Nissan Juke (2012 year). Service Repair Manual — part 209
SRC-54
< DTC/CIRCUIT DIAGNOSIS >
B1050, B1055 DRIVER AIR BAG MODULE
B1050, B1055 DRIVER AIR BAG MODULE
DTC Logic
INFOID:0000000007578269
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578270
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SPIRAL CABLE
1.
Replace combination switch (spiral cable). Refer to
SR-13, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1050
B1055
DRIVER AIRBAG
MODULE
[VB-SHORT]
Driver air bag module circuit is shorted to
power supply circuit
(including the spiral cable)
• Harness or connectors
(The module circuit is shorted.)
• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1050, B1055 DRIVER AIR BAG MODULE
SRC-55
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
Is DTC detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE DRIVER AIR BAG MODULE
1.
Replace driver air bag module. Refer to
SR-10, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
SRC-56
< DTC/CIRCUIT DIAGNOSIS >
B1051, B1056 DRIVER AIR BAG MODULE
B1051, B1056 DRIVER AIR BAG MODULE
DTC Logic
INFOID:0000000007578271
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578272
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
CHECK SPIRAL CABLE CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.
3.
Check continuity between driver air bag module harness connector and combination switch (spiral cable)
harness connector.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1051
B1056
DRIVER AIRBAG
MODULE
[GND-SHORT]
Driver air bag module circuit is shorted to ground
(including the spiral cable)
• Harness or connectors
(The module circuit is shorted.)
• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1051, B1056 DRIVER AIR BAG MODULE
SRC-57
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
4.
Check continuity between driver air bag module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace combination switch (spiral cable). Refer to
SR-13, "Removal and Installation"
.
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE DRIVER AIR BAG MODULE
1.
Replace driver air bag module. Refer to
SR-10, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Driver air bag module
Combination switch (spiral cable)
Continuity
Connector
Terminal
Connector
Terminal
M301
10
M32
28
Existed
11
30
M300
12
29
9
30
Driver side air bag module
Ground
Continuity
Connector
Terminal
M301
10
Not existed
11
M300
12
9
Revision: 2011 October
2012 JUKE
SRC-58
< DTC/CIRCUIT DIAGNOSIS >
B1052, B1057 DRIVER AIR BAG MODULE
B1052, B1057 DRIVER AIR BAG MODULE
DTC Logic
INFOID:0000000007578273
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578274
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
CHECK SPIRAL CABLE CIRCUIT-I
1.
Turn ignition switch OFF.
2.
Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.
3.
Check continuity between combination switch (spiral cable) terminals.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1052
B1057
DRIVER AIRBAG
MODULE
[SHORT]
Driver air bag module circuit are shorted to each
other
(including the spiral cable)
• Harness or connectors
(The module circuit is shorted.)
• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1052, B1057 DRIVER AIR BAG MODULE
SRC-59
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace combination switch (spiral cable). Refer to
SR-13, "Removal and Installation"
.
4.
CHECK SPIRAL CABLE CIRCUIT-II
Check continuity between combination switch (spiral cable) terminals.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace combination switch (spiral cable). Refer to
SR-13, "Removal and Installation"
.
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 6.
NO
>> INSPECTION END
6.
REPLACE DRIVER AIR BAG MODULE
1.
Replace driver air bag module. Refer to
SR-10, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Combination switch (spiral cable)
Continuity
Connector
Terminal
Connector
Terminal
M301
10
M301
11
Not existed
M300
9
12
Combination switch (spiral cable)
Continuity
Connector
Terminal
Terminal
M32
28
29
Not existed
30
Revision: 2011 October
2012 JUKE
SRC-60
< DTC/CIRCUIT DIAGNOSIS >
B1058, B1059, B1060, B1061, B1062, B1063 DIAGNOSIS SENSOR UNIT
B1058, B1059, B1060, B1061, B1062, B1063 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000007578275
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578276
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1058
B1059
B1060
B1061
B1062
B1063
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1065, B1070 PASSENGER AIR BAG MODULE
SRC-61
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1065, B1070 PASSENGER AIR BAG MODULE
DTC Logic
INFOID:0000000007578277
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578278
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE PASSENGER AIR BAG MODULE
1.
Replace passenger air bag module. Refer to
SR-16, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1065
B1070
ASSIST A/B MODULE
[OPEN]
Passenger air bag module circuit is open
• Harness or connectors
(The module circuit is open.)
• Malfunction in passenger air bag module
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
SRC-62
< DTC/CIRCUIT DIAGNOSIS >
B1065, B1070 PASSENGER AIR BAG MODULE
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
B1066, B1071 PASSENGER AIR BAG MODULE
SRC-63
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1066, B1071 PASSENGER AIR BAG MODULE
DTC Logic
INFOID:0000000007578279
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578280
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE PASSENGER AIR BAG MODULE
1.
Replace passenger air bag module. Refer to
SR-16, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of CON-
SULT
DTC detecting condition
Possible cause
B1066
B1071
ASSIST A/B MODULE
[VB-SHORT]
Passenger air bag module circuit is
shorted to power supply circuit
• Harness or connectors
(The module circuit is shorted.)
• Malfunction in passenger air bag module
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
SRC-64
< DTC/CIRCUIT DIAGNOSIS >
B1066, B1071 PASSENGER AIR BAG MODULE
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
B1067, B1072 PASSENGER AIR BAG MODULE
SRC-65
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1067, B1072 PASSENGER AIR BAG MODULE
DTC Logic
INFOID:0000000007578281
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578282
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE PASSENGER AIR BAG MODULE
1.
Replace passenger air bag module. Refer to
SR-16, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1067
B1072
ASSIST A/B MODULE
[GND-SHORT]
Passenger air bag module circuit is
shorted to ground
• Harness or connectors
(The module circuit is shorted.)
• Malfunction in passenger air bag module
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
SRC-66
< DTC/CIRCUIT DIAGNOSIS >
B1067, B1072 PASSENGER AIR BAG MODULE
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
B1068, B1073 PASSENGER AIR BAG MODULE
SRC-67
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1068, B1073 PASSENGER AIR BAG MODULE
DTC Logic
INFOID:0000000007578283
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578284
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE PASSENGER AIR BAG MODULE
1.
Replace passenger air bag module. Refer to
SR-16, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1068
B1073
ASSIST A/B MODULE
[SHORT]
Passenger air bag module circuits are
shorted to each other
• Harness or connectors
(The module circuit is shorted.)
• Malfunction in passenger air bag module
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
SRC-68
< DTC/CIRCUIT DIAGNOSIS >
B1068, B1073 PASSENGER AIR BAG MODULE
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
B1074, B1075, B1076, B1077, B1078, B1079 DIAGNOSIS SENSOR UNIT
SRC-69
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1074, B1075, B1076, B1077, B1078, B1079 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000007578285
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578286
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1074
B1075
B1076
B1077
B1078
B1079
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст