Nissan Juke (2012 year). Service Repair Manual — part 150
INL-34
< DTC/CIRCUIT DIAGNOSIS >
LUGGAGE ROOM LAMP CIRCUIT
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> Repair or replace harnesses.
BCM
Ground
Continuity
Connector
Terminal
B10
49
Not existed
BCM
Ground
Continuity
Connector
Terminal
B9
55
Not existed
Revision: 2011 October
2012 JUKE
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
INL-35
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
Description
INFOID:0000000007578763
Provides the power supply and the ground to control the push-button ignition switch illumination.
Component Function Check
INFOID:0000000007578764
1.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION OPERATION
CONSULT ACTIVE TEST
1.
Turn the ignition switch ON.
2.
Select “ENGINE SW ILLUMI” of BCM (INTELLIGENT KEY) active test item.
3.
With operating the test items, check that the push-button ignition switch illumination turns ON/OFF.
Does the push-button ignition switch illumination turn ON/OFF?
YES
>> Push-button ignition switch illumination circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007578765
1.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY OUTPUT
1.
Turn ignition switch OFF.
2.
Disconnect push-button ignition switch connector.
3.
Check voltage between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY OPEN CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and the push-button ignition switch harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harnesses.
3.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY SHORT CIRCUIT
Check continuity between BCM harness connector and ground.
On
: Push-button ignition switch illumination ON
Off
: Push-button ignition switch illumination OFF
(+)
(–)
Condition
Voltage
(Approx.)
Push-button ignition switch
Connector
Terminal
M101
5
Ground
Push-button ignition switch
illumination
ON
12 V
OFF
0 V
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M70
90
M101
5
Existed
BCM
Ground
Continuity
Connector
Terminal
M70
90
Not existed
Revision: 2011 October
2012 JUKE
INL-36
< DTC/CIRCUIT DIAGNOSIS >
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> Repair or replace harnesses.
4.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION GROUND CIRCUIT
1.
Turn the ignition switch OFF.
2.
Check continuity between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace push-button ignition switch.
NO
>> Repair or replace harnesses.
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M101
6
Existed
Revision: 2011 October
2012 JUKE
INTERIOR LIGHTING SYSTEM SYMPTOMS
INL-37
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
SYMPTOM DIAGNOSIS
INTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000007578766
NOTE:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.
Symptom
Possible cause
Inspection item
All the following lamps do not turn ON.
• Map lamp
• Luggage room lamp
• Harness between BCM and each
interior room lamp
• BCM
Interior room lamp power supply cir-
cuit
Refer to
.
• Interior room lamp does not turn ON even
though the door is open.
(It turns ON when turning the interior room
lamp ON.)
• Interior room lamp does not turn OFF even
though the door is closed.
• Harness between BCM and each
door switch
• Harness between BCM and each
interior room lamp
• BCM
Door switch circuit
Refer to
.
Interior room lamp control circuit
Refer to
.
Interior room lamp timer does not activate.
(It turns ON/ OFF when the door opens/closes.)
—
Check the interior room lamp setting.
Refer to
.
• Luggage room lamp does not turn ON even
though the back door is open.
• Luggage room lamp does not turn OFF even
though the back door is closed.
• Harness between BCM and back
door switch
• Harness between BCM and lug-
gage room lamp
• BCM
Back door switch circuit
Refer to
.
Luggage room lamp circuit
Refer to
.
Push-button ignition switch illumination does not
illuminate.
• Harness between BCM and push-
button ignition switch
• BCM
Push-button ignition switch illumina-
tion circuit
Refer to
.
Interior room lamp battery saver does not acti-
vate.
BCM
Replace BCM.
Refer to
Revision: 2011 October
2012 JUKE
INL-38
< REMOVAL AND INSTALLATION >
MAP LAMP
REMOVAL AND INSTALLATION
MAP LAMP
Exploded View
INFOID:0000000007578767
Removal and Installation
INFOID:0000000007578768
CAUTION:
Disconnect the battery negative terminal or the fuse.
REMOVAL
1.
Remove the lens (1).
• Insert a remover tool (A) into the gap between the lens.
• Disengage the lens fixing pawls, and then remove the lens.
CAUTION:
Use a remover tool wrapped in tape.
2.
Press pawl in the direction shown by the arrow in the figure
using a remover tool (A), and then pull the map lamp housing (1)
in the direction shown by the arrow in the figure.
CAUTION:
Use a remover tool wrapped in tape.
3.
Disconnect map lamp harness connector, and then remove map lamp housing.
INSTALLATION
1.
Map lamp bulb housing
2.
Bulb
3.
Lens
: Pawl
JMLIA1062ZZ
: Pawl
JMLIA1063ZZ
: Pawl
JMLIA1064ZZ
Revision: 2011 October
2012 JUKE
MAP LAMP
INL-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
Install in the reverse order of removal.
Replacement
INFOID:0000000007578769
CAUTION:
• Disconnect battery negative terminal or the fuse.
• Never touch glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
MAP LAMP BULB
1.
Remove the lens (1).
• Insert a remover tool (A) into the gap between the lens.
• Disengage the lens fixing pawls, and then remove the lens.
CAUTION:
Use a remover tool wrapped in tape.
2.
Remove the bulb.
: Pawl
JMLIA1063ZZ
Revision: 2011 October
2012 JUKE
INL-40
< REMOVAL AND INSTALLATION >
GLOVE BOX LAMP
GLOVE BOX LAMP
Exploded View
INFOID:0000000007958593
Removal and Installation
INFOID:0000000007958594
Replacement
INFOID:0000000007958595
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse while performing the opera-
tion to prevent electric leakage.
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to the bulb.
• Never touch the glass surface of the bulb with bare hands because the surface is very hot just after
the lamp is turned OFF to prevent a burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (causing dirty or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
GLOVE BOX LAMP BULB
1.
Remove glove box assembly. Refer to
IP-12, "Removal and Installation"
1.
Bulb & socket assembly
2.
Lamp housing
3.
Glove box assembly
: Pawl
: Vehicle front
JMLIA2678ZZ
Revision: 2011 October
2012 JUKE
GLOVE BOX LAMP
INL-41
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
2.
Rotate the bulb & socket assembly counterclockwise and unlock
it, and then remove bulb & socket assembly.
JMLIA1528ZZ
Revision: 2011 October
2012 JUKE
INL-42
< REMOVAL AND INSTALLATION >
LUGGAGE ROOM LAMP
LUGGAGE ROOM LAMP
Exploded View
INFOID:0000000007578770
Removal and Installation
INFOID:0000000007578771
CAUTION:
Disconnect the battery cable from negative terminal or remove the fuse.
REMOVAL
1.
Insert a remover tool (A) into the gap between luggage room
lamp and luggage side lower finisher RH.
2.
Disengage luggage room lamp fixing pawl, and then disconnect
luggage room lamp harness connector.
3.
Remove luggage room lamp from luggage side lower finisher
RH.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000007578772
CAUTION:
• Disconnect the battery cable from negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily substaces away from it.
Never touch bulb by hand while it is lit or right after it is off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with a new one.
LUGGAGE ROOM LAMP BULB
1.
Remove the luggage room lamp.
1.
Bulb housing
2.
Bulb
3.
Lens
: Pawl
JMLIA1238ZZ
: Pawl
JMLIA1280ZZ
Revision: 2011 October
2012 JUKE
LUGGAGE ROOM LAMP
INL-43
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
2.
Insert a remover tool (A) into the gap between the lens and bulb
housing, and then disengage fixing pawls as shown by the arrow
in the figure.
3.
Remove the bulb.
: Pawl
JMLIA1239ZZ
Revision: 2011 October
2012 JUKE
INL-44
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb Specifications
INFOID:0000000007578773
*: With intelligent key
Item
Type
Wattage (W)
Push-button ignition switch illumination*
LED
—
Map lamp
W5W
5
Glove box lamp
Wedge
1.4
Luggage room lamp
—
5
Revision: 2011 October
2012 JUKE
INT-1
BODY INTERIOR
C
D
E
F
G
H
I
K
L
M
SECTION
INT
A
B
INT
N
O
P
CONTENTS
INTERIOR
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Procedure without Cowl Top Cover
. ..
Precaution for Work . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ....
Commercial Service Tools . . . . . . . . . ....
CLIP LIST . . . . . . . . . . . . . . .
Clip List . . . . . . . . . . . . . . . . .....
SYMPTOM DIAGNOSIS . . . . . . . ...
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES . . . . . . . . . . . . . . . .
Work Flow . . . . . . . . . . . . . . . .....
Inspection Procedure . . . . . . . . . . . ....
Diagnostic Worksheet . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
FRONT DOOR FINISHER . . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
REAR DOOR FINISHER . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
BODY SIDE TRIM . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
FRONT PILLAR GARNISH . . . . . . . . . ...
FRONT PILLAR GARNISH : Removal and Instal-
lation . . . . . . . . . . . . . . . . . .
KICKING PLATE INNER . . . . . . . . . . ...
KICKING PLATE INNER : Removal and Installa-
tion . . . . . . . . . . . . . . . . . . ...
DASH SIDE FINISHER . . . . . . . . . . . ..
DASH SIDE FINISHER : Removal and Installation
.
BODY SIDE WELT . . . . . . . . . . . . . .
BODY SIDE WELT : Removal and Installation . .
CENTER PILLAR LOWER GARNISH . . . . . ...
CENTER PILLAR LOWER GARNISH : Removal
and Installation . . . . . . . . . . . . . .
CENTER PILLAR UPPER GARNISH . . . . . .
CENTER PILLAR UPPER GARNISH : Removal
and Installation . . . . . . . . . . . . . .
FLOOR TRIM . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
HEADLINING . . . . . . . . . . . . .
NORMAL ROOF . . . . . . . . . . . . . .
NORMAL ROOF : Exploded View . . . . . . ...
NORMAL ROOF : Removal and Installation . . ...
SUNROOF . . . . . . . . . . . . . . . . ..
SUNROOF : Exploded View . . . . . . . . .
SUNROOF : Removal and Installation . . . . .
LUGGAGE FLOOR TRIM . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
LUGGAGE REAR PLATE . . . . . . . . . . .
LUGGAGE REAR PLATE : Removal and Installa-
tion . . . . . . . . . . . . . . . . . . ...
LUGGAGE SIDE LOWER FINISHER . . . . . .
LUGGAGE SIDE LOWER FINISHER : Removal
and Installation . . . . . . . . . . . . . .
Revision: 2011 October
2012 JUKE
INT-2
LUGGAGE SIDE UPPER FINISHER . . . . . ....
LUGGAGE SIDE UPPER FINISHER : Removal
and Installation . . . . . . . . . . . . . ...
BACK DOOR TRIM . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . ....
BACK DOOR PULL HANDLE . . . . . . . . ..
BACK DOOR PULL HANDLE : Removal and In-
stallation . . . . . . . . . . . . . . . . .
BACK DOOR LOWER FINISHER . . . . . . . .
BACK DOOR LOWER FINISHER : Removal and
Installation . . . . . . . . . . . . . . . ...
BACK DOOR SIDE FINISHER . . . . . . . . ..
BACK DOOR SIDE FINISHER : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
EMERGENCY LID . . . . . . . . . . . . . .
EMERGENCY LID : Removal and Installation . .
Revision: 2011 October
2012 JUKE
PRECAUTIONS
INT-3
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000007576745
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000007576746
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Precaution for Work
INFOID:0000000007576747
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operation.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
PIIB3706J
Revision: 2011 October
2012 JUKE
INT-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000007576748
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000007576749
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-43980)
NISSAN Squeak and Rattle
Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes clips, pawls and metal clips
SIIA0995E
JMKIA3050ZZ
Revision: 2011 October
2012 JUKE
CLIP LIST
INT-5
< PREPARATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
CLIP LIST
Clip List
INFOID:0000000007576750
JMJIA3734GB
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст