Murano Cross Cabriolet Z51 (2013 year). Manual — part 49
HAC-64
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
POWER SUPPLY AND GROUND CIRCUIT
5.
CHECK FUSE
1.
Turn ignition switch OFF.
2.
Check 10A fuse (No. 6, located in fuse block (J/B)].
NOTE:
Refer to
PG-33, "Fuse, Connector and Terminal Arrangement"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
6.
CHECK A/C AUTO AMP. BATTERY POWER SUPPLY
1.
Disconnect A/C auto amp. connector.
2.
Check voltage between A/C auto amp. harness connector and ground.
Is the inspection result normal?
YES
>> Replace A/C auto amp. Refer to
HAC-79, "Removal and Installation"
NO
>> Repair harness or connector between A/C auto amp. and fuse.
+
−
Voltage
A/C auto amp.
Connector
Terminal
M50
40
Ground
Battery voltage
Revision: 2012 October
2013 Murano CrossCabriolet
DOOR MOTOR
HAC-65
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
DOOR MOTOR
Diagnosis Procedure
INFOID:0000000008460680
NOTE:
Check this circuit when all of door motors DTC (B2632, B2633, B2634, B2635, B2636, B2637, B2638, B2639,
B263D, B263E, B263F, B2654, B2655, B2661, B2662, and B2663) are detected.
1.
CHECK DOOR MOTOR POWER SUPPLY
1.
Turn ignition switch ON.
2.
Check voltage between intake door motor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 7.
2.
CHECK DOOR MOTOR GROUND CIRCUIT FOR OPEN
1.
Turn ignition switch OFF.
2.
Disconnect intake door motor and A/C auto amp. connector.
3.
Check continuity between intake door motor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK DOOR MOTOR LAN SIGNAL
1.
Connect A/C auto amp. and intake door motor connector.
2.
Turn ignition switch ON.
3.
Confirm output waveform between A/C auto amp. harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 6.
4.
CHECK DOOR MOTOR LAN SIGNAL CIRCUIT FOR OPEN
1.
Turn ignition switch OFF.
2.
Disconnect A/C auto amp. and intake door motor connector.
+
−
Voltage
(Approx.)
Intake door motor
Connector
Terminal
M304
1
Ground
12 V
Intake door motor
—
Continuity
Connector
Terminal
M304
2
Ground
Existed
+
−
Output waveform
A/C auto amp.
Connector
Terminal
M50
5
Ground
SJIA1453J
Revision: 2012 October
2013 Murano CrossCabriolet
HAC-66
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
DOOR MOTOR
3.
Check continuity between A/C auto amp. harness connector and intake door motor harness connector.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair harness or connector.
5.
CHECK INTERMITTENT INCIDENT
Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
>> INSPECTION END
6.
CHECK DOOR MOTOR LAN SIGNAL CIRCUIT FOR SHORT
1.
Turn ignition switch OFF.
2.
Disconnect following connectors.
-
A/C auto amp.
-
Air mix door motor LH
-
Air mix door motor RH
-
Mode door motor
-
Intake door motor
3.
Check continuity between A/C auto amp. harness connector and ground.
Is the inspection result normal?
YES
>> Replace A/C auto amp. Refer to
HAC-79, "Removal and Installation"
NO
>> Repair harness or connector.
7.
CHECK DOOR MOTOR POWER SUPPLY CIRCUIT FOR OPEN
1.
Turn ignition switch OFF.
2.
Disconnect intake door motor and A/C auto amp. connector.
3.
Check continuity between intake door motor harness connector and A/C auto amp. harness connector.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair harness or connector.
8.
CHECK DOOR MOTOR POWER SUPPLY CIRCUIT FOR SHORT
1.
Disconnect following connectors.
-
A/C auto amp.
-
Air mix door motor LH
-
Air mix door motor RH
-
Mode door motor
2.
Check continuity between A/C auto amp. harness connector and ground.
A/C auto amp.
Intake door motor
Continuity
Connector
Terminal
Connector
Terminal
M50
10
M304
3
Existed
A/C auto amp.
—
Continuity
Connector
Terminal
M50
10
Ground
Not existed
Intake door motor
A/C auto amp.
Continuity
Connector
Terminal
Connector
Terminal
M304
1
M50
11
Existed
A/C auto amp.
—
Continuity
Connector
Terminal
M50
11
Ground
Not existed
Revision: 2012 October
2013 Murano CrossCabriolet
DOOR MOTOR
HAC-67
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
Is the inspection result normal?
YES
>> Replace A/C auto amp. Refer to
HAC-79, "Removal and Installation"
NO
>> Repair harness or connector.
Revision: 2012 October
2013 Murano CrossCabriolet
HAC-68
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
BLOWER MOTOR
BLOWER MOTOR
Diagnosis Procedure
INFOID:0000000008460681
1.
CHECK FUSE
1.
Turn ignition switch OFF.
2.
Check 15A fuse [No. 21 and 22, located in fuse block (J/B)].
NOTE:
Refer to
PG-33, "Fuse, Connector and Terminal Arrangement"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
2.
CHECK BLOWER MOTOR POWER SUPPLY
1.
Disconnect blower motor connector.
2.
Turn ignition switch ON.
3.
Check voltage between blower motor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 6.
3.
CHECK BLOWER MOTOR GROUND CIRCUIT FOR OPEN
1.
Turn ignition switch OFF.
2.
Check continuity between blower motor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK BLOWER MOTOR CONTROL SIGNAL CIRCUIT FOR OPEN
1.
Disconnect A/C auto amp. connector.
2.
Check continuity between blower motor harness connector and A/C auto amp. harness connector.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair harness or connector.
5.
CHECK BLOWER MOTOR CONTROL SIGNAL
1.
Reconnect blower motor connector and A/C auto amp. connector.
2.
Turn ignition switch ON.
3.
Operate MODE switch to set air outlet to VENT position.
4.
Change fan speed from Lo to Hi, and check duty ratios between blower motor harness connector and
ground by using an oscilloscope.
+
−
Voltage
Blower motor
Connector
Terminal
M98
1
Ground
Battery voltage
Blower motor
—
Continuity
Connector
Terminal
M98
3
Ground
Existed
Blower motor
A/C auto amp.
Continuity
Connector
Terminal
Connector
Terminal
M98
2
M50
32
Existed
Revision: 2012 October
2013 Murano CrossCabriolet
BLOWER MOTOR
HAC-69
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
NOTE:
Calculate drive signal duty ratio as shown in the figure.
T2 = Approx. 1.6 ms
Is the inspection result normal?
YES
>> Replace blower motor. Refer to
VTL-21, "Removal and Installation"
.
NO
>> Replace A/C auto amp. Refer to
HAC-79, "Removal and Installation"
6.
CHECK BLOWER MOTOR POWER SUPPLY CIRCUIT FOR OPEN
1.
Turn ignition switch OFF.
2.
Disconnect fuse block (J/B) connector.
3.
Check continuity between fuse block (J/B) harness connector and blower motor harness connector.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair harness or connector.
7.
CHECK BLOWER RELAY GROUND CIRCUIT FOR OPEN
Check continuity between fuse block (J/B) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair harness or connector.
8.
CHECK BLOWER RELAY
Check blower relay. Refer to
HAC-70, "Component Inspection (Blower Relay)"
Is the inspection result normal?
YES
>> Check blower relay power supply circuit. Refer to
PG-11, "Wiring Diagram - BATTERY POWER
PG-27, "Wiring Diagram - IGNITION POWER SUPPLY -"
NO
>> Replace blower relay.
Component Inspection (Blower Motor)
INFOID:0000000008460682
1.
CHECK BLOWER MOTOR-I
1.
Remove blower motor. Refer to
VTL-21, "Removal and Installation"
Blower motor
Condition
Duty ratio
(Approx.)
Connector
Terminal
Fan speed (manual)
VENT mode
M98
2
1st
25 %
2nd
33 %
3rd
41 %
4th
51 %
5th
61 %
6th
69 %
7th
81 %
JPLIA1210GB
Fuse block (J/B)
Blower motor
Continuity
Connector
Terminal
Connector
Terminal
M1
3A
M98
3
Existed
8A
Fuse block (J/B)
—
Continuity
Connector
Terminal
M3
7C
Ground
Existed
Revision: 2012 October
2013 Murano CrossCabriolet
HAC-70
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
BLOWER MOTOR
2.
Check that there is not any mixing foreign object in the blower motor.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace blower motor. Refer to
VTL-21, "Removal and Installation"
.
2.
CHECK BLOWER MOTOR-II
Check that there is not breakage or damage in the blower motor.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace blower motor. Refer to
VTL-21, "Removal and Installation"
.
3.
CHECK BLOWER MOTOR-III
Check that blower motor turns smoothly.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace blower motor. Refer to
VTL-21, "Removal and Installation"
.
Component Inspection (Blower Relay)
INFOID:0000000008460683
1.
CHECK BLOWER RELAY
1.
Remove blower relay. Refer to
PG-33, "Fuse, Connector and Terminal Arrangement"
2.
Check continuity between blower relay terminal 3 and 5 when
voltage is supplied between terminal 1 and 2.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace blower relay.
Terminal
Voltage
Continuity
3
5
ON
Existed
OFF
Not existed
JSIIA1551ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
MAGNET CLUTCH
HAC-71
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
MAGNET CLUTCH
Component Function Check
INFOID:0000000008460684
1.
CHECK MAGNET CLUTCH OPERATION
Perform auto active test of IPDM E/R. Refer to
PCS-10, "Diagnosis Description"
.
Does it operate normally?
YES
>> INSPECTION END
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000008460685
1.
CHECK MAGNET CLUTCH
1.
Turn ignition switch OFF.
2.
Disconnect compressor connector.
3.
Directly apply battery voltage to the magnet clutch. Check for operation visually and by sound.
Does it operate normally?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK FUSE
Check 10A fuse (No. 49, located in IPDM E/R).
NOTE:
Refer to
PG-35, "Fuse, Connector and Terminal Arrangement"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
3.
CHECK MAGNET CLUTCH POWER SUPPLY CIRCUIT FOR OPEN
1.
Disconnect IPDM E/R connector.
2.
Check continuity between IPDM E/R harness connector and compressor harness connector.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
NO
>> Repair harness or connector.
4.
CHECK MAGNET CLUTCH GROUND CIRCUIT FOR OPEN
Check continuity between compressor harness connector and ground.
Is the inspection result normal?
YES
>> Replace magnet clutch. Refer to
HA-31, "MAGNET CLUTCH : Removal and Installation of Com-
NO
>> Repair harness or connector.
IPDM E/R
Compressor
Continuity
Connector
Terminal
Connector
Terminal
F12
48
F18
1
Existed
Compressor
—
Continuity
Connector
Terminal
F18
2
Ground
Existed
Revision: 2012 October
2013 Murano CrossCabriolet
HAC-72
< SYMPTOM DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
AUTOMATIC AIR CONDITIONING SYSTEM
SYMPTOM DIAGNOSIS
AUTOMATIC AIR CONDITIONING SYSTEM
Symptom Table
INFOID:0000000008460686
NOTE:
Perform self-diagnoses with CONSULT before performing the symptom diagnosis. If any DTC is detected,
perform the corresponding diagnosis.
Symptom
Corresponding malfunction part
Check item/Reference
• Air conditioning does not ac-
tivate.
• Air conditioning cannot be
controlled.
• Operation status of air condi-
tioning is not indicated on
display.
Fail-safe activates
Multi AV system
• BOSE audio without naviga-
tion:
• BOSE audio with navigation:
Fail-safe does not acti-
vate
• A/C auto amp. ignition power supply
circuit and ACC power supply circuit
• A/C auto amp.
HAC-63, "A/C AUTO AMP. : Di-
agnosis Procedure"
• Memory function does not operate normally.
• The setting is not maintained. (It returns to initial condi-
tion)
• A/C auto amp. battery power supply
circuit
• A/C auto amp.
HAC-63, "A/C AUTO AMP. : Di-
agnosis Procedure"
Discharge air temperature (driver side) does not change.
Air mix door motor (driver side) system
installation condition
Check air mix door motor (driver
side) system is properly in-
stalled. Refer to
Discharge air temperature (passenger side) does not
change.
Air mix door motor (passenger side)
system installation condition
Check air mix door motor (pas-
senger side) system is properly
installed. Refer to
Air outlet does not change.
Mode door motor system installation
condition
Check mode door motor system
is properly installed. Refer to
.
Air inlet does not change.
Intake door motor system installation
condition
Check intake door motor system
is properly installed. Refer to
.
Blower motor does not operate.
• Blower motor power supply circuit.
• Blower motor control signal circuit
• Blower motor
• A/C auto amp.
Compressor does not operate.
• Magnet clutch
• The circuit between magnet clutch
and IPDM E/R
• IPDM E/R (A/C relay)
• The circuit between ECM and refrig-
erant pressure sensor
• Refrigerant pressure sensor
• A/C auto amp. output signal (A/C
ON signal and blower fan ON signal)
• A/C auto amp.
• Insufficient cooling
• No cool air comes out. (Air flow volume is normal.)
• Magnet clutch control system
• Drive belt slipping
• Cooler cycle
• Air leakage from each duct
• A/C auto amp. connection recogni-
tion signal circuit
• Temperature setting trimmer
Revision: 2012 October
2013 Murano CrossCabriolet
AUTOMATIC AIR CONDITIONING SYSTEM
HAC-73
< SYMPTOM DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
• Insufficient heating
• No warm air comes out. (Air flow volume is normal.)
• Engine cooling system
• Heater hose
• Heater core
• Air leakage from each duct
• Temperature setting trimmer
Noise is heard when the air
conditioning operates.
During compressor op-
eration
Cooler cycle
During blower motor op-
eration
• Mixing any foreign object in blower
motor
• Blower motor fan breakage
• Blower motor rotation inferiority
HAC-69, "Component Inspec-
tion (Blower Motor)"
Symptom
Corresponding malfunction part
Check item/Reference
Revision: 2012 October
2013 Murano CrossCabriolet
HAC-74
< SYMPTOM DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
INSUFFICIENT COOLING
INSUFFICIENT COOLING
Description
INFOID:0000000008460687
Symptom
• Insufficient cooling
• No cool air comes out. (Air flow volume is normal.)
Diagnosis Procedure
INFOID:0000000008460688
NOTE:
Perform self-diagnoses with CONSULT before performing symptom diagnosis. If any DTC is detected, per-
form the corresponding diagnosis.
1.
CHECK MAGNET CLUTCH OPERATION
1.
Turn ignition switch ON.
2.
Operate fan control dial.
3.
Press A/C switch.
4.
Check that A/C indicator turns ON. Check visually and by sound that compressor operates.
5.
Press A/C switch again.
6.
Check that A/C indicator turns OFF. Check that compressor stops.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform diagnosis of “COMPRESSOR DOES NOT OPERATE” in “SYMPTOM DIAGNOSIS”.
2.
CHECK DRIVE BELT
Check tension of drive belt. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Adjust or replace drive belt depending on the inspection results.
3.
CHECK REFRIGERANT CYCLE PRESSURE
Connect recovery/recycling recharging equipment to the vehicle and perform pressure inspection with gauge.
Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace parts depending on the inspection results.
4.
CHECK AIR LEAKAGE FROM EACH DUCT
Check duct and nozzle, etc. of the air conditioning system for leakage.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace parts depending on the inspection results.
5.
CHECK AMBIENT TEMPERATURE DISPLAY
Check that there is not much difference between actual ambient temperature and indicated temperature on
information display in combination meter.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Perform diagnosis for the A/C auto amp. connection recognition signal circuit. Refer to
6.
CHECK SETTING OF TEMPERATURE SETTING TRIMMER
1.
Check setting value of temperature setting trimmer. Refer to
HAC-35, "Temperature Setting Trimmer"
.
2.
Check that temperature setting trimmer is set to “+ direction”.
NOTE:
The control temperature can be set by setting of the temperature setting trimmer.
Revision: 2012 October
2013 Murano CrossCabriolet
INSUFFICIENT COOLING
HAC-75
< SYMPTOM DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
3.
Set difference between the set temperature and control temperature to “0”.
Is inspection result normal?
YES
>> INSPECTION END
NO
>> Replace A/C auto amp. Refer to
HAC-79, "Removal and Installation"
Revision: 2012 October
2013 Murano CrossCabriolet
HAC-76
< SYMPTOM DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
INSUFFICIENT HEATING
INSUFFICIENT HEATING
Description
INFOID:0000000008460689
Symptom
• Insufficient heating
• No warm air comes out. (Air flow volume is normal.)
Diagnosis Procedure
INFOID:0000000008460690
NOTE:
Perform self-diagnoses with CONSULT before performing symptom diagnosis. If any DTC is detected, per-
form the corresponding diagnosis.
1.
CHECK COOLING SYSTEM
1.
Check engine coolant level and check for leakage. Refer to
2.
Check radiator cap. Refer to the
CO-12, "RADIATOR CAP : Inspection"
.
3.
Check water flow sounds of the engine coolant. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refill engine coolant and repair or replace the parts depending on the inspection results.
2.
CHECK HEATER HOSE
Check installation of heater hose by visually or touching.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace parts depending on the inspection results.
3.
CHECK HEATER CORE
1.
Check temperature of inlet hose and outlet hose of heater core.
2.
Check that inlet side of heater core is hot and the outlet side is slightly lower than/almost equal to the inlet
side.
CAUTION:
Always perform the temperature inspection in a short period of time because the engine coolant
temperature is very hot.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace heater core. Refer to
HA-49, "HEATER CORE : Removal and Installation"
.
4.
CHECK AIR LEAKAGE FROM EACH DUCT
Check duct and nozzle, etc. of the air conditioning for air leakage.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace parts depending on the inspection results.
5.
CHECK SETTING OF TEMPERATURE SETTING TRIMMER
1.
Check setting value of temperature setting trimmer. Refer to
HAC-35, "Temperature Setting Trimmer"
.
2.
Check that temperature setting trimmer is set to “
−
direction”.
NOTE:
The control temperature can be set by the temperature setting trimmer.
3.
Set difference between the set temperature and control temperature to “0”.
Are the symptoms solved?
YES
>> INSPECTION END
NO
>> Replace A/C auto amp. Refer to
HAC-79, "Removal and Installation"
Revision: 2012 October
2013 Murano CrossCabriolet
COMPRESSOR DOES NOT OPERATE
HAC-77
< SYMPTOM DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
COMPRESSOR DOES NOT OPERATE
Description
INFOID:0000000008460691
SYMPTOM
Compressor does not operate.
Diagnosis Procedure
INFOID:0000000008460692
NOTE:
• Perform self-diagnoses with CONSULT before performing symptom diagnosis. If any DTC is detected, per-
form the corresponding diagnosis.
• Check that refrigerant is enclosed in cooler cycle normally. If refrigerant amount is shortage from proper
amount, perform the inspection of refrigerant leakage.
1.
CHECK MAGNET CLUTCH OPERATION
Check magnet clutch. Refer to
HAC-71, "Component Function Check"
.
Does it operate normally?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning parts.
2.
CHECK REFRIGERANT PRESSURE SENSOR
Check refrigerant pressure sensor. Refer to
EC-417, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK A/C AUTO AMP. OUTPUT SIGNAL
With CONSULT
1.
Select “DATA MONITOR” mode of “ECM” using CONSULT.
2.
Select “AIR COND SIG” and “HEATER FAN SW”, and check status under the following conditions.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
NO
>> Replace A/C auto amp. Refer to
HAC-79, "Removal and Installation"
Monitor item
Condition
Status
AIR COND SIG
A/C switch
OFF (A/C indicator: OFF)
Off
ON (A/C indicator: ON)
On
HEATER FAN SW
Blower motor
OFF
Off
ON
On
Revision: 2012 October
2013 Murano CrossCabriolet
HAC-78
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
PRESET SWITCH
REMOVAL AND INSTALLATION
PRESET SWITCH
Exploded View
INFOID:0000000008460693
DISASSEMBLY
Removal and Installation
INFOID:0000000008460694
REMOVAL
Remove preset switch. Refer to the following.
• Refer to
AV-112, "Removal and Installation"
. (BOSE AUDIO WITHOUT NAVIGATION)
• Refer to
AV-246, "Removal and Installation"
. (BOSE AUDIO WITH NAVIGATION)
INSTALLATION
Install in the reverse order of removal.
1.
Preset switch
2.
Cluster lid C
JPNIA0790ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
A/C AUTO AMP.
HAC-79
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
A/C AUTO AMP.
Exploded View
INFOID:0000000008460695
DISASSEMBLY
Removal and Installation
INFOID:0000000008460696
REMOVAL
1.
Remove AV control unit. Refe to the following.
• Refer to
AV-102, "Removal and Installation"
. (BOSE AUDIO WITHOUT NAVIGATION)
• Refer to
AV-236, "Removal and Installation"
. (BOSE AUDIO WITH NAVIGATION)
2.
Remove fixing screws (A), and then remove A/C auto amp. (1).
INSTALLATION
Install in the reverse order of removal.
JPIIA0553ZZ
1.
AV control unit
2.
Bracket LH
3.
A/C auto amp.
4.
Bracket RH
JPIIA0554ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст