), and then remove intake door motor
(1).
INSTALLATION
Install in the reverse order of removal.
UPPER VENTILATOR DOOR MOTOR
UPPER VENTILATOR DOOR MOTOR : Removal and Installation
INFOID:0000000008460711
REMOVAL
1.
Remove blower unit assmbly. Refer to
VTL-19, "Removal and Installation"
2.
Disconnect upper ventilator door motor harness connector.
3.
Remove fixing screws (A), and then remove upper ventilator
door motor (1).
INSTALLATION
Install in the reverse order of removal.
JPIIA0569ZZ
JPIIA0570ZZ
JPIIA0574ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
HRN-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
HRN
A
B
HRN
N
O
P
CONTENTS
HORN
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
WIRING DIAGRAM . . . . . . . . . ...
HORN . . . . . . . . . . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . .
HORN . . . . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Revision: 2012 October
2013 Murano CrossCabriolet
HRN-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000008462239
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Revision: 2012 October
2013 Murano CrossCabriolet
HORN
HRN-3
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
M
A
B
HRN
N
O
P
WIRING DIAGRAM
HORN
Wiring Diagram
INFOID:0000000008462240
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JCLWA5340GB
Revision: 2012 October
2013 Murano CrossCabriolet
HRN-4
< REMOVAL AND INSTALLATION >
HORN
REMOVAL AND INSTALLATION
HORN
Exploded View
INFOID:0000000008462241
Removal and Installation
INFOID:0000000008462242
REMOVAL
1.
Remove the front grille. Refer to
2.
Disconnect the horn (LOW, HIGH) connector.
3.
Remove the horn mounting nut, and remove the horn (LOW, HIGH) from the vehicle.
INSTALLATION
Install in the reverse order of removal.
1.
Horn (HIGH)
2.
Horn (LOW)
JPLIA1492ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
INL-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
INL
A
B
INL
N
O
P
CONTENTS
INTERIOR LIGHTING SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Battery Service . . . . . . . . ..
Service Procedure Precautions for Models with a
Pop-up Roll Bar . . . . . . . . . . . . . .....
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
INTERIOR LIGHTING SYSTEM . . . . . . . . ..
INTERIOR LIGHTING SYSTEM : Component
Parts Location . . . . . . . . . . . . . . ...
INTERIOR LIGHTING SYSTEM :
Component Description . . . . . . . . . . ....
SYSTEM . . . . . . . . . . . . . . . ..
INTERIOR ROOM LAMP CONTROL SYSTEM . . ..
INTERIOR ROOM LAMP CONTROL SYSTEM :
System Diagram . . . . . . . . . . . . . ....
INTERIOR ROOM LAMP CONTROL SYSTEM :
System Description . . . . . . . . . . . . ...
INTERIOR ROOM LAMP BATTERY SAVER SYS-
TEM . . . . . . . . . . . . . . . . . . . ..
INTERIOR ROOM LAMP BATTERY SAVER
SYSTEM : System Diagram . . . . . . . . . ..
INTERIOR ROOM LAMP BATTERY SAVER
SYSTEM : System Description . . . . . . . .....
ILLUMINATION CONTROL SYSTEM . . . . . .....
ILLUMINATION CONTROL SYSTEM : System
Diagram . . . . . . . . . . . . . . . . .....
ILLUMINATION CONTROL SYSTEM : System
Description . . . . . . . . . . . . . . . ....
DIAGNOSIS SYSTEM (BCM) . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
INT LAMP . . . . . . . . . . . . . . . . ...
INT LAMP : CONSULT Function (BCM - INT
LAMP) . . . . . . . . . . . . . . . . . ..
BATTERY SAVER . . . . . . . . . . . . . .
BATTERY SAVER : CONSULT Function (BCM -
BATTERY SAVER) . . . . . . . . . . . . ..
ECU DIAGNOSIS INFORMATION . . . ..
BCM . . . . . . . . . . . . . . . . ...
List of ECU Reference . . . . . . . . . . . .
WIRING DIAGRAM . . . . . . . . . ..
INTERIOR ROOM LAMP CONTROL SYSTEM
...
Wiring Diagram . . . . . . . . . . . . . .
ILLUMINATION . . . . . . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . .
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORKFLOW . .
Work Flow . . . . . . . . . . . . . . . .
DTC/CIRCUIT DIAGNOSIS . . . . . . .
INTERIOR ROOM LAMP POWER SUPPLY
CIRCUIT . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
INTERIOR ROOM LAMP CONTROL CIRCUIT
...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
Revision: 2012 October
2013 Murano CrossCabriolet
INL-2
TRUNK ROOM LAMP CIRCUIT . . . . . .
Diagnosis Procedure . . . . . . . . . . . ..
STEP LAMP CIRCUIT . . . . . . . . . ...
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
PUSH-BUTTON IGNITION SWITCH ILLUMI-
NATION CIRCUIT . . . . . . . . . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . .
INTERIOR LIGHTING SYSTEM SYMPTOMS ...
Symptom Table . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . ...
MAP LAMP . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
Replacement . . . . . . . . . . . . . . ..
VANITY MIRROR LAMP . . . . . . . . ...
Exploded View . . . . . . . . . . . . . ....
Replacement . . . . . . . . . . . . . . ..
GLOVE BOX LAMP . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . ...
CONSOLE POCKET LAMP . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . ...
STEP LAMP . . . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . ...
TRUNK ROOM LAMP . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . ...
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Bulb Specifications . . . . . . . . . . . . ..
Revision: 2012 October
2013 Murano CrossCabriolet
PRECAUTIONS
INL-3
< PRECAUTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000008460357
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Battery Service
INFOID:0000000008460358
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Service Procedure Precautions for Models with a Pop-up Roll Bar
INFOID:0000000008460359
WARNING:
Always observe the following items for preventing accidental activation.
• Risk of passenger injury or death may increase if the pop-up roll bar does not deploy during a roll
over collision. In order to reduce the chance of an incident where the pop-up roll bar is inoperative,
all maintenance must be performed by a NISSAN or INFINITI dealer.
• Before removing and installing the pop-up roll bar component parts and harness, always turn the
ignition switch OFF, disconnect the battery negative terminal, and wait for 3 minutes or more. (The
purpose of this operation is to discharge electricity that is accumulated in the auxiliary power supply
circuit in the air bag diagnosis sensor unit.)
• When repairing, removing, and installing a pop-up roll bar, always refer to SRS AIR BAG and SRS
AIR BAG CONTROL warnings in the Service Manual.
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст