Nissan Juke (2012 year). Service Repair Manual — part 149
INL-18
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
ACTIVE TEST
BATTERY SAVER
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)
INFOID:0000000007578749
WORK SUPPORT
Monitor item
[Unit]
Description
IGN ON SW
[On/Off]
Ignition switch (ON) status judeges from IGN signal (ignition power supply)
KEY ON SW
[On/Off]
The switch status input from key switch
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]
The switch status input from rear door switch LH
BACK DOOR SW
[On/Off]
The switch status input from back door switch
LOCK STATUS
[On/Off]
The switch status input from door lock status switch (driver side)
CDL LOCK SW
[On/Off]
Lock switch status input from door lock and unlock switch
CDL UNLOCK SW
[On/Off]
Unlock switch status input from door lock and unlock switch
KEYLESS LOCK
[On/Off]
Lock signal status received from remote keyless entry receiver
KEYLESS UNLOCK
[On/Off]
Unlock signal status received from remote keyless entry receiver
TRNK/HAT MNTR
[On/Off]
NOTE:
The item is indicated, but not monitored
KEY CYL LK-SW
[On/Off]
Lock switch status received from key cylinder switch
KEY CYL UN-SW
[On/Off]
Unlock switch status received from key cylinder switch
ACC ON SW
[On/Off]
Ignition switch (ACC) status judges from ACC signal (ACC power supply)
Test item
Operation
Description
INT LAMP
On
Outputs the interior room lamp control signal to turn the interior room lamps ON.
[Map lamp, room lamp (when applicable lamps switch is in DOOR position.)]
Off
Stops the interior room lamp control signal to turn the interior room lamps.
Service item
Setting item
Setting
ROOM LAMP TIMER SET
MODE 1
30 min.
Sets the interior room lamp battery saver timer operating
time.
MODE 2
60 min.
MODE 3
*
15 min.
Revision: 2011 October
2012 JUKE
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
INL-19
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
*:Factory setting
DATA MONITOR
ACTIVE TEST
*: Each lamp switch is in ON position.
ROOM LAMP BAT SAV SET
On
*
With the interior room lamp battery saver function
Off
Without the interior room lamp battery saver function
Service item
Setting item
Setting
Monitor item
[Unit]
Description
IGN ON SW
[On/Off]
Ignition switch (ON) status judeges from IGN signal (ignition power supply)
KEY ON SW
[On/Off]
The switch status input from key switch
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]
The switch status input from rear door switch LH
BACK DOOR SW
[On/Off]
The switch status input from back door switch
LOCK STATUS
[On/Off]
The switch status input from door lock status switch (driver side)
CDL LOCK SW
[On/Off]
Lock switch status input from door lock and unlock switch
CDL UNLOCK SW
[On/Off]
Unlock switch status input from door lock and unlock switch
KEYLESS LOCK
[On/Off]
Lock signal status received from remote keyless entry receiver
KEYLESS UNLOCK
[On/Off]
Unlock signal status received from remote keyless entry receiver
TRNK/HAT MNTR
[On/Off]
NOTE:
The item is indicated, but not monitored
KEY CYL LK-SW
[On/Off]
Lock switch status received from key cylinder switch
KEY CYL UN-SW
[On/Off]
Unlock switch status received from key cylinder switch
ACC ON SW
[On/Off]
Ignition switch (ACC) status judges from ACC signal (ACC power supply)
Test item
Operation
Description
BATTERY SAVER
Off
Cuts the interior room lamp power supply to turn interior room lamps OFF.
On
Outputs the interior room lamp power supply to turn interior room lamps ON.*
Revision: 2011 October
2012 JUKE
INL-20
< ECU DIAGNOSIS INFORMATION >
BCM
ECU DIAGNOSIS INFORMATION
BCM
WITH INTELLIGENT KEY
WITH INTELLIGENT KEY : List of ECU Reference
INFOID:0000000007578750
WITHOUT INTELLIGENT KEY
WITHOUT INTELLIGENT KEY : List of ECU Reference
INFOID:0000000007578751
ECU
Reference
BCM
BCS-57, "DTC Inspection Priority Chart"
ECU
Reference
BCM
BCS-122, "DTC Inspection Priority Chart"
Revision: 2011 October
2012 JUKE
INTERIOR ROOM LAMP CONTROL SYSTEM
INL-21
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
WIRING DIAGRAM
INTERIOR ROOM LAMP CONTROL SYSTEM
Wiring Diagram
INFOID:0000000007578752
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JRLWC1214GB
Revision: 2011 October
2012 JUKE
INL-22
< WIRING DIAGRAM >
INTERIOR ROOM LAMP CONTROL SYSTEM
JRLWC1215GB
Revision: 2011 October
2012 JUKE
ILLUMINATION
INL-23
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
ILLUMINATION
Wiring Diagram
INFOID:0000000007578753
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JRLWC1382GB
Revision: 2011 October
2012 JUKE
INL-24
< WIRING DIAGRAM >
ILLUMINATION
JRLWC1383GB
Revision: 2011 October
2012 JUKE
ILLUMINATION
INL-25
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
JRLWC1384GB
Revision: 2011 October
2012 JUKE
INL-26
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000007578754
OVERALL SEQUENCE
DETAILED FLOW
JMKIA8652GB
Revision: 2011 October
2012 JUKE
DIAGNOSIS AND REPAIR WORKFLOW
INL-27
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
1.
GET INFORMATION FOR SYMPTOM
1.
Get detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurs).
2.
Check operation condition of the function that is malfunctioning.
>> GO TO 2.
2.
CHECK DTC
1.
Check DTC.
2.
Perform the following procedure if DTC is detected.
-
Record DTC and freeze frame data (Print them out using CONSULT.)
-
Erase DTC.
-
Study the relationship between the cause detected by DTC and the symptom described by the customer.
3.
Check related service bulletins for information.
Are any symptoms described and any DTC detected?
Symptom is described, DTC is detected>>GO TO 3.
Symptom is described, DTC is not detected>>GO TO 4.
Symptom is not described, DTC is detected>>GO TO 5.
3.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Also study the normal operation and fail-safe related to the symptom.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected
again. At this time, always connect CONSULT to the vehicle, and check self diagnostic results in real time.
If two or more DTCs are detected, refer to DTC INSPECTION PRIORITY CHART, and determine trouble diag-
nosis order.
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC CONFIRMATION PROCEDURE is not included on Service
Manual. This simplified check procedure is an effective alternative though DTC cannot be detected during
this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC CONFIR-
MATION PROCEDURE.
Is DTC detected?
YES
>> GO TO 7.
NO
>> Check according to
GI-43, "Intermittent Incident"
.
6.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step
4, and determine the trouble diagnosis order based on possible causes and symptom.
Is the symptom described?
YES
>> GO TO 7.
NO
>> Monitor input data from related sensors or check voltage of related module terminals using CON-
SULT.
7.
DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE
Revision: 2011 October
2012 JUKE
INL-28
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
Inspect according to Diagnosis Procedure of the system.
Is malfunctioning part detected?
YES
>> GO TO 8.
NO
>> Check according to
GI-43, "Intermittent Incident"
.
8.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1.
Repair or replace the malfunctioning part.
2.
Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replace-
ment.
3.
Check DTC. If DTC is detected, erase it.
>> GO TO 9.
9.
FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the
malfunction is repaired securely.
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the
symptom is not detected.
Is DTC detected and does symptom remain?
YES-1 >> DTC is detected: GO TO 7.
YES-2 >> Symptom remains: GO TO 4.
NO
>> Before returning the vehicle to the customer, always erase DTC.
Revision: 2011 October
2012 JUKE
INTERIOR ROOM LAMP POWER SUPPLY CIRCUIT
INL-29
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
DTC/CIRCUIT DIAGNOSIS
INTERIOR ROOM LAMP POWER SUPPLY CIRCUIT
Description
INFOID:0000000007578755
Provides the interior room lamp power supply. Also cuts the power supply when the interior room lamp battery
saver activating.
Component Function Check
INFOID:0000000007578756
1.
CHECK INTERIOR ROOM LAMP POWER SUPPLY FUNCTION
CONSULT ACTIVE TEST
1.
Turn ignition switch ON.
2.
Turn each interior room lamp ON.
-
Map lamp
-
Luggage room lamp
3.
Select “BATTERY SAVER” of BCM (BATTERY SAVER) active test item.
4.
With operating the test items, check that each interior room lamp turns ON/OFF.
Does each interior room lamp turn ON/OFF?
YES
>> Interior room lamp power supply circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007578757
1.
CHECK INTERIOR ROOM LAMP POWER SUPPLY OUTPUT
CONSULT ACTIVE TEST
1.
Turn ignition switch OFF.
2.
Disconnect the following connectors.
-
Map lamp
-
Luggage room lamp
3.
Turn ignition switch ON.
4.
Select “BATTERY SAVER” of BCM (BATTERY SAVER) active test item.
5.
With operating the test item, check voltage between BCM harness connector and ground.
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK INTERIOR ROOM LAMP POWER SUPPLY OPEN CIRCUIT
Off
: Interior room lamp OFF
On
: Interior room lamp ON
BCM
(–)
Test item
Voltage
(Approx.)
(+)
Connector
Terminal
M69
56
Ground
BATTERY SAVER
Off
0 V
On
12 V
BCM
(–)
Test item
Voltage
(Approx.)
(+)
Connector
Terminal
M66
58
Ground
BATTERY SAVER
Off
0 V
On
12 V
Revision: 2011 October
2012 JUKE
INL-30
< DTC/CIRCUIT DIAGNOSIS >
INTERIOR ROOM LAMP POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect the BCM connector.
3.
Check continuity between BCM harness connector and each interior room lamp harness connector.
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> Check for internal short circuit of each interior room lamp.
NO
>> Repair or replace harnesses.
3.
CHECK INTERIOR ROOM LAMP POWER SUPPLY SHORT CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect the BCM connector.
3.
Check continuity between BCM harness connector and ground.
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> Repair or replace harnesses.
BCM
Each interior room lamp
Continuity
Connector
Terminal
Connector
Terminal
M69
56
Map lamp
R4
4
Existed
Luggage room lamp
B11
1
BCM
Each interior room lamp
Continuity
Connector
Terminal
Connector
Terminal
M66
58
Map lamp
R4
4
Existed
Luggage room lamp
B11
1
BCM
Ground
Continuity
Connector
Terminal
M69
56
Not existed
BCM
Ground
Continuity
Connector
Terminal
M66
58
Not existed
Revision: 2011 October
2012 JUKE
INTERIOR ROOM LAMP CONTROL CIRCUIT
INL-31
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
INTERIOR ROOM LAMP CONTROL CIRCUIT
Description
INFOID:0000000007578758
Controls each interior room lamp (ground side) by PWM signal.
NOTE:
PWM signal control period is approximately 250 Hz (in the gradual brightening/dimming).
Component Function Check
INFOID:0000000007578759
CAUTION:
Before performing the diagnosis, check that the following are normal.
• Interior room lamp power supply
• Map lamp bulb
1.
CHECK INTERIOR ROOM LAMP CONTROL FUNCTION
CONSULT ACTIVE TEST
1.
Switch the map lamp switch to DOOR.
2.
Turn ignition switch ON.
3.
Select “INT LAMP” of BCM (INT LAMP) active test item.
4.
With operating the test items, check that each interior room lamp turns ON/OFF (gradual brightening/dim-
ming).
Does the interior room lamp turns ON/OFF (gradual brightening/dimming)?
YES
>> Interior room lamp control circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007578760
1.
CHECK INTERIOR ROOM LAMP CONTROL OUTPUT
CONSULT ACTIVE TEST
1.
Turn ignition switch OFF.
2.
Remove all the bulbs of map lamp.
3.
Turn ignition switch ON.
4.
Select “INT LAMP” of BCM (INT LAMP) active test item.
5.
With operating the test item, check continuity between BCM harness connector and ground.
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> GO TO 2.
Fixed ON>>GO TO 3.
Fixed OFF>>Replace BCM. Refer to
BCS-80, "Removal and Installation"
.
2.
CHECK INTERIOR ROOM LAMP CONTROL OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector, map lamp connector.
On
: Interior room lamp gradual brightening
Off
: Interior room lamp gradual dimming
BCM
Ground
Test item
Continuity
Connector
Terminal
M69
63
INT LAMP
On
Existed
Off
Not existed
BCM
Ground
Test item
Continuity
Connector
Terminal
M66
60
INT LAMP
On
Existed
Off
Not existed
Revision: 2011 October
2012 JUKE
INL-32
< DTC/CIRCUIT DIAGNOSIS >
INTERIOR ROOM LAMP CONTROL CIRCUIT
3.
Check continuity between BCM harness connector and map lamp harness connector.
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> Replace map lamp.Refer to
INL-38, "Removal and Installation"
.
NO
>> Repair or replace harnesses.
3.
CHECK INTERIOR ROOM LAMP CONTROL SHORT CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and map lamp connector.
3.
Check continuity between BCM harness connector and ground.
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> Repair or replace harnesses.
BCM
Map lamp
Continuity
Connector
Terminal
Connector
Terminal
M69
63
R4
2
Existed
BCM
Map lamp
Continuity
Connector
Terminal
Connector
Terminal
M66
60
R4
2
Existed
BCM
Ground
Continuity
Connector
Terminal
M69
63
Not existed
BCM
Ground
Continuity
Connector
Terminal
M66
60
Not existed
Revision: 2011 October
2012 JUKE
LUGGAGE ROOM LAMP CIRCUIT
INL-33
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
LUGGAGE ROOM LAMP CIRCUIT
Description
INFOID:0000000007578761
Controls the luggage room lamp (ground side) to turn the luggage room lamp ON and OFF.
Diagnosis Procedure
INFOID:0000000007578762
CAUTION:
Before performing the diagnosis, check that the following are normal.
• Interior room lamp power supply
• Luggage room lamp bulb
1.
CHECK LUGGAGE ROOM LAMP OUTPUT
1.
Turn ignition switch OFF.
2.
Remove the luggage room lamp bulb.
3.
Check continuity between BCM harness connector and ground.
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> GO TO 2.
Fixed ON>>GO TO 3.
Fixed OFF>>Replace BCM. Refer to
BCS-80, "Removal and Installation"
.
2.
CHECK LUGGAGE ROOM LAMP OPEN CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and luggage room lamp harness connector.
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> Replace luggage room lamp.
NO
>> Repair or replace harnesses.
3.
CHECK LUGGAGE ROOM LAMP SHORT CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and ground.
BCM
Ground
Condition
Continuity
Connector
Terminal
B10
49
Back door
Open
Existed
Closed
Not existed
BCM
Ground
Condition
Continuity
Connector
Terminal
B9
55
Back door
Open
Existed
Closed
Not existed
BCM
Luggage room lamp
Continuity
Connector
(+)
Connector
(-)
Terminal
Terminal
B10
49
B11
2
Existed
BCM
Luggage room lamp
Continuity
Connector
(+)
Connector
(-)
Terminal
Terminal
B9
55
B11
2
Existed
Revision: 2011 October
2012 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст