Nissan Juke (2012 year). Service Repair Manual — part 196
B2556 PUSH-BUTTON IGNITION SWITCH
SEC-53
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-80, "Removal and Installation"
.
2.
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
>> INSPECTION END
4.
CHECK PUSH-BUTTON IGNITION SWITCH GROUND CIRCUIT
Check continuity between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK PUSH-BUTTON IGNITION SWITCH
SEC-53, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace push-button ignition switch. Refer to
SEC-117, "Removal and Installation"
.
6.
CHECK INTERMITTENT INCIDENT
GI-43, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000007579690
1.
CHECK PUSH-BUTTON IGNITION SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect push-button ignition switch connector.
3.
Check continuity between push-button ignition switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace push-button ignition switch. Refer to
SEC-117, "Removal and Installation"
.
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M101
4
Existed
Push-button ignition switch
Condition
Continuity
Terminal
8
4
Push-button ignition
switch
Pressed
Existed
Not pressed
Not existed
Revision: 2011 October
2012 JUKE
SEC-54
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2557 VEHICLE SPEED
B2557 VEHICLE SPEED
DTC Logic
INFOID:0000000007579691
DTC DETECTION LOGIC
NOTE:
• If DTC B2557 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2557 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and wait 10 seconds or more.
2.
Drive the vehicle at a vehicle speed of 10 km/h (6.2 MPH) or more for 10 seconds or more.
3.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007579692
1.
CHECK DTC OF “ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)”
Check DTC in “Self Diagnostic Result” mode of “ABS” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
.
NO
>> GO TO 2.
2.
CHECK DTC OF “COMBINATION METER”
Check DTC in “Self Diagnostic Result” mode of “METER/M&A” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK INTERMITTENT INCIDENT
GI-43, "Intermittent Incident"
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible causes
B2557
VEHICLE SPEED
BCM detects one of the following conditions for 10
seconds continuously.
• Vehicle speed signal from combination meter is 10
km/h (6.2 MPH) or more, and vehicle speed signal
from ABS actuator and electric unit (control unit) is
4 km/h (2.5 MPH) or less.
• Vehicle speed signal from combination meter is 4
km/h (2.5 MPH) or less, and vehicle speed signal
from ABS actuator and electric unit (control unit) is
10 km/h (6.2 MPH) or more.
• Harness or connectors
(The CAN communication line is
open or shorted.)
• Combination meter
• ABS actuator and electric unit
(control unit)
Revision: 2011 October
2012 JUKE
B2601 SHIFT POSITION
SEC-55
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2601 SHIFT POSITION
DTC Logic
INFOID:0000000007579693
DTC DETECTION LOGIC
NOTE:
• If DTC B2601 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2601 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Shift the selector lever to the P position.
2.
Turn ignition switch ON and wait 2 seconds or more.
3.
Shift the selector lever to any position other than P, and wait 2 seconds or more.
4.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007579694
1.
CHECK CVT SHIFT SELECTOR POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect CVT shift selector (detention switch) connector.
3.
Check voltage between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK CVT SHIFT SELECTOR POWER SUPPLY CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between CVT shift selector (detention switch) harness connector and BCM harness con-
nector.
3.
Check continuity between CVT shift selector (detention switch) harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2601
SHIFT POSITION
When there is a difference between P range
signal from CVT shift selector (detention
switch) and P position signal from IPDM E/R
(CAN).
• Harness or connectors
(CAN communication line is open or
shorted.)
• Harness or connectors
[CVT shift selector (detention switch)
circuit is open or shorted.]
• BCM
• IPDM E/R
(+)
(–)
Voltage (V)
(Approx.)
CVT shift selector (detention switch)
Connector
Terminal
M57
12
Ground
12
CVT shift selector (detention switch)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M57
12
M70
104
Existed
Revision: 2011 October
2012 JUKE
SEC-56
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2601 SHIFT POSITION
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-80, "Removal and Installation"
.
2.
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
>> INSPECTION END
4.
CHECK CVT SHIFT SELECTOR CIRCUIT (IPDM E/R)
1.
Disconnect IPDM E/R connector.
2.
Check continuity between CVT shift selector (detention switch) harness connector and IPDM E/R harness
connector.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK CVT SHIFT SELECTOR CIRCUIT (BCM)
1.
Disconnect BCM connector.
2.
Check continuity between CVT shift selector (detention switch) harness connector and BCM harness con-
nector.
3.
Check continuity between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-80, "Removal and Installation"
.
2.
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
3.
Perform DTC CONFIRMATION PROCEDURE for DTC B2601. Refer to
Is DTC B2601 detected again?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
NO
>> INSPECTION END
CVT shift selector (detention switch)
Ground
Continuity
Connector
Terminal
M57
12
Not existed
CVT shift selector (detention switch)
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
M57
13
E17
64
Existed
CVT shift selector (detention switch)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M57
13
M68
37
Existed
CVT shift selector (detention switch)
Ground
Continuity
Connector
Terminal
M57
13
Not existed
Revision: 2011 October
2012 JUKE
B2602 SHIFT POSITION
SEC-57
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2602 SHIFT POSITION
DTC Logic
INFOID:0000000007579695
DTC DETECTION LOGIC
NOTE:
• If DTC B2602 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2602 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine.
2.
Drive vehicle at a speed of 4 km/h (2.5 MPH) or more for 10 seconds or more.
3.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007579696
1.
CHECK DTC OF “ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)”
Check DTC in “Self Diagnostic Result” mode of “ABS” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
.
NO
>> GO TO 2.
2.
CHECK DTC OF COMBINATION METER
Check DTC in “Self Diagnostic Result” mode of “METER/M&A” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK CVT SHIFT SELECTOR POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect CVT shift selector (detention switch) connector.
3.
Check voltage between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2602
SHIFT POSITION
BCM detects the following status for 10 seconds.
• Selector lever is in the P position
• Vehicle speed is 4 km/h (2.5 MPH) or more
• Ignition switch is in the ON position
• Harness or connectors
(CAN communication line is open or
shorted.)
• Harness or connectors
[CVT shift selector (detention switch)
circuit is open or shorted.]
• CVT shift selector (detention switch)
• Combination meter
• BCM
(+)
(–)
Voltage (V)
(Approx.)
CVT shift selector (detention switch)
Connector
Terminal
M57
12
Ground
12
Revision: 2011 October
2012 JUKE
SEC-58
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2602 SHIFT POSITION
NO
>> GO TO 4.
4.
CHECK CVT SHIFT SELECTOR POWER SUPPLY CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between CVT shift selector (detention switch) harness connector and BCM harness con-
nector.
3.
Check continuity between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-80, "Removal and Installation"
.
2.
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
>> INSPECTION END
6.
CHECK CVT SHIFT SELECTOR CIRCUIT
1.
Disconnect BCM connector and IPDM E/R connector.
2.
Check continuity between CVT shift selector (detention switch) harness connector and BCM harness con-
nector.
3.
Check continuity between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
CHECK CVT SHIFT SELECTOR (DETENTION SWITCH)
SEC-59, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Replace CVT shift selector. Refer to
TM-212, "Removal and Installation"
8.
CHECK INTERMITTENT INCIDENT
GI-43, "Intermittent Incident"
>> INSPECTION END
CVT shift selector (detention switch)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M57
12
M70
104
Existed
CVT shift selector (detention switch)
Ground
Continuity
Connector
Terminal
M57
12
Not existed
CVT shift selector (detention switch)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M57
13
M68
37
Existed
CVT shift selector (detention switch)
Ground
Continuity
Connector
Terminal
M57
13
Not existed
Revision: 2011 October
2012 JUKE
B2602 SHIFT POSITION
SEC-59
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Component Inspection
INFOID:0000000007579697
1.
CHECK CVT SHIFT SELECTOR (DETENTION SWITCH)
1.
Turn ignition switch OFF.
2.
Disconnect CVT shift selector connector.
3.
Check continuity between CVT shift selector (detention switch) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace CVT shift selector. Refer to
TM-212, "Removal and Installation"
CVT shift selector (detention switch)
Condition
Continuity
Terminal
12
13
Selector lever: P position
Selector button: Released
Not existed
Selector button: Pressed
Existed
Selector lever: Except P position
Revision: 2011 October
2012 JUKE
SEC-60
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2603 SHIFT POSITION
B2603 SHIFT POSITION
DTC Logic
INFOID:0000000007579698
DTC DETECTION LOGIC
NOTE:
• If DTC B2603 is displayed with DTC B2601, first perform the trouble diagnosis for DTC B2601. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE 1
1.
Shift the selector lever to the P position.
2.
Turn ignition switch ON and wait 1 second or more.
3.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE 2
1.
Shift the selector lever to any position other than P, and wait 1 second or more.
2.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007579699
1.
INSPECTION START
Perform inspection in accordance with procedure that confirms DTC.
Which procedure confirms DTC?
DTC confirmation procedure 1>>GO TO 2.
DTC confirmation procedure 2>>GO TO 8.
2.
CHECK FUSE
1.
Turn power switch OFF.
2.
Check that the following fuse in IPDM E/R is not blown.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the blown fuse after repairing the cause of blowing.
3.
CHECK TRANSMISSION RANGE SWITCH POWER SUPPLY
1.
Disconnect transmission range switch connector.
2.
Turn ignition switch ON.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible causes
B2603
SHIFT POSI STATUS
BCM detects the following status when ignition
switch is in the ON position.
• Transmission range switch signal: approx. 0 V
• CVT shift selector (detention switch) signal:
approx. 0 V
• Harness or connector
[CVT shift selector (detention switch)
circuit is open or shorted.]
• Harness or connectors
(Transmission range switch circuit is
open or shorted.)
• CVT shift selector (detention switch)
• Transmission range switch
• BCM
Signal name
Fuse No.
Ignition power supply
56 (10 A)
Revision: 2011 October
2012 JUKE
B2603 SHIFT POSITION
SEC-61
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
3.
Check voltage between transmission range switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK TRANSMISSION RANGE SWITCH POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between transmission range switch harness connector and IPDM E/R harness connec-
tor.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
NO
>> Repair or replace harness.
5.
CHECK BCM INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Connect transmission range switch harness connector.
3.
Turn ignition switch ON.
4.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> GO TO 6.
6.
CHECK BCM INPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect transmission range switch connector.
3.
Disconnect BCM connector.
4.
Check continuity between transmission range switch harness connector and BCM harness connector.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
CHECK TRANSMISSION RANGE SWITCH
SEC-63, "Component Inspection (Transmission Range Switch)"
.
Is the inspection result normal?
(+)
(–)
Voltage (V)
Transmission range switch
Connector
Terminal
F27
1
Ground
6 - 16
Transmission range switch
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F27
1
E15
58
Existed
(+)
(–)
Condition
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M70
102
Ground
Selector lever
P or N position
Battery voltage
Other than above
0
Transmission range switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
F27
2
M70
102
Existed
Revision: 2011 October
2012 JUKE
SEC-62
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2603 SHIFT POSITION
YES
>> GO TO 12.
NO
>> Replace transmission range switch. Refer to
TM-221, "Removal and Installation"
.
8.
CHECK CVT SHIFT SELECTOR POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect CVT shift selector (detention switch) connector.
3.
Check voltage between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> GO TO 9.
9.
CHECK CVT SHIFT SELECTOR POWER SUPPLY CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between CVT shift selector (detention switch) harness connector and BCM harness con-
nector.
3.
Check continuity between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> Repair or replace harness.
10.
CHECK CVT SHIFT SELECTOR CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between CVT shift selector (detention switch) harness connector and BCM harness con-
nector.
3.
Check continuity between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Repair or replace harness.
11.
CHECK CVT SHIFT SELECTOR (DETENTION SWITCH)
SEC-63, "Component Inspection [CVT Shift Selector (Detention Switch)]"
.
Is the inspection result normal?
(+)
(–)
Voltage (V)
(Approx.)
CVT shift selector (detention switch)
Connector
Terminal
M57
12
Ground
12
CVT shift selector (detention switch)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M57
12
M70
104
Existed
CVT shift selector (detention switch)
Ground
Continuity
Connector
Terminal
M57
12
Not existed
CVT shift selector (detention switch)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M57
13
M68
37
Existed
CVT shift selector (detention switch)
Ground
Continuity
Connector
Terminal
M57
13
Not existed
Revision: 2011 October
2012 JUKE
B2603 SHIFT POSITION
SEC-63
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
YES
>> GO TO 13.
NO
>> Replace CVT shift selector. Refer to
TM-212, "Removal and Installation"
12.
CHECK INTERMITTENT INCIDENT
GI-43, "Intermittent Incident"
.
>> INSPECTION END
13.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-80, "Removal and Installation"
.
2.
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
>> INSPECTION END
Component Inspection (Transmission Range Switch)
INFOID:0000000007579700
1.
CHECK TRANSMISSION RANGE SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect transmission range switch connector.
3.
Check continuity between transmission range switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace transmission range switch. Refer to
TM-221, "Removal and Installation"
.
Component Inspection [CVT Shift Selector (Detention Switch)]
INFOID:0000000007579701
1.
CHECK CVT SHIFT SELECTOR (DETENTION SWITCH)
1.
Turn ignition switch OFF.
2.
Disconnect CVT shift selector connector.
3.
Check continuity between CVT shift selector (detention switch) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace CVT shift selector. Refer to
TM-212, "Removal and Installation"
Transmission range switch
Condition
Continuity
Terminal
1
2
P or N position
Existed
Other than above
Not existed
CVT shift selector (detention switch)
Condition
Continuity
Terminal
12
13
Selector lever: P position
Selector button: Released
Not existed
Selector button: Pressed
Existed
Selector lever: Except P position
Revision: 2011 October
2012 JUKE
SEC-64
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2604 SHIFT POSITION
B2604 SHIFT POSITION
DTC Logic
INFOID:0000000007579702
DTC DETECTION LOGIC
NOTE:
• If DTC B2604 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2604 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Shift the selector lever to the P position.
2.
Turn ignition switch ON and wait 5 seconds or more.
3.
Shift the selector lever to the N position and wait 5 seconds or more.
4.
Shift the selector lever to any position other than P and N, and wait 5 seconds or more.
5.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007579703
1.
CHECK DTC OF TCM
Check DTC in “Self Diagnostic Result” mode of “TCM” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
.
NO
>> GO TO 2.
2.
CHECK BCM INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-80, "Removal and Installation"
.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2604
PNP/CLUTCH SW
The following states are detected for 5 seconds
while ignition switch is ON.
• P/N position signal is sent from transmission
range switch but shift position signal input
(CAN) from TCM is other than P and N
• P/N position signal is not sent from transmis-
sion range switch but shift position signal input
(CAN) from TCM is P or N
• Harness or connectors
(CAN communication line is open
or shorted.)
• Harness or connectors
(Transmission range switch circuit
is open or shorted.)
• Transmission range switch
• TCM
• BCM
(+)
(–)
Condition
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M70
102
Ground
Selector lever
P or N position
Battery voltage
Other than above
0
Revision: 2011 October
2012 JUKE
B2604 SHIFT POSITION
SEC-65
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
2.
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
>> INSPECTION END
4.
CHECK BCM INPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect transmission range switch connector.
3.
Disconnect BCM connector.
4.
Check continuity between transmission range switch harness connector and BCM harness connector.
5.
Check continuity between transmission range switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK INTERMITTENT INCIDENT
GI-43, "Intermittent Incident"
.
>> INSPECTION END
Transmission range switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
F27
2
M70
102
Existed
Transmission range switch
Ground
Continuity
Connector
Terminal
F27
2
Not existed
Revision: 2011 October
2012 JUKE
SEC-66
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2605 SHIFT POSITION
B2605 SHIFT POSITION
DTC Logic
INFOID:0000000007579704
DTC DETECTION LOGIC
NOTE:
• If DTC B2605 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2605 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Shift the selector lever to the P position.
2.
Turn ignition switch ON and wait 1 second or more.
3.
Shift the selector lever to the N position and wait 1 second or more.
4.
Shift the selector lever to any position other than P and N, and wait 1 second or more.
5.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007579705
1.
CHECK IPDM E/R INPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Disconnect BCM connector.
4.
Check continuity between IPDM E/R harness connector and BCM harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-80, "Removal and Installation"
.
2.
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
3.
Perform DTC CONFIRMATION PROCEDURE for B2605. Refer to
.
Is DTC B2605 detected again?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
NO
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2605
PNP/CLUTCH SW
When ignition switch is ON, P/N position
signal input from transmission range switch
and P/N position signal input (CAN) from
IPDM E/R do not match.
• Harness or connectors
(CAN communication line is open or
shorted.)
• Harness or connectors
(Transmission range switch circuit is
open or shorted.)
• Transmission range switch
• IPDM E/R
• BCM
IPDM E/R
BCM
Continuity
Connector
Terminal
Connector
Terminal
E15
48
M70
102
Existed
Revision: 2011 October
2012 JUKE
B2608 STARTER RELAY
SEC-67
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2608 STARTER RELAY
DTC Logic
INFOID:0000000007579706
DTC DETECTION LOGIC
NOTE:
• If DTC B2608 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2608 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
• If DTC B2608 is displayed with DTC B210D (IPDM E/R), first perform the trouble diagnosis for DTC B210D.
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Press push-button ignition switch under the following conditions to start engine.
CVT models
-
Selector lever: In the P position
-
Brake pedal: Depressed
M/T models
-
Shift lever: In the Nuetral position
-
Clutch pedal: Depressed
2.
Wait 1 second after engine started.
3.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007579707
1.
CHECK DTC OF IPDM E/R
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK STARTER RELAY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Disconnect BCM connector.
4.
Check continuity between IPDM E/R harness connector and BCM harness connector.
5.
Check continuity between IPDM E/R harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2608
STARTER RELAY
BCM outputs starter relay OFF signal but
BCM receives starter relay ON signal from
IPDM E/R (CAN).
• Harness or connectors
(CAN communication line is open or
shorted.)
• Harness or connectors
(Starter relay circuit is open or shorted.)
• IPDM E/R
IPDM E/R
BCM
Continuity
Connector
Terminal
Connector
Terminal
E13
30
M70
97
Existed
Revision: 2011 October
2012 JUKE
SEC-68
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2608 STARTER RELAY
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
REPLACE IPDM E/R
1.
Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
2.
Perform DTC CONFIRMATION PROCEDURE for DTC B2608. Refer to
Is DTC B2608 detected again?
YES
>> INSPECTION END
NO
>> GO TO 4.
4.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-80, "Removal and Installation"
.
2.
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
>> INSPECTION END
IPDM E/R
Ground
Continuity
Connector
Terminal
E13
30
Not existed
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст