Murano Cross Cabriolet Z51 (2013 year). Manual — part 72
POWER WINDOW RETAINED POWER OPERATION DOES NOT OPERATE
PROPERLY
PWC-61
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
POWER WINDOW RETAINED POWER OPERATION DOES NOT OPER-
ATE PROPERLY
Diagnosis Procedure
INFOID:0000000008463280
1.
CHECK FRONT DOOR SWITCH
Check front door switch.
Refer to
DLK-55, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-77, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2012 October
2013 Murano CrossCabriolet
PWC-62
< SYMPTOM DIAGNOSIS >
DOOR KEY CYLINDER SWITCH DOES NOT OPERATE POWER WINDOWS
DOOR KEY CYLINDER SWITCH DOES NOT OPERATE POWER WIN-
DOWS
Diagnosis Procedure
INFOID:0000000008463281
1.
PERFORM INITIALIZATION PROCEDURE
Initialization procedure is executed and operation is confirmed.
Refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK FRONT DOOR LOCK ASSEMBLY (DRIVER SIDE) (DOOR KEY CYLINDER SWITCH)
Check front door lock assembly (driver side) (door key cylinder switch).
Refer to
PWC-44, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE POWER WINDOW MAIN SWITCH
1.
Replace power window main switch. Refer to
PWC-66, "Removal and Installation"
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2012 October
2013 Murano CrossCabriolet
KEYLESS POWER WINDOW DOWN DOES NOT OPERATE
PWC-63
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
KEYLESS POWER WINDOW DOWN DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000008463282
1.
CHECK REMOTE KEYLESS ENTRY FUNCTION
Check remote keyless entry function.
Does door lock/unlock with Intelligent Key button?
YES
>> GO TO 2.
NO
>> Refer to
DLK-20, "REMOTE KEYLESS ENTRY FUNCTION : System Description"
2.
CHECK POWER WINDOW OPERATION
Check power window operation.
Does power window up/down with power window main switch?
YES
>> GO TO 3.
NO
>> Refer to
.
3.
CHECK “PW DOWN SET” SETTING IN “WORK SUPPORT”
Check “PW DOWN SET” setting in “WORK SUPPORT”.
Refer to
DLK-35, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set “PW DOWN SET” setting in “WORK SUPPORT”.
4.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-77, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2012 October
2013 Murano CrossCabriolet
PWC-64
< SYMPTOM DIAGNOSIS >
POWER WINDOW LOCK SWITCH DOES NOT FUNCTION
POWER WINDOW LOCK SWITCH DOES NOT FUNCTION
Diagnosis Procedure
INFOID:0000000008463283
1.
REPLACE POWER WINDOW MAIN SWITCH
Replace power window main switch.
Refer to
PWC-66, "Removal and Installation"
.
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
POWER WINDOW SWITCH ILLUMINATION DOES NOT ILLUMINATE
PWC-65
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
POWER WINDOW SWITCH ILLUMINATION DOES NOT ILLUMINATE
DRIVER SIDE
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000008463284
1.
REPLACE POWER WINDOW MAIN SWITCH
Replace power window main switch.
Refer to
PWC-66, "Removal and Installation"
.
>> INSPECTION END
PASSENGER SIDE
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000008463285
1.
REPLACE FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
Replace front power window switch (passenger side).
Refer to
PWC-66, "Removal and Installation"
.
>> INSPECTION END
REAR LH
REAR LH : Diagnosis Procedure
INFOID:0000000008463286
1.
REPLACE REAR POWER WINDOW SWITCH LH
Replace rear power window switch LH.
Refer to
PWC-66, "Removal and Installation"
.
>> INSPECTION END
REAR RH
REAR RH : Diagnosis Procedure
INFOID:0000000008463287
1.
REPLACE REAR POWER WINDOW SWITCH RH
Replace rear power window switch RH.
Refer to
PWC-66, "Removal and Installation"
.
>> INSPECTION END
Revision: 2012 October
2013 Murano CrossCabriolet
PWC-66
< REMOVAL AND INSTALLATION >
POWER WINDOW MAIN SWITCH
REMOVAL AND INSTALLATION
POWER WINDOW MAIN SWITCH
Exploded View
INFOID:0000000008463288
Removal and Installation
INFOID:0000000008463289
REMOVAL
1.
Remove the power window main switch finisher. Refer to
13, "Removal and Installation"
.
2.
Power window main switch (1) is removed from power window
main switch finisher (2) using remover tool (A).
NOTE:
The same procedure is also performed for front power window
switch (passenger side) and rear power window switch (LH & RH).
INSTALLATION
Install in the reverse order of removal.
NOTE:
If power window main switch or front power window switch (passenger side) is replaced or removed, it is nec-
essary to perform initialization procedure. Refer to
.
1.
Power window main switch
2.
Power window main switch finisher
JMKIA1823ZZ
JMKIA1822ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
PWO
PWO-1
ELECTRICAL & POWER CONTROL
C
D
E
F
G
H
I
J
K
L
B
SECTION
PWO
A
O
P
N
CONTENTS
POWER OUTLET
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Service Procedure Precautions for Models with a
Pop-up Roll Bar . . . . . . . . . . . . . .....
Precaution for Battery Service . . . . . . . . ..
WIRING DIAGRAM . . . . . . . . . ...
POWER SOCKET . . . . . . . . . . . ...
Wiring Diagram . . . . . . . . . . . . . .....
REMOVAL AND INSTALLATION . . . .
POWER SOCKET . . . . . . . . . . . ..
FRONT POWER SOCKET . . . . . . . . . . ..
FRONT POWER SOCKET : Exploded View . . ....
FRONT POWER SOCKET : Removal and Instal-
lation . . . . . . . . . . . . . . . . . . .
CONSOLE POWER SOCKET . . . . . . . . ....
CONSOLE POWER SOCKET : Exploded View . ...
CONSOLE POWER SOCKET : Removal and In-
stallation . . . . . . . . . . . . . . . . ...
Revision: 2012 October
2013 Murano CrossCabriolet
PWO-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000008462878
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Service Procedure Precautions for Models with a Pop-up Roll Bar
INFOID:0000000008462879
WARNING:
Always observe the following items for preventing accidental activation.
• Risk of passenger injury or death may increase if the pop-up roll bar does not deploy during a roll
over collision. In order to reduce the chance of an incident where the pop-up roll bar is inoperative,
all maintenance must be performed by a NISSAN or INFINITI dealer.
• Before removing and installing the pop-up roll bar component parts and harness, always turn the
ignition switch OFF, disconnect the battery negative terminal, and wait for 3 minutes or more. (The
purpose of this operation is to discharge electricity that is accumulated in the auxiliary power supply
circuit in the air bag diagnosis sensor unit.)
• When repairing, removing, and installing a pop-up roll bar, always refer to SRS AIR BAG and SRS
AIR BAG CONTROL warnings in the Service Manual.
Precaution for Battery Service
INFOID:0000000008462880
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Revision: 2012 October
2013 Murano CrossCabriolet
PWO
POWER SOCKET
PWO-3
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
WIRING DIAGRAM
POWER SOCKET
Wiring Diagram
INFOID:0000000008462881
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JRMWC5439GB
Revision: 2012 October
2013 Murano CrossCabriolet
PWO-4
< REMOVAL AND INSTALLATION >
POWER SOCKET
REMOVAL AND INSTALLATION
POWER SOCKET
FRONT POWER SOCKET
FRONT POWER SOCKET : Exploded View
INFOID:0000000008462882
FRONT POWER SOCKET : Removal and Installation
INFOID:0000000008462883
REMOVAL
1.
Remove front console pocket. Refer to
.
2.
Disconnect power socket connector (A).
3.
Pull out inner socket (1) by pushing the ring pawl (B) from the
inner socket hole (square) (C).
4.
Remove ring (2) from front console pocket while pressing pawls.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Align the cut outs of inner socket, ring, and front console pocket.
CONSOLE POWER SOCKET
CONSOLE POWER SOCKET : Exploded View
INFOID:0000000008462884
CONSOLE POWER SOCKET : Removal and Installation
INFOID:0000000008462885
REMOVAL
1
: Inner socket
2
: Ring
JPMIA0782ZZ
D
: Cut out
JPMIA0783ZZ
1
: Inner socket
2
: Ring
JSMIA0522ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
PWO
POWER SOCKET
PWO-5
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
1.
Remove console finisher assembly. Refer to
.
2.
Disconnect power socket connector (A).
3.
Pull out inner socket (1) by pushing the ring pawl (C) from the
inner socket hole (square) (D).
4.
Remove ring (2) from console box while pressing pawls.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Align the cut outs of inner socket, ring, and console box.
B
: Hole for power socket
(Console box)
E
: Cut out
JSMIA0233ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
RAX-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
RAX
A
B
RAX
N
O
P
CONTENTS
REAR AXLE
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Drive Shaft . . . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
REAR WHEEL HUB AND HOUSING . . . . .
Inspection . . . . . . . . . . . . . . . . ..
REAR DRIVE SHAFT . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
REAR WHEEL HUB AND HOUSING . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . .
REAR DRIVE SHAFT . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
WHEEL SIDE . . . . . . . . . . . . . . . .
WHEEL SIDE : Disassembly and Assembly . . ...
FINAL DRIVE SIDE . . . . . . . . . . . . .
FINAL DRIVE SIDE : Disassembly and Assembly .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Bearing . . . . . . . . . . . . . . .
Drive Shaft . . . . . . . . . . . . . . . ...
Revision: 2012 October
2013 Murano CrossCabriolet
RAX-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precautions for Drive Shaft
INFOID:0000000008461603
• Observe the following precautions when disassembling and assembling drive shaft.
• Never disassemble joint sub-assembly because it is non-overhaul parts.
• Perform work in a location which is as dust-free as possible.
• Clean the parts, before disassembling and assembling.
• Prevent the entry of foreign objects during disassembly of the service location.
• Reassemble disassembled parts carefully in the correct order. If work is interrupted, a clean cover must be
placed over parts.
• Use paper waste. Do not use fabric shop cloths because of the danger of lint adhering to parts.
• Clean disassembled parts (except for rubber parts) with kerosene which shall be removed by blowing with
air or wiping with paper waste.
Revision: 2012 October
2013 Murano CrossCabriolet
PREPARATION
RAX-3
< PREPARATION >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000008461604
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
Revision: 2012 October
2013 Murano CrossCabriolet
RAX-4
< SYMPTOM DIAGNOSIS >
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000008461605
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference
—
—
—
NVH in DLN section
NVH in DLN section
NVH in RAX
and RSU
sections
Refer to REAR AXLE i
n
t
h
is chart
NVH in WT
section
NVH in WT
section
Ref
e
r t
o
DRIVE
SHAFT
in this
chart
NVH in BR
section
Possible cause and SUSPECTED PARTS
Ex
ce
ss
iv
e j
oi
nt
an
gl
e
Jo
in
t s
lid
in
g re
si
st
an
ce
Imb
al
anc
e
Im
p
rop
er i
n
s
ta
lla
tio
n
,
loo
s
en
es
s
P
a
rt
s interference
PR
OP
EL
LE
R
S
H
A
F
T
DIFFERENTIAL
REA
R
AXLE AND REAR S
U
SPENSION
REA
R
AXLE
TI
RE
ROAD W
H
EEL
DRIV
E SHAFT
BR
AK
E
Symptom
DRIVE
SHAFT
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
REAR AXLE
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
Judder
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
Revision: 2012 October
2013 Murano CrossCabriolet
REAR WHEEL HUB AND HOUSING
RAX-5
< PERIODIC MAINTENANCE >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PERIODIC MAINTENANCE
REAR WHEEL HUB AND HOUSING
Inspection
INFOID:0000000008461606
MOUNTING INSPECTION
Make sure the mounting conditions (looseness, back lash) of each component and component conditions
(wear, damage) are normal.
WHEEL BEARING INSPECTION
• Move wheel hub and bearing assembly in the axial direction by hand. Make sure there is no looseness of
wheel bearing.
• Rotate wheel hub and bearing assembly and make sure there is no unusual noise or other irregular condi-
tions. If there is any of irregular conditions, replace wheel hub and bearing assembly.
Standard
Axial end play
: Refer to
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст