Nissan Juke (2012 year). Service Repair Manual — part 184
PWC-32
< DTC/CIRCUIT DIAGNOSIS >
POWER WINDOW MOTOR
NO
>> Refer to
PWC-32, "REAR RH : Diagnosis Procedure"
.
REAR RH : Diagnosis Procedure
INFOID:0000000007579906
1.
CHECK REAR POWER WINDOW MOTOR RH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear power window motor RH connector.
3.
Turn ignition switch ON.
4.
Check voltage between rear power window motor RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear power window motor RH.
NO
>> GO TO 2.
2.
CHECK REAR POWER WINDOW MOTOR RH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect rear power window switch RH connector.
3.
Check continuity between rear power window motor RH harness connector and rear power window switch
RH harness connector.
4.
Check continuity between rear power window motor RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear power window switch RH.
NO
>> Repair or replace harness.
(+)
(-)
Condition
Voltage (V)
Rear power window motor RH
Connector
Terminal
D47
1
Ground
Rear power window
switch RH
NEUTRAL
0 – 1
DOWN
9 – 16
3
NEUTRAL
0 – 1
UP
9 – 16
Rear power window motor RH
Rear power window switch RH
Continuity
Connector
Terminal
Connector
Terminal
D47
1
D43
4
Existed
3
5
Rear power window motor RH
Ground
Continuity
Connector
Terminal
D47
1
Not existed
3
Revision: 2011 October
2012 JUKE
ENCODER CIRCUIT
PWC-33
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
ENCODER CIRCUIT
Component Function Check
INFOID:0000000007579907
1.
CHECK FUNCTION
Check that front driver side door glass perform AUTO UP/DOWN operation normally when power window
main switch is operated.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007579908
1.
CHECK ENCODER PULSE SIGNAL
1.
Turn ignition switch ON.
2.
Check signal between power window main switch harness connector and ground with oscilloscope.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-48, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK ENCODER SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector and front power window motor (driver side) connector.
3.
Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.
4.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
(+)
(-)
Signal
(Reference value)
Power window main switch
Connector
Terminal
D35
4
Ground
Refer to the following signal
5
JMKIA5210GB
Power window main switch
Front power window motor (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D35
4
D37
5
Existed
5
4
Power window main switch
Ground
Continuity
Connector
Terminal
D35
4
Not existed
5
Revision: 2011 October
2012 JUKE
PWC-34
< DTC/CIRCUIT DIAGNOSIS >
ENCODER CIRCUIT
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK ENCODER POWER SUPPLY
1.
Connect power window main switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between front power window motor (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK ENCODER POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector.
3.
Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.
4.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-48, "Removal and Installation"
NO
>> Repair or replace harness.
5.
CHECK ENCODER GROUND CIRCUIT 1
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector.
3.
Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.
4.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK ENCODER GROUND CIRCUIT 2
1.
Connect power window main switch connector.
(+)
(-)
Voltage (V)
Front power window motor (driver side)
Connector
Terminal
D37
1
Ground
9 – 16
Power window main switch
Front power window motor (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D35
14
D37
1
Existed
Power window main switch
Ground
Continuity
Connector
Terminal
D35
14
Not existed
Power window main switch
Front power window motor (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D35
12
D37
6
Existed
Power window main switch
Ground
Continuity
Connector
Terminal
D35
12
Not existed
Revision: 2011 October
2012 JUKE
ENCODER CIRCUIT
PWC-35
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
2.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window motor (driver side).
NO
>> Replace power window main switch. Refer to
PWC-48, "Removal and Installation"
Power window main switch
Ground
Continuity
Connector
Terminal
D35
12
Existed
Revision: 2011 October
2012 JUKE
PWC-36
< SYMPTOM DIAGNOSIS >
NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY SWITCH
SYMPTOM DIAGNOSIS
NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY
SWITCH
Diagnosis Procedure
INFOID:0000000007579909
1.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Check BCM power supply and ground circuit. Refer to the following.
• With Intelligent Key: Refer to
• Without Intelligent Key: Refer to
BCS-134, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY AND GROUND CIRCUIT
Check power window main switch power supply and ground circuit.
Refer to
PWC-22, "POWER WINDOW MAIN SWITCH : Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2011 October
2012 JUKE
DRIVER SIDE POWER WINDOW DOES NOT OPERATE
PWC-37
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
DRIVER SIDE POWER WINDOW DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000007579910
1.
CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE)
Check front power window motor (driver side).
Refer to
PWC-29, "DRIVER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2011 October
2012 JUKE
PWC-38
< SYMPTOM DIAGNOSIS >
FRONT PASSENGER SIDE POWER WINDOW DOES NOT OPERATE
FRONT PASSENGER SIDE POWER WINDOW DOES NOT OPERATE
WHEN BOTH POWER WINDOW MAIN SWITCH AND FRONT POWER WINDOW
SWITCH ARE OPERATED
WHEN BOTH POWER WINDOW MAIN SWITCH AND FRONT POWER WINDOW
SWITCH ARE OPERATED : Diagnosis Procedure
INFOID:0000000007579911
1.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
Check front power window switch (passenger side).
Refer to
PWC-25, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE)
Check front power window motor (passenger side).
Refer to
PWC-30, "PASSENGER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
WHEN FRONT POWER WINDOW SWITCH (PASSENGER SIDE) IS OPERATED
WHEN FRONT POWER WINDOW SWITCH (PASSENGER SIDE) IS OPERATED :
Diagnosis Procedure
INFOID:0000000007579912
1.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) POWER SUPPLY AND GROUND CIR-
CUIT
Check front power window switch (passenger side) power supply and ground circuit.
Refer to
PWC-23, "FRONT POWER WINDOW SWITCH (PASSENGER SIDE) : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
Check front power window switch (passenger side).
Refer to
PWC-25, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
WHEN POWER WINDOW MAIN SWITCH IS OPERATED
Revision: 2011 October
2012 JUKE
FRONT PASSENGER SIDE POWER WINDOW DOES NOT OPERATE
PWC-39
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
WHEN POWER WINDOW MAIN SWITCH IS OPERATED : Diagnosis Procedure
INFOID:0000000007579913
1.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
Check front power window switch (passenger side).
Refer to
PWC-25, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2011 October
2012 JUKE
PWC-40
< SYMPTOM DIAGNOSIS >
REAR LH SIDE POWER WINDOW DOES NOT OPERATE
REAR LH SIDE POWER WINDOW DOES NOT OPERATE
WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW
SWITCH LH ARE OPERATED
WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW
SWITCH LH ARE OPERATED : Diagnosis Procedure
INFOID:0000000007579914
1.
CHECK REAR POWER WINDOW SWITCH LH
Check rear power window switch LH.
Refer to
PWC-27, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK REAR POWER WINDOW MOTOR LH
Check rear power window motor LH.
Refer to
PWC-30, "REAR LH : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
WHEN REAR POWER WINDOW SWITCH LH IS OPERATED
WHEN REAR POWER WINDOW SWITCH LH IS OPERATED : Diagnosis Procedure
INFOID:0000000007579915
1.
CHECK REAR POWER WINDOW SWITCH LH POWER SUPPLY AND GROUND CIRCUIT
Check rear power window switch LH power supply and ground circuit.
Refer to
PWC-23, "REAR POWER WINDOW SWITCH : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK REAR POWER WINDOW SWITCH LH
Check rear power window switch LH.
Refer to
PWC-27, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
WHEN POWER WINDOW MAIN SWITCH IS OPERATED
Revision: 2011 October
2012 JUKE
REAR LH SIDE POWER WINDOW DOES NOT OPERATE
PWC-41
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
WHEN POWER WINDOW MAIN SWITCH IS OPERATED : Diagnosis Procedure
INFOID:0000000007579916
1.
CHECK REAR POWER WINDOW SWITCH LH
Check rear power window switch LH.
Refer to
PWC-27, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2011 October
2012 JUKE
PWC-42
< SYMPTOM DIAGNOSIS >
REAR RH SIDE POWER WINDOW DOES NOT OPERATE
REAR RH SIDE POWER WINDOW DOES NOT OPERATE
WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW
SWITCH RH ARE OPERATED
WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW
SWITCH RH ARE OPERATED : Diagnosis Procedure
INFOID:0000000007579917
1.
CHECK REAR POWER WINDOW SWITCH RH
Check rear power window switch RH.
Refer to
PWC-27, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK REAR POWER WINDOW MOTOR RH
Check rear power window motor RH.
Refer to
PWC-31, "REAR RH : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
WHEN REAR POWER WINDOW SWITCH RH IS OPERATED
WHEN REAR POWER WINDOW SWITCH RH IS OPERATED : Diagnosis Procedure
INFOID:0000000007579918
1.
CHECK REAR POWER WINDOW SWITCH RH POWER SUPPLY AND GROUND CIRCUIT
Check rear power winodw switch RH power supply and ground circuit.
Refer to
PWC-23, "REAR POWER WINDOW SWITCH : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK REAR POWER WINDOW SWITCH RH
Check rear power window switch RH.
Refer to
PWC-27, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
WHEN POWER WINDOW MAIN SWITCH IS OPERATED
Revision: 2011 October
2012 JUKE
REAR RH SIDE POWER WINDOW DOES NOT OPERATE
PWC-43
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
WHEN POWER WINDOW MAIN SWITCH IS OPERATED : Diagnosis Procedure
INFOID:0000000007579919
1.
CHECK REAR POWER WINDOW SWITCH RH
Check rear power window switch RH.
Refer to
PWC-27, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2011 October
2012 JUKE
PWC-44
< SYMPTOM DIAGNOSIS >
AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATE NORMAL-
LY (DRIVER SIDE)
AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATE NOR-
MALLY (DRIVER SIDE)
Diagnosis Procedure
INFOID:0000000007579920
1.
PERFORM INITIALIZATION PROCEDURE
Initialization procedure is executed and operation is confirmed.
Refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK ENCODER CIRCUIT
Check encoder circuit.
Refer to
PWC-33, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2011 October
2012 JUKE
ANTI-PINCH SYSTEM DOES NOT OPERATE NORMALLY (DRIVER SIDE)
PWC-45
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
ANTI-PINCH SYSTEM DOES NOT OPERATE NORMALLY (DRIVER SIDE)
Diagnosis Procedure
INFOID:0000000007579921
1.
CHECK POWER WINDOW AUTO OPERATION
Check AUTO operation when anti-pinch function does not operate.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2011 October
2012 JUKE
PWC-46
< SYMPTOM DIAGNOSIS >
POWER WINDOW RETAINED POWER OPERATION DOES NOT OPERATE
PROPERLY
POWER WINDOW RETAINED POWER OPERATION DOES NOT OPER-
ATE PROPERLY
Diagnosis Procedure
INFOID:0000000007579922
1.
CHECK FRONT DOOR SWITCH
Check front door switch. Refer to the following.
• With Intelligent Key: Refer to
DLK-71, "Component Function Check"
• Without Intelligent Key: Refer to
DLK-201, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-43, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2011 October
2012 JUKE
POWER WINDOW LOCK SWITCH DOES NOT FUNCTION
PWC-47
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
POWER WINDOW LOCK SWITCH DOES NOT FUNCTION
Diagnosis Procedure
INFOID:0000000007579923
1.
REPLACE POWER WINDOW MAIN SWITCH
Replace power window main switch.
>> Refer to
PWC-48, "Removal and Installation"
.
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст