Nissan Juke (2012 year). Service Repair Manual — part 175
PCS-84
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
B2616 IGNITION RELAY CIRCUIT
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK IGNITION RELAY GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between ignition relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair ignition relay ground circuit.
4.
CHECK IGNITION RELAY POWER SUPPLY CIRCUIT-2
1.
Turn ignition switch ON.
2.
Check voltage between ignition relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Check continuity open or short between ignition relay and battery.
5.
CHECK IGNITION RELAY
PCS-84, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace ignition relay.
6.
CHECK INTERMITTENT INCIDENT
GI-43, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000007579403
1.
CHECK IGNITION RELAY
1.
Turn ignition switch OFF.
2.
Remove ignition relay.
3.
Check the continuity between ignition relay terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace Ignition relay
Ignition relay
Ground
Continuity
Terminal
1
Existed
(+)
(–)
Voltage (V)
(Approx.)
Ignition relay
Terminal
5
Ground
Battery voltage
Terminals
Condition
Continuity
3 and 5
12 V direct current supply between terminals 1 and 2
Existed
No current supply
Not existed
PBIB0098E
Revision: 2011 October
2012 JUKE
PCS
B2618 BCM
PCS-85
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
B2618 BCM
DTC Logic
INFOID:0000000007579404
DTC DETECTION LOGIC
NOTE:
• If DTC B2618 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2618 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions, and wait for 1 second or more.
CVT models
-
Selector lever is in the P or N position
-
Do not depress brake pedal
M/T models
-
Do not depress clutch pedal
2.
Check “Self-diagnosis result” of BCM with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007579405
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Select “Self-diagnosis result” of BCM with CONSULT.
3.
Touch “ERASE”.
4.
Perform DTC Confirmation Procedure.
See
.
Is the 1st trip DTC B2618 displayed again?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> INSPECTION END
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2618
BCM
An immediate operation of ignition relay (IPDM E/R) is re-
quested by BCM, but there is no response for more than
1 second
BCM
Revision: 2011 October
2012 JUKE
PCS-86
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
B261A PUSH-BUTTON IGNITION SWITCH
B261A PUSH-BUTTON IGNITION SWITCH
DTC Logic
INFOID:0000000007579406
DTC DETECTION LOGIC
NOTE:
• If DTC B261A is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B261A is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Press the push-button ignition switch under the following conditions, and wait for 1 second or more.
CVT models
-
Selector lever is in the P or N position
-
Do not depress brake pedal
M/T models
-
Do not depress clutch pedal
2.
Check “Self-diagnosis result” of BCM with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007579407
1.
CHECK IGNITION SWITCH OUTPUT SIGNAL (PUSH-BUTTON IGNITION SWITCH)
1.
Disconnect push-button ignition switch connector and IPDM E/R connector.
2.
Check voltage between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT (BCM)
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and push-button ignition switch harness connector.
3.
Check continuity between push-button ignition switch harness connector and ground.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B261A
PUSH-BTN IGN SW
BCM detects a difference of signal for 1 second or
more between the following items.
• Push-button ignition switch signal
• Push-button ignition switch status signal (CAN)
• Harness or connectors
(Push-button ignition switch circuit
is open or shorted.)
• BCM
• IPDM E/R
(+)
(–)
Voltage (V)
(Approx.)
Push-button ignition switch
Connector
Terminal
M101
8
Ground
12
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M70
76
M101
8
Existed
Revision: 2011 October
2012 JUKE
PCS
B261A PUSH-BUTTON IGNITION SWITCH
PCS-87
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK IGNITION SWITCH OUTPUT SIGNAL (IPDM E/R)
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> GO TO 4.
4.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT (IPDM E/R)
1.
Disconnect BCM connector.
2.
Check continuity between IPDM E/R harness connector and push-button ignition switch harness connec-
tor.
3.
Check continuity between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK INTERMITTENT INCIDENT
GI-43, "Intermittent Incident"
.
>> INSPECTION END
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M101
8
Not existed
(+)
(–)
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E17
66
Ground
12
IPDM E/R
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
E17
66
M101
8
Existed
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M101
8
Not existed
Revision: 2011 October
2012 JUKE
PCS-88
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
B26F1 IGNITION RELAY
B26F1 IGNITION RELAY
DTC Logic
INFOID:0000000007579408
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions, and wait for 2 seconds or more.
CVT models
-
Selector lever is in the P or N position
-
Do not depress brake pedal
M/T models
-
Do not depress clutch pedal
2.
Check “Self-diagnosis result” with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007579409
1.
CHECK IPDM E/R SELF-DIAGNOSTIC RESULT
1.
Turn ignition switch ON.
2.
Erase the DTC of IPDM E/R.
3.
Turn ignition switch OFF.
4.
Turn ignition switch ON and check the DTC again.
Is DTC detected?
YES
>> Repair or replace the malfunctioning part. Refer to
NO
>> GO TO 2.
2.
CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
3.
CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM and IPDM connectors.
3.
Check continuity between BCM harness connector and IPDM E/R harness connector.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B26F1
IGN RELAY OFF
BCM transmits the ignition relay control signal
(ON: 0 V) or ignition switch ON signal (ON)
(CAN), but does not receives ignition switch
ON signal (ON) (CAN) from IPDM E/R.
• Harness or connectors
(Ignition relay circuit is open)
• BCM
• IPDM E/R
(+)
(–)
Condition
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M70
98
Ground
Ignition switch
ON
0
Revision: 2011 October
2012 JUKE
PCS
B26F1 IGNITION RELAY
PCS-89
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace harness.
BCM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
M70
98
E17
68
Existed
Revision: 2011 October
2012 JUKE
PCS-90
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
B26F2 IGNITION RELAY
B26F2 IGNITION RELAY
DTC Logic
INFOID:0000000007579410
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions, and wait for 2 seconds or more.
CVT models
-
Selector lever is in the P or N position
-
Do not depress brake pedal
M/T models
-
Do not depress clutch pedal
2.
Check “Self-diagnosis result” with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007579411
1.
CHECK IPDM E/R SELF-DIAGNOSTIC RESULT
1.
Turn ignition switch ON.
2.
Erase the DTC of IPDM E/R.
3.
Turn ignition switch OFF.
4.
Turn ignition switch ON and check the DTC again.
Is DTC detected?
YES
>> Repair or replace the malfunctioning part. Refer to
NO
>> GO TO 2.
2.
CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL
1.
Turn ignition switch OFF.
2.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> GO TO 3.
3.
CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL CIRCUIT - 1
1.
Turn ignition switch OFF.
2.
Disconnect BCM and IPDM E/R connectors.
3.
Check continuity between IPDM E/R harness connector and ground.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B26F2
IGN RELAY ON
BCM transmits the ignition relay control signal
(OFF: 12 V) or ignition switch ON signal (OFF)
(CAN), but does not receives ignition switch
ON signal (OFF) (CAN) from IPDM E/R.
• Harness or connectors
(Ignition relay circuit is short)
• BCM
• IPDM E/R
(+)
(–)
Condition
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E17
68
Ground
Ignition switch
OFF or ACC
12
Revision: 2011 October
2012 JUKE
PCS
B26F2 IGNITION RELAY
PCS-91
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL CIRCUIT - 2
1.
Connect IPDM E/R connectors.
2.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> Replace IPDM E/R.
IPDM E/R
Ground
Continuity
Connector
Terminal
E17
68
Not existed
(+)
(–)
Condition
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E17
68
Ground
Ignition switch
OFF or ACC
12
Revision: 2011 October
2012 JUKE
PCS-92
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
B26F6 BCM
B26F6 BCM
DTC Logic
INFOID:0000000007579412
DTC DETECTION LOGIC
NOTE:
• If DTC B26F6 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B26F6 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions, and wait for 1 second or more.
CVT models
-
Selector lever is in the P or N position
-
Do not depress brake pedal
M/T models
-
Do not depress clutch pedal
2.
Check “Self-diagnosis result” of BCM with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007579413
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Select “Self-diagnosis result” of BCM with CONSULT.
3.
Touch “ERASE”.
4.
Perform DTC Confirmation Procedure.
See
Is DTC detected?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> INSPECTION END
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B26F6
BCM
Ignition relay ON signal is not transmitted from IPDM E/
R when BCM turns ignition relay ON.
BCM
Revision: 2011 October
2012 JUKE
PCS
PUSH-BUTTON IGNITION SWITCH
PCS-93
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
PUSH-BUTTON IGNITION SWITCH
Component Function Check
INFOID:0000000007579414
1.
CHECK FUNCTION
1.
Select “PUSH SW” in “Data Monitor” mode with CONSULT.
2.
Check the push-button ignition switch signal under the following conditions.
Is the indication normal?
YES
>> INSPECTION END.
NO
Diagnosis Procedure
INFOID:0000000007579415
1.
CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL 1
1.
Turn ignition switch OFF.
2.
Disconnect push-button ignition switch connector and IPDM E/R connector.
3.
Check voltage between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT 1
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and push-button ignition switch harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL 2
Check voltage between IPDM E/R harness connector and ground.
Test item
Condition
Status
PUSH SW
Push-button ignition switch is pressed
ON
Push-button ignition switch is not pressed
OFF
(+)
(–)
Voltage (V)
(Approx.)
Push-button ignition switch
Connector
Terminal
M101
8
Ground
12
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M70
76
M101
8
Existed
BCM
Ground
Continuity
Connector
Terminal
M70
76
Not existed
Revision: 2011 October
2012 JUKE
PCS-94
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
PUSH-BUTTON IGNITION SWITCH
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT 2
1.
Disconnect BCM connector.
2.
Check continuity between IPDM E/R harness connector and push-button ignition switch harness connec-
tor.
3.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace harness.
5.
CHECK PUSH-BUTTON IGNITION SWITCH GROUND CIRCUIT
Check continuity between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK PUSH-BUTTON IGNITION SWITCH
PCS-94, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace push-button ignition switch.
7.
CHECK INTERMITTENT INCIDENT
GI-43, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000007579416
1.
CHECK PUSH-BUTTON IGNITION SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect push-button ignition switch connector.
3.
Check continuity between push-button ignition switch terminals.
(+)
(–)
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E17
66
Ground
12
IPDM E/R
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
E17
66
M101
8
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E17
66
Not existed
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M101
4
Existed
Revision: 2011 October
2012 JUKE
PCS
PUSH-BUTTON IGNITION SWITCH
PCS-95
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace push-button ignition switch.
Push-button ignition switch
Condition
Continuity
Terminal
4
8
Pressed
Existed
Not pressed
Not existed
Revision: 2011 October
2012 JUKE
PCS-96
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR
Description
INFOID:0000000007579417
Push-button ignition switch changes the power supply position.
BCM maintains the power supply position status.
BCM changes the power supply position with the operation of the push-button ignition switch.
Component Function Check
INFOID:0000000007579418
1.
CHECK FUNCTION
Check push-button ignition switch (“PUSH SWITCH INDICATOR”) in Active Test Mode with CONSULT.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007579419
1.
CHECK PUSH-BUTTON IGNITION SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect push-button ignition switch connector.
3.
Check voltage between push-button ignition switch harness connector and ground.
Is the inspection normal?
YES
>> GO TO 2.
NO-1
>> Check 10 A fuse [No.13, located in fuse block (J/B)].
NO-2
>> Check harness for open or short between push-button ignition switch and fuse.
2.
CHECK BCM INPUT
1.
Connect push-button ignition switch connector.
2.
Disconnect BCM connector.
3.
Check voltage between BCM connector and ground.
Is the inspection normal?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> GO TO 3.
3.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT
1.
Disconnect push-button ignition switch connector.
2.
Check continuity between BCM harness connector and push-button ignition switch harness connector.
Test item
Description
PUSH SWITCH INDICATOR
ON
Position indicator
Illuminates
OFF
Does not illuminate
(+)
(–)
Voltage (V)
(Approx.)
Push-button ignition switch
Connector
Terminal
M101
3
Ground
Battery voltage
(+)
(–)
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M70
91
Ground
Battery voltage
Revision: 2011 October
2012 JUKE
PCS
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR
PCS-97
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
3.
Check continuity between BCM harness connector and ground.
Is the inspection normal?
YES
>> Replace push-button ignition switch.
NO
>> Repair or replace harness.
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M70
91
M101
7
Existed
BCM
Ground
Continuity
Connector
Terminal
M70
91
Not existed
Revision: 2011 October
2012 JUKE
PCS-98
< SYMPTOM DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
PUSH-BUTTON IGNITION SWITCH DOES NOT OPERATE
SYMPTOM DIAGNOSIS
PUSH-BUTTON IGNITION SWITCH DOES NOT OPERATE
Description
INFOID:0000000007579420
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check
each symptom.
NOTE:
The engine start function, door lock function, power distribution system, and NATS-IVIS/NVIS in the Intelligent
Key system are closely related to each other regarding control. The vehicle security function can operate only
when the door lock and power distribution system are operating normally.
Conditions of Vehicle (Operating Conditions)
• “ENGINE START BY I-KEY” in “WORK SUPPORT” is ON when setting on CONSULT.
• One or more of Intelligent Keys with registered Intelligent Key ID is in the vehicle.
Diagnosis Procedure
INFOID:0000000007579421
1.
PERFORM WORK SUPPORT
Perform “INSIDE ANT DIAGNOSIS” on Work Support of “INTELLIGENT KEY”.
Refer to
DLK-28, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS RESULT
Perform Self-Diagnosis Result of “BCM”.
Is DTC detected?
YES
>> Refer to
NO
>> GO TO 3.
3.
CHECK PUSH-BUTTON IGNITION SWITCH
Check push-button ignition switch.
Refer to
PCS-93, "Component Function Check"
Is the operation normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2011 October
2012 JUKE
PCS
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR DOES NOT ILLUMI-
NATE
PCS-99
< SYMPTOM DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR DOES NOT IL-
LUMINATE
Description
INFOID:0000000007579422
• Before performing the diagnosis in the following table, check “Work Flow”. Refer to
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
Conditions of Vehicle (Operating Conditions)
• “ENGINE START BY I-KEY” in “WORK SUPPORT” is ON when setting on CONSULT.
• One or more of Intelligent Keys with registered Intelligent Key ID is in the vehicle.
Diagnosis Procedure
INFOID:0000000007579423
1.
CHECK PUSH-BUTTON IGNITION SWITCH INDICATOR
Check push-button ignition switch indicator.
Refer to
PCS-96, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст