Murano Cross Cabriolet Z51 (2013 year). Manual — part 61
CHASSIS MAINTENANCE
MA-23
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
8.
Place the selector lever in “P” or “N” and check that the fluid
level is within the specified range.
CAUTION:
When reinstalling CVT fluid level gauge, insert it into the
CVT fluid charging pipe and rotate it to the original installa-
tion position until securely locked.
CVT FLUID CONDITION
Check CVT fluid condition.
• If CVT fluid is very dark or smells burned, check operation of CVT.
Flush cooling system after repair of CVT.
• If CVT fluid contains frictional material (clutches, brakes, etc.),
replace radiator and flush cooler line using cleaning solvent and
compressed air after repair of CVT. Refer to
.
CVT FLUID : Changing
INFOID:0000000008462005
CAUTION:
Replace an O-ring with new ones at the final stage of the operation when installing.
1.
Remove drain plug from oil pan.
2.
Remove O-ring from drain plug.
3.
Install O-ring to drain plug.
CAUTION:
Never reuse O-ring.
4.
Install drain plug to oil pan. Refer to
.
5.
Fill CVT fluid from CVT fluid charging pipe to the specified level.
CAUTION:
• Use only Genuine NISSAN CVT Fluid NS-3. Never mix with other fluid.
• Using CVT fluid other than Genuine NISSAN CVT Fluid NS-3 will deteriorate in driveability and
CVT durability, and may damage the CVT, which is not covered by the warranty.
• When filling CVT fluid, take care not to scatter heat generating parts such as exhaust.
• Sufficiently shake the container of CVT fluid before using.
• Delete CVT fluid deterioration date with CONSULT after changing CVT fluid. Refer to
6.
With the engine warmed up, drive the vehicle in an urban area.
NOTE:
When ambient temperature is 20
°
C (68
°
F), it takes about 10 minutes for the CVT fluid to warm up to 50 –
80
°
C (122 – 176
°
F).
SCIA1932E
Fluid status
Conceivable cause
Required operation
Varnished (viscous
varnish state)
CVT fluid becomes
degraded due to
high temperatures.
Replace the CVT fluid and check the
CVT main unit and the vehicle for
malfunctions (wire harnesses, cool-
er pipes, etc.).
Milky white or
cloudy
Water in the fluid
Replace the CVT fluid and check for
places where water is getting in.
Large amount of
metal powder mixed
in
Unusual wear of
sliding parts within
CVT
Replace the CVT fluid and check for
improper operation of the CVT.
ATA0022D
CVT fluid
: Refer to
TM-167, "General Specification"
Fluid capacity
: Refer to
TM-167, "General Specification"
Revision: 2012 October
2013 Murano CrossCabriolet
MA-24
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
7.
Check CVT fluid level and condition.
8.
Repeat steps 1 to 5 if CVT fluid has been contaminated.
9.
Select “Work Support” in “TRANSMISSION” with CONSULT.
10. Select “CONFORM CVTF DETERIORTN”.
11. Touch “Clear”.
TRANSFER OIL
TRANSFER OIL : Inspection
INFOID:0000000008462006
OIL LEAKAGE
Check transfer surrounding area (oil seal, drain plug, filler plug, and transfer case, etc.) for oil leakage.
OIL LEVEL
1.
Remove filler plug (1) and gasket. Then check that oil is filled up
(A) from mounting hole for the filler plug.
2.
Before installing filler plug, set a new gasket. Install filler plug on
transfer and tighten to the specified torque. Refer to
CAUTION:
Never reuse gaskets.
TRANSFER OIL : Draining
INFOID:0000000008462007
1.
Run the vehicle to warm up the transfer unit sufficiently.
2.
Stop the engine and remove drain plug (1) and gaskets to drain
the transfer oil.
3.
Before installing drain plug, set a new gasket. Install drain plug
on transfer and tighten to the specified torque. Refer to
CAUTION:
Never reuse gaskets.
TRANSFER OIL : Refilling
INFOID:0000000008462008
1.
Remove filler plug (1) and gasket. Then fill oil up to mounting
hole (A) for the filler plug.
CAUTION:
Carefully fill the oil. (Fill up for approximately 3 minutes.)
2.
Leave the vehicle for 3 minutes. Then check oil level again.
3.
Before installing filler plug, set a new gasket. Install filler plug on transfer and tighten to the specified
torque. Refer to
: Vehicle front
JPDIE0017ZZ
: Vehicle front
JPDIE0016ZZ
: Vehicle front
Oil grade and viscosity
: Refer to
.
Oil capacity
: Refer to
.
JPDIE0017ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
CHASSIS MAINTENANCE
MA-25
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
CAUTION:
Never reuse gasket.
REAR PROPELLER SHAFT
REAR PROPELLER SHAFT : Inspection
INFOID:0000000008462009
APPEARANCE AND NOISE
• Check the propeller shaft tube surface for dents or cracks. If damaged, replace propeller shaft assembly.
• If center bearing is noisy or damaged, replace propeller shaft assembly.
VIBRATION
If vibration is present at high speed, inspect propeller shaft runout first.
1.
With a dial indicator, measure propeller shaft runout at runout
measuring points by rotating final drive companion flange with
hands.
• Propeller shaft runout measuring point (Point “ ”).
2.
If runout still exceeds specifications, separate propeller shaft at
final drive companion flange or transfer companion flange; then
change the phase between companion flange and propeller
shaft by the one bolt hole at a time and install propeller shaft.
3.
If runout is more than the limit value, remove and check propeller shaft.
4.
Check the vibration by driving vehicle.
REAR DIFFERENTIAL GEAR OIL
REAR DIFFERENTIAL GEAR OIL : Inspection
INFOID:0000000008462010
OIL LEAKAGE
Check that oil is not leaking from final drive assembly or around it.
OIL LEVEL
• Remove filler plug (1) and check oil level from filler plug mounting
hole as shown in the figure.
CAUTION:
Never start engine while checking oil level.
• Set a new gasket on filler plug and install it on final drive assembly.
.
CAUTION:
Never reuse gasket.
Propeller shaft runout
: Refer to
.
JPDID0172ZZ
: Vehicle front
Dimension
A: 506.5 mm (19.94 in)
B: 497.5 mm (19.59 in)
JPDID0156ZZ
JPDID0164ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
MA-26
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
REAR DIFFERENTIAL GEAR OIL : Draining
INFOID:0000000008462011
1.
Stop engine.
2.
Remove drain plug (1) and drain gear oil.
3.
Set a new gasket on drain plug and install it to final drive assem-
bly and tighten to the specified torque. Refer to
CAUTION:
Never reuse gasket.
REAR DIFFERENTIAL GEAR OIL : Refilling
INFOID:0000000008462012
1.
Remove filler plug (1). Fill with new gear oil until oil level reaches
the specified level near filler plug mounting hole.
2.
After refilling oil, check oil level. Set a new gasket to filler plug,
then install it to final drive assembly. Refer to
CAUTION:
Never reuse gasket.
WHEELS (BONDING WEIGHT TYPE)
WHEELS (BONDING WEIGHT TYPE) : Wheel Balance Adjustment
INFOID:0000000008462013
PREPARATION BEFORE ADJUSTMENT
Using releasing agent, remove double-faced adhesive tape from the road wheel.
CAUTION:
• Be careful not to scratch the road wheel during removal.
• After removing double-faced adhesive tape, wipe clean traces of releasing agent from the road
wheel.
ADJUSTMENT
• The details of the adjustment procedure are different for each model of wheel balancer. Therefore, refer to
each instruction manual.
• If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting,
select and adjust a drive-in weight mode suitable for aluminum wheels.
1.
Set road wheel on tire balance machine using the center hole as a guide. Start the tire balance machine.
2.
When inner and outer unbalance values are shown on the tire balance machine indicator, multiply outer
unbalance value by 5/3 to determine balance weight that should be used. Select the outer balance weight
with a value closest to the calculated value above and install to the designated outer position of, or at the
designated angle in relation to the road wheel.
CAUTION:
• Do not install the inner balance weight before installing the outer balance weight.
• Before installing the balance weight, be sure to clean the mating surface of the road wheel.
JPDID0163ZZ
Oil grade and viscosity
: Refer to
.
Oil capacity
: Refer to
JPDID0164ZZ
Revision: 2012 October
2013 Murano CrossCabriolet
CHASSIS MAINTENANCE
MA-27
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
a.
Indicated unbalance value
×
5/3 = balance weight to be installed
Calculation example:
23 g (0.81 oz)
×
5/3 = 38.33 g (1.35 oz)
⇒
40 g (1.41 oz) balance
weight (closer to calculated balance weight value)
NOTE:
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
37.4
⇒
35 g (1.23 oz)
37.5
⇒
40 g (1.41 oz)
b.
Installed balance weight in the position.
• When installing balance weight (1) to road wheels, set it into
the grooved area (A) on the inner wall of the road wheel as
shown in the figure so that the balance weight center (B) is
aligned with the tire balance machine indication position
(angle) (C).
CAUTION:
• Always use genuine NISSAN adhesion balance weights.
• Balance weights are non-reusable; always replace with
new ones.
• Do not install more than three sheets of balance weight.
c.
If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight sheets in line with each other as shown in
the figure.
CAUTION:
Do not install one balance weight sheet on top of another.
3.
Start the tire balance machine again.
4.
Install drive-in balance weight on inner side of road wheel in the
tire balance machine indication position (angle).
CAUTION:
Do not install more than two balance weight.
5.
Start the tire balance machine. Make sure that inner and outer
residual unbalance values are 5 g (0.17 oz) each or below.
CAUTION:
If either residual unbalance value exceeds limit, repeat installation procedures.
SMA054D
JPEIC0040ZZ
Limit
Dynamic (At flange):
Refer to
.
Static (At flange):
Refer to
.
PEIA0033E
Revision: 2012 October
2013 Murano CrossCabriolet
MA-28
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
WHEELS (BONDING WEIGHT TYPE) : Tire Rotation
INFOID:0000000008462014
• Follow the maintenance schedule for tire rotation service intervals.
MA-4, "Explanation of General Maintenance"
• When installing the wheel, tighten wheel nuts to the specified
.
CAUTION:
• Do not include the T-type spare tire when rotating the tires.
• When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
• Be careful not to tighten wheel nut at torque exceeding the
criteria for preventing strain of disc rotor.
• Use NISSAN genuine wheel nuts for aluminum wheels.
• Perform the ID registration, after tire rotation. Refer to
BRAKE FLUID LEVEL AND LEAKS
BRAKE FLUID LEVEL AND LEAKS : Inspection
INFOID:0000000008462015
• If fluid level is extremely low, check brake system for leaks.
BRAKE LINES AND CABLES
BRAKE LINES AND CABLES : Inspection
INFOID:0000000008462016
• Check brake fluid lines and parking brake cables for improper
attachment, leaks, chafing, abrasions, deterioration, etc.
BRAKE FLUID
SMA829C
JPFIA0295ZZ
SBR389C
Revision: 2012 October
2013 Murano CrossCabriolet
CHASSIS MAINTENANCE
MA-29
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
BRAKE FLUID : Changing
INFOID:0000000008462017
1.
Drain brake fluid from each bleed valve.
2.
Refill until new brake fluid comes out from each bleed valve.
Use same procedure as in bleeding hydraulic system to refill
brake fluid.
Refer to
BR-11, "Bleeding Brake System"
• Refill with recommended brake fluid.
Refer to
MA-10, "Fluids and Lubricants"
• Never reuse drained brake fluid.
• Be careful not to splash brake fluid on painted areas.
DISC BRAKE
DISC BRAKE : Inspection
INFOID:0000000008462018
DISC ROTOR
Check condition, wear, and damage.
CALIPER
• Check for leakage.
BRAKE PAD
• Check for wear or damage.
DISC BRAKE : Front Disc Brake
INFOID:0000000008462019
Unit: mm (in)
SBR419C
SMA922A
BRA0010D
Item
Limit
Brake pad
Wear thickness
2.0 (0.079)
Disc rotor
Wear thickness
26.0 (1.024)
Thickness variation (measured at 8 positions)
0.008 (0.0003)
Runout (with it attached to the vehicle)
0.040 (0.0016) or less
Revision: 2012 October
2013 Murano CrossCabriolet
MA-30
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
DISC BRAKE : Rear Disc Brake
INFOID:0000000008462020
Unit: mm (in)
STEERING GEAR AND LINKAGE
STEERING GEAR AND LINKAGE : Inspection
INFOID:0000000008462021
STEERING GEAR
• Check gear housing and boots for looseness, damage and grease
leakage.
• Check connection with steering column for looseness.
STEERING LINKAGE
Check ball joint, dust cover and other component parts for looseness, wear, damage and grease leakage.
POWER STEERING FLUID AND LINES
POWER STEERING FLUID AND LINES : Inspection
INFOID:0000000008462022
Check fluid level in reservoir tank with engine off.
Use “HOT” range at fluid temperatures of 50 to 80
°
C (122 to 176
°
F)
or “COLD” range at fluid temperatures of 0 to 30
°
C (32 to 86
°
F).
CAUTION:
• Do not overfill.
• Recommended fluid is Genuine NISSAN PSF or equivalent.
Refer to
MA-10, "Fluids and Lubricants"
.
• Check lines for improper attachment, leaks, cracks, damage,
loose connections, chafing and deterioration.
• Check rack boots for accumulation of power steering fluid.
AXLE AND SUSPENSION PARTS
Item
Limit
Brake pad
Wear thickness
2.0 (0.079)
Disc rotor
Wear thickness
14.0 (0.551)
Thickness variation (measured at 8 positions)
0.020 (0.0008)
Runout (with it attached to the vehicle)
0.050 (0.0020) or less
SLIA0014E
SST850C
SST851C
Revision: 2012 October
2013 Murano CrossCabriolet
CHASSIS MAINTENANCE
MA-31
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
AXLE AND SUSPENSION PARTS : Inspection
INFOID:0000000008462023
Check front and rear axle and suspension parts for excessive play,
cracks, wear or other damage.
• Shake each wheel to check for excessive play.
• Check wheel bearings for smooth operation.
• Check axle and suspension nuts and bolts for looseness.
• Check strut (shock absorber) for oil leakage or other damage.
• Check suspension ball joint for grease leakage and ball joint dust
cover for cracks or other damage.
DRIVE SHAFT
DRIVE SHAFT : Inspection
INFOID:0000000008462024
• Check boot and drive shaft for cracks, wear, damage and grease
leakage.
SMA525A
JPPIA0011ZZ
SFA108A
Revision: 2012 October
2013 Murano CrossCabriolet
MA-32
< PERIODIC MAINTENANCE >
BODY MAINTENANCE
BODY MAINTENANCE
LOCKS, HINGES AND HOOD LATCH
LOCKS, HINGES AND HOOD LATCH : Lubricating
INFOID:0000000008462025
For hood and hood lock illustration.
• Hood lock control: Refer to
For door and door lock illustration.
• Door: Refer to
.
• Door lock: Refer to
For trunk lid and trunk lid lock illustration.
• Trunk lid: Refer to
• Trunk lid lock: Refer to
.
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS : Inspection
INFOID:0000000008462026
For front seat belt illustration. Refer to
For rear seat belt illustration. Refer to
.
CAUTION:
• After any collision, inspect all seat belt assemblies, including retractors and other attached hard-
wares (I.e. anchor bolt, guide rail set). Nissan recommends to replace all seat belt assemblies in use
during a collision, unless not damaged and properly operating after minor collision.
Also inspect seat belt assemblies not in use during a collision, and replace if damaged or improperly
operating.
Seat belt pre-tensioner should be replaced even if the seat belts are not in use during a frontal colli-
sion where the driver and passenger air bags are deployed.
• If any component of seat belt assembly is questionable, do not repair.
Replace as seat belt assembly.
• If webbing is cut, frayed, or damaged, replace belt assembly.
• Never oil tongue and buckle.
• Use a genuine NISSAN seat belt assembly.
For details, refer to
SB-5, "SEAT BELT RETRACTOR : Inspection"
in SB section.
• Check anchors for loose mounting
• Check belts for damage
• Check retractor for smooth operation
• Check function of buckles and tongues when buckled and released
Revision: 2012 October
2013 Murano CrossCabriolet
SERVICE DATA AND SPECIFICATIONS (SDS)
MA-33
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
DRIVE BELT
DRIVE BELT : Drive Belt
INFOID:0000000008462027
DRIVE BELT
ENGINE COOLANT
ENGINE COOLANT : Periodical Maintenance Specification
INFOID:0000000008462028
ENGINE COOLANT CAPACITY (APPROXIMATE)
Unit:
(US qt, lmp qt)
ENGINE OIL
ENGINE OIL : Periodical Maintenance Specification
INFOID:0000000008462029
ENGINE OIL CAPACITY (APPROXIMATE)
Unit:
(US qt, lmp qt)
SPARK PLUG
SPARK PLUG : Spark Plug
INFOID:0000000008462030
SPARK PLUG
Unit: mm (in)
ROAD WHEEL
ROAD WHEEL : Road Wheel
INFOID:0000000008462031
ALUMINUM WHEEL
Tension of drive belt
Belt tension is not necessary, as it is automatically adjusted by drive belt auto-tensioner.
Engine coolant capacity (With reservoir tank at “MAX” level)
9.0 (9-1/2, 7-7/8)
Reservoir tank
0.8 (7/8, 3/4)
Drain and refill
With oil filter change
4.6 (4-7/8, 4)
Without oil filter change
4.3 (4-1/2, 3-3/4)
Dry engine (Overhaul)
5.3 (5-5/8, 4-5/8)
Make
DENSO
Standard type
FXE22HR11
Gap
Standard
1.1 (0.043)
Limit
1.4 (0.055)
Item
Limit
Runout
Axial runout
Less than 0.3 mm (0.012 in)
Radial runout
Allowable unbalance
Dynamic (At flange)
Less than 5 g (0.17 oz) (one side)
Static (At flange)
Less than 10 g (0.35 oz)
Revision: 2012 October
2013 Murano CrossCabriolet
MIR-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
MIR
A
B
MIR
N
O
P
CONTENTS
MIRRORS
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Service Procedure Precautions for Models with a
Pop-up Roll Bar . . . . . . . . . . . . . .....
Precaution for Battery Service . . . . . . . . ..
Precaution for Procedure without Cowl Top Cover
. ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ....
Commercial Service Tools . . . . . . . . . ....
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
DOOR MIRROR . . . . . . . . . . . . . . ...
DOOR MIRROR : Component Parts Location . . ..
DOOR MIRROR : Component Description . . . ...
INSIDE MIRROR . . . . . . . . . . . . . . ..
INSIDE MIRROR : Component Description . . . ..
SYSTEM . . . . . . . . . . . . . . . ..
DOOR MIRROR SYSTEM . . . . . . . . . . ...
DOOR MIRROR SYSTEM : System Diagram . . ..
DOOR MIRROR SYSTEM : System Description . ..
AUTO ANTI-DAZZLING INSIDE MIRROR SYS-
TEM . . . . . . . . . . . . . . . . . . . ..
AUTO ANTI-DAZZLING INSIDE MIRROR SYS-
TEM : System Description . . . . . . . . . .....
ECU DIAGNOSIS INFORMATION . . . ...
DRIVER SEAT CONTROL UNIT, AUTOMAT-
IC DRIVE POSITIONER CONTROL UNIT . . ..
List of ECU Reference . . . . . . . . . . . ..
WIRING DIAGRAM . . . . . . . . . ..
DOOR MIRROR SYSTEM . . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . .
AUTO ANTI-DAZZLING INSIDE MIRROR
SYSTEM . . . . . . . . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . .
SYMPTOM DIAGNOSIS . . . . . . . ..
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES . . . . . . . . . . . . . . . ..
Work Flow . . . . . . . . . . . . . . . .
Inspection Procedure . . . . . . . . . . . ...
Diagnostic Worksheet . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . ...
INSIDE MIRROR . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
DOOR MIRROR . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
DOOR MIRROR ASSEMBLY . . . . . . . . .
DOOR MIRROR ASSEMBLY : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
GLASS MIRROR . . . . . . . . . . . . . .
GLASS MIRROR : Removal and Installation . . ...
DOOR MIRROR COVER . . . . . . . . . . ...
DOOR MIRROR COVER : Removal and Installa-
tion . . . . . . . . . . . . . . . . . . ...
FRONT DOOR CORNER FINISHER . . . . . . .
FRONT DOOR CORNER FINISHER : Removal
and Installation . . . . . . . . . . . . . .
Revision: 2012 October
2013 Murano CrossCabriolet
MIR-2
DOOR MIRROR REMOTE CONTROL
SWITCH . . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Revision: 2012 October
2013 Murano CrossCabriolet
PRECAUTIONS
MIR-3
< PRECAUTION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000008459901
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Service Procedure Precautions for Models with a Pop-up Roll Bar
INFOID:0000000008459902
WARNING:
Always observe the following items for preventing accidental activation.
• Risk of passenger injury or death may increase if the pop-up roll bar does not deploy during a roll
over collision. In order to reduce the chance of an incident where the pop-up roll bar is inoperative,
all maintenance must be performed by a NISSAN or INFINITI dealer.
• Before removing and installing the pop-up roll bar component parts and harness, always turn the
ignition switch OFF, disconnect the battery negative terminal, and wait for 3 minutes or more. (The
purpose of this operation is to discharge electricity that is accumulated in the auxiliary power supply
circuit in the air bag diagnosis sensor unit.)
• When repairing, removing, and installing a pop-up roll bar, always refer to SRS AIR BAG and SRS
AIR BAG CONTROL warnings in the Service Manual.
Precaution for Battery Service
INFOID:0000000008459903
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Revision: 2012 October
2013 Murano CrossCabriolet
MIR-4
< PRECAUTION >
PRECAUTIONS
Precaution for Procedure without Cowl Top Cover
INFOID:0000000008459904
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
PIIB3706J
Revision: 2012 October
2013 Murano CrossCabriolet
PREPARATION
MIR-5
< PREPARATION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000008459905
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000008459906
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-43980)
NISSAN Squeak and Rat-
tle Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes the clips, pawls, and metal clips
Power tool
SIIA0995E
JMKIA3050ZZ
PIIB1407E
Revision: 2012 October
2013 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст