Nissan Juke (2012 year). Service Repair Manual — part 210
SRC-70
< DTC/CIRCUIT DIAGNOSIS >
B1080, B1096 DRIVER AIR BAG MODULE
B1080, B1096 DRIVER AIR BAG MODULE
DTC Logic
INFOID:0000000007578287
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578288
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
CHECK SPIRAL CABLE CIRCUIT-I
1.
Turn ignition switch OFF.
2.
Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.
3.
Check continuity between combination switch (spiral cable) terminals.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1080
B1096
DRIVER AIRBAG
MODULE
[SHORT]
Driver air bag module circuit are shorted to each
other
(including the spiral cable)
• Harness or connectors
(The module circuit is shorted.)
• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1080, B1096 DRIVER AIR BAG MODULE
SRC-71
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace combination switch (spiral cable). Refer to
SR-13, "Removal and Installation"
.
4.
CHECK SPIRAL CABLE CIRCUIT-II
Check continuity between combination switch (spiral cable) terminals.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace combination switch (spiral cable). Refer to
SR-13, "Removal and Installation"
.
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 6.
NO
>> INSPECTION END
6.
REPLACE DRIVER AIR BAG MODULE
1.
Replace driver air bag module. Refer to
SR-10, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Combination switch (spiral cable)
Continuity
Connector
Terminal
Connector
Terminal
M301
10
M301
11
Not existed
M300
9
12
Combination switch (spiral cable)
Continuity
Connector
Terminal
Terminal
M32
28
29
Not existed
30
Revision: 2011 October
2012 JUKE
SRC-72
< DTC/CIRCUIT DIAGNOSIS >
B1081 SEAT BELT PRE-TENSIONER RH
B1081 SEAT BELT PRE-TENSIONER RH
DTC Logic
INFOID:0000000007578289
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578290
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SEAT BELT PRE-TENSIONER
1.
Replace seat belt pre-tensioner RH. Refer to
SR-29, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1081
PRE-TEN FRONT RH
[OPEN]
Seat belt pre-tensioner RH circuit is open
• Harness or connectors
(The pre-tensioner circuit is open.)
• Malfunction in seat belt pre-tensioner RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1081 SEAT BELT PRE-TENSIONER RH
SRC-73
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
SRC-74
< DTC/CIRCUIT DIAGNOSIS >
B1082 SEAT BELT PRE-TENSIONER RH
B1082 SEAT BELT PRE-TENSIONER RH
DTC Logic
INFOID:0000000007578291
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578292
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SEAT BELT PRE-TENSIONER
1.
Replace seat belt pre-tensioner RH. Refer to
SR-29, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1082
PRE-TEN FRONT RH
[VB-SHORT]
Seat belt pre-tensioner RH circuit is
shorted to power supply circuit
• Harness or connectors
(The pre-tensioner circuit is shorted.)
• Malfunction in seat belt pre-tensioner RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1082 SEAT BELT PRE-TENSIONER RH
SRC-75
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
SRC-76
< DTC/CIRCUIT DIAGNOSIS >
B1083 SEAT BELT PRE-TENSIONER RH
B1083 SEAT BELT PRE-TENSIONER RH
DTC Logic
INFOID:0000000007578293
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578294
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SEAT BELT PRE-TENSIONER
1.
Replace seat belt pre-tensioner RH. Refer to
SR-29, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1083
PRE-TEN FRONT RH
[GND-SHORT]
Seat belt pre-tensioner RH circuit is
shorted to ground
• Harness or connectors
(The pre-tensioner circuit is shorted.)
• Malfunction in seat belt pre-tensioner RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1083 SEAT BELT PRE-TENSIONER RH
SRC-77
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
SRC-78
< DTC/CIRCUIT DIAGNOSIS >
B1084 SEAT BELT PRE-TENSIONER RH
B1084 SEAT BELT PRE-TENSIONER RH
DTC Logic
INFOID:0000000007578295
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578296
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SEAT BELT PRE-TENSIONER
1.
Replace seat belt pre-tensioner RH. Refer to
SR-29, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1084
PRE-TEN FRONT RH
[SHORT]
Seat belt pre-tensioner RH circuits are
shorted to each other
• Harness or connectors
(The pre-tensioner circuit is shorted.)
• Malfunction in seat belt pre-tensioner RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1084 SEAT BELT PRE-TENSIONER RH
SRC-79
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
SRC-80
< DTC/CIRCUIT DIAGNOSIS >
B1086 SEAT BELT PRE-TENSIONER LH
B1086 SEAT BELT PRE-TENSIONER LH
DTC Logic
INFOID:0000000007578297
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578298
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SEAT BELT PRE-TENSIONER
1.
Replace seat belt pre-tensioner LH. Refer to
SR-29, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1086
PRE-TEN FRONT LH
[OPEN]
Seat belt pre-tensioner LH circuit is open
• Harness or connectors
(The pre-tensioner circuit is open.)
• Malfunction in seat belt pre-tensioner LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1086 SEAT BELT PRE-TENSIONER LH
SRC-81
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
SRC-82
< DTC/CIRCUIT DIAGNOSIS >
B1087 SEAT BELT PRE-TENSIONER LH
B1087 SEAT BELT PRE-TENSIONER LH
DTC Logic
INFOID:0000000007578299
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578300
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SEAT BELT PRE-TENSIONER
1.
Replace seat belt pre-tensioner LH. Refer to
SR-29, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1087
PRE-TEN FRONT LH
[VB-SHORT]
Seat belt pre-tensioner LH circuit is
shorted to power supply circuit
• Harness or connectors
(The pre-tensioner circuit is shorted.)
• Malfunction in seat belt pre-tensioner LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1087 SEAT BELT PRE-TENSIONER LH
SRC-83
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
SRC-84
< DTC/CIRCUIT DIAGNOSIS >
B1088 SEAT BELT PRE-TENSIONER LH
B1088 SEAT BELT PRE-TENSIONER LH
DTC Logic
INFOID:0000000007578301
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-11, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007578302
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SEAT BELT PRE-TENSIONER
1.
Replace seat belt pre-tensioner LH. Refer to
SR-29, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1088
PRE-TEN FRONT LH
[GND-SHORT]
Seat belt pre-tensioner LH circuit is
shorted to ground
• Harness or connectors
(The pre-tensioner circuit is shorted.)
• Malfunction in seat belt pre-tensioner LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2011 October
2012 JUKE
B1088 SEAT BELT PRE-TENSIONER LH
SRC-85
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст