Nissan Juke (2012 year). Service Repair Manual — part 121
TURN SIGNAL LAMP CIRCUIT
EXL-65
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
YES
>> Check each bulb socket for internal short circuit, and if check result is normal, replace BCM. Refer
to
BCS-80, "Removal and Installation"
(with Intelligent Key),
BCS-141, "Removal and Installation"
(without Intelligent Key).
NO
>> Repair or replace harness.
5.
CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT
Check continuity between BCM harness connector and front turn signal lamp, side turn signal lamp or rear
combination lamp and ground.
Front turn signal lamp
Side turn signal lamp
Rear turn signal lamp
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
Front turn signal lamp
Ground
Continuity
Connector
Terminal
RH
E46
2
Existed
LH
E27
Side turn signal lamp
Ground
Continuity
Connector
Terminal
RH
E40
2
Existed
LH
E23
Rear combination lamp
Ground
Continuity
Connector
Terminal
RH
B59
3
Existed
LH
B80
Revision: 2011 October
2012 JUKE
EXL-66
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
HAZARD SWITCH
HAZARD SWITCH
Component Function Check
INFOID:0000000007579208
1.
CHECK HAZARD SWITCH SIGNAL BY CONSULT
CONSULT DATA MONITOR
1.
Turn the ignition switch ON.
2.
Select “HAZARD SW” of BCM (FLASHER) data monitor item.
3.
With operating the hazard switch, check the monitor status.
Is the inspection result normal?
YES
>> Hazard switch circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007579209
1.
CHECK HAZARD SWITCH SIGNAL INPUT
1.
Turn ignition switch OFF.
2.
Disconnect hazard switch connector.
3.
Check voltage between hazard switch connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK HAZARD SWITCH SIGNAL OPEN CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between hazard switch harness connector and BCM harness connector.
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK HAZARD SWITCH SIGNAL SHORT CIRCUIT
Check continuity between hazard switch harness connector and ground.
Is the inspection result normal?
Monitor item
Condition
Monitor status
HAZARD SW
Hazard switch
ON
On
OFF
Off
(+)
(
−
)
Voltage (Approx.)
Hazard switch
Connector
Terminal
M45
2
Ground
12 V
Hazard switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
M45
2
M65
*1
M68
*2
29
Existed
Hazard switch
Ground
Continuity
Connector
Terminal
M45
2
Not existed
Revision: 2011 October
2012 JUKE
HAZARD SWITCH
EXL-67
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
YES
BCS-80, "Removal and Installation"
(With Intelligent Key) or
(Without Intelligent Key).
NO
>> Repair or replace harness.
4.
CHECK HAZARD SWITCH GROUND OPEN CIRCUIT
Check continuity between hazard switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace hazard switch.
NO
>> Repair or replace harness.
Hazard switch
Ground
Continuity
Connector
Terminal
M45
1
Existed
Revision: 2011 October
2012 JUKE
EXL-68
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
EXTERIOR LIGHTING SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
EXTERIOR LIGHTING SYSTEM SYMPTOMS
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Symptom Table
INFOID:0000000007579210
NOTE:
Perform the self-diagnosis with CONSULT before symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.
Symptom
Possible cause
Inspection item
Headlamp (HI) is not
turned ON.
One side
• Fuse
• Halogen bulb
• Harness between IPDM E/R and
headlamp
• IPDM E/R
Headlamp (HI) circuit
Refer to
.
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to
High beam indicator lamp is not turned ON.
[Headlamp (HI) is turned ON.]
Combination meter
• Combination meter
Data monitor “HI-BEAM IND”
• BCM (HEADLAMP)
Active test “HEADLAMP”
Headlamp (LO) is not
turned ON.
One side
• Fuse
• Halogen bulb
• Harness between IPDM E/R and
headlamp
• IPDM E/R
Headlamp (LO) circuit
Refer to
TIME RUNNING LIGHT SYSTEM :
Component Function Check"
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to
Headlamp is not turned
OFF.
When ignition switch
is turned ON.
When ignition switch
is turned OFF.
IPDM E/R
—
Headlamp HI and LO are not turned ON.
• Halogen bulb
• Harness between headlamp and
ground
Headlamp ground circuit
Refer to
TIME RUNNING LIGHT SYSTEM :
Diagnosis Procedure"
.
Headlamp is not turned ON/OFF with the lighting
switch AUTO.
• Combination switch
• Harness between combination
switch and BCM
• BCM
Combination switch
Refer to
• Optical sensor
• Harness between optical sensor
and BCM
• BCM
Optical sensor
Refer to
.
Front fog lamp is not
turned ON.
One side
• Front fog lamp bulb
• Harness between IPDM E/R and
front fog lamp
• IPDM E/R
Front fog lamp circuit
Refer to
.
Both side
Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to
Parking lamp is not turned ON.
• Parking lamp bulb
• Harness between IPDM E/R and
parking lamp
• IPDM E/R
Parking lamp circuit
Refer to
.
Revision: 2011 October
2012 JUKE
EXTERIOR LIGHTING SYSTEM SYMPTOMS
EXL-69
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
WITH DAYTIME RUNNING LIGHT SYSTEM
WITH DAYTIME RUNNING LIGHT SYSTEM : Symptom Table
INFOID:0000000007579211
NOTE:
Perform the self-diagnosis with CONSULT before symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.
Front side marker lamp is not turned ON.
• Front side marker lamp bulb
• Harness between IPDM E/R and
front side marker lamp
Front side marker lamp circuit
Refer to
.
Parking lamp and front side marker lamp are not
turned ON.
• Harness between IPDM E/R and
parking lamp
• IPDM E/R
.
Tail lamp is not turned ON.
• Tail lamp bulb
• Harness between IPDM E/R and
rear combination lamp
.
License plate lamp is not turned ON.
• License plate lamp bulb
• Harness between IPDM E/R and
license plate lamp
License plate lamp circuit
Refer to
.
Tail lamp and license plate lamp are not turned
ON.
Harness between IPDM E/R and
rear combination lamp
.
• Parking lamp, front side marker lamp, tail lamp
and license plate lamp are not turned ON.
• Parking lamp, front side marker lamp, tail lamp
and license plate lamp are not turned OFF.
Symptom diagnosis
“PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE
NOT TURNED ON”
Refer to
.
Tail lamp indicator is not turned ON.
(Exterior lamps are turned ON.)
Combination meter
• Combination meter
Data monitor “LIGHT IND”
• BCM (HEADLAMP)
Active test “TAIL LAMP”
Turn signal lamp does
not blink.
Indicator lamp is nor-
mal.
(Applicable side per-
forms the high flasher
activation.)
• Harness between BCM and each
turn signal lamp
• Turn signal lamp bulb
Turn signal lamp circuit
Refer to
.
Indicator lamp is in-
cluded.
• Combination switch
• Harness between combination
switch and BCM
• BCM
Turn signal indicator
lamp does not blink.
(Turn signal indicator
lamp is normal.)
One side
Combination meter
—
Both sides
(Always)
• Turn signal indicator lamp signal
- BCM
• Combination meter
• Combination meter
Data monitor “TURN IND”
• BCM (FLASHER)
Active test “FLASHER”
Both sides
(Only when activating
hazard warning lamp
with the ignition switch
OFF.)
• Combination meter power supply
and ground circuit
• Combination meter
Combination meter
Power supply and ground circuit
Refer to
.
• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)
• Hazard switch
• Harness between hazard switch
and BCM
• BCM
.
Symptom
Possible cause
Inspection item
Revision: 2011 October
2012 JUKE
EXL-70
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom
Possible cause
Inspection item
Headlamp (HI) is not
turned ON.
One side
• Fuse
• Halogen bulb
• Harness between IPDM E/R and
headlamp
• IPDM E/R
Headlamp (HI) circuit
Refer to
.
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to
High beam indicator lamp is not turned ON.
[Headlamp (HI) is turned ON.]
Combination meter
• Combination meter
Data monitor “HI-BEAM IND”
• BCM (HEADLAMP)
Active test “HEADLAMP”
Headlamp (LO) is not
turned ON.
One side
• Fuse
• Halogen bulb
• Harness between IPDM E/R and
daytime running light relay 1
• Harness between daytime run-
ning light relay 1 and headlamp
• Daytime running light relay 1
• IPDM E/R
Headlamp (LO) circuit
Refer to
RUNNING LIGHT SYSTEM : Com-
ponent Function Check"
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to
Headlamp is not turned
OFF.
When ignition switch
is turned ON.
When ignition switch
is turned OFF.
IPDM E/R
—
Headlamp HI and LO are not turned ON.
• Halogen bulb
• Harness between headlamp and
daytime running light relay 2
• Harness between daytime run-
ning light relay 2 and ground
• Daytime running light relay 2
Headlamp ground circuit
Refer to
TIME RUNNING LIGHT SYSTEM :
Diagnosis Procedure"
.
Daytime running light is not turned ON.
[Headlamp (HI) is turned ON.]
• Fuse
• Harness between IPDM E/R and
daytime running light relay 2
• Daytime running light relay 2
• IPDM E/R
• BCM
• ECM
• Combination meter
• Daytime running light relay circuit
.
• BCM (HEADLAMP)
Data monitor “ENGINE STATE”
• Combination mete
Data monitor “PKB SW”
• BCM (HEADLAMP)
Active test “DAYTIME RUNNING
LIGHT”
Head lamps (both HI and LO) turn ON in the dim-
ming status while daytime running light system is
ON.
Daytime running light relay 1
Daytime running light relay 1
Refer to
RUNNING LIGHT SYSTEM : Com-
ponent Inspection"
.
Front fog lamp is not
turned ON.
One side
• Front fog lamp bulb
• Harness between IPDM E/R and
front fog lamp
• IPDM E/R
Front fog lamp circuit
Refer to
.
Both side
Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to
Parking lamp is not turned ON.
• Parking lamp bulb
• Harness between IPDM E/R and
parking lamp
• IPDM E/R
Parking lamp circuit
Refer to
.
Revision: 2011 October
2012 JUKE
EXTERIOR LIGHTING SYSTEM SYMPTOMS
EXL-71
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Front side marker lamp is not turned ON.
• Front side marker lamp bulb
• Harness between IPDM E/R and
front side marker lamp
Front side marker lamp circuit
Refer to
.
Parking lamp and front side marker lamp are not
turned ON.
• Harness between IPDM E/R and
parking lamp
• IPDM E/R
.
Tail lamp is not turned ON.
• Tail lamp bulb
• Harness between IPDM E/R and
rear combination lamp
.
License plate lamp is not turned ON.
• License plate lamp bulb
• Harness between IPDM E/R and
license plate lamp
License plate lamp circuit
Refer to
.
Tail lamp and license plate lamp are not turned
ON.
Harness between IPDM E/R and
rear combination lamp
.
• Parking lamp, front side marker lamp, tail lamp
and license plate lamp are not turned ON.
• Parking lamp, front side marker lamp, tail lamp
and license plate lamp are not turned OFF.
Symptom diagnosis
“PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE
NOT TURNED ON”
Refer to
.
Tail lamp indicator is not turned ON.
(Exterior lamps are turned ON.)
Combination meter
• Combination meter
Data monitor “LIGHT IND”
• BCM (HEADLAMP)
Active test “TAIL LAMP”
Turn signal lamp does
not blink.
Indicator lamp is nor-
mal.
(Applicable side per-
forms the high flasher
activation.)
• Harness between BCM and each
turn signal lamp
• Turn signal lamp bulb
Turn signal lamp circuit
Refer to
.
Indicator lamp is in-
cluded.
• Combination switch
• Harness between combination
switch and BCM
• BCM
Turn signal indicator
lamp does not blink.
(Turn signal indicator
lamp is normal.)
One side
Combination meter
—
Both sides
(Always)
• Turn signal indicator lamp signal
- BCM
• Combination meter
• Combination meter
Data monitor “TURN IND”
• BCM (FLASHER)
Active test “FLASHER”
Both sides
(Only when activating
hazard warning lamp
with the ignition switch
OFF.)
• Combination meter power supply
and ground circuit
• Combination meter
Combination meter
Power supply and ground circuit
Refer to
.
• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)
• Hazard switch
• Harness between hazard switch
and BCM
• BCM
.
Symptom
Possible cause
Inspection item
Revision: 2011 October
2012 JUKE
EXL-72
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
Description
INFOID:0000000007579212
AUTO LIGHT SYSTEM
The headlamp may not be turned ON/OFF immediately after passing dark area or bright area (short tunnel,
sky bridge, shadowed area etc.) while using the auto light system. This causes the control difference. This is
normal.
Revision: 2011 October
2012 JUKE
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
EXL-73
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
Description
INFOID:0000000007579213
Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.
Diagnosis Procedure
INFOID:0000000007579214
1.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “HL HI REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
BCS-80, "Removal and Installation"
(with Intelligent Key),
(without Intelligent Key).
Monitor item
Condition
Monitor status
HL HI REQ
Lighting switch
(2ND)
HI or PASS
ON
LO
OFF
Revision: 2011 October
2012 JUKE
EXL-74
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
Description
INFOID:0000000007579215
Both side headlamps (LO) are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000007579216
1.
CHECK COMBINATION SWITCH
Check the combination switch. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “HL LO REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
(with Intelligent Key),
(without Intelligent Key).
Monitor item
Condition
Monitor status
HL LO REQ
Lighting switch
2ND
ON
OFF
OFF
Revision: 2011 October
2012 JUKE
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT
TURNED ON
EXL-75
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT
TURNED ON
Description
INFOID:0000000007579217
The parking, license plate, tail, rear side marker lamps and each illumination are not turned ON in any condi-
tion.
Diagnosis Procedure
INFOID:0000000007579218
1.
COMBINATION SWITCH INSPECTION
Check combination switch. Refer to
Is the combination switch normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “TAIL & CLR REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the item status normal?
YES
>> Replace IPDM E/R.
NO
BCS-80, "Removal and Installation"
(with Intelligent Key),
(without Intelligent Key).
Monitor item
Condition
Monitor status
TAIL & CLR REQ
Lighting switch
1ST
ON
OFF
OFF
Revision: 2011 October
2012 JUKE
EXL-76
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
Description
INFOID:0000000007579219
The front fog lamps are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000007579220
1.
CHECK FUSE
Check that the following fuse is fusing.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the applicable circuit. And then replace the fuse.
2.
COMBINATION SWITCH INSPECTION
Check combination switch. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning part.
3.
CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “FR FOG REQ” of IPDM E/R data monitor item.
2.
With operating the front fog lamp switch, check the monitor status.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
(with Intelligent Key),
(without Intelligent Key).
Unit
Location
Fuse No.
Capacity
Front fog lamp
Fuse and fusible link block
#50
15 A
Monitor item
Condition
Monitor status
FR FOG REQ
Front fog lamp switch
(With lighting switch 1ST)
ON
ON
OFF
OFF
Revision: 2011 October
2012 JUKE
HEADLAMP AIMING ADJUSTMENT
EXL-77
< PERIODIC MAINTENANCE >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
PERIODIC MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
Description
INFOID:0000000007579221
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the trunk
room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
JMLIA1338ZZ
A
Headlamp RH (UP/DOWN) adjustment screw B.
Headlamp LH (UP/DOWN) adjustment screw
: Vehicle center
Adjustment screw
Screw driver rotation
Facing direction
A
Headlamp RH (UP/DOWN)
Clockwise
DOWN
Counterclockwise
UP
Revision: 2011 October
2012 JUKE
EXL-78
< PERIODIC MAINTENANCE >
[HALOGEN TYPE]
HEADLAMP AIMING ADJUSTMENT
Aiming Adjustment Procedure
INFOID:0000000007579222
1.
Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
2.
Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the headlamp center and the screen.
3.
Start the engine. Turn the headlamp (LO) ON.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
4.
Measure the distance (X) between the horizontal center line of headlamp (H) and the cutoff line (A) within
the light axis measurement range (R) from the vertical center line ahead of headlamp (V).
Low beam distribution on the screen
5.
Adjust the cutoff line height (X) with the aiming adjustment screw so as to enter in the adjustment range
(M–N) according to the horizontal center line of headlamp (H).
unit: mm (in)
Side view
B
Headlamp LH (UP/DOWN)
Clockwise
DOWN
Counterclockwise
UP
Adjustment screw
Screw driver rotation
Facing direction
Light axis measurement range (R)
: 350
±
175 mm (13.78
±
6.89 in)
JSLIA0005ZZ
Horizontal center line of headlamp (H)
Highest cutoff line height (M)
Lowest cutoff line height (N)
700 (27.56) or less
4 (0.16)
30 (1.18)
701(27.60) – 800 (31.50)
4 (0.16)
30 (1.18)
801 (31.54) or more
17 (0.67)
44 (1.73)
JSLIA0006ZZ
Distance between the headlamp center and the screen (L)
: 10 m (32.8 ft)
Revision: 2011 October
2012 JUKE
FRONT FOG LAMP AIMING ADJUSTMENT
EXL-79
< PERIODIC MAINTENANCE >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP AIMING ADJUSTMENT
Description
INFOID:0000000007579223
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the trunk
room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
• Turn the aiming adjusting screw for adjustment.
• For the position and direction of the adjusting screw, refer to the
figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.
Aiming Adjustment Procedure
INFOID:0000000007579224
1.
Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
2.
Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.
3.
Start the engine. Turn the front fog lamp ON.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
4.
Adjust the cutoff line height (A) with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and (A) becomes 150 mm (5.91 in).
A: UP
B: DOWN
JMLIA1249ZZ
Revision: 2011 October
2012 JUKE
EXL-80
< PERIODIC MAINTENANCE >
[HALOGEN TYPE]
FRONT FOG LAMP AIMING ADJUSTMENT
Front fog lamp light distribution on the screen
JPLIA0008ZZ
A
: Cutoff line
B
: High illuminance area
H
: Horizontal center line of front fog lamp
V
: Vertical center line of front fog lamp
X
: Cutoff line height
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст