Nissan Juke (2012 year). Service Repair Manual — part 120
HEADLAMP GROUND CIRCUIT
EXL-49
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
3.
Check continuity between headlamp LH harness connector and ground.
Is the inspection result normal?
YES
>> Headlamp LH ground circuit is normal.
NO
>> Repair or replace harness.
Headlamp LH
Ground
Continuity
Connector
Terminal
E26
2
Existed
Revision: 2011 October
2012 JUKE
EXL-50
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
DAYTIME RUNNING LIGHT RELAY CIRCUIT
DAYTIME RUNNING LIGHT RELAY CIRCUIT
Component Function Check
INFOID:0000000007579191
1.
CHECK DAYTIME RUNNING LIGHT OPERATION
CONSULT ACTIVE TEST
1.
Select “DAYTIME RUNNING LIGHT” of BCM (HEADLAMP) active test item.
2.
With operating the test items, check that daytime running light operation.
Is the inspection result normal?
YES
>> Daytime running light relay circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007579192
1.
CHECK DAYTIME RUNNING LIGHT RELAY 2 FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuse is not fusing.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the fuse after repairing the applicable circuit.
2.
CHECK DAYTIME RUNNING LIGHT RELAY 2 POWER SUPPLY
1.
Remove daytime running light relay.
2.
Check voltage between daytime running light relay 2 harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK DAYTIME RUNNING LIGHT RELAY 2
Check daytime running light relay 2. Refer to
EXL-51, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace daytime running light relay 2.
4.
CHECK DAYTIME RUNNING LIGHT RELAY 2 CONTROL SIGNAL OUTPUT
CONSULT ACTIVE TEST
1.
Install daytime running light relay 2.
2.
Turn ignition switch ON.
3.
Select “DAYTIME RUNNING LIGHT” of BCM (HEADLAMP) active test item.
4.
With operating the test item, check voltage between IPDM E/R harness connector and ground.
On
: Daytime running light ON
Off
: Daytime running light OFF
Unit
Fuse No.
Capacity
Daytime running light relay 2
#24
10 A
(+)
(
−
)
Voltage
(Approx.)
Daytime running light relay 2
Connector
Terminal
E65
1
Ground
Battery voltage
5
Revision: 2011 October
2012 JUKE
DAYTIME RUNNING LIGHT RELAY CIRCUIT
EXL-51
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Is the inspection result normal?
YES
>> Daytime running light relay 2 circuit is OK.
NO-1 (Fixed at 0 V)>>GO TO 5.
NO-2 (Fixed at battery voltage) >>Replace IPDM E/R.
5.
CHECK DAYTIME RUNNING LIGHT RELAY 2 CONTROL SIGNAL OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Remove daytime running light relay 2.
3.
Disconnect IPDM E/R harness connector.
4.
Check continuity between IPDM E/R harness connector and daytime running light relay 2 harness con-
nector.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK DAYTIME RUNNING LIGHT RELAY 2 CONTROL SIGNAL SHORT CIRCUIT
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace harness.
Component Inspection
INFOID:0000000007579193
1.
CHECK DAYTIME RUNNING LIGHT RELAY 2
1.
Turn the ignition switch OFF.
2.
Remove daytime running light relay 2.
3.
Apply battery voltage to daytime running light relay- between terminals 1 and 2.
4.
Check continuity between daytime running light relay 2 terminals.
Is the inspection result normal?
YES
>> Daytime running light relay 2 is normal.
NO
>> Replace daytime running light relay 2.
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
E13
28
Ground
DAYTIME RUN-
NING LIGHT
On
0 V
Off
Battery voltage
IPDM E/R
Daytime running light relay 2
Continuity
Connector
Terminal
Connector
Terminal
E13
28
E65
2
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E13
28
Not existed
Daytime running light relay-2
Condition
Continuity
Terminal
5
3
Voltage
Apply
Existed
Not Apply
Not existed
4
Apply
Not existed
Not Apply
Existed
Revision: 2011 October
2012 JUKE
EXL-52
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
PARKING LAMP CIRCUIT
PARKING LAMP CIRCUIT
Component Function Check
INFOID:0000000007579194
1.
CHECK PARKING LAMP OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the parking lamp is turned ON.
Is the inspection result normal?
YES
>> Parking lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007579195
1.
CHECK PARKING LAMP FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuses are not fusing.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK PARKING LAMP SHORT CIRCUIT
1.
Disconnect the following connectors.
-
IPDM E/R
-
Parking lamp
-
Front side marker lamp
-
Rear combination lamp
-
Back door opener switch
2.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace fuse. (Replace IPDM E/R if fusing is found again.)
NO
>> Repair or replace harness. And then replace the fuse.
3.
CHECK PARKING LAMP BULB
Check applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace bulb.
4.
CHECK PARKING LAMP OUTPUT VOLTAGE
CONSULT ACTIVE TEST
TAIL
: Parking lamp ON
Off
: Parking lamp OFF
Unit
Location
Fuse No.
Capacity
• Parking lamp
• Front side marker lamp
• Tail lamp
• License plate lamp
IPDM E/R
#47
10 A
IPDM E/R
Ground
Continuity
Connector
Terminal
E14
43
Not existed
44
Revision: 2011 October
2012 JUKE
PARKING LAMP CIRCUIT
EXL-53
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
1.
Disconnect parking lamp connector.
2.
Turn ignition switch ON.
3.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4.
With operating the test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace IPDM E/R.
5.
CHECK PARKING LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and parking lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK PARKING LAMP GROUND OPEN CIRCUIT
Check continuity between parking lamp harness connector and ground.
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
E14
43
Ground
EXTERNAL
LAMPS
TAIL
Battery voltage
Off
0 V
IPDM E/R
Parking lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E14
43
E43
1
Existed
LH
E24
Parking lamp
Ground
Continuity
Connector
Terminal
RH
E43
2
Existed
LH
E24
Revision: 2011 October
2012 JUKE
EXL-54
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
FRONT SIDE MARKER LAMP CIRCUIT
FRONT SIDE MARKER LAMP CIRCUIT
Component Function Check
INFOID:0000000007579196
1.
CHECK PARKING LAMP OPERATION
Check that the parking lamp is turned ON.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check parking lamp circuit. Refer to
EXL-52, "Component Function Check"
2.
CHECK FRONT SIDE MARKER LAMP OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the front side marker lamp is turned ON.
Is the inspection result normal?
YES
>> Front side marker lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007579197
1.
CHECK FRONT SIDE MARKER LAMP BULB
Check applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace bulb.
2.
CHECK FRONT SIDE MARKER LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector and front side marker lamp connector.
3.
Check continuity between IPDM E/R harness connector and front side marker lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK FRONT SIDE MARKER LAMP GROUND OPEN CIRCUIT
Check continuity between front side marker lamp harness connector and ground.
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
TAIL
: Front side marker lamp ON
Off
: Front side marker lamp OFF
IPDM E/R
Front side marker lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E14
43
E32
1
Existed
LH
E31
Front side marker lamp
Ground
Continuity
Connector
Terminal
RH
E32
2
Existed
LH
E31
Revision: 2011 October
2012 JUKE
TAIL LAMP CIRCUIT
EXL-55
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
TAIL LAMP CIRCUIT
Component Function Check
INFOID:0000000007579198
1.
CHECK PARKING LAMP AND FRONT SIDE MARKER LAMP OPERATION
Check that the parking lamp and front side marker lamp are turned ON.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check parking lamp circuit. Refer to
EXL-52, "Component Function Check"
2.
CHECK TAIL LAMP OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the tail lamp is turned ON.
Is the inspection result normal?
YES
>> Tail lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007579199
1.
CHECK TAIL LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace bulb.
2.
CHECK TAIL LAMP OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1.
Disconnect rear combination lamp connector.
2.
Turn ignition switch ON.
3.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4.
With operating the test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace IPDM E/R.
3.
CHECK TAIL LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector and rear combination lamp connector.
3.
Check continuity between IPDM E/R harness connector and rear combination lamp harness connector.
TAIL
: Tail Lamp ON
Off
: Tail lamp OFF
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
E14
44
Ground
EXTERNAL
LAMPS
TAIL
Battery voltage
Off
0 V
IPDM E/R
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E14
44
B59
2
Existed
LH
B80
Revision: 2011 October
2012 JUKE
EXL-56
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
TAIL LAMP CIRCUIT
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK TAIL LAMP GROUND OPEN CIRCUIT
Check continuity between rear combination lamp harness connector and ground.
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
Rear combination lamp
Ground
Continuity
Connector
Terminal
RH
B59
3
Existed
LH
B80
Revision: 2011 October
2012 JUKE
LICENSE PLATE LAMP CIRCUIT
EXL-57
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LICENSE PLATE LAMP CIRCUIT
Component Function Check
INFOID:0000000007579200
1.
CHECK TAIL LAMP OPERATION
Check that the tail lamp is turned ON.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check tail lamp circuit. Refer to
EXL-55, "Component Function Check"
.
2.
CHECK LICENSE PLATE LAMP OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the lighting switch, check that the license plate lamp is turned ON.
Is the inspection result normal?
YES
>> License plate lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007579201
1.
CHECK LICENSE PLATE LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace bulb.
2.
CHECK LICENSE PLATE LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector and back door opener switch connector.
3.
Check continuity between IPDM E/R harness connector and back door opener switch harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK LICENSE PLATE LAMP GROUND OPEN CIRCUIT
Check continuity between back door opener switch harness connector and ground.
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
TAIL
: License plate lamp ON
Off
: License plate lamp OFF
IPDM E/R
Back door opener switch
Continuity
Connector
Terminal
Connector
Terminal
E14
44
D107
5
Existed
Back door opener switch
Ground
Continuity
Connector
Terminal
D107
6
Existed
Revision: 2011 October
2012 JUKE
EXL-58
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
OPTICAL SENSOR
OPTICAL SENSOR
Component Function Check
INFOID:0000000007579202
1.
CHECK OPTICAL SENSOR SIGNAL BY CONSULT
CONSULT DATA MONITOR
1.
Turn ignition switch ON.
2.
Select “OPTISEN (DTCT)” of BCM (HEADLAMP) data monitor item.
3.
Turn lighting switch AUTO.
4.
With the optical sensor illuminating, check the monitor status.
*: Illuminates the optical sensor. The value may be less than the standard value if brightness is weak.
Is the inspection result normal?
YES
>> Optical sensor is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007579203
1.
CHECK OPTICAL SENSOR POWER SUPPLY INPUT
1.
Turn ignition switch ON.
2.
Turn lighting switch AUTO.
3.
Check voltage between optical sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK OPTICAL SENSOR GROUND INPUT
Check voltage between optical sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 6.
3.
CHECK OPTICAL SENSOR SIGNAL OUTPUT
With illuminating the optical sensor, check voltage between optical sensor harness connector and ground.
Monitor item
Condition
Voltage (Approx.)
OPTISEN (DTCT)
Optical sensor
When illuminating
3.1 V or more *
When shutting off light
0.6 V or less
(+)
(
−
)
Voltage
(Approx.)
Optical sensor
Connector
Terminal
M84
1
Ground
5 V
(+)
(
−
)
Voltage
(Approx.)
Optical sensor
Connector
Terminal
M84
3
Ground
0 V
Revision: 2011 October
2012 JUKE
OPTICAL SENSOR
EXL-59
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
*: Illuminate the optical sensor. The value may be less than the standard if brightness is weak.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace the optical sensor.
4.
CHECK OPTICAL SENSOR OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect optical sensor connector and BCM connector.
3.
Check continuity between optical sensor harness connector and BCM harness connector.
*
1
: Without Intelligent Key
*
2
: With Intelligent Key
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK OPTICAL SENSOR SHORT CIRCUIT
Check continuity between optical sensor harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
(with Intelligent Key) or
(without Intelligent Key).
NO
>> Repair or replace harness.
6.
CHECK OPTICAL SENSOR GROUND OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect optical sensor connector and BCM connector.
3.
Check continuity between optical sensor harness connector and BCM harness connector.
*
1
: Without Intelligent Key
*
2
: With Intelligent Key
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
(with Intelligent Key) or
(without Intelligent Key).
(+)
(
−
)
Condition
Voltage
(Approx.)
Optical sensor
Connector
Terminal
M84
2
Ground
Optical sensor
When illuminating
3.1 V or more *
When shutting off light
0.6 V or less
Optical sensor
BCM
Continuity
Connector
Terminal
Connector
Terminal
M84
1
M65*
1
M68*
2
17
Existed
Optical sensor
Ground
Continuity
Connector
Terminal
M84
1
Not existed
Optical sensor
BCM
Continuity
Connector
Terminal
Connector
Terminal
M84
3
M65*
1
M68*
2
18
Existed
Revision: 2011 October
2012 JUKE
EXL-60
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
OPTICAL SENSOR
NO
>> Repair or replace harness.
7.
CHECK OPTICAL SENSOR SIGNAL OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect optical sensor connector and BCM connector.
3.
Check continuity between optical sensor harness connector and BCM harness connector.
*
1
: Without Intelligent Key
*
2
: With Intelligent Key
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace harness.
8.
CHECK OPTICAL SENSOR SHORT CIRCUIT
Check continuity between optical sensor harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
(without Intelligent Key).
NO
>> Repair or replace harness.
Optical sensor
BCM
Continuity
Connector
Terminal
Connector
Terminal
M84
2
M65*
1
M68*
2
14
Existed
Optical sensor
Ground
Continuity
Connector
Terminal
M84
2
Not existed
Revision: 2011 October
2012 JUKE
FRONT FOG LAMP CIRCUIT
EXL-61
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP CIRCUIT
Component Function Check
INFOID:0000000007579204
1.
CHECK FRONT FOG LAMP OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the front fog lamp is turned ON.
Is the measurement normal?
YES
>> Front fog lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007579205
1.
CHECK FRONT FOG LAMP FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuse is not fusing.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK FRONT FOG LAMP SHORT CIRCUIT
1.
Disconnect front fog connector and IPDM E/R connector.
2.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO
>> Repair or replace harness. And then replace the fuse.
3.
CHECK FRONT FOG LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace bulb.
4.
CHECK FRONT FOG LAMP OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1.
Disconnect front fog lamp connector.
2.
Turn ignition switch ON.
3.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4.
With operating the test items, check the voltage between IPDM E/R harness connector and ground.
Fog
: Front fog lamp ON
Off
: Front fog lamp OFF
Unit
Location
Fuse No.
Capacity
Front fog lamp
IPDM E/R
#50
15 A
IPDM E/R
Ground
Continuity
Connector
Terminal
RH
E12
19
Not existed
LH
20
Revision: 2011 October
2012 JUKE
EXL-62
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
FRONT FOG LAMP CIRCUIT
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace IPDM E/R.
5.
CHECK FRONT FOG LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and front fog lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK FRONT FOG LAMP GROUND CIRCUIT OPEN CIRCUIT
Check continuity between front fog lamp harness connector and ground.
Is the inspection result normal?
YES
>> Refer to
GI-43, "Intermittent Incident"
.
NO
>> Repair or replace harness.
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
RH
E12
19
Ground
EXTERNAL
LAMPS
Fog
Battery voltage
Off
0 V
LH
20
Fog
Battery voltage
Off
0 V
IPDM E/R
Front fog lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E12
19
E48
1
Existed
LH
20
E30
Front fog lamp
Ground
Continuity
Connector
Terminal
RH
E48
2
Existed
LH
E30
Revision: 2011 October
2012 JUKE
TURN SIGNAL LAMP CIRCUIT
EXL-63
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
TURN SIGNAL LAMP CIRCUIT
Component Function Check
INFOID:0000000007579206
1.
CHECK TURN SIGNAL LAMP
CONSULT ACTIVE TEST
1.
Select “FLASHER” of BCM (FLASHER) active test item.
2.
With operating the test items, check that the turn signal lamps is turned ON.
Is the inspection result normal?
YES
>> Turn signal lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007579207
1.
CHECK TURN SIGNAL LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace bulb.
2.
CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE
1.
Turn ignition switch OFF.
2.
Disconnect front turn signal lamp connector, side turn signal lamp connector and rear combination lamp
connector.
3.
Turn ignition switch ON.
4.
With operating the turn signal switch, check voltage between BCM harness connector and ground.
*
1
: Without Intelligent Key
*
2
: With Intelligent Key
LH
: Turn signal lamps (LH) ON
RH
: Turn signal lamps (RH) ON
Off
: Turn signal lamps OFF
(+)
(–)
Condition
Voltage
(Approx.)
BCM
Connector
Terminal
B9*
1
M69*
2
49*
1
60*
2
Ground
Turn signal
switch
LH
OFF
0 V
48*
1
61*
2
RH
OFF
0 V
PKID0926E
PKID0926E
Revision: 2011 October
2012 JUKE
EXL-64
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
TURN SIGNAL LAMP CIRCUIT
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
CHECK TURN SIGNAL LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and front turn signal lamp, side turn signal lamp or rear
combination lamp harness connector.
Front turn signal lamp
Side turn signal lamp
Rear turn signal lamp
*
1
: Without Intelligent Key
*
2
: With Intelligent Key
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
4.
CHECK TURN SIGNAL LAMP SHORT CIRCUIT
Check continuity between BCM harness connector and ground.
*
1
: Without Intelligent Key
*
2
: With Intelligent Key
Is the inspection result normal?
BCM
Front turn signal lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
B9*
1
M69*
2
48*
1
61*
2
E46
1
Existed
LH
49*
1
60*
2
E27
BCM
Side turn signal lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
B9*
1
M69*
2
48*
1
61*
2
E40
1
Existed
LH
49*
1
60*
2
E23
BCM
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
B9*
1
M69*
2
48*
1
61*
2
B59
5
Existed
LH
49*
1
60*
2
B80
BCM
Ground
Continuity
Connector
Terminal
RH
B9
*1
M69
*2
48*
1
61*
2
Not existed
LH
49*
1
60*
2
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст