Murano Cross Cabriolet Z51 (2013 year). Manual — part 71
DOOR KEY CYLINDER SWITCH
PWC-45
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-66, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK DOOR KEY CYLINDER SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between front door lock assembly (driver side) (door key cylinder switch) harness con-
nector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK DOOR KEY CYLINDER SWITCH
PWC-45, "Component Inspection"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> Replace front door lock assembly (driver side) (door key cylinder switch).
Component Inspection
INFOID:0000000008463253
1.
CHECK DOOR KEY CYLINDER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) (door key cylinder switch) connector.
3.
Check front door lock assembly (driver side) (door key cylinder switch) terminals under the following con-
ditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front door lock assembly (driver side) (door key cylinder switch).
Power window main switch
Ground
Continuity
Connector
Terminal
D5
4
Not existed
6
Front door lock assembly (driver side)
(door key cylinder switch)
Ground
Continuity
Connector
Terminal
D9
4
Existed
Terminal
Condition
Continuity
5
4
Unlock
Existed
Neutral / Lock
Not existed
6
Lock
Existed
Neutral / Unlock
Not existed
Revision: 2012 October
2013 Murano CrossCabriolet
PWC-46
< DTC/CIRCUIT DIAGNOSIS >
POWER WINDOW SERIAL LINK
POWER WINDOW SERIAL LINK
POWER WINDOW MAIN SWITCH
POWER WINDOW MAIN SWITCH : Diagnosis Procedure
INFOID:0000000008463254
1.
CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check signal between power window main switch harness connector and ground using an oscilloscope.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 2.
2.
CHECK POWER WINDOW SERIAL LINK SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between power window main switch harness connector and ground.
Is the measurement value within the specification?
YES
>> Replace power window main switch. Refer to
PWC-66, "Removal and Installation"
NO
>> GO TO 3.
3.
CHECK POWER WINDOW SERIAL LINK CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect soft top control unit connector.
3.
Check continuity between soft top control unit harness connector and power window main switch harness
connector.
4.
Check continuity between soft top control unit harness connector and ground.
Is the inspection result normal?
(+)
(–)
Signal
(Reference value)
Power window main switch
Connector
Terminal
D5
14
Ground
JPMIA0013GB
(+)
(–)
Voltage (V)
(Approx.)
Power window main switch
Connector
Terminal
D5
14
Ground
12
Soft top control unit
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
B323
19
D5
14
Existed
Soft top control unit
Ground
Continuity
Connector
Terminal
B323
19
Not existed
Revision: 2012 October
2013 Murano CrossCabriolet
POWER WINDOW SERIAL LINK
PWC-47
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
YES
>> Replace soft top control unit. Refer to
RF-229, "Removal and Installation"
.
NO
>> Repair or replace harness.
FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
FRONT POWER WINDOW SWITCH (PASSENGER SIDE) : Diagnosis Procedure
INFOID:0000000008463255
1.
CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check signal between front power window switch (passenger side) harness connector and ground using
an oscilloscope.
Is the inspection result normal?
YES
>> Replace front power window switch (passenger side). Refer to
PWC-66, "Removal and Installa-
.
NO
>> GO TO 2.
2.
CHECK POWER WINDOW SERIAL LINK CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector and front power window switch (passenger side) con-
nector.
3.
Check continuity between power window main switch harness connector and front power window switch
(passenger side) harness connector.
4.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-66, "Removal and Installation"
NO
>> Repair or replace harness.
REAR POWER WINDOW SWITCH LH
REAR POWER WINDOW SWITCH LH : Diagnosis Procedure
INFOID:0000000008463256
1.
CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check signal between rear power window switch LH harness connector and ground using an oscillo-
scope.
(+)
(
−
)
Signal
(Reference value)
Front power window switch (passenger side)
Connector
Terminal
D45
16
Ground
JPMIA0013GB
Power window main switch
Front power window switch (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
D5
14
D45
16
Existed
Power window main switch
Ground
Continuity
Connector
Terminal
D5
14
Not existed
Revision: 2012 October
2013 Murano CrossCabriolet
PWC-48
< DTC/CIRCUIT DIAGNOSIS >
POWER WINDOW SERIAL LINK
Is the inspection result normal?
YES
>> Replace rear power window switch LH. Refer to
PWC-66, "Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK POWER WINDOW SERIAL LINK CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector and rear power window switch LH connector.
3.
Check continuity between power window main switch harness connector and rear power window switch
LH harness connector.
4.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-66, "Removal and Installation"
NO
>> Repair or replace harness.
REAR POWER WINDOW SWITCH RH
REAR POWER WINDOW SWITCH RH : Diagnosis Procedure
INFOID:0000000008463257
1.
CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check signal between rear power window switch RH harness connector and ground using an oscillo-
scope.
Is the inspection result normal?
(+)
(
−
)
Signal
(Reference value)
Rear power window switch LH
Connector
Terminal
B42
16
Ground
JPMIA0013GB
Power window main switch
Rear power window switch LH
Continuity
Connector
Terminal
Connector
Terminal
D5
14
B42
16
Existed
Power window main switch
Ground
Continuity
Connector
Terminal
D5
14
Not existed
(+)
(
−
)
Signal
(Reference value)
Rear power window switch RH
Connector
Terminal
B222
16
Ground
JPMIA0013GB
Revision: 2012 October
2013 Murano CrossCabriolet
POWER WINDOW SERIAL LINK
PWC-49
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
YES
>> Replace rear power window switch RH. Refer to
PWC-66, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK POWER WINDOW SERIAL LINK CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector and rear power window switch RH connector.
3.
Check continuity between power window main switch harness connector and rear power window switch
RH harness connector.
4.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-66, "Removal and Installation"
NO
>> Repair or replace harness.
Power window main switch
Rear power window switch RH
Continuity
Connector
Terminal
Connector
Terminal
D5
14
B222
16
Existed
Power window main switch
Ground
Continuity
Connector
Terminal
D5
14
Not existed
Revision: 2012 October
2013 Murano CrossCabriolet
PWC-50
< DTC/CIRCUIT DIAGNOSIS >
DOOR SWITCH
DOOR SWITCH
DRIVER SIDE
DRIVER SIDE : Component Function Check
INFOID:0000000008463258
1.
CHECK FUNCTION
Check that automatic adjusting function operates normally when driver side door is opened.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
PWC-50, "DRIVER SIDE : Diagnosis Procedure"
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000008463259
1.
CHECK FRONT DOOR SWITCH (DRIVER SIDE)
DLK-55, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning parts.
2.
CHECK FRONT DOOR SWITCH (DRIVER SIDE) CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect front door switch (driver side) connector and power window main switch connector.
3.
Check continuity between front door switch (driver side) harness connector and power window main
switch harness connector.
4.
Check continuity between front door switch (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-66, "Removal and Installation"
NO
>> Replace or repair harness.
PASSENGER SIDE
PASSENGER SIDE : Component Function Check
INFOID:0000000008463260
1.
CHECK FUNCTION
Check that automatic adjusting function operates normally when passenger side door is opened.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
PWC-50, "PASSENGER SIDE : Diagnosis Procedure"
.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000008463261
1.
CHECK FRONT DOOR SWITCH (PASSENGER SIDE)
DLK-55, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning parts.
Front door switch (driver side)
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
B32
3
D5
5
Existed
Front door switch (driver side)
Ground
Continuity
Connector
Terminal
B32
3
Not existed
Revision: 2012 October
2013 Murano CrossCabriolet
DOOR SWITCH
PWC-51
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
2.
CHECK FRONT DOOR SWITCH (PASSENGER SIDE) CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect front door switch (passenger side) connector and front power window switch (passenger side)
connector.
3.
Check continuity between front door switch (passenger side) harness connector and front power window
switch (passenger side) harness connector.
4.
Check continuity between front door switch (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window switch (passenger side). Refer to
PWC-66, "Removal and Installa-
.
NO
>> Replace or repair harness.
Front door switch (passenger side)
Front power window switch (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
B233
3
D45
14
Existed
Front door switch (passenger side)
Ground
Continuity
Connector
Terminal
B233
3
Not existed
Revision: 2012 October
2013 Murano CrossCabriolet
PWC-52
< SYMPTOM DIAGNOSIS >
NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY SWITCH
SYMPTOM DIAGNOSIS
NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY
SWITCH
Diagnosis Procedure
INFOID:0000000008463262
1.
CHECK DTC WITH SOFT TOP CONTROL UNIT
Check that DTC is not detected with soft top control unit.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
.
2.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Check BCM power supply and ground circuit.
Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY AND GROUND CIRCUIT
Check power window main switch power supply and ground circuit.
Refer to
PWC-28, "POWER WINDOW MAIN SWITCH : Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK POWER WINDOW MAIN SWITCH SERIAL LINK CIRCUIT
Check power window main switch serial link circuit.
Refer to
PWC-46, "POWER WINDOW MAIN SWITCH : Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
REPLACE POWER WINDOW MAIN SWITCH
1.
Replace power window main switch. Refer to
PWC-66, "Removal and Installation"
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2012 October
2013 Murano CrossCabriolet
DRIVER SIDE POWER WINDOW DOES NOT OPERATE
PWC-53
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
DRIVER SIDE POWER WINDOW DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000008463263
1.
CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) CIRCUIT
Check front power window motor (driver side) circuit.
Refer to
PWC-31, "DRIVER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2012 October
2013 Murano CrossCabriolet
PWC-54
< SYMPTOM DIAGNOSIS >
FRONT PASSENGER SIDE POWER WINDOW DOES NOT OPERATE
FRONT PASSENGER SIDE POWER WINDOW DOES NOT OPERATE
WHEN BOTH POWER WINDOW MAIN SWITCH AND FRONT POWER WINDOW
SWITCH ARE OPERATED
WHEN BOTH POWER WINDOW MAIN SWITCH AND FRONT POWER WINDOW
SWITCH ARE OPERATED : Diagnosis Procedure
INFOID:0000000008463264
1.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) POWER SUPPLY AND GROUND CIR-
CUIT
Check front power window switch (passenger side) power supply and ground circuit.
Refer to
PWC-29, "FRONT POWER WINDOW SWITCH (PASSENGER SIDE) : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE) CIRCUIT
Check front power window motor (passenger side) circuit.
Refer to
PWC-32, "PASSENGER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
WHEN FRONT POWER WINDOW SWITCH (PASSENGER SIDE) IS OPERATED
WHEN FRONT POWER WINDOW SWITCH (PASSENGER SIDE) IS OPERATED :
Diagnosis Procedure
INFOID:0000000008463265
1.
REPLACE FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
Replace front power window switch (passenger side).
Refer to
PWC-66, "Removal and Installation"
.
>> INSPECTION END
WHEN POWER WINDOW MAIN SWITCH IS OPERATED
WHEN POWER WINDOW MAIN SWITCH IS OPERATED : Diagnosis Procedure
INFOID:0000000008463266
1.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) SERIAL LINK CIRCUIT
Check front power window switch (passenger side) serial link circuit.
Refer to
PWC-47, "FRONT POWER WINDOW SWITCH (PASSENGER SIDE) : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2012 October
2013 Murano CrossCabriolet
REAR LH SIDE POWER WINDOW DOES NOT OPERATE
PWC-55
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
REAR LH SIDE POWER WINDOW DOES NOT OPERATE
WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW
SWITCH LH ARE OPERATED
WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW
SWITCH LH ARE OPERATED : Diagnosis Procedure
INFOID:0000000008463267
1.
CHECK REAR POWER WINDOW SWITCH LH POWER SUPPLY AND GROUND CIRCUIT
Check rear power window switch LH power supply and ground circuit.
Refer to
PWC-29, "REAR POWER WINDOW SWITCH : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK REAR POWER WINDOW MOTOR LH
Check rear power window motor LH.
Refer to
PWC-33, "REAR LH : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
WHEN REAR POWER WINDOW SWITCH LH IS OPERATED
WHEN REAR POWER WINDOW SWITCH LH IS OPERATED : Diagnosis Procedure
INFOID:0000000008463268
1.
REPLACE REAR POWER WINDOW SWITCH LH
Replace rear power window switch LH.
Refer to
PWC-66, "Removal and Installation"
.
>> INSPECTION END
WHEN POWER WINDOW MAIN SWITCH IS OPERATED
WHEN POWER WINDOW MAIN SWITCH IS OPERATED : Diagnosis Procedure
INFOID:0000000008463269
1.
CHECK REAR POWER WINDOW SWITCH LH SERIAL LINK CIRCUIT
Check rear power window switch LH serial link circuit.
Refer to
PWC-47, "REAR POWER WINDOW SWITCH LH : Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2012 October
2013 Murano CrossCabriolet
PWC-56
< SYMPTOM DIAGNOSIS >
REAR RH SIDE POWER WINDOW DOES NOT OPERATE
REAR RH SIDE POWER WINDOW DOES NOT OPERATE
WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW
SWITCH RH ARE OPERATED
WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW
SWITCH RH ARE OPERATED : Diagnosis Procedure
INFOID:0000000008463270
1.
CHECK REAR POWER WINDOW SWITCH RH POWER SUPPLY AND GROUND CIRCUIT
Check rear power window switch RH power supply and ground circuit.
Refer to
PWC-29, "REAR POWER WINDOW SWITCH : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK REAR POWER WINDOW MOTOR RH
Check rear power window motor RH.
Refer to
PWC-33, "REAR RH : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
WHEN REAR POWER WINDOW SWITCH RH IS OPERATED
WHEN REAR POWER WINDOW SWITCH RH IS OPERATED : Diagnosis Procedure
INFOID:0000000008463271
1.
REPLACE REAR POWER WINDOW SWITCH RH
Replace rear power window switch RH.
Refer to
PWC-66, "Removal and Installation"
.
>> INSPECTION END
WHEN POWER WINDOW MAIN SWITCH IS OPERATED
WHEN POWER WINDOW MAIN SWITCH IS OPERATED : Diagnosis Procedure
INFOID:0000000008463272
1.
CHECK REAR POWER WINDOW SWITCH RH SERIAL LINK CIRCUIT
Check rear power window switch RH serial link circuit.
Refer to
PWC-48, "REAR POWER WINDOW SWITCH RH : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2012 October
2013 Murano CrossCabriolet
AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATES NORMAL-
LY
PWC-57
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATES
NORMALLY
DRIVER SIDE
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000008463273
1.
PERFORM INITIALIZATION PROCEDURE
Initialization procedure is executed and operation is confirmed.
Refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK ENCODER CIRCUIT (DRIVER SIDE)
Check encoder circuit (driver side).
Refer to
PWC-35, "DRIVER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE POWER WINDOW MAIN SWITCH
1.
Replace power window main switch. Refer to
PWC-66, "Removal and Installation"
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
PASSENGER SIDE
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000008463274
1.
PERFORM INITIALIZATION PROCEDURE
Initialization procedure is executed and operation is confirmed.
Refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK ENCODER CIRCUIT (PASSENGER SIDE)
Check encoder circuit (passenger side).
Refer to
PWC-37, "PASSENGER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE FRONT POWER WINDOW SWITCH (PASSENGER SIEDE)
1.
Replace front power window switch (passenger side). Refer to
PWC-66, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
REAR LH
Revision: 2012 October
2013 Murano CrossCabriolet
PWC-58
< SYMPTOM DIAGNOSIS >
AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATES NORMAL-
LY
REAR LH : Diagnosis Procedure
INFOID:0000000008463275
1.
CHECK ENCODER (REAR LH) CIRCUIT
Check encoder (rear LH) circuit.
Refer to
PWC-39, "REAR LH : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE REAR POWER WINDOW SWITCH LH
1.
Replace rear power window switch LH. Refer to
PWC-66, "Removal and Installation"
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
REAR RH
REAR RH : Diagnosis Procedure
INFOID:0000000008463276
1.
CHECK ENCODER (REAR RH) CIRCUIT
Check encoder (rear RH) circuit.
Refer to
PWC-41, "REAR RH : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE REAR POWER WINDOW SWITCH RH
1.
Replace rear power window switch RH. Refer to
PWC-66, "Removal and Installation"
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2012 October
2013 Murano CrossCabriolet
ANTI-PINCH FUNCTION DOES NOT OPERATE NORMALLY
PWC-59
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
ANTI-PINCH FUNCTION DOES NOT OPERATE NORMALLY
Diagnosis Procedure
INFOID:0000000008463277
1.
CHECK POWER WINDOW AUTO OPERATION
Check AUTO operation when anti-pinch function does not operate.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
PWC-57, "DRIVER SIDE : Diagnosis Procedure"
(driver side),
(passenger side).
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2012 October
2013 Murano CrossCabriolet
PWC-60
< SYMPTOM DIAGNOSIS >
AUTOMATIC WINDOW ADJUSTING FUNCTION DOES NOT OPERATE
AUTOMATIC WINDOW ADJUSTING FUNCTION DOES NOT OPERATE
DRIVER SIDE
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000008463278
1.
CHECK AUTO UP OPERATION
Check AUTO operation when automatic window adjusting function does not operate.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
PWC-57, "DRIVER SIDE : Diagnosis Procedure"
2.
CHECK FRONT DOOR SWITCH (DRIVER SIDE)
Check front door switch (driver side).
Refer to
PWC-50, "DRIVER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE POWER WINDOW MAIN SWITCH
1.
Replace power window main switch. Refer to
PWC-66, "Removal and Installation"
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
PASSENGER SIDE
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000008463279
1.
CHECK AUTO UP OPERATION
Check AUTO operation when automatic window adjusting function does not operate.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
PWC-57, "PASSENGER SIDE : Diagnosis Procedure"
.
2.
CHECK FRONT DOOR SWITCH (PASSENGER SIDE)
Check front door switch (passenger side).
Refer to
PWC-50, "PASSENGER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
1.
Replace front power window switch (passenger side). Refer to
PWC-66, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст