Nissan Juke (2012 year). Service Repair Manual — part 185
PWC-48
< REMOVAL AND INSTALLATION >
POWER WINDOW MAIN SWITCH
REMOVAL AND INSTALLATION
POWER WINDOW MAIN SWITCH
Removal and Installation
INFOID:0000000007579924
REMOVAL
1.
Remove power window main switch finisher. Refer to
INT-12, "Removal and Installation"
.
2.
Remove power window main switch (1) from power window
main switch finisher (2) using flat-head screw driver (A).
CAUTION:
Do not fold the pawl of power window main switch finisher.
NOTE:
The same procedure is also performed for front power window
switch (passenger side) and rear power window switch (LH & RH).
INSTALLATION
Install in the reverse order of removal.
NOTE:
If power window main switch is replaced or is removed, it is necessary to perform the initialization procedure.
Refer to
: Pawl
JMKIA6199ZZ
Revision: 2011 October
2012 JUKE
PWO
PWO-1
ELECTRICAL & POWER CONTROL
C
D
E
F
G
H
I
J
K
L
B
SECTION
PWO
A
O
P
N
CONTENTS
POWER OUTLET
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
WIRING DIAGRAM . . . . . . . . . ...
POWER SOCKET . . . . . . . . . . . ..
Wiring Diagram . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . .
POWER SOCKET . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Revision: 2011 October
2012 JUKE
PWO-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000007577757
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Revision: 2011 October
2012 JUKE
PWO
POWER SOCKET
PWO-3
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
WIRING DIAGRAM
POWER SOCKET
Wiring Diagram
INFOID:0000000007577758
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JCMWA6063GB
Revision: 2011 October
2012 JUKE
PWO-4
< REMOVAL AND INSTALLATION >
POWER SOCKET
REMOVAL AND INSTALLATION
POWER SOCKET
Exploded View
INFOID:0000000007577759
Removal and Installation
INFOID:0000000007577760
REMOVAL
1.
Remove cluster tray. Refer to
IP-12, "Removal and Installation"
2.
Pull out inner socket (1) by pushing the pawl (B) of the ring (2)
from the inner socket hole (square) (A).
3.
Press the ring pawl from the back of the cluster tray to remove
the ring.
INSTALLATION
Note the following, and install in the reverse order of removal.
JSMIA0455ZZ
1
: Inner socket
2
: Ring
JSMIA0357ZZ
: Pawl
JSMIA0358ZZ
Revision: 2011 October
2012 JUKE
PWO
POWER SOCKET
PWO-5
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Align the cut outs of inner socket, ring and cluster tray.
A
: Cut out
JSMIA0359ZZ
Revision: 2011 October
2012 JUKE
RAX-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
RAX
A
B
RAX
N
O
P
CONTENTS
REAR AXLE
2WD
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tools . . . . . . . . . ....
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
REAR WHEEL HUB . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
REAR WHEEL HUB . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . ...
Wheel Bearing . . . . . . . . . . . . . . ...
AWD
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Drive Shaft . . . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tools . . . . . . . . . ....
SYMPTOM DIAGNOSIS . . . . . . . ..
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . ...
NVH Troubleshooting Chart . . . . . . . . .
PERIODIC MAINTENANCE . . . . . .
REAR WHEEL HUB AND HOUSING . . . ...
Inspection . . . . . . . . . . . . . . . .
REAR DRIVE SHAFT . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
REAR WHEEL HUB AND HOUSING . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
REAR DRIVE SHAFT . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
WHEEL SIDE . . . . . . . . . . . . . . . .
WHEEL SIDE : Disassembly and Assembly . . ...
FINAL DRIVE SIDE . . . . . . . . . . . . .
FINAL DRIVE SIDE : Disassembly and Assembly .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Bearing . . . . . . . . . . . . . . .
Drive Shaft . . . . . . . . . . . . . . . ...
Revision: 2011 October
2012 JUKE
RAX-2
< PREPARATION >
[2WD]
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000007580039
Tool name
Description
Power tool
Loosening bolts and nuts
Ball joint remover
Removing hub bolt
PBIC0190E
NT146
Revision: 2011 October
2012 JUKE
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
RAX-3
< SYMPTOM DIAGNOSIS >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000007580040
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference
—
NVH
in
RAX and RSU sections
NVH in WT section
NVH in WT section
NVH in BR section
Possible cause and SUSPECTED PARTS
Im
p
rop
er i
n
s
ta
lla
tio
n
,
lo
os
en
es
s
P
a
rt
s interference
W
he
el be
arin
g da
ma
ge
REA
R
AXLE AND REAR S
U
SPENSION
TI
RE
ROAD W
H
EEL
BR
AK
E
Symptom
REAR AXLE
Noise
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
Shimmy
×
×
×
×
×
×
Judder
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
Revision: 2011 October
2012 JUKE
RAX-4
< PERIODIC MAINTENANCE >
[2WD]
REAR WHEEL HUB
PERIODIC MAINTENANCE
REAR WHEEL HUB
Inspection
INFOID:0000000007580041
COMPONENT PART
Check the mounting conditions (looseness, back lash) of each component and component conditions (wear,
damage) are normal.
WHEEL HUB ASSEMBLY (BEARING-INTEGRATED TYPE)
Check the following items, and replace the part it necessary.
• Move wheel hub assembly in the axial direction by hand. Check there is no looseness of wheel bearing.
• Rotate wheel hub assembly and check there is no unusual noise or other irregular conditions. If there is any
of irregular conditions, replace wheel hub assembly.
Axial end play
: Refer to
.
Revision: 2011 October
2012 JUKE
REAR WHEEL HUB
RAX-5
< REMOVAL AND INSTALLATION >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
REMOVAL AND INSTALLATION
REAR WHEEL HUB
Exploded View
INFOID:0000000007580042
Removal and Installation
INFOID:0000000007580043
REMOVAL
1.
Remove tires with power tool. Refer to
WT-43, "Removal and Installation"
.
2.
Remove wheel sensor. Refer to
BRC-129, "REAR WHEEL SENSOR : Removal and Installation"
.
3.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to
BR-53, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
CAUTION:
Never depress brake pedal while brake caliper is removed.
4.
Remove disc rotor. If disc rotor cannot be removed, remove as follows.
CAUTION:
• Parking brake completely in the released position.
• Put matching marks (A) on the wheel hub assembly and
the disc rotor before removing the disc rotor.
• Never drop disc rotor.
a.
Fix the disc rotor with wheel nuts and remove the adjusting hole
plug.
1.
Rear suspension beam
2.
Parking brake assembly
3.
Hub bolt
4.
Wheel hub assembly (Bearing-inte-
grated type)
5.
Disc rotor
6.
Plug
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JPDIG0203GB
JPDIG0066ZZ
Revision: 2011 October
2012 JUKE
RAX-6
< REMOVAL AND INSTALLATION >
[2WD]
REAR WHEEL HUB
b.
Using suitable tool, rotate adjuster (1) in the direction (A) to
retract and loosen brake shoe.
c.
Remove disc rotor.
5.
Remove wheel hub assembly.
CAUTION:
Never remove parking brake assembly. Protect it from fall-
ing.
6.
Remove hub bolts (1) from wheel hub assembly, using the ball
joint remover (A) (commercial service tool).
CAUTION:
• Remove hub bolt only when necessary.
• Never hammer the hub bolt to avoid impact to the wheel
hub assembly.
• Pull out the hub bolt in a direction perpendicular to the
wheel hub assembly.
7.
Perform inspection after removal. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Place a washer (A) as shown in the figure to install the hub bolts
(1) by using the tightening force of the nut (B).
CAUTION:
• Check that there is no clearance between wheel hub assem-
bly and hub bolt.
• Never reuse hub bolt.
• Align the matching marks that have been made during removal
when reusing the disc rotor.
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000007580044
INSPECTION AFTER REMOVAL
Check the wheel hub assembly for wear, cracks, and damage. Replace if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection.
BRC-129, "REAR WHEEL SENSOR : Removal and
.
2.
Adjust parking brake operation (stroke). Refer to
PB-10, "Inspection and Adjustment"
3.
Check wheel alignment. Refer to
JPDIG0204ZZ
JPDIF0299ZZ
JPDIF0300ZZ
Revision: 2011 October
2012 JUKE
SERVICE DATA AND SPECIFICATIONS (SDS)
RAX-7
< SERVICE DATA AND SPECIFICATIONS (SDS)
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000007580045
Item
Standard
Axial end play
0.05 mm (0.002 in) or less
Revision: 2011 October
2012 JUKE
RAX-8
< PRECAUTION >
[AWD]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precautions for Drive Shaft
INFOID:0000000007580046
• Observe the following precautions when disassembling and assembling drive shaft.
- Never disassemble joint sub-assembly because it is non-overhaul parts.
- Perform work in a location which is as dust-free as possible.
- Clean the parts, before disassembling and assembling.
- Prevent the entry of foreign objects during disassembly of the service location.
- Reassemble disassembled parts carefully in the correct order. If work is interrupted, a clean cover must be
placed over parts.
- Use paper waste. Fabric shop cloths must not be used because of the danger of lint adhering to parts.
- Clean disassembled parts (except for rubber parts) with kerosene which shall be removed by blowing with
air or wiping with paper waste.
Revision: 2011 October
2012 JUKE
PREPARATION
RAX-9
< PREPARATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000007580047
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000007580048
Tool number
(Kent-More No.)
Tool name
Description
KV38100500
(
—
)
Drift
a: 80 mm (3.15 in) dia.
b: 60 mm (2.36 in) dia.
Installing sensor rotor
KV40101840
(
—
)
Color
a: 67 mm (2.64 in) dia.
b: 85 mm (3.35 in) dia.
Installing sensor rotor
KV40107300
(
—
)
Boot band crimping tool
Installing boot band
KV38107900
(
—
)
Protector
a: 32 mm (1.26 in) dia.
Installing drive shaft
ZZA0701D
ZZA1113D
ZZA1229D
PDIA1183J
Revision: 2011 October
2012 JUKE
RAX-10
< PREPARATION >
[AWD]
PREPARATION
Tool name
Description
Power tool
Loosening bolts and nuts
Drive shaft puller
Removing drive shaft joint sub assembly
Ball joint remover
Removing hub bolt
PBIC0190E
JPDIG0152ZZ
NT146
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст