Nissan Juke (2012 year). Service Repair Manual — part 17
BCS
SYSTEM
BCS-91
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Sleep condition
NOTE:
*: Refer to
INL-8, "INTERIOR ROOM LAMP BATTERY SAVER SYSTEM : System Description"
for details of
the interior room lamp battery saver time.
Wake-up operation
• BCM transmits sleep wake up signal (wake up) to each unit when any condition listed below is established,
and then goes into normal mode from low power consumption mode.
• Each unit starts transmissions with CAN communication by receiving sleep wake up signals. Each unit trans-
mit wake up signals to BCM with CAN communication to convey the start of CAN communication.
Wake-up condition
CAN sleep condition
BCM sleep condition
• Receiving the sleep-ready signal (ready) from all units
• 1 minute after turning ignition switch OFF
• Theft warning alarm and panic alarm: Not operation
• Warning chime: Not operation
• Stop lamp switch: OFF
• Turn signal indicator lamp: Not operation
• Exterior lamp: OFF
• Door lock status: No change
• CONSULT communication status: Not communication
• Door switch status: No change
• Key switch status: No change
• Interior room lamp battery saver: Time out*
• RAP system: No communication
• Nissan anti-theft system (NATS): Not operation
• Remote keyless entry receiver communication status: No com-
munication
• Tire pressure monitoring system (TPMS): Stop
BCM wake-up condition
CAN wake-up condition
Back door opener switch: OFF
→
ON
• Receiving the sleep-ready signal (Not-ready) from any units
• Ignition switch: OFF
→
ACC, ON
• Key switch: OFF
→
ON, ON
→
OFF
• Hazard switch: ON
• HI BEAM switch: OFF
→
ON, ON
→
OFF
• PASSING switch: OFF
→
ON, ON
→
OFF
• HEADLAMP 1 switch: OFF
→
ON, ON
→
OFF
• HEADLAMP 2 switch: OFF
→
ON, ON
→
OFF
• TAIL LAMP switch: OFF
→
ON
• FR FOG switch: OFF
→
ON, ON
→
OFF
• TURN RH: OFF
→
ON, ON
→
OFF
• TURN LH: OFF
→
ON, ON
→
OFF
• Driver door switch: OFF
→
ON, ON
→
OFF
• Passenger door switch: OFF
→
ON, ON
→
OFF
• Rear RH door switch: OFF
→
ON, ON
→
OFF
• Rear LH door switch: OFF
→
ON, ON
→
OFF
• Back door switch: OFF
→
ON, ON
→
OFF
• Stop lamp switch: ON
• Door lock and unlock switch: NEUTRAL
→
LOCK, NEUTRAL
→
UNLOCK
• Front door lock assembly (driver side) (unlock sensor): OFF
→
ON, ON
→
OFF
• Front door lock assembly (driver side) (door key cylinder switch):
NEUTRAL
→
LOCK, NEUTRAL
→
UNLOCK
• Remote keyless entry receiver communication: Receiving
Revision: 2011 October
2012 JUKE
BCS-92
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000007576701
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
DOOR LOCK
DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)
INFOID:0000000007829421
WORK SUPPORT
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp control
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
Air conditioning system
AIR CONDITONER
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
×
Signal buffer system
SIGNAL BUFFER
×
×
Panic alarm
PANIC ALARM
×
TPMS
AIR PRESSUE MONITOR
×
×
×
Revision: 2011 October
2012 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-93
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*: P range interlock door lock/unlock can be selected for M/T models, but automatic door lock/unlock function does not operate.
DATA MONITOR
ACTIVE TEST
Monitor item
Description
DOOR LOCK-UNLOCK SET
Anti-hijack function can be changed to operate with this mode
• On: Operate
• Off: Non-operation
AUTOMATIC DOOR LOCK SE-
LECT
Automatic door lock function can be selected from the following in this mode
• VH SPD: All doors are locked when vehicle speed more than 24km/h (15MPH)
• P RANGE*: All doors are locked when shifting the selector lever from P position to other
than the P position
AUTOMATIC DOOR UNLOCK
SELECT
Automatic door unlock function can be selected from the following in the mode
• MODE 1: All doors are unlocked when the power supply position is changed from ON to
OFF
• MODE 2*: All doors are unlocked when shifting the selector lever from any position other
than the P to P position
• MODE 3: Driver side door is unlocked when the power supply position is changed from ON
to OFF
• MODE 4*: Driver side door is unlocked when shifting the selector lever from any position
other than the P to P position
• MODE 5: Driver side door is unlocked when key out of key switch
• MODE 6: All doors are unlocked when key out of key switch
AUTOMATIC LOCK/UNLOCK
SET
Automatic door lock/unlock function can be selected from the following in this mode
• Off: Non-operation
• Unlock Only: Door unlock operation only
• Lock Only: Door lock operation only
• Lock/Unlock: Door lock and unlock operation
Monitor Item
Contents
IGN ON SW
Indicated [On/Off] condition of ignition switch in ON position
KEY ON SW
Indicated [On/Off] condition of key switch
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock unlock switch
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicated [On/Off] condition of rear door switch LH
BACK DOOR SW
Indicated [On/Off] condition of back door switch
LOCK STATUS
Indicated [On/Off] condition of front door driver side
ACC ON SW
Indicated [On/Off] condition of ignition switch in ACC position
KEYLESS LOCK
Indicated [On/Off] condition of lock signal from key fob
KEYLESS UNLOCK
Indicated [On/Off] condition of unlock signal from key fob
KEY CYL LK-SW
Indicated [On/Off] condition of lock signal from door key cylinder
KEY CYL UN-SW
Indicated [On/Off] condition of unlock signal from door key cylinder
VEHICLE SPEED
Display the vehicle speed signal received from combination meter by numer-
ical value [Km/h]
Revision: 2011 October
2012 JUKE
BCS-94
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
REAR WINDOW DEFOGGER
REAR WINDOW DEFOGGER : CONSULT Function (BCM - REAR DEFOGGER)
INFOID:0000000007829437
Data monitor
ACTIVE TEST
BUZZER
BUZZER : CONSULT Function (BCM - BUZZER)
INFOID:0000000007829446
CONSULT APPLICATION ITEMS
DATA MONITOR
Test item
Description
DOOR LOCK
This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LCK” on CONSULT screen is touched
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT screen is touched
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT screen is
touched
• The back door lock actuator is unlocked when “BD ULK” on CONSULT screen is touched
• The door lock actuator (other) is unlocked when “OTR ULK” on CONSULT screen is
touched
Monitor Item
Description
REAR DEF SW
Displays “Press (ON)/other (OFF)” status determined with the rear window defogger switch.
IGN ON SW
Indicates [ON/OFF] condition of ignition switch in ON position.
ACC ON SW
Indicates [ON/OFF] condition of ignition switch ACC position.
Test Item
Description
REAR DEFOGGER
Rear window defogger operates when “ON” on CONSULT screen is touched.
Test item
Diagnosis mode
Description
BUZZER
Data Monitor
Displays BCM input data in real time.
Active Test
Operation of electrical loads can be checked by sending driving signal to them.
Display item
[Unit]
Description
IGN ON SW
[On/Off]
Status of ignition switch judged by BCM.
KEY ON SW
[On/Off]
Status of key switch judged by BCM.
DOOR SW-DR
[km/h]
Status of driver side door switch judged by BCM.
REVERSE SW CAN
[On/Off]
This item is displayed, but cannot be monitored.
TAIL LAMP SW
[On/Off]
Status of lighting switch judged by BCM using the combination switch readout function.
FR FOG SW
[On/Off]
Status of front fog lamp switch judged by BCM using the combination switch readout function.
Revision: 2011 October
2012 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-95
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
INT LAMP
INT LAMP : CONSULT Function (BCM - INT LAMP)
INFOID:0000000007829432
WORK SUPPORT
BUCKLE SW
[On/Off]
Status of seat belt buckle switch (driver side) received from combination meter with CAN communica-
tion line.
VEHICLE SPEED
[km/h]
Value of vehicle speed signal received from combination meter with CAN communication line.
Display item
[Unit]
Description
Display item
[Unit]
Description
SEAT BELT WARN TEST
The seat belt warning chime operation can be checked by operating the relevant function (On/Off).
IGN KEY WARN ALM
The key warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM
The light warning chime operation can be checked by operating the relevant function (On/Off).
JPLIA0093GB
Service item
Setting item
Setting
ROOM LAMP TIMER SET
MODE 1
0 sec.
Sets the interior room lamp ON time. (Timer operating time)
MODE 2
7.5 sec.
MODE 3*
15 sec.
MODE 4
30 sec.
SET I/L D-UNLCK INTCON
On*
With the interior room lamp timer function
Off
Without the interior room lamp timer function
ROOM LAMP ON TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual brightening time.
MODE 2*
1 sec.
MODE 3
2 sec.
MODE 4
3 sec.
MODE 5
4 sec.
MODE 6
5 sec.
MODE 7
0 sec.
Revision: 2011 October
2012 JUKE
BCS-96
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*: Factory setting
DATA MONITOR
ACTIVE TEST
ROOM LAMP OFF TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual dimming time.
MODE 2*
1 sec.
MODE 3
2 sec.
MODE 4
3 sec.
MODE 5
4 sec.
MODE 6
5 sec.
MODE 7
0 sec.
R LAMP TIMER LOGIC SET
MODE 1*
Interior room lamp timer activates with synchronizing all doors.
MODE 2
Interior room lamp timer activates with synchronizing the driver door
only.
Service item
Setting item
Setting
Monitor item
[Unit]
Description
IGN ON SW
[On/Off]
Ignition switch (ON) status judeges from IGN signal (ignition power supply)
KEY ON SW
[On/Off]
The switch status input from key switch
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]
The switch status input from rear door switch LH
BACK DOOR SW
[On/Off]
The switch status input from back door switch
LOCK STATUS
[On/Off]
The switch status input from door lock status switch (driver side)
CDL LOCK SW
[On/Off]
Lock switch status input from door lock and unlock switch
CDL UNLOCK SW
[On/Off]
Unlock switch status input from door lock and unlock switch
KEYLESS LOCK
[On/Off]
Lock signal status received from remote keyless entry receiver
KEYLESS UNLOCK
[On/Off]
Unlock signal status received from remote keyless entry receiver
TRNK/HAT MNTR
[On/Off]
NOTE:
The item is indicated, but not monitored
KEY CYL LK-SW
[On/Off]
Lock switch status received from key cylinder switch
KEY CYL UN-SW
[On/Off]
Unlock switch status received from key cylinder switch
ACC ON SW
[On/Off]
Ignition switch (ACC) status judges from ACC signal (ACC power supply)
Revision: 2011 October
2012 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-97
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
MULTI REMOTE ENT
MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT)
INFOID:0000000007829422
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
Test item
Operation
Description
INT LAMP
On
Outputs the interior room lamp control signal to turn the interior room lamps ON.
[Map lamp, room lamp (when applicable lamps switch is in DOOR position.)]
Off
Stops the interior room lamp control signal to turn the interior room lamps.
Monitor Item
Condition
IGN ON SW
Indicates [On/Off] condition of ignition switch in ON position
KEY ON SW
Indicates [On/Off] condition of key switch
ACC ON SW
Indicates [On/Off] condition of ignition switch in ACC position
KEYLESS LOCK
Indicates [On/Off] condition of lock signal from keyfob
KEYLESS UNLOCK
Indicates [On/Off] condition of unlock signal from keyfob
KYLS TRNK/HAT
NOTE:
This item is displayed, but cannot be tested
DOOR SW-DR
Indicates [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicates [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicates [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicates [On/Off] condition of rear door switch LH
BACK DOOR SW
Indicates [On/Off] condition of back door switch
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be tested
CDL LOCK SW
Indicates [On/Off] condition of door lock and unlock switch
CDL UNLOCK SW
Indicates [On/Off] condition of door lock and unlock switch
KEYLESS PANIC
Indicates [On/Off] condition of PANIC button of keyfob
Test item
Description
INT LAMP
This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation
FLASHER
This test is able to check flasher operation [LH/RH/Off]
HORN
This test is able to check horn operation
• On: Operate
Test item
Description
REMO CONT IN REGIST
Keyfob ID code can be registered
REMO CONT IN ERASUR
Keyfob ID code can be erased
REMO CONT IN CONFIR
It can be checked whether Intelligent Key ID code is registered or not in this mode
HORN CHIRP SET
Hazard and horn reminder function (horn operation) mode can be changed in this mode
• On: Operate
• Off: Non-operation
Revision: 2011 October
2012 JUKE
BCS-98
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEAD LAMP)
INFOID:0000000007829428
WORK SUPPORT
HAZARD LAMP SET
Hazard and horn reminder function (hazard operation) mode can be changed in this mode
• MODE1: Non-operation
• MODE2: Unlock operation only
• MODE3: Lock operation only
• MODE4: Lock and unlock operation
AUTO LOCK SET
Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute
PANIC ALARM SET
Panic alarm button pressing time on keyfob remote control button can be selected from the
following with this mode
• MODE1: 0.5 sec
• MODE2: Non-operation
• MODE3: 1.5 sec
TRUNK OPEN SET
NOTE:
This item is displayed, but cannot be tested
Test item
Description
Service item
Setting item
Setting
CUSTOM A/LIGHT SET-
TING*
1
MODE 1*
2
Normal
MODE 2
More sensitive setting than normal setting (Turns ON earlier than normal opera-
tion)
MODE 3
More sensitive setting than MODE 2 (Turns ON earlier than MODE 2)
MODE 4
Less sensitive setting than normal setting (Turns ON later than normal operation)
BATTERY SAVER SET
On*
2
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
ILL DELAY SET*
1
MODE 1*
2
45 sec.
Sets delay timer function timer operation time
(All doors closed)
MODE 2
Without the
function
MODE 3
30 sec.
MODE 4
60 sec.
MODE 5
90 sec.
MODE 6
120 sec.
MODE 7
150 sec.
MODE 8
180 sec.
HEAD LIGHT TIMER
MODE 1
10 sec.
Sets follow me home function activating time
MODE 2
*2
30 sec.
Revision: 2011 October
2012 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-99
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*
1
: For models without auto light system, this item is displayed but is not operated.
*
2
: Factory setting
DATA MONITOR
AUTO LIGHT LOGIC SET*
1
MODE 1*
2
With twilight ON custom & with wiper INT, LO and HI
MODE 2
With twilight ON custom & with wiper LO and HI
MODE 3
With twilight ON custom & without
MODE 4
Without twilight ON custom & with wiper INT, LO and HI
MODE 5
Without twilight ON custom & with wiper LO and HI
MODE 6
Without twilight ON custom & without
Service item
Setting item
Setting
Monitor item
[Unit]
Description
PUSH SW
[On/Off]
The switch status input from push-button ignition switch
ENGINE STATE
[Stop/Stall/Crank/Run]
The engine status received from ECM via CAN communication
VEH SPEED 1
[km/h]
The value of the vehicle speed received from combination meter via CAN communi-
cation
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW*
1
[On/Off]
FR FOG SW*
2
[On/Off]
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]
The switch status input from rear door switch LH
DOOR SW-BK
[On/Off]
The switch status input from back door switch
OPTICAL SENSOR
[On/Off/NG]
NOTE:
This item is indicated, but can not monitored
Revision: 2011 October
2012 JUKE
BCS-100
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*
1
: For models without auto light system, this item is not displayed.
*
2
: For models without front fog lamp, this item is displayed but is not monitored.
ACTIVE TEST
*
1
: For models without front fog lamp, this item is displayed but is not tested.
*
2
: For models without daytime running light system, this item is not displayed.
WIPER
WIPER : CONSULT Function (BCM - WIPER)
INFOID:0000000007829435
WORK SUPPORT
*: Factory setting
DATA MONITOR
OPTI SEN (DTCT)*
1
[V]
The value of outside brightness voltage input from the optical sensor
OPTI SEN (FILT)*
1
[V]
The value of outside brightness voltage filtered by BCM
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
On
Transmits the position light request signal to IPDM E/R via CAN commu-
nication to turn the tail lamp ON
Off
Stops the tail lamp request signal transmission
HEAD LAMP
Hi
Transmits the high beam request signal via CAN communication to turn
the headlamp (HI)
Lo
Transmits the low beam request signal via CAN communication to turn
the headlamp (LO)
Off
Stops the high & low beam request signal transmission
FR FOG LAMP*
1
On
Transmits the front fog lights request signal to IPDM E/R via CAN com-
munication to turn the front fog lamp ON
Off
Stops the front light request signal transmission
DAYTIME RUNNING LIGHT*
2
On
Transmits the daytime running light request signal via CAN communica-
tion to IPDM E/R
Off
Stop the daytime running light request signal transmission
ILL DIM SIGNAL
On
NOTE:
This item is indicated, but can not tested
Off
Service item
Setting item
Description
WIPER SPEED
SETTING
On
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
Off*
Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)
Monitor Item
[Unit]
Description
IGN ON SW
[On/Off]
Ignition switch ON status judged from ignition power supply.
IGN SW CAN
[On/Off]
Ignition switch ON status received from IPDM E/R with CAN communication.
Revision: 2011 October
2012 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-101
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER)
INFOID:0000000007829429
WORK SUPPORT
*: Factory setting
DATA MONITOR
FR WIPER HI
[On/Off]
Each switch status that BCM judges from the combination switch reading function.
FR WIPER LOW
[On/Off]
FR WIPER INT
[On/Off]
FR WASHER SW
[On/Off]
INT VOLUME
[1
−
7]
Each switch status that BCM judges from the combination switch reading function.
FR WIPER STOP
[On/Off]
Front wiper motor (stop position) status received from IPDM E/R with CAN communication.
VEHICLE SPEED
[km/h]
The value of the vehicle speed signal received from combination meter with CAN communication.
RR WIPER ON
[On/Off]
Each switch status that BCM judges from the combination switch reading function.
RR WIPER INT
[On/Off]
RR WASHER SW
[On/Off]
RR WIPER STOP
[On/Off]
Rear wiper motor (stop position) status input from the rear wiper motor.
REVERSE SW CAN
[On/Off]
Reverse position status as judged from TCM with CAN communication.
Monitor Item
[Unit]
Description
Test item
Operation
Description
FR WIPER
Hi
Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to
operate the front wiper HI operation.
Lo
Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
operate the front wiper LO operation.
INT
Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
operate the front wiper INT operation.
Off
Stops transmitting the front wiper request signal to stop the front wiper operation.
RR WIPER
On
Outputs the voltage to operate the rear wiper motor.
Off
Stops the voltage to stop.
Service item
Setting item
Setting
HAZARD ANSWER
BACK
Lock Only
With locking only
Sets the hazard warning lamp answer back function
when the door is lock/unlock with the request switch or
the Intelligent Key.
Unlk Only
With unlocking only
Lock&Unlk
*
With locking/unlocking
Off
Without the function
Revision: 2011 October
2012 JUKE
BCS-102
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
AIR CONDITIONER
AIR CONDITIONER : CONSULT Function (BCM - AIR CONDITIONER) (Manual A/C)
INFOID:0000000007829439
DATA MONITOR
Display item list
ACTIVE TEST
COMB SW
COMB SW : CONSULT Function (BCM - COMB SW)
INFOID:0000000007576711
DATA MONITOR
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
The switch status input from the request switch (driver side)
REQ SW-AS
[On/Off]
The switch status input from the request switch (passenger side)
PUSH SW
[On/Off]
The switch status input from the push-button ignition switch
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
[On/Off]
The switch status input from the hazard switch
RKE-LOCK
[On/Off]
Lock signal status received from the remote keyless entry receiver
RKE-UNLOCK
[On/Off]
Unlock signal status received from the remote keyless entry receiver
RKE-PANIC
[On/Off]
Panic alarm signal status received from the remote keyless entry receiver
Test item
Operation
Description
FLASHER
RH
Outputs the voltage to blink the right side turn signal lamps
LH
Outputs the voltage to blink the left side turn signal lamps
Off
Stops the voltage to turn the turn signal lamps OFF
Monitor Item [Unit]
Contents
FAN ON SIG
[On/Off]
Displays blower motor status as judged from blower fan ON signal.
AIR COND SW
[On/Off]
Displays A/C switch status as judged from A/C switch signal.
THERMO AMP
[On/Off]
Displays thermo control amp. status as judged from thermo control amp. signal.
IGN SW
[On/Off]
Displays ignition switch position status as judged form ignition switch signal.
FR DEF SW
[On/Off]
Displays the D/F or DEF status as judged from defroster position signal.
Test item
Operation
Description
A/C INDICATOR
On
A/C indicator is turned ON.
Off
A/C indicator is turned OFF.
Revision: 2011 October
2012 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-103
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BCM
BCM : CONSULT Function (BCM - BCM)
INFOID:0000000007576712
WORK SUPPORT
IMMU
IMMU : CONSULT Function (BCM - IMMU)
INFOID:0000000007829443
WORK SUPPORT
Monitor item [UNIT]
Description
TURN SIGNAL R
[Off/On]
Displays the status of TURN RH switch in combination switch judged by the combination switch reading func-
tion.
TURN SIGNAL L
[Off/On]
Displays the status of the TURN LH switch in combination switch judged by the combination switch reading
function.
HI BEAM SW
[Off/On]
Displays the status of HI BEAM switch in combination switch judged by the combination switch reading func-
tion.
HEAD LAMP SW 1
[Off/On]
Displays the status of HEADLAMP 1 switch in combination switch judged by the combination switch reading
function.
HEAD LAMP SW 2
[Off/On]
Displays the status of HEADLAMP 2 switch in combination switch judged by the combination switch reading
function.
TAIL LAMP SW
[Off/On]
Displays the status of TAIL LAMP switch in combination switch judged by the combination switch reading
function.
PASSING SW
[Off/On]
Displays the status of PASSING switch in combination switch judged by the combination switch reading func-
tion.
AUTO LIGHT SW
[Off/On]
NOTE:
This item is indicated, but not monitored.
FR FOG SW
[Off/On]
Displays the status of FR FOG switch in combination switch judged by the combination switch reading func-
tion.
RR FOG SW
[Off/On]
NOTE:
This item is indicated, but not monitored.
FR WIPER HI
[Off/On]
Displays the status of FR WIPER HI switch in combination switch judged by the combination switch reading
function.
FR WIPER LOW
[Off/On]
Displays the status of FR WIPER LOW switch in combination switch judged by the combination switch read-
ing function.
FR WIPER INT
[Off/On]
Displays the status of FR WIPER INT switch in combination switch judged by the combination switch reading
function.
FR WASHER SW
[Off/On]
Displays the status of FR WASHER switch in combination switch judged by the combination switch reading
function.
INT VOLUME
[1 - 7]
Displays the status of wiper intermittent dial position judged by the combination switch reading function.
RR WIPER ON
[Off/On]
Displays the status of RR WIPER switch in combination switch judged by the combination switch reading
function.
RR WIPER INT
[Off/On]
Displays the status of RR WIPER INT switch in combination switch judged by the combination switch reading
function.
RR WASHER SW
[Off/On]
Displays the status of RR WASHER switch in combination switch judged by the combination switch reading
function.
Item
Description
RESET SETTING VALUE
Return a value set with WORK SUPPORT of each system to a default value in factory shipment.
Revision: 2011 October
2012 JUKE
BCS-104
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
BATTERY SAVER
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)
INFOID:0000000007829433
WORK SUPPORT
*:Factory setting
DATA MONITOR
Service item
Description
CONFIRM DONGLE ID
It is possible to check that dongle unit is applied to the vehicle.
Test item
Description
THEFT IND
This test is able to check security indicator lamp operation. Security indicator lamp will be
turned on when “ON” on CONSULT screen is touched.
Service item
Setting item
Setting
ROOM LAMP TIMER SET
MODE 1
30 min.
Sets the interior room lamp battery saver timer operating
time.
MODE 2
60 min.
MODE 3
*
15 min.
ROOM LAMP BAT SAV SET
On
*
With the interior room lamp battery saver function
Off
Without the interior room lamp battery saver function
Monitor item
[Unit]
Description
IGN ON SW
[On/Off]
Ignition switch (ON) status judeges from IGN signal (ignition power supply)
KEY ON SW
[On/Off]
The switch status input from key switch
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]
The switch status input from rear door switch LH
BACK DOOR SW
[On/Off]
The switch status input from back door switch
LOCK STATUS
[On/Off]
The switch status input from door lock status switch (driver side)
CDL LOCK SW
[On/Off]
Lock switch status input from door lock and unlock switch
CDL UNLOCK SW
[On/Off]
Unlock switch status input from door lock and unlock switch
KEYLESS LOCK
[On/Off]
Lock signal status received from remote keyless entry receiver
KEYLESS UNLOCK
[On/Off]
Unlock signal status received from remote keyless entry receiver
TRNK/HAT MNTR
[On/Off]
NOTE:
The item is indicated, but not monitored
Revision: 2011 October
2012 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-105
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
*: Each lamp switch is in ON position.
TRUNK
TRUNK : CONSULT Function (BCM - TRUNK)
INFOID:0000000007829423
DATA MONITOR
THEFT ALM
THEFT ALM : CONSULT Function (BCM - THEFT)
INFOID:0000000007829444
WORK SUPPORT
ACTIVE TEST
KEY CYL LK-SW
[On/Off]
Lock switch status received from key cylinder switch
KEY CYL UN-SW
[On/Off]
Unlock switch status received from key cylinder switch
ACC ON SW
[On/Off]
Ignition switch (ACC) status judges from ACC signal (ACC power supply)
Monitor item
[Unit]
Description
Test item
Operation
Description
BATTERY SAVER
Off
Cuts the interior room lamp power supply to turn interior room lamps OFF.
On
Outputs the interior room lamp power supply to turn interior room lamps ON.*
Monitor Item
Contents
KEY ON SW
Indicates [On/Off] condition of key switch.
LOCK STATUS
NOTE:
This item is displayed, but cannot be monitored.
VEHICLE SPEED
Indicates [Km/h] condition of vehicle speed signal from combination meter.
IGN ON SW
Indicates [On/Off] condition of ignition switch.
TRNK OPNR SW
NOTE:
This item is displayed, but cannot be monitored.
KYLS TRNK/HAT
NOTE:
This item is displayed, but cannot be monitored.
Service Item
Description
SECURITY ALARM SET
This mode is able to confirm and change security alarm ON-OFF setting.
THEFT ALM TRG
The switch which triggered vehicle security alarm is recorded.
This mode is able to confirm and erase the record of vehicle security alarm.
The trigger data can be erased by touching “CLEAR” on CONSULT screen.
Test Item
Description
THEFT IND
This test is able to check security indicator lamp operation. Security indicator lamp will be
turned on when “ON” on CONSULT screen is touched.
VEHICLE SECURITY HORN
This test is able to check horn operation. Horn will be activated for 0.5 seconds after “ON” on
CONSULT screen is touched.
HEADLAMP (HI)
This test is able to check headlamp (HI) operation. Headlamps (HI) will be activated for 0.5
seconds after “ON” on CONSULT screen is touched.
FLASHER
This test is able to check hazard warning lamp operation. Hazard warning lamps will be acti-
vated after “LH” or “RH” on CONSULT screen is touched.
Revision: 2011 October
2012 JUKE
BCS-106
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
RETAIND PWR
RETAIND PWR : CONSULT Function (BCM - RETAINED PWR)
INFOID:0000000007829425
DATA MONITOR
SIGNAL BUFFER
SIGNAL BUFFER : CONSULT Function (BCM - SIGNAL BUFFER)
INFOID:0000000007576718
DATA MONITOR
ACTIVE TEST
PANIC ALARM
PANIC ALARM : CONSULT Function (BCM - PANIC ALARM)
INFOID:0000000007829442
ACTIVE TEST
AIR PRESSURE MONITOR
AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE MONI-
TOR)
INFOID:0000000007829441
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SELF DIAGNOSTIC RESULT
Monitor Item
Description
DOOR SW-DR
Indicates [ON/OFF] condition of driver side door switch.
DOOR SW-AS
Indicates [ON/OFF] condition of passenger side door switch.
Monitor item [UNIT]
Description
OIL PRESS SW
[Off/On]
NOTE:
This item is indicated, but not monitored.
BRAKE SW
[Off/On]
Displays the switch status input from stop lamp switch.
Test item
Operation
Description
OIL PRESSURE SW
Off
NOTE:
This item is indicated, but not tested.
On
Test item
Description
VEHICLE SECURITY HORN
This test is able to check horn operation.
Horn is activated for 0.5 seconds after “ON” on CONSULT screen touched.
HEAD LAMP (HI)
This test is able to check headlamp (HI) operation.
Headlamps (HI) will be activated after “ON” on CONSULT screen touched.
Diagnosis mode
Function Description
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Work Support
Components can be quickly and accurately adjusted.
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст